Subrata Modak reported that building a CONFIG_RELOCATABLE kernel with
CONFIG_ISERIES enabled gives the following warnings:
WARNING: 4 bad relocations
c00000000007216e R_PPC64_ADDR16_HIGHEST __ksymtab+0x00000000009dcec8
c000000000072172 R_PPC64_ADDR16_HIGHER __ksymtab+0x00000000009dcec8
c00000000007217a R_PPC64_ADDR16_HI __ksymtab+0x00000000009dcec8
c00000000007217e R_PPC64_ADDR16_LO __ksymtab+0x00000000009dcec8
The reason is that decrementer_iSeries_masked is using
LOAD_REG_IMMEDIATE to get the address of a kernel symbol, which
creates relocations that aren't handled by the kernel relocator code.
Instead of reading the tb_ticks_per_jiffy variable, we can just set
the decrementer to its maximum value (0x7fffffff) and that will work
just as well. In fact timer_interrupt sets the decrementer to that
value initially anyway, and we are sure to get into timer_interrupt
once interrupts are reenabled because we store 1 to the decrementer
interrupt flag in the lppaca (LPPACADECRINT(r12) here).
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Configuring a powerpc 32 bit kernel for both SMP and SUSPEND turns on
CPU_HOTPLUG to enable disable_nonboot_cpus to be called by the common
suspend code. Previously the definition of cpu_die for ppc32 was in
the powermac platform code, causing it to be undefined if that platform
as not selected.
arch/powerpc/kernel/built-in.o: In function 'cpu_idle':
arch/powerpc/kernel/idle.c:98: undefined reference to 'cpu_die'
Move the code from setup_64 to smp.c and rename the power mac
versions to their specific names.
Note that this does not setup the cpu_die pointers in either
smp_ops (request a given cpu die) or ppc_md (make this cpu die),
for other platforms but there are generic versions in smp.c.
Reported-by: Matt Sealey <matt@genesi-usa.com>
Reported-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc strncmp implementation does not correctly handle a zero
length, despite the claim in 0119536cd3
(Add hand-coded assembly strcmp).
Additionally, all the length arguments are size_t, not int, so use
PPC_LCMPI and eq instead of cmpwi and le throughout.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There appear to be Pegasos systems which have the rtas-event-scan
RTAS tokens, but on which the event scan always fails. They also
have an event-scan-rate property containing 0, which means call
event scan 0 times per minute.
So interpret a scan rate of 0 to mean don't scan at all. This fixes
the problem on the Pegasos machines and makes sense as well.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The only way the debugger can handle a trap in inside rcu_lock,
notify_die, or atomic_notifier_call_chain without a recursive fault is
to allow the kernel debugger to handle the exception first in
program_check_exception().
The other change here is to make sure that kgdb_handle_exception() is
called with correct parameters when catching an oops, because kdb
needs to know if the entry was an oops, single step, or breakpoint
exception.
[benh@kernel.crashing.org: move debugger_bpt instead of #ifdef]
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These are the minimum changes to the kgdb core in order to enable an
API to connect a new front end (kdb) to the debug core.
This patch introduces the dbg_kdb_mode variable controls where the
user level I/O is routed. It will be routed to the gdbstub (kgdb) or
to the kdb front end which is a simple shell available over the kgdboc
connection.
You can switch back and forth between kdb or the gdb stub mode of
operation dynamically. From gdb stub mode you can blindly type
"$3#33", or from the kdb mode you can enter "kgdb" to switch to the
gdb stub.
The logic in the debug core depends on kdb to look for the typical gdb
connection sequences and return immediately with KGDB_PASS_EVENT if a
gdb serial command sequence is detected. That should allow a
reasonably seamless transition between kdb -> gdb without leaving the
kernel exception state. The two gdb serial queries that kdb is
responsible for detecting are the "?" and "qSupported" packets.
CC: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Martin Hicks <mort@sgi.com>
This patch contains the hooks and instrumentation into kernel which
live outside the kernel/debug directory, which the kdb core
will call to run commands like lsmod, dmesg, bt etc...
CC: linux-arch@vger.kernel.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Martin Hicks <mort@sgi.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
vmx and svm vcpus have different contents and therefore may have different
alignmment requirements. Let each specify its required alignment.
Signed-off-by: Avi Kivity <avi@redhat.com>
WARN() is used in some places to report firmware or hardware bugs that
are then worked-around. These bugs do not affect the stability of the
kernel and should not set the flag for TAINT_WARN. To allow for this,
add WARN_TAINT() and WARN_TAINT_ONCE() macros that take a taint number
as argument.
Architectures that implement warnings using trap instructions instead
of calls to warn_slowpath_*() now implement __WARN_TAINT(taint)
instead of __WARN().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Helge Deller <deller@gmx.de>
Tested-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch eliminates the node pointer from struct of_device and the
of_node (or prom_node) pointer from struct dev_archdata since the node
pointer is now part of struct device proper when CONFIG_OF is set, and
all users of the old pointer locations have already been converted over
to use device->of_node.
Also remove dev_archdata_{get,set}_node() as it is no longer used by
anything.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (311 commits)
perf tools: Add mode to build without newt support
perf symbols: symbol inconsistency message should be done only at verbose=1
perf tui: Add explicit -lslang option
perf options: Type check all the remaining OPT_ variants
perf options: Type check OPT_BOOLEAN and fix the offenders
perf options: Check v type in OPT_U?INTEGER
perf options: Introduce OPT_UINTEGER
perf tui: Add workaround for slang < 2.1.4
perf record: Fix bug mismatch with -c option definition
perf options: Introduce OPT_U64
perf tui: Add help window to show key associations
perf tui: Make <- exit menus too
perf newt: Add single key shortcuts for zoom into DSO and threads
perf newt: Exit browser unconditionally when CTRL+C, q or Q is pressed
perf newt: Fix the 'A'/'a' shortcut for annotate
perf newt: Make <- exit the ui_browser
x86, perf: P4 PMU - fix counters management logic
perf newt: Make <- zoom out filters
perf report: Report number of events, not samples
perf hist: Clarify events_stats fields usage
...
Fix up trivial conflicts in kernel/fork.c and tools/perf/builtin-record.c
When we build with ftrace enabled its possible that loadcam_entry would
have used the stack pointer (even though the code doesn't need it). We
call loadcam_entry in __secondary_start before the stack is setup. To
ensure that loadcam_entry doesn't use the stack pointer the easiest
solution is to just have it in asm code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In CONFIG_PTE_64BIT the PTE format has unique permission bits for user
and supervisor execute. However on !CONFIG_PTE_64BIT we overload the
supervisor bit to imply user execute with _PAGE_USER set. This allows
us to use the same permission check mask for user or supervisor code on
!CONFIG_PTE_64BIT.
However, on CONFIG_PTE_64BIT we map _PAGE_EXEC to _PAGE_BAP_UX so we
need a different permission mask based on the fault coming from a kernel
address or user space.
Without unique permission masks we see issues like the following with
modules:
Unable to handle kernel paging request for instruction fetch
Faulting instruction address: 0xf938d040
Oops: Kernel access of bad area, sig: 11 [#1]
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A future version of the MPC8610 HPCD's ASoC DMA driver will probe on individual
DMA channel nodes, so the DMA controller nodes' compatible string must be listed
in mpc8610_ids[] for the probe to work.
Also remove the "gianfar" compatible from mpc8610_ids[], since there is no
gianfar (or any other networking device) on the 8610.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are two front-panel LEDs on MPC837xRDB and MPC8315RDB boards: PWR
and HDD. After adding appropriate nodes we can program these LEDs from
kernel and user space.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since USB2 is shared with local bus, either local bus or USB2
should be disabled. By default U-Boot enables local bus, so we
have to disable USB2, otherwise kernel hangs:
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 28, io base 0xffe22000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
<hangs here>
Note that U-Boot doesn't clear 'status' property when it enables
USB2, so we have to comment out the whole node.
To enable USB2, one can issue
'setenv hwconfig usb2:dr_mode=<host|peripheral>' command at the
U-Boot prompt.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for eTSEC 2.0 as found in P1020.
The changes include introduction of the group nodes for
the etsec nodes.
Signed-off-by: Sandeep Gopalpet <sandeep.kumar@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Technically, whilst SEC v3.3 h/w honours the tls_ssl_stream descriptor
type, it lacks the ARC4 algorithm execution unit required to be able
to execute anything meaningful with it. Change the node to agree with
the documentation that declares that the sec3.3 really doesn't have such
a descriptor type.
Reported-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When we're on a paired single capable host, we can just always enable
paired singles and expose them to the guest directly.
This approach breaks when multiple VMs run and access PS concurrently,
but this should suffice until we get a proper framework for it in Linux.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
For KVM we need to find the location of the HTAB. We can either rely
on internal data structures of the kernel or ask the hardware.
Ben issued complaints about the internal data structure method, so
let's switch it to our own inquiry of the HTAB. Now we're fully
independend :-).
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We have some debug output in Book3S_64. Some of that was invalid though,
partially not even compiling because it accessed incorrect variables.
So let's fix that up, making debugging more fun again.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Book3S_64 didn't set VSID_PR when we're in PR=1. This lead to pretty bad
behavior when searching for the shadow segment, as part of the code relied
on VSID_PR being set.
This patch fixes booting Book3S_64 guests.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We have a condition in the ppc64 host mmu code that should never occur.
Unfortunately, it just did happen to me and I was rather puzzled on why,
because BUG_ON doesn't tell me anything useful.
So let's add some more debug output in case this goes wrong. Also change
BUG to WARN, since I don't want to reboot every time I mess something up.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
In the process of merging Book3S_32 and 64 I somehow ended up having the
alignment interrupt handler take last_inst, but the fetching code not
fetching it. So we ended up with stale last_inst values.
Let's just enable last_inst fetching for alignment interrupts too.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When in split mode, instruction relocation and data relocation are not equal.
So far we implemented this mode by reserving a special pseudo-VSID for the
two cases and flushing all PTEs when going into split mode, which is slow.
Unfortunately 32bit Linux and Mac OS X use split mode extensively. So to not
slow down things too much, I came up with a different idea: Mark the split
mode with a bit in the VSID and then treat it like any other segment.
This means we can just flush the shadow segment cache, but keep the PTEs
intact. I verified that this works with ppc32 Linux and Mac OS X 10.4
guests and does speed them up.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When we get a performance counter interrupt we need to route it on to the
Linux handler after we got out of the guest context. We also need to tell
our handling code that this particular interrupt doesn't need treatment.
So let's add those two bits in, making perf work while having a KVM guest
running.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
There are some pieces in the code that I overlooked that still use
u64s instead of longs. This slows down 32 bit hosts unnecessarily, so
let's just move them to ulong.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Now that we have all the bits and pieces in place, let's enable building
of the Book3S_32 target.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When an interrupt occurs we don't know yet if we're in guest context or
in host context. When in guest context, KVM needs to handle it.
So let's pull the same trick we did on Book3S_64: Just add a macro to
determine if we're in guest context or not and if so jump on to KVM code.
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
We have a define on what the highest bit of IRQ priorities is. So we can
just as well use it in the bit checking code and avoid invalid IRQ values
to be triggered.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We need the SWITCH_FRAME_SIZE define on Book3S_32 now too.
So let's export it unconditionally.
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
Our shadow MMU code needs to know where the HTAB is located and how
big it is. So we need some variables from the kernel exported to
module space if KVM is built as a module.
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
Some code we had so far required defines and had code that was completely
Book3S_64 specific. Since we now opened book3s.c to Book3S_32 too, we need
to take care of these pieces.
So let's add some minor code where it makes sense to not go the Book3S_64
code paths and add compat defines on others.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Book3S_32 doesn't know about segment faults. It only knows about page faults.
So in order to know that we didn't map a segment, we need to fake segment
faults.
We do this by setting invalid segment registers to an invalid VSID and then
check for that VSID on normal page faults.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We need to keep the pointer to the shadow vcpu somewhere accessible from
within really early interrupt code. The best fit I found was the thread
struct, as that resides in an SPRG.
So let's put a pointer to the shadow vcpu in the thread struct and add
an asm-offset so we can find it.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When instruction fetch failed, the inline function hook automatically
detects that and starts the internal guest memory load function. So
whenever we access kvmppc_get_last_inst(), we're sure the result is sane.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When we mapped a page as read-only, we can just release it as clean to
KVM's page claim mechanisms, because we're pretty sure it hasn't been
touched.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We just introduced generic segment switching code that only needs to call
small macros to do the actual switching, but keeps most of the entry / exit
code generic.
So let's move the SLB switching code over to use this new mechanism.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Since we now have several fields in the shadow VCPU, we also change
the internal calling convention between the different entry/exit code
layers.
Let's reflect that in the IR=1 code and make sure we use "long" defines
for long field access.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The real mode handler code was originally writen for 64 bit Book3S only.
But since we not add 32 bit functionality too, we need to make some tweaks
to it.
This patch basically combines using the "long" access defines and using
fields from the shadow VCPU we just moved there.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The host shadow mmu code needs to get initialized. It needs to fetch a
segment it can use to put shadow PTEs into.
That initialization code was in generic code, which is icky. Let's move
it over to the respective MMU file.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The shadow vcpu now contains some fields we don't use from the vcpu anymore.
Access to them happens using inline functions that happily use the shadow
vcpu fields.
So let's now ifdef them out to booke only and add asm-offsets.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
For assembly code there are several "long" load and store defines already.
The one that's missing is the typical stack store, stdu/stwu.
So let's add that define as well, making my KVM code happy.
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
Upstream recently added a new name for PPC64: Book3S_64.
So instead of using CONFIG_PPC64 we should use CONFIG_PPC_BOOK3S consotently.
That makes understanding the code easier (I hope).
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
So far we had a lot of conditional code on CONFIG_KVM_BOOK3S_64_HANDLER.
As we're moving towards common code between 32 and 64 bits, most of
these ifdefs can be moved to a more generic term define, called
CONFIG_KVM_BOOK3S_HANDLER.
This patch adds the new generic config option and moves ifdefs over.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
