Added a delay to give the frontend a little bit time for power-on.
Signed-off-by: Hartmut Birr <e9hack@googlemail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/dvb/ttpci/budget-ci.c:220:6: warning: "LINUX_VERSION_CODE" is not defined
drivers/media/dvb/ttpci/budget-ci.c:220:28: warning: "KERNEL_VERSION" is not defined
drivers/media/dvb/ttpci/budget-ci.c:220:42: error: missing binary operator before token "("
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This caused compilation to fail - completely replaced by new style
functions, so can be removed.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If your device is using the philips tda1316 tuner, i think there is a
problem in setting the correct Band. 162 MHz and above should be band 2
(Mid-Band). But in dvbc_philips_tdm1316l_tuner_set_params band 1 is set
for frequencies below 200 MHz.
Signed-off-by: Thomas Kaiser <linux-dvb@kaiser-linux.li>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change the debounce logic so that it is not used at all unless the
debounce parameter has been set. This makes for a much "snappier" remote
for most users as there is no timeout to wait for (the debounce logic has
a 350ms timer for the next repeat, but with the RC5 protocol, one event
per ~110ms is possible)
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds a ir_debug parameter which is useful in tracking down
IR decoding problems.
Based on Darren Salt's dvb-ir patchset.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Decode the RC5 device byte as well as the command byte. Introduce a
parameter to set the device events to listen for. Default to try
to auto-detect the proper device code, otherwise, listen to any
device as the old code did.
Based on Darren Salt's dvb-ir patchset.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This converts the budget-ci driver so that it uses ir-common for some of its
IR processing. In particular, the keymap for the Nova-T (sub 13c2:1011) is
switched to the Hauppauge grey/black keymap, of which the keys on the
supplied R808 remote control form a subset.
The old budget-ci keymap is moved to ir-keymaps.c and is used for other
remotes.
The debounce logic for buggy remotes (i.e. Zenith) is made conditional the
new debounce parameter and defaults to off (so that repeat keypresses aren't
ignored for all working remotes).
Some parts are based on Darren Salt's dvb-ir patchset.
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Trivial change to help the user understand what went wrong.
Taken from Darren Salt's dvb-ir patchset.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Improve the error checking in the IR init and deinit functions.
Based on Darren Salt's dvb-ir patchset.
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds a 'phys' string, of the same form as used by various other
DVB cards' IR drivers, for access by any program which uses the EVIOCPHYS
ioctl or may read /sys/class/input/*/phys (e.g. udev) to identify input
device nodes.
Taken from Darren Salt's dvb-ir patchset.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch lays down some groundwork for later budget-ci patches. The bulk
of this consists of moving a few members into a new struct and renaming a
few of them.
It also allocates extra space for the device name (the "name" field in
/proc/bus/input/devices and in the relevant sysfs dir) to avoid truncation
and uses snprintf rather than sprintf in case the extra space shouldn't be
enough.
Taken from Darren Salt's dvb-ir patchset
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- adhere to 80-column limit
- replace some spaces with tabs
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
For some reason, some of these cards have the tda10021 configured to a
different address. This adds support for such cards
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Also sprinkled some input_sync() throughout the code.
Acked-by: Ricardo Cerqueira <v4l@cerqueira.org>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for Satelco EasyWatch PCI DVBC cards
Signed-off-by: Thomas Hamm <thhamm@t-online.de>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix various .c/.h typos in comments (no code changes).
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
New module parameter diseqc_method for cards with subsystem-id 13c2:1003.
- 0: unreliable method, can be used by all board revisions (default)
- 1: reliable method, works for newer board layouts only
The parameter has no effect for cards with other subsystem-ids.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixes to DISEQC on these cards inadvertently broke normal tone/voltage
signalling. This restores the necessary function.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Technotrend 1500 T card have "inverted inversion". This patch fixes that.
Many thanks to Martin Zwickel from Technotrend for his confirmation and
correction proposal.
Signed-off-by: Raymond Mantchala <raymond.mantchala@streamvision.fr>
Signed-off-by: Perceval Anichini <perceval.anichini@streamvision.fr>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The IR chip has no address decoding, so the IR data is always present in
the high byte when doing a read from the saa7146 chip. This means that
the DEBI address used is irrelevant to the IR decoding logic.
DEBI addresses 0x1XXX are mapped to the registers on the CI module
itself, but only the lowest two bits are actually used (see EN50221,
section A.2.2.1), meaning that 0x1234 is equivalent to 0x1000 which maps
to register 0 (the data register). A read from the data register is
supposed to be preceded by a read from the size register, so some CI
modules will be confused (the AlphaCrypt CAM will hang completely).
The attached patch changes the address used when reading the IR data to
use 0x4000 instead. This is the CI version address, which is a safer
default, works with the AlphaCrypt CAM and matches the behaviour of the
Windows driver (AFAIK).
Signed-off-by: David Hrdeman <david@hardeman.nu>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement fix suggested by Michael Hunold for a bug reported
by Philipp Matthias Hahn: Starting "kdetv" on a Siemens DVB-C 1.x
produced an oops because kdetv opened "/dev/vbi0".
Remove the V4L2_CAP_VBI_CAPTURE flag because it does not work with
this type of hardware anyway.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Do not select FW_LOADER unless it is really required.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Port budget-av to use the new tua6100 driver
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Apparently there are two types of knc1 dvb-s plus cards with different tuners
(as for the knc1 dvb-s ones). This patch adds support for those cards with
subsystem id 1894:0011.
Successfully tested by: Benjamin Weber <benny1990@gmail.com>
Signed-off-by: Christoph Pfister <christophpfister@gmail.com>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This actually needs the same configuration as the other DVBC cards; simply
no one had managed to test before to find out.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
DVB null terminates its device names, which seems odd, and should be
unnecessary.
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some DVB-T cards with Grundig 29504-401 tuner use subsystem id 13c2:0001
(reported by Stuart Butterfield).
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I missed one call during the dvb_attach() development.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add the necessary code and makefile infrastructure
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only devices using > 1 frontend were ported; ones which did not are left
using static binding.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rewrote _write() calls to use write() op.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert SEC drivers to new frontend API
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since av7110.c is the only file actually using something from this
header, there's no reson for other files to
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Several DVB modules depends on I2C
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix bug reported by Andrew de Quincey:
After cold boot the saa7146 DMA did not start if the demuxer was opened
before the frontend has locked to the signal.
DMA transfers will be started now if (and only if)
the frontend is locked and data should be sent to the demuxer.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix typo in comment for TDA9819
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use the stv0299 native DISEQC implementation instead of the bitbanging one
as required by the ves1893. This was originally found by Oliver Endriss.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The original driver had a restriction that if a card as an saa7113 chip,
then it cannot have a CI interface. This is not the case.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These cards do not need the tda10021 configuration change when data is
streamed through a CAM module. This disables it for these ones.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added support for the msp34x5 audio dac. Analog sound output of
Technotrend DVB-C 2300 (aka Hauppauge Nexus-CA) works now.
Signed-off-by: Tim Kaiser <timkaiser@t-online.de>
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix missing $() on variable name in dvb/ttpci/Makefile
Fix AV7110 firmware dependencies so that parallel builds work correctly.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for Satelco EasyWatch DVB-S light card,
a clone of the KNC 1, with PCI subsystem ID 1894:001e
Signed-off-by: Lothar Englisch <Lothar.Englisch@lycos.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The dvb_frontend_ops is a pointer inside dvb_frontend. That's why every demod-driver
is having a field of dvb_frontend_ops in its private-state-struct and
using the reference for filling the pointer-field in dvb_frontend.
- It saves at least two lines of code per demod-driver,
- reduces object size (one less dereference per frontend_ops-access),
- be coherent with dvb_tuner_ops,
- makes it a little bit easier for newbies to understand how it works and
- avoids stupid mistakes because you would have to copy the dvb_frontend_ops
always, before you could assign the static pointer directly, which was
dangerous.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
