This adds support for the performance monitor hardware on the
MPC7450 family of processors (7450, 7451, 7455, 7447/7457, 7447A,
7448), used in the later Apple G4 powermacs/powerbooks and other
machines. These machines have 6 hardware counters with a unique
set of events which can be counted on each counter, with some
events being available on multiple counters.
Raw event codes for these processors are (PMC << 8) + PMCSEL.
If PMC is non-zero then the event is that selected by the given
PMCSEL value for that PMC (hardware counter). If PMC is zero
then the event selected is one of the low-numbered ones that are
common to several PMCs. In this case PMCSEL must be <= 22 and
the event is what that PMCSEL value would select on PMC1 (but
it may be placed any other PMC that has the same event for that
PMCSEL value).
For events that count cycles or occurrences that exceed a threshold,
the threshold requested can be specified in the 0x3f000 bits of the
raw event codes. If the event uses the threshold multiplier bit
and that bit should be set, that is indicated with the 0x40000 bit
of the raw event code.
This fills in some of the generic cache events. Unfortunately there
are quite a few blank spaces in the table, partly because these
processors tend to count cache hits rather than cache accesses.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: benh@kernel.crashing.org
LKML-Reference: <19000.55631.802122.696927@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This abstracts a few things in arch/powerpc/kernel/perf_counter.c
that are specific to 64-bit kernels, and provides definitions for
32-bit kernels. In particular,
* Only 64-bit has MMCRA and the bits in it that give information
about a PMU interrupt (sampled PR, HV, slot number etc.)
* Only 64-bit has the lppaca and the lppaca->pmcregs_in_use field
* Use of SDAR is confined to 64-bit for now
* Only 64-bit has soft/lazy interrupt disable and therefore
pseudo-NMIs (interrupts that occur while interrupts are soft-disabled)
* Only 64-bit has PMC7 and PMC8
* Only 64-bit has the MSR_HV bit.
This also fixes the types used in a couple of places, where we were
using long types for things that need to be 64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: benh@kernel.crashing.org
LKML-Reference: <19000.55590.634126.876084@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
At present, the powerpc generic (processor-independent) perf_counter
code has list of processor back-end modules, and at initialization,
it looks at the PVR (processor version register) and has a switch
statement to select a suitable processor-specific back-end.
This is going to become inconvenient as we add more processor-specific
back-ends, so this inverts the order: now each back-end checks whether
it applies to the current processor, and registers itself if so.
Furthermore, instead of looking at the PVR, back-ends now check the
cur_cpu_spec->oprofile_cpu_type string and match on that.
Lastly, each back-end now specifies a name for itself so the core can
print a nice message when a back-end registers itself.
This doesn't provide any support for unregistering back-ends, but that
wouldn't be hard to do and would allow back-ends to be modules.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: benh@kernel.crashing.org
LKML-Reference: <19000.55529.762227.518531@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This changes the powerpc perf_counter back-end to use unsigned long
types for hardware register values and for the value/mask pairs used
in checking whether a given set of events fit within the hardware
constraints. This is in preparation for adding support for the PMU
on some 32-bit powerpc processors. On 32-bit processors the hardware
registers are only 32 bits wide, and the PMU structure is generally
simpler, so 32 bits should be ample for expressing the hardware
constraints. On 64-bit processors, unsigned long is 64 bits wide,
so using unsigned long vs. u64 (unsigned long long) makes no actual
difference.
This makes some other very minor changes: adjusting whitespace to line
things up in initialized structures, and simplifying some code in
hw_perf_disable().
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: benh@kernel.crashing.org
LKML-Reference: <19000.55473.26174.331511@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This enables the perf_counter subsystem on 32-bit powerpc. Since we
don't have any support for hardware counters on 32-bit powerpc yet,
only software counters can be used.
Besides selecting HAVE_PERF_COUNTERS for 32-bit powerpc as well as
64-bit, the main thing this does is add an implementation of
set_perf_counter_pending(). This needs to arrange for
perf_counter_do_pending() to be called when interrupts are enabled.
Rather than add code to local_irq_restore as 64-bit does, the 32-bit
set_perf_counter_pending() generates an interrupt by setting the
decrementer to 1 so that a decrementer interrupt will become pending
in 1 or 2 timebase ticks (if a decrementer interrupt isn't already
pending). When interrupts are enabled, timer_interrupt() will be
called, and some new code in there calls perf_counter_do_pending().
We use a per-cpu array of flags to indicate whether we need to call
perf_counter_do_pending() or not.
This introduces a couple of new Kconfig symbols: PPC_HAVE_PMU_SUPPORT,
which is selected by processor families for which we have hardware PMU
support (currently only PPC64), and PPC_PERF_CTRS, which enables the
powerpc-specific perf_counter back-end.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: benh@kernel.crashing.org
LKML-Reference: <19000.55404.103840.393470@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* akpm: (182 commits)
fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset
fbdev: *bfin*: fix __dev{init,exit} markings
fbdev: *bfin*: drop unnecessary calls to memset
fbdev: bfin-t350mcqb-fb: drop unused local variables
fbdev: blackfin has __raw I/O accessors, so use them in fb.h
fbdev: s1d13xxxfb: add accelerated bitblt functions
tcx: use standard fields for framebuffer physical address and length
fbdev: add support for handoff from firmware to hw framebuffers
intelfb: fix a bug when changing video timing
fbdev: use framebuffer_release() for freeing fb_info structures
radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb?
s3c-fb: CPUFREQ frequency scaling support
s3c-fb: fix resource releasing on error during probing
carminefb: fix possible access beyond end of carmine_modedb[]
acornfb: remove fb_mmap function
mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF
mb862xxfb: restrict compliation of platform driver to PPC
Samsung SoC Framebuffer driver: add Alpha Channel support
atmel-lcdc: fix pixclock upper bound detection
offb: use framebuffer_alloc() to allocate fb_info struct
...
Manually fix up conflicts due to kmemcheck in mm/slab.c
Now we have __initconst, we can finally move the external declarations for
the various Linux logo structures to <linux/linux_logo.h>.
James' ack dates back to the previous submission (way to long ago), when the
logos were still __initdata, which caused failures on some platforms with some
toolchain versions.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: James Simmons <jsimmons@infradead.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* create mm/init-mm.c, move init_mm there
* remove INIT_MM, initialize init_mm with C99 initializer
* unexport init_mm on all arches:
init_mm is already unexported on x86.
One strange place is some OMAP driver (drivers/video/omap/) which
won't build modular, but it's already wants get_vm_area() export.
Somebody should look there.
[akpm@linux-foundation.org: add missing #includes]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Americo Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (103 commits)
powerpc: Fix bug in move of altivec code to vector.S
powerpc: Add support for swiotlb on 32-bit
powerpc/spufs: Remove unused error path
powerpc: Fix warning when printing a resource_size_t
powerpc/xmon: Remove unused variable in xmon.c
powerpc/pseries: Fix warnings when printing resource_size_t
powerpc: Shield code specific to 64-bit server processors
powerpc: Separate PACA fields for server CPUs
powerpc: Split exception handling out of head_64.S
powerpc: Introduce CONFIG_PPC_BOOK3S
powerpc: Move VMX and VSX asm code to vector.S
powerpc: Set init_bootmem_done on NUMA platforms as well
powerpc/mm: Fix a AB->BA deadlock scenario with nohash MMU context lock
powerpc/mm: Fix some SMP issues with MMU context handling
powerpc: Add PTRACE_SINGLEBLOCK support
fbdev: Add PLB support and cleanup DCR in xilinxfb driver.
powerpc/virtex: Add ml510 reference design device tree
powerpc/virtex: Add Xilinx ML510 reference design support
powerpc/virtex: refactor intc driver and add support for i8259 cascading
powerpc/virtex: Add support for Xilinx PCI host bridge
...
This fixes a couple of compile warnings that crept into the powerpc
perf_counter code recently:
CC arch/powerpc/kernel/perf_counter.o
arch/powerpc/kernel/perf_counter.c: In function 'record_and_restart':
arch/powerpc/kernel/perf_counter.c:1016: warning: unused variable 'addr'
arch/powerpc/kernel/perf_counter.c: In function 'hw_perf_counter_init':
arch/powerpc/kernel/perf_counter.c:891: warning: 'ev' may be used uninitialized in this function
Stephen Rothwell reported this against linux-next as well.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <18998.12884.787039.22202@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 28794d34 ("powerpc/kconfig: Kill PPC_MULTIPLATFORM"), added
CONFIG_PPC_OF_BOOT_TRAMPOLINE to control the buliding of prom_init.o
However the Makefile still unconditionally builds prom_init_check,
the script that checks prom_init.o for symbol usage, and so in turn
prom_init.o is still always being built. (it's not linked though)
So surround all the prom_init_check logic with an ifeq block testing
if CONFIG_PPC_OF_BOOT_TRAMPOLINE is set.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When CONFIG_RELOCATABLE is enabled, PHYSICAL_START is actually a
variable of type phys_addr_t. That means to print it we need to
cast to unsigned long long and use llx.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we are wasting time calling the generic calibrate_delay()
function. We don't need it since our implementation of __delay() is
based on the CPU timebase. So instead, we use our own small
implementation that initializes loops_per_jiffy to something sensible
to make the few users like spinlock debug be happy
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_counter: Start documenting HAVE_PERF_COUNTERS requirements
perf_counter: Add forward/backward attribute ABI compatibility
perf record: Explicity program a default counter
perf_counter: Remove PERF_TYPE_RAW special casing
perf_counter: PERF_TYPE_HW_CACHE is a hardware counter too
powerpc, perf_counter: Fix performance counter event types
perf_counter/x86: Add a quirk for Atom processors
perf_counter tools: Remove one L1-data alias
Sachin Sant reported these compiler errors:
CC arch/powerpc/kernel/power7-pmu.o
arch/powerpc/kernel/power7-pmu.c:297: error: PERF_COUNT_CPU_CYCLES undeclared here (not in a function)
Which happened because a last-minute rename of symbols crossed with
the Power7 support patch.
Fix this by using the new symbol names.
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@ozlabs.org
LKML-Reference: <1244788494.5554.1.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Everyone cut and paste this comment from my original one. We now do
it generically, so cut the comments.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Amerigo Wang <amwang@redhat.com>
The patch that moved to vector.S and made common between 32 and 64-bit the
altivec code had a nasty bug on 32-bit (did I really test that ?) which
causes the kernel to blr back into userspace ... oops :-)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The top (fastest) and last level (biggest) caches are the most
interesting ones, performance wise.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
[ Fixed the Nehalem LL table to LLC Reference/Miss events ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Pure renames only, to PERF_COUNT_HW_* and PERF_COUNT_SW_*.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This adds tables of event codes for the generalized cache events for
all the currently supported powerpc processors: POWER{4,5,5+,6,7} and
PPC970*, plus powerpc-specific code to use these tables when a
generalized cache event is requested.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <18992.36430.933526.742969@drongo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This adds the back-end for the PMU on POWER7 processors. POWER7
has 4 fully-programmable counters and two fixed-function counters
(which do respect the freeze conditions, can generate interrupts,
and are writable, unlike PMC5/6 on POWER5+/6).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <18992.36329.189378.17992@drongo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We currently log hw.sample_period for PERF_SAMPLE_PERIOD, however this is
incorrect. When we adjust the period, it will only take effect the next
cycle but report it for the current cycle. So when we adjust the period
for every cycle, we're always wrong.
Solve this by keeping track of the last_period.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For easy extension of the sample data, put it in a structure.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch includes the basic infrastructure to use swiotlb
bounce buffering on 32-bit powerpc. It is not yet enabled on
any platforms. Probably the most interesting bit is the
addition of addr_needs_map to dma_ops - we need this as
a dma_op because the decision of whether or not an addr
can be mapped by a device is device-specific.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
resource_size_t is 64 bits on PowerPC 64.
Gets rid of this warning:
arch/powerpc/kernel/pci_64.c: In function 'pcibios_map_io_space':
arch/powerpc/kernel/pci_64.c:504: warning: format '%016lx' expects type 'long unsigned int', but argument 2 has type 'resource_size_t'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a random collection of added ifdef's around portions of
code that only mak sense on server processors. Using either
CONFIG_PPC_STD_MMU_64 or CONFIG_PPC_BOOK3S as seems appropriate.
This is meant to make the future merging of Book3E 64-bit support
easier.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch has no effect other than re-ordering PACA fields on
current server CPUs. It however is a pre-requisite for future
support of BookE 64-bit processors. Various parts of the PACA
struct are now moved under some ifdef's, either the new
CONFIG_PPC_BOOK3S or CONFIG_PPC_STD_MMU_64, whatever seems more
appropriate.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.craashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To prepare for future support of Book3E 64-bit PowerPC processors,
which use a completely different exception handling, we move that
code to a new exceptions-64s.S file.
This file is #included from head_64.S due to some of the absolute
address requirements which can currently only be fulfilled from
within that file.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, load_up_altivec and give_up_altivec are duplicated
in 32-bit and 64-bit. This creates a common implementation that
is moved away from head_32.S, head_64.S and misc_64.S and into
vector.S, using the same macros we already use for our common
implementation of load_up_fpu.
I also moved the VSX code over to vector.S though in that case
I didn't make it build on 32-bit (yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reworked by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds block-step support on powerpc, including a PTRACE_SINGLEBLOCK
request for ptrace.
The BookE implementation is tweaked to fire a single step after a
block step in order to mimmic the server behaviour.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Counter type is a frequently used value and we do a lot of
bit juggling by encoding and decoding it from attr->config.
Clean this up by creating a separate attr->type field.
Also clean up the various similarly complex user-space bits
all around counter attribute management.
The net improvement is significant, and it will be easier
to add a new major type (which is what triggered this cleanup).
(This changes the ABI, all tools are adapted.)
(PowerPC build-tested.)
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit b23f3325 ("perf_counter: Rename various fields") fixed up
most of the uses of the renamed fields, but missed one instance
of "record_type" in powerpc-specific code which needs to be changed
to "sample_type", and a "PERF_RECORD_ADDR" in the same statement that
needs to be changed to "PERF_SAMPLE_ADDR", causing compilation
errors on powerpc. This fixes it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <18983.3111.770392.800486@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When using interrupting counters and limited (non-interrupting)
counters at the same time, it's possible that we get an
interrupt in write_mmcr0() after writing MMCR0 but before we
have set up the counters using limited PMCs. What happens then
is that we get into perf_counter_interrupt() with
counter->hw.idx = 0 for the limited counters, leading to the
"oops trying to read PMC0" error message being printed.
This fixes the problem by making perf_counter_interrupt()
robust against counter->hw.idx being zero (the counter is just
ignored in that case) and also by changing write_mmcr0() to
write MMCR0 initially with the counter overflow interrupt
enable bits masked (set to 0). If the MMCR0 value requested by
the caller has either of those bits set, we write MMCR0 again
with the requested value of those bits after setting up the
limited counters properly.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Kacur <jkacur@redhat.com>
Cc: Stephane Eranian <eranian@googlemail.com>
LKML-Reference: <18982.17684.138182.954599@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit ef923214 ("perf_counter: powerpc: use u64 for event
codes internally") introduced a bug where the return value from
function find_alternative_bdecode gets put into a u64 variable
and later tested to see if it is < 0. The effect is that we
get extra, bogus event code alternatives on POWER5 and POWER5+,
leading to error messages such as "oops compute_mmcr failed"
being printed and counters not counting properly.
This fixes it by using s64 for the return type of
find_alternative_bdecode and for the local variable that the
caller puts the value in. It also makes the event argument a
u64 on POWER5+ for consistency.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Kacur <jkacur@redhat.com>
Cc: Stephane Eranian <eranian@googlemail.com>
LKML-Reference: <18982.17586.666132.90983@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The structure isn't hw only and when I read event, I think about those
things that fall out the other end. Rename the thing.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Kacur <jkacur@redhat.com>
Cc: Stephane Eranian <eranian@googlemail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A few renames:
s/irq_period/sample_period/
s/irq_freq/sample_freq/
s/PERF_RECORD_/PERF_SAMPLE_/
s/record_type/sample_type/
And change both the new sample_type and read_format to u64.
Reported-by: Stephane Eranian <eranian@googlemail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Kacur <jkacur@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It was __devinit, but it is also within a CONFIG_HOTPLUG guarded section
of code, so the __devinit does nothing but cause the following warning:
WARNING: vmlinux.o(.text+0x107a8): Section mismatch in reference from the function pcibios_finish_adding_to_bus() to the function .devinit.text:pcibios_claim_one_bus()
The function pcibios_finish_adding_to_bus() references
the function __devinit pcibios_claim_one_bus().
This is often because pcibios_finish_adding_to_bus lacks a __devinit
annotation or the annotation of pcibios_claim_one_bus is wrong.
It is also only (externally) used in arch/powerpc/kernel/of_platform.c
which cannot be built as a module so don't export it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There's no need to wrap PPC_INST_NOP in a static inline.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These macros were used in the original port, but since commit
e4486fe316 (ftrace, use probe_kernel API to modify code) they
are unused.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use ppc_function_entry() from code-patching.h.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch updates the output from /proc/ppc64/lparcfg to display the
processor virtualization resource allocations for a shared processor
partition.
This information is already gathered via the h_get_ppp call, we just
have to make sure that the ibm,partition-performance-parameters-level
property is >= 1 to ensure that the information is valid.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Merge reason: merge almost-rc8 into perfcounters/core, which was -rc6
based - to pick up the latest upstream fixes.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The implementation we just revived has issues, such as using a
Kconfig-defined virtual address area in kernel space that nothing
actually carves out (and thus will overlap whatever is there),
or having some dependencies on being self contained in a single
PTE page which adds unnecessary constraints on the kernel virtual
address space.
This fixes it by using more classic PTE accessors and automatically
locating the area for consistent memory, carving an appropriate hole
in the kernel virtual address space, leaving only the size of that
area as a Kconfig option. It also brings some dma-mask related fixes
from the ARM implementation which was almost identical initially but
grew its own fixes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This implements interrupt throttling on powerpc. Since we don't have
individual count enable/disable or interrupt enable/disable controls
per counter, this simply sets the hardware counter to 0, meaning that
it will not interrupt again until it has counted 2^31 counts, which
will take at least 2^30 cycles assuming a maximum of 2 counts per
cycle. Also, we set counter->hw.period_left to the maximum possible
value (2^63 - 1), so we won't report overflows for this counter for
the forseeable future.
The unthrottle operation restores counter->hw.period_left and the
hardware counter so that we will once again report a counter overflow
after counter->hw.irq_period counts.
[ Impact: new perfcounters robustness feature on PowerPC ]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <18971.35823.643362.446774@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If CONFIG_PPC_EMULATED_STATS is enabled, make available counters for the
various classes of emulated instructions under
/sys/kernel/debug/powerpc/emulated_instructions/ (assumed debugfs is mounted on
/sys/kernel/debug). Optionally (controlled by
/sys/kernel/debug/powerpc/emulated_instructions/do_warn), rate-limited warnings
can be printed to the console when instructions are emulated.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
