This patch changes mac80211 to not notify the rate control algorithm's
tx_status() method when reporting status for a packet that didn't go
through the rate control algorithm's get_rate() method.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AP can switch dynamically between 20/40 Mhz channel width,
in which case we switch the local operating channel, but the
rate control algorithm is not notified. This patch adds a new callback
to indicate such changes to the RC algorithm.
Currently, HT channel width change is notified, but this callback
can be used to indicate any new requirements that might come up later on.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"Clearing" the rate control algorithm is pointless, none of
the algorithms actually uses this operation and it's not even
invoked properly for all channel switching. Also, there's no
need to since rate control algorithms work per station.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So after the previous changes we were still unhappy with how
convoluted the API is and decided to make things simpler for
everybody. This completely changes the rate control API, now
taking into account 802.11n with MCS rates and more control,
most drivers don't support that though.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Long awaited, hard work. This patch totally cleans up the rate control
API to remove the requirement to include internal headers outside of
net/mac80211/.
There's one internal use in the PID algorithm left for mesh networking,
we'll have to figure out a way to clean that one up and decide how to
do the peer link evaluation, possibly independent of the rate control
algorithm or via new API.
Additionally, ath9k is left using the cross-inclusion hack for now, we
will add new API where necessary to make this work properly, but right
now I'm not expert enough to do it. It's still off better than before.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As more preparation for a saner rate control algorithm API,
share the supported rates bitmap in the public API.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old infrastructure was:
- the default algorithm is built into mac80211
- other algorithms get into their own modules
The implementation of this complicated scheme was horrible
(just look at net/mac80211/Makefile), and anyone adding a new
algorithm would most likely not get it right at his first attempt.
This patch therefore builds all enabled algorithms into the mac80211
module.
The user interface for the rate control algorithms changes as follows:
- first the user can choose which algorithms to enable (currently only
MAC80211_RC_PID is available)
- if more than one algorithm is enabled (currently not possible since
only one algorithm is present) the user then chooses the default one
Note:
- MAC80211_RC_PID is always enables for CONFIG_EMBEDDED=n
Technical changes:
- all selected algorithms get into the mac80211 module
- net/mac80211/Makefile can now become much less complicated
- support for rc80211_pid_algo.c being modular is no longer required
- this includes unexporting mesh_plink_broken
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts mac80211 and all drivers to have transmit
information and status in skb->cb rather than allocating extra
memory for it and copying all the data around. To make it fit,
a union is used where only data that is necessary for all steps
is kept outside of the union.
A number of fixes were done by Ivo, as well as the rt2x00 part
of this patch.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch modifies struct ieee80211_tx_control to give band
info and the rate index (instead of rate pointers) to drivers.
This mostly serves to reduce the TX control structure size to
make it fit into skb->cb so that the fragmentation code can
put it there and we can think about passing it to drivers that
way in the future.
The rt2x00 driver update was done by Ivo, thanks.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames all mac80211 files (except ieee80211_i.h) to get rid
of the useless ieee80211_ prefix.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-04-08 16:44:45 -04:00
Renamed from net/mac80211/ieee80211_rate.h (Browse further)
