This patch fixes the low level debug UART io address as per this series.
The change is essential to have CONFIG_DEBUG_LL working.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Earlier BeagleBoards were using pad AH8 muxed to GPIO29 for MMC write-protect.
However, this signal has been changed to pad AG9 in board revision C2.
Fix this by adding mux configuration for pad AG9, runtime check for board
revisions and set the gpio number and pad muxing accordingly.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most board-*.c files read configuration data from the bootloader in
their .init_machine() function. This needs to happen earlier, at some
point before omap2_init_common_hw() is called. This is because a
future patch will use the bootloader serial console port information
to enable the UART clocks earlier, immediately after omap2_clk_init().
This is in turn necessary since otherwise clock tree usecounts on
clocks like dpll4_m2x2_ck will be bogus, which can cause the
currently-active console UART clock to be disabled during boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP tags are deprecrated so drop them.
Drop UART config data which decides which UARTs to enable during boot.
This is no longer necessary since serial core code disables clocks
after inactivity.
Background: with new UART idle code, all on-chip UARTs are idled using
a configurable inactivity timer (default 5 seconds.) After the
inactivity timer, UART clocks are disabled automatically.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patches ensures the MUX settings are correct for the SDRC
CKE signals to SDRAM. This allows the self-refresh to work when
2 chip-selects are in use.
A warning is thrown away in case the initial muxing is incorrect,
in order to track faulty or old-dated bootloaders.
Note: The CONFIG_OMAP_MUX and CONFIG_OMAP_MUX_WARNINGS options
must be enabled for the mux code to have effect.
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.
This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS
Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers
Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Initialize regulators for Beagle and Overo.
Patch is based on earlier patches posted to linux-omap mailing
list.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add timing data for the Micron MT46H32M32LF-6 SDRAM chip, used on the
OMAP3 Beagle and EVM boards. Original timing data is from the Micron
datasheet PDF downloaded from:
http://download.micron.com/pdf/datasheets/dram/mobile/1gb_ddr_mobile_sdram_t48m.pdf
Thanks to Rajendra Nayak <rnayak@ti.com> for his help identifying
the chips used on Beagle & OMAP3EVM.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a function omap2_gp_clockevent_set_gptimer() for board-*.c files
to use in .init_irq functions to configure the system tick GPTIMER.
Practical choices at this point are GPTIMER1 or GPTIMER12. Both of
these timers are in the WKUP powerdomain, and so are unaffected by
chip power management. GPTIMER1 can use sys_clk as a source, for
applications where a high-resolution timer is more important than
power management. GPTIMER12 has the special property that it has the
secure 32kHz oscillator as its source clock, which may be less prone
to glitches than the off-chip 32kHz oscillator. But on HS devices, it
may not be available for Linux use.
It appears that most boards are fine with GPTIMER1, but BeagleBoard
should use GPTIMER12 when using a 32KiHz timer source, due to hardware bugs
in revisions B4 and below. Modify board-omap3beagle.c to use GPTIMER12.
This patch originally used a Kbuild config option to select the GPTIMER,
but was changed to allow this to be specified in board-*.c files, per
Tony's request.
Kalle Vallo <kalle.valo@nokia.com> found a bug in an earlier version of
this patch - thanks Kalle.
Tested on Beagle rev B4 ES2.1, with and without CONFIG_OMAP_32K_TIMER, and
3430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Kalle Valo <kalle.valo@nokia.com>
Create a generic board-file for initializing usb
on omap2430 and omap3 boards.
Patch modified by Tony to build the module based on
CONFIG_USB_MUSB_SOC. Also merged in a patch adding
the nop xceiv from Ajay Kumar Gupta <ajay.gupta@ti.com>.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no CONFIG_I2C2_OMAP_BEAGLE in mainline and it is under
removal in linux-omap also so remove this dead code now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Changing it do 100kHz is needed to make more devices works properly. Controlling the
TI DLP Pico projector[1] doesn't work properly at 400kHz, 100kHz and lower work fine.
EDID readout is unaffected by this change.
[1] http://focus.ti.com/dlpdmd/docs/dlpdiscovery.tsp?sectionId=60&tabId=2234
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For a given SDRAM clock rate, SDRAM chips require memory controllers
to use a specific set of timing minimums and maximums to transfer data
reliably. These parameters can be different for different memory chips
and can also potentially vary by board.
This patch adds the infrastructure for board-*.c files to pass this
timing data to the SDRAM controller init function. The timing data is
specified in an 'omap_sdrc_params' structure, in terms of SDRC
controller register values. An array of these structs, one per SDRC
target clock rate, is passed by the board-*.c file to
omap2_init_common_hw().
This patch does not define the values for different memory chips, nor
does it use the values for anything; those will come in subsequent patches.
linux-omap source commit is bc84ecfc795c2d1c5cda8da4127cf972f488a696.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add low-level initialization for hsmmc controller. Merged into
this patch patch are various improvments and board support by
Grazvydas Ignotas and David Brownell.
Also change wire4 to be wires, as some newer controllers support
8 data lines.
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add minimal Beagle board support. Based on earlier patches
by Syed Mohammed Khasim with some fixes from linux-omap tree.
Signed-off-by: Syed Mohammed Khasim <khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
