Currently iwlagn is not able to report hw-killswitch events while the
interface is down. This has implications on user space tools (like
NetworkManager) relying on rfkill notifications to bring the interface
up once the wireless gets enabled through a hw killswitch.
Thus, enable the device already in iwl_pci_probe instead of iwl_up
and enable interrups while the interface is down in order to get
notified about killswitch state changes. The firmware loading is still
done in iwl_up.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the following warnings if compiled without CONFIG_IWLWIFI_DEBUG.
drivers/net/wireless/iwlwifi/iwl3945-base.c: In function ‘iwl3945_rx_reply_add_sta’:
drivers/net/wireless/iwlwifi/iwl3945-base.c:2748: warning: unused variable ‘pkt’
drivers/net/wireless/iwlwifi/iwl3945-base.c: In function ‘iwl3945_rx_scan_results_notif’:
drivers/net/wireless/iwlwifi/iwl3945-base.c:2903: warning: unused variable ‘notif’
drivers/net/wireless/iwlwifi/iwl3945-base.c: In function ‘iwl3945_rx_scan_complete_notif’:
drivers/net/wireless/iwlwifi/iwl3945-base.c:2928: warning: unused variable ‘scan_notif’
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To notice a negative keytype
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the led mode is asus, the activity led mode must
be registered otherwise the second LED will not be enabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
conf_tx() in rt61pci and rt73usb only have to check once
if the queue_idx indicates a non-WMM queue and break of
the function immediately if that is the case.
Only the WMM queues need to have the TX configuration written
to the registers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since driver now lives in separate subdirectory, move Kconfig entries
in own file so they can be tweaked indepndently. It complements
"orinoco: Move sources to a subdirectory".
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On Friday 16 January 2009 20:33:43 Kalle Valo wrote:
> N800 and N810 support is not on mainline yet, for stlc45xx I decided
> to add module parameters for the gpio numbers. Here's the commit from
> stlc45xx repo:
>
> 35afc5df00
This is the same patch for p54spi.
It removes all N800/N810 specific code from p54spi, so the driver can be used on
other architectures, or configurations as well.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A recent change in the usb core "USB: change interface to usb_lock_device_for_reset()"
conflicts with "p54usb: utilize usb_reset_device for 3887".
Sadly, we have to call usb_reset_device before we can upload the firmware on 3887.
Unless someone figures out how to reliably stop the 3887 so the hardware is still usable
next time we want to start it.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The buffer state is already cleared in ATH_TXBUF_RESET.
Remove redundant code clearing the type variable.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up the convoluted buffer management
logic for TX aggregation. Both aggregation creation and
completion are addressed.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the current holding descriptor is the last one in the TX queue,
*and* it has been marked as STALE, then move it to the free list
and bail out, as it has already been processed.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX queue draining routines have confusing names,
rename them approprately and merge ath_drain_txdataq()
with ath_drain_all_txq().
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch starts cleaning up all the crufty code in transmission path,
grouping functions into logical blocks.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate control algorithm needs to know if a STA allows
short guard interval, fixing this allows RC to use the correct
table.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calculation of rate indices from ratecode is done in recv.c
in a straightforward manner for both HT and legacy rates.
This variable is not needed anymore.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because we have support for the AR9100 devices now, we can enable them.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In 'ath9k_ani_reset' the 'ahp->ah_curani' will be initialized only
if 'DO_ANI(ah)' true. In 'ath9k_hw_ani_monitor' we are using
'ahp->ah_curani' unconditionally, and it will cause a NULL pointer
dereference on AR9100.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writing the register at offset 0x98c4 causes a deadlock on the AR913x
SoCs. Although i don't have detailed knowledge about these registers,
but if i change the register offset according to the 'ar5416Addac' table,
it works. Additionally there is no reference to the 0x98c4 elsewhere.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RTC register offsets don't fit into 'u16' on the AR913x, so we have
to remove the existing casts.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On the AR913x SOCs we have to provide EEPROM contents via platform_data,
because accessing the flash via MMIO is not safe. Additionally different
boards may store the radio calibration data at different locations.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the platform_driver itself, and modifies the main driver
to register it.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we have converted all bus specific routines to replaceable, we
can move the PCI specific codes into a separate file.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have left only some PCI specific cleanup code. We have to convert
them as well.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PCI specific bus_read_cachesize routine won't work on the AHB bus,
we have to replace it with a suitable one later.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert to use bus-agnostic DMA routines to make it usable on AHB bus as well.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert 'struct pci_dev' to 'struct device' to make it usable on the AHB
bus as well.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently iwl3945 is not able to report hw-killswitch events while the
interface is down. This has implications on user space tools (like
NetworkManager) relying on rfkill notifications to bring the interface
up once the wireless gets enabled through a hw killswitch.
Thus, enable the device already in iwl3945_pci_probe instead of iwl3945_up
and poll the CSR_GP_CNTRL register to update the killswitch state every
two seconds. The polling is only needed on 3945 hardware as this adapter
does not use interrupts to signal rfkill changes to the driver (in case no
firmware is loaded). The firmware loading is still done in iwl3945_up.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A recent pull from wireless testing generates the following warning:
CC [M] drivers/net/wireless/b43/main.o
drivers/net/wireless/b43/main.c: In function ‘b43_op_set_key’:
drivers/net/wireless/b43/main.c:3636: warning: pointer type mismatch
in conditional expression
This fix was suggested by Johannes Berg <johannes@sipsolutions.net>.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Silence sparse by using a defined value PCI_D3hot instead of a magic
constant in a pci_set_power_state() call.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At least one ar5211 card (GIGABYTE GN-WLMA101, 168c:0012 subsystem
1458:e800) reports itself as 11g capable which seems to be a bug in the
eeprom. initvals.c assumes that ar5211 is only 11b capable and thus refuses
to initialize this card. Hence this patch changes the probing for 11g
capabilities to discard 11g capabilities for ar5211 cards which allows this
specific card to work fine in 11b and 11a modes.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Usually every prism54 design hardware has a tiny eeprom chip in which all
device specific data for calibration and link-tuning is stored.
The stlc45xx chips are the only exception.
They are made for embedded devices, where space is scarce.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for longbow RF chip.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to upload pre-calculated calibration data to the firmware.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Under memory pressure, we may not be able to allocate a new skb for
new packets. If the allocation fails, ath5k_tasklet_rx will exit but
will leave a buffer in the list with a NULL skb, eventually triggering
a BUG_ON.
Extract the skb allocation from ath5k_rxbuf_setup() and change the
tasklet to allocate the next skb before accepting a packet.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch temporarily fixes a regression introduced by BT coexistence support.
There is an instability in connection when BT coexistence is enabled on some h/w.
This interim fix introduces a module parameter for BT coexistence configuration.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a check for LED_MODE_DEFAULT so that we use the link LED for rt2400
and rt2500 devices.
Signed-off-by: Andrew Price <andy@andrewprice.me.uk>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add initial support for libertas devices using a GSPI interface. This has
been tested with the 8686.
GSPI is intended to be used on embedded systems. Board-specific parameters are
required (see libertas_spi.h).
Thanks to everyone who took a look at the earlier versions of the patch.
Signed-off-by: Colin McCabe <colin@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 reserves 24 bytes in skb->cb for the driver.
So far, we only used them to keep track of used and free device memory.
But p54spi will need a slice of it, as well as the stuck frame detection.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Old firmwares had no problems processing frames which filled eighth of the memory window.
However we have to be a bit more careful with fat frames when we talk to new firmwares.
Apart from that, I confess the old logic was a bit weird and not very sophisticated.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
new kew -> a new key
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add GSPI constants to libertas core.
Fix misleading comment in lbs_setup_firmware.
Signed-off-by: Colin McCabe <colin@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl3945_init_drv() initialises the wrong lock, and sets the wrong power saving
default level.
With this power saving mode, we are losing a lot of frames in Ad-Hoc mode.
This is a bug fix for bug #1873.
( http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1873 )
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we're using iwl_mod_params, we want our module parameters names to be
in sync with the structure.
So, to set iwl_mod_params.sw_crypto, we'd better use a "swcrypto" parameter
name instead of the "hwcrypto" current one.
Moreover, by setting the decrypted flag properly, this patch also fixes the HW
crypto path for 3945 (the current code is not setting it when running HW
crypto).
This is a bug fix for bug #1872
( http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1872 )
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes 3945 use of hw_params.rx_buf_size instead of
IWL_RX_BUF_SIZE. It also renames IWL_RX_BUF_SIZE to IWL_RX_BUF_SIZE_3K
and moves rx buffer defines into iwl-fh.h.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
