When recently addressing remarks by Alexey Dobriyan about
the isp116x-hcd, I introduced a bug in the driver. Please
apply the attached patch to fix it.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch has a one line oops fix, plus related cleanups.
- The bugfix uses microframe scheduling data given to the hardware to
test "is this a periodic QH", rather than testing for nonzero period.
(Prevents an oops by providing the correct answer.)
- The cleanup going along with the patch should make it clearer what's
going on whenever those bitfields are accessed.
The bug came about when, around January, two new kinds of EHCI interrupt
scheduling operation were added, involving both the high speed (24 KBytes
per millisec) and low/full speed (1-64 bytes per millisec) microframe
scheduling. A driver for the Edirol UA-1000 Audio Capture Unit ran into
the oops; it used one of the newly supported high speed modes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In yenta_socket, we default to using the resource setting of the CardBus
bridge. However, this is a PCI-bus-centric view of resources and thus needs
to be converted to generic resources first. Therefore, add a call to
pcibios_bus_to_resource() call in between. This function is a mere wrapper on
x86 and friends, however on some others it already exists, is added in this
patch (alpha, arm, ppc, ppc64) or still needs to be provided (parisc -- where
is its pcibios_resource_to_bus() ?).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some PCI devices (e.g. 3c905B, 3c556B) lose all configuration
(including BARs) when transitioning from D3hot->D0. This leaves such
a device in an inaccessible state. The patch below causes the BARs
to be restored when enabling such a device, so that its driver will
be able to access it.
The patch also adds pci_restore_bars as a new global symbol, and adds a
correpsonding EXPORT_SYMBOL_GPL for that.
Some firmware (e.g. Thinkpad T21) leaves devices in D3hot after a
(re)boot. Most drivers call pci_enable_device very early, so devices
left in D3hot that lose configuration during the D3hot->D0 transition
will be inaccessible to their drivers.
Drivers could be modified to account for this, but it would
be difficult to know which drivers need modification. This is
especially true since often many devices are covered by the same
driver. It likely would be necessary to replicate code across dozens
of drivers.
The patch below should trigger only when transitioning from D3hot->D0
(or at boot), and only for devices that have the "no soft reset" bit
cleared in the PM control register. I believe it is safe to include
this patch as part of the PCI infrastructure.
The cleanest implementation of pci_restore_bars was to call
pci_update_resource. Unfortunately, that does not currently exist
for the sparc64 architecture. The patch below includes a null
implemenation of pci_update_resource for sparc64.
Some have expressed interest in making general use of the the
pci_restore_bars function, so that has been exported to GPL licensed
modules.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
prevent:
HOTPLUG_CPU=y
ACPI_PROCESSOR=y
ACPI_HOTPLUG_CPU=n
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The video driver doesn't properly remove all the notify handlers
on module unload. This has a side effect of subdevices failing
to register on module reload, but sudden death looms if the
handlers trigger after the module is unloaded.
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This code was never designed to handle more than one instance of do_work()
running at once.
Signed-Off-By: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The recent change to never ignore the bitmap, revealed that the bitmap isn't
begin flushed properly when an array is stopped.
We call bitmap_daemon_work three times as there is a three-stage pipeline for
flushing updates to the bitmap file.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Firstly, R1BIO_Degraded was being set in a number of places in the resync
code, but is never used there, so get rid of those settings.
Then: When doing a resync, we want to clear the bit in the bitmap iff the
array will be non-degraded when the sync has completed. However the current
code would clear the bitmap if the array was non-degraded when the resync
*started*, which obviously isn't right (it is for 'resync' but not for
'recovery' - i.e. rebuilding a failed drive).
This patch calculated 'still_degraded' and uses the to tell bitmap_start_sync
whether this sync should clear the corresponding bit.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code currently will ignore the bitmap if the array seem to be in-sync.
This is wrong if the array is degraded, and probably wrong anyway. If the
bitmap says some chunks are not in in-sync, and the superblock says everything
IS in sync, then something is clearly wrong, and it is safer to trust the
bitmap.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Until the bitmap code was added,
modprobe md
would load the md module. But now the md module is called 'md-mod', so we
really need an alias for backwards comparability.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
no_overlay bttv parameter implemented to fix OOPS on some PCI chipsets
(like some VIA) with these behaviors:
1) If pci_quicks does identify the chip as having troubles to
handle PCI2PCI transfers, no_overlay defaults to 1. The user may force
it to 0, to reenable (not recommended).
2) For newer chipsets not blacklisted, no_overlay=1 is provided as a
workaround until PCI chipset included on /drivers/pci/quirks.c
Thanks to Bodo Eggert <7eggert@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch fixes oops caused by ide interfaces not on pci. pcibus_to_node
causes the kernel to crash otherwise. Patch also adds a BUG_ON to check if
hwif is NULL.
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Cc: Andi Kleen <ak@muc.de>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Several people noticed we dropped quite a bit on benchmark figures.
OK, it was my fault but unfortunately I discovered I ran out of brown
paper bags a while ago and forgot to reorder them.
The issue is that a construct introduced in the conversion of the
driver to use the transport class keyed off whether the block request
was tagged or not. However, the aic7xxx driver doesn't properly set
up the block layer TCQ (it uses the wrong API), so the driver now
things all requests are untagged and we keep it to a queue depth of a
single element. Oops.
The fix is to use the correct TCQ API.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
commit from running until a change has been made in
the destination. In this instance the desired result
was to choose the destination version of the file
and ignore the source version, but git would not
allow that.
Here I added a blank line to let git commit think
I resolved a merge conflict.
ACPI now uses kmalloc(...,GPF_ATOMIC) during suspend/resume.
http://bugzilla.kernel.org/show_bug.cgi?id=3469
Signed-off-by: David Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
For 2.6.12 behaviour, this (EXPERIMENTAL) driver
should not be built.
Update the driver source with latest from Luming.
Signed-off-by: Luming Yu <luming.yu@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Burst mode isn't ready for prime time,
but can be enabled for test via "ec_burst=1"
Signed-off-by: Luming Yu <luming.yu@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Patch from Ian Campbell
On PXA255 there is no way to disable the watchdog. Turning off OIER[E3]
as suggested in the existing comment does not work.
I posted a note to the ARM mailing list a little while ago asking for
opinions from people using SA1100. There was one reponse from Nico who
believes that the SA1100 is the same as the PXA255 in this respect.
You also asked me to involve the watchdog maintainer which I tried to
do but didn't hear anything back. There are only a couple of other
drivers which can't stop the watchdog and there seems to be no
consistancy regarding printing an error etc. I decided to print
something since that matches the case for all the other drivers when
NOWAYOUT is turned on.
Also, I changed the device .name to "watchdog" like most of the other
watchdogs. udev uses it as the device name (by default) and spaces etc.
get in the way.
Superceded 2833/1 because 2.6.13-rc4 caused rejects.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch disables the PCI Interrupt Link refernece counts,
which should not co-exist with the 2.6.12 irq_router.resume
method or else a double acpi_pci_link_set() could result
on resume.
Signed-off-by: David Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We have increased PCIBIOS_MIN_IO to 0x4000, but still want
motherboard resources to be allocated properly. So we need
to state 0x1000 (according to the comment) limit explicitely.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The reason we have PCIBIOS_MIN_IO and PCIBIOS_MIN_CARDBUS_IO is because
we want to protect badly documented motherboard PCI resources and thus
don't want to allocate new resources in low IO/MEM space.
However, if we have already discovered a PCI bridge with a specified
resource base, that should override that decision.
This change will allow us to move the "careful" region upwards without
resulting in problems allocating resources in low mappings. This was
brought on by us having allocated a bus resource at 0x1000, conflicting
with a undocumented VAIO Sony PI resources.
CFQ will currently stall when using write barriers and the default
max_depth setting of 1, since we artificially need a depth of 2 when
pre-pending the first flush. So never deny the barrier request going to
the device.
This is a regression since 2.6.12, it was found in SUSE testing.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The aic7xxx can support Data Group transfers at periods > 12.5, so
eliminate that restriction. Additionally wide is a requirement for DT
so ensure wide is set if users request DT.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rebuild the aic7xxx firmware doesn't work anymore after this change
which appeared int 2.6.13-rc1:
[SCSI] aic7xxx/aic79xx: remove useless byte order macro cruft
Two files did not include byteorder.h, resulting in aic dying with a panic
"Unknown opcode encountered in seq program"
This fixes it for me.
Signed-off-by: Olaf Hering <olh@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Recent changes (well, dating from 12 July) have broken cardbus on my
powerbook: I get 3 messages saying "no resource of type xxx available,
trying to continue", and if I plug in my wireless card, it complains
that there are no resources allocated to the card. This all worked in
2.6.12.
Looking at the code in yenta_socket.c, function yenta_allocate_res,
it's obvious what is wrong: if we get to line 639 (i.e. there wasn't a
usable preassigned resource), we will always flow through to line 668,
which is the printk that I was seeing, even if a resource was
successfully allocated. It looks to me as though there should be a
return statement after the two config_writel's in each of the 3
branches of the if statements, so that the function returns after
successfully setting up the resource.
The patch below adds these return statements, and with this patch,
cardbus works on my powerbook once again.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removing the SCSI tape module results in an oops in class_device_destroy if
any devices are present. The patch at the end of this message fixes the bug
by moving class_destroy() later in exit_st() so that the class still exists
when devices are removed. (The bug is old but class_simple_device_remove() did
nothing when the class did not exist.)
The patch also fixes a "class leak" in init_st() error path.
I would like to get this into 2.6.13 but it may be too late?
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I am resubmitting the 2.6 kernel patch for the Version 7.12.02 ips driver.
I have eliminated a couple of inappropriate changes pointed out by Arjan.
Signed-off-by: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch does correct radio chip autodetection to avoid misdetecting
mt20xx microtune as tea5767 chip.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Martin Drab found that he could get aacraid timeouts with high load on his
controller / disk drive combinations. After some experimentation Mark
Salyzyn has come up with a patch to reduce the default max_sectors to
something that will keep the controller from being overloaded and will
eliminate the timeout issues.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cs89x0 talks a lot at boot. Seems like debug leftover. This patch
downgrades printks to KERN_DEBUG. While we're at it, make these messages a
bit less obscure.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The default resync_max_sector is set to "mddev->size << 1". If the
raid-personality-module updates mddev->size, it must update
resync_max_sectors too.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Peter Missel:
- Add support for the SVideo input on the GDI Black Gold.
Mauro Carvalho Chehab:
- Linux/version.h removed. Replaced by linux/utsname.h
Michael Krufky:
- Added analog support for DViCO FusionHDTV5 Gold.
CC: Peter Missel <peter.missel@onlinehome.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fixed some bttv card numbers.
- BTTV and SAA7134 version numbers incremented to reflect changes.
- pci_dma_supported() is called after pci_set_dma_mask() which
already did check that for us. This patch removes the unneeded call to
pci_dma_supported() at bttv-driver.c
- Ensure a sufficient I2C bus idle time between 2 messages for
saa7134-i2c.c
- It is important to write at first to MO_GP3_IO for cx88-tvaudio.c
- Use try_to_freeze() instead of refrigerator at msp3400.c
- Recognizing the MFPE05-2 Tuner at tveeprom.c
- Add new parameter to help identify radio chipsets at tuner module:
show_i2c=1 will show 16 reading bytes from detected tuners.
- BTTV does generate some Unimplemented IOCTL log at tuner module:
0x40046d11(dir=1,tp=0x6d,nr=17,sz=4) means that it is sending
MSP3400 calls to non-msp3400 tuners. Warning eliminated.
VIDIOSAUDIO is also called, so debug messages updated. It is still
requiring IOCTL implementation.
- Added two more tuners.
- Add support for the SVideo input on the GDI Black Gold.
Signed-off-by: Peter Missel <peter.missel@onlinehome.de>
Signed-off-by: Graham Bevan <graham.bevan@ntlworld.com>
Signed-off-by: Torsten Seeboth <Torsten.Seeboth@t-online.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t.online.de>
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make it compile with CONFIG_PM=n
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Seems that both Greg and I submitted the same patch and it just kept on
applying...
Cc: Greg KH <greg@kroah.com>
Cc: Kumar Gala <galak@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If there are devices that use interrupts over a suspend event, ACPI must
restore the PCI interrupt links on resume. Anything else breaks any
device that hasn't been converted to the new (dubious) PM rules.
Drivers that need the irq free/re-aquire sequence can be done one by one
independently of this one.
Reported by: Jochen Hein (Bugzilla Bug 4312)
When there is disk I/O happening, the framebuffer has a little snow on
the screen. Once I/O has finished, no garbage remains on screen.
This bug was explained by: Knut Petersen
Most important is CRTC register 2f, signal quality is also improved for
higher vclk values by changing set_vclk() according to the X drivers and
cyblafb.c
The fix is to set the performance register (0x2f) with a more stable
value.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reported by: Jochen Hein (Bugzilla Bug 4386)
booting leaves the end of long lines in the last line on screen when
scrolling. When X is running, scrolling puts garbage on the screen
(looks like X data) Console switch fixes the screen. Behaviour seems to
be identical with noaccel and without on the video=tridentfb parameter
in lilo.conf.
This bug was explained by: Knut_Petersen
Acceleration is broken for all BLADE 3D chips for all versions of kernel
2.6 except for 32bit modes. Most important reason is that the u32 col
parameter of the graphics engine needs the color value replicated to all
u8 of the u32 (8bit modes) and to both u16 of the u32.
Fix color value passed to graphics engine, verified by the reporter.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ordering of setting and clearing device_add_pending went wrong on some
occasions, causing multifunction cards only to be handled correctly on the
first insertion, not on subsequent ones.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid registering PCMCIA CF cards before other IDE stuff. This means the risk
of /dev/hd* being re-ordered is lessened. The _sane_ thing to assert any
ordering is to use udev, nameif and so on, of course.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch displays the name of the fbdev driver in sysfs.
Down the road this will replace the current proc handle we have.
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Drivers really only work well in SMP if they actually can be selected.
This is a leftover from the time when the 6pack drive only used to be
a bitrotten variant of the slip driver.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Kconfig | 2 +-
1 files changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
--ReaqsoxgOBHFXBhH
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
Hi Jeff,
Here's a little patch fixing a typo in smc91x.h.
Regards,
Tony
--ReaqsoxgOBHFXBhH
Content-Type: text/x-chdr; charset=us-ascii
Content-Disposition: inline; filename="patch-fix-typo-smc91x.h"
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Yukon-Lite chipset needs workaround for revision 7 (or later).
Without this patch, chip gets stuck in low power mode and never
boots. Newer SysKonnect vendor code already had same patch.
Related bug in skge is http://bugs.gentoo.org/87822
Chris, please add for 2.6.12.2
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
SCSI=m must disallow static drivers.
The problem is that all the SATA drivers depend on SCSI_SATA.
With SCSI=m and SCSI_SATA=y this allows the static enabling of the SATA
drivers with unwanted effects, e.g.:
- SCSI=m, SCSI_SATA=y, SCSI_ATA_ADMA=y
-> SCSI_ATA_ADMA is built statically but scsi/built-in.o is not linked
into the kernel
- SCSI=m, SCSI_SATA=y, SCSI_ATA_ADMA=y, SCSI_SATA_AHCI=m
-> SCSI_ATA_ADMA and libata are built statically but
scsi/built-in.o is not linked into the kernel,
SCSI_SATA_AHCI is built modular (unresolved symbols due to missing
libata)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleanup code that is used to toggle LED's. Since we
get called from ethtool, can use that thread rather than
setting up a timer.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
During autonegotiation set PHY interrupt mask to ignore
bogus speed change interrupts.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The code to clear fifo errors was incorrect and sending garbage
to the external phy. Removed the no longer used inline's funcs.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The check for Yukon lite changes was restricting itself to
rev A3. It turns out that these changes are also true on A4
and later.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleanup the phy_lock deadlock because of relocking in the nway_reset path.
Reported by Francois Romieu.
Also, don't need to do irqsave/restore for blink,
just excluding bh is good enough.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Here is a fix for a typo, thanks Eliot Dresselhaus.
Since transmitter not active when device is down, it wasn't really noticed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The SK-9E boards use the Marvell Yukon2 chipset which
is not supported by the skge driver. Thanks to Ralph Roesler
for noticing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Using Genesis board, I get harmless error reports. Rather than console
error, turn it into a error counter.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ACPI is wrong. Devices should not release their IRQ's on suspend and
re-aquire them on resume. ACPI should just re-init the IRQ controller
instead of breaking most drivers very subtly.
Breakage reported by Hugh Dickins <hugh@veritas.com>
Undo: d8c4b4195c
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
An early version of the sk98lin patch was merged via Len's tree. But there
were subsequent updates as a result of review from Jeff. THis fixes things
up.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Basically DT isn't reported or handled at all. The problem is that
lines of code like this:
spi_dt(starget) = tinfo->curr.ppr_options & MSG_EXT_PPR_DT_REQ;
don't do what you think they do when spi_dt is a single bit variable.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
drivers/fc4/fc.c: In function `fcp_scsi_dev_reset':
drivers/fc4/fc.c:933: warning: control reaches end of non-void function
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes srp.h which uses 0x80 for SRP_LOGIN_REJ instead of
0xc2.
Signed-off-by: Linda Xie <lxie@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Implemented support to ignore an attempt to install/load
a particular ACPI table more than once. Apparently there
exists BIOS code that repeatedly attempts to load the same
SSDT upon certain events. Thanks to Venkatesh Pallipadi.
Restructured the main interface to the AML parser in
order to correctly handle all exceptional conditions. This
will prevent leakage of the OwnerId resource and should
eliminate the AE_OWNER_ID_LIMIT exceptions seen on some
machines. Thanks to Alexey Starikovskiy.
Support for "module level code" has been disabled in this
version due to a number of issues that have appeared
on various machines. The support can be enabled by
defining ACPI_ENABLE_MODULE_LEVEL_CODE during subsystem
compilation. When the issues are fully resolved, the code
will be enabled by default again.
Modified the internal functions for debug print support
to define the FunctionName parameter as a (const char *)
for compatibility with compiler built-in macros such as
__FUNCTION__, etc.
Linted the entire ACPICA source tree for both 32-bit
and 64-bit.
Signed-off-by: Robert Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add reference count and disable ACPI PCI Interrupt Link
when no device still uses it.
Warn when drivers have not released Link at suspend time.
http://bugzilla.kernel.org/show_bug.cgi?id=3469
Signed-off-by: David Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
EC burst mode benefits many machines, some of
them significantly. However, our current
implementation fails on some machines such
as Rafael's Asus L5D.
This patch restores the alternative EC polling code,
which can be enabled at boot time via "ec_polling"
http://bugzilla.kernel.org/show_bug.cgi?id=4665
Signed-off-by: Luming Yu <luming.yu@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When leaving S3 state, the AGP bridge may not have all PCI configuration
registers set in the same way as they were at boot. This should be fixed
by pci_restore_state - however, the APBASE register cannot be set to
conflict with the APSIZE register. If APSIZE is larger than it was before
suspend, pci_restore_state will not restore APBASE correctly. The attached
patch adds an extra item to the agp_bridge_data structure and uses it to
store the value of APBASE. On resume, this is then written after APSIZE
has been set. This patch only touches the path used for Intel chipsets
without integrated graphics, and may need to be extended to work with the
others.
Without this patch, I get the symptoms described in bug 4921 - APBASE ends
up overlapping various PCI devices, and as a result they fail to work after
resume.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Close a small window where a device may be not operational again after senseid
finished and the "same device" check fails due to dev=0000 by checking for dnv
after stsch() by then setting the device to not operational. (No need to
check for dnv in ccw_device_handle_oper() again since we don't do stsch() into
the subchannel's schib in the meantime and will get a crw anyway if the device
becomes not oper again).
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not use memcpy in fb_pad_aligned_buffer. It is suboptimal because only
a few bytes are moved at a time. Replace with a for-loop.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
>> vesafb: mode is 800x600x16, linelength=1600, pages=16
>> vesafb: scrolling: redraw
>> vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
>> mtrr: type mismatch for fc000000,1000000 old: write-back new: write-
>> combining
Range is already set to write-back, vesafb attempts to add a write-combining
mtrr (default for vesafb).
>> mtrr: size and base must be multiples of 4 kiB
This is a bug, vesafb attempts to add a size < PAGE_SIZE triggering
the messages below.
To eliminate the warning messages, you can add the option mtrr:2 to add a
write-back mtrr for vesafb. Or just use nomtrr option.
1. Fix algorithm for finding the best power of 2 size with mtrr_add().
2. Add option to choose the mtrr type by extending the mtrr boot option:
mtrr:n where n
0 = no mtrr (equivalent to using the nomtrr option)
1 = uncachable
2 = write back
3 = write combining (default)
4 = write through
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for UARTs in MMIO space and clean up a little whitespace.
HP legacy-free ia64 machines need this.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
