Because we need to transfer some bytes with PIO, the msg length is not
the length of the DMA buffer. Use the correct value which we used when
doing the mapping.
Fixes: 73e8b05283 ("i2c: rcar: add DMA support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Architecturally we should apply a 0x400 offset for these. Not doing
it will break future HW implementations.
The offset of 0 is supposed to remain for "triggers" though not all
sources support both trigger and store EOI, and in P9 specifically,
some sources will treat 0 as a store EOI. But future chips will not.
So this makes us use the properly architected offset which should work
always.
Fixes: 243e25112d ("powerpc/xive: Native exploitation of the XIVE interrupt controller")
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The client ID 0 is reserved by the host1x/cdma to mark the timeout timer
work as already been scheduled and context ID is used as the clients one.
This fixes spurious CDMA timeouts.
Fixes: bdd2f9cd10 ("drm/tegra: Don't leak kernel pointer to userspace")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/9c19a44219acd988e678cf9abe21363911184625.1497480754.git.digetx@gmail.com
If 'devm_reset_control_get' returns an error, then we erroneously return
success because error code is taken from 'host->clk' instead of
'host->rst'.
Fixes: b386c6b73a ("gpu: host1x: Support module reset")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170410202922.17665-1-christophe.jaillet@wanadoo.fr
Before accessing DMI data to record it for later, we should ensure
that the DMI structures are large enough to contain the data in
question.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
This is not sensitive information like serial numbers, we can allow
all users to read it.
Fix odd alignment while we're here.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: c61872c983 ("firmware: dmi: Add DMI_PRODUCT_FAMILY identification string")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Currently they return -1 on error, which will confuse callers if
they try to interpret it as a normal negative error code.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Since version 3.0.0 of the SMBIOS specification, there can be
multiple entry points in memory, pointing to one or two DMI tables.
If both a 32-bit ("_SM_") entry point and a 64-bit ("_SM3_") entry
point are present, the specification requires that the latter points
to a table which is a super-set of the table pointed to by the
former. Therefore we should give preference to the 64-bit ("_SM3_")
entry point.
However, currently the code is picking the first valid entry point
it finds. Per specification, we should look for a 64-bit ("_SM3_")
entry point first, and if we can't find any, look for a 32-bit
("_SM_" or "_DMI_") entry point. Modify the code to do that.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 4f757f3cbf ("make sure that mntns_install() doesn't end up with referral for root")
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
It's not hard to trigger a bunch of d_invalidate() on the same
dentry in parallel. They end up fighting each other - any
dentry picked for removal by one will be skipped by the rest
and we'll go for the next iteration through the entire
subtree, even if everything is being skipped. Morevoer, we
immediately go back to scanning the subtree. The only thing
we really need is to dissolve all mounts in the subtree and
as soon as we've nothing left to do, we can just unhash the
dentry and bugger off.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The .its targets require information about the kernel binary, such as
its entry point, which is extracted from the vmlinux ELF. We therefore
require that the ELF is built before the .its files are generated.
Declare this requirement in the Makefile such that make will ensure this
is always the case, otherwise in corner cases we can hit issues as the
.its is generated with an incorrect (either invalid or stale) entry
point.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: cf2a5e0bb4 ("MIPS: Support generating Flattened Image Trees (.itb)")
Cc: linux-mips@linux-mips.org
Cc: stable <stable@vger.kernel.org> # v4.9+
Patchwork: https://patchwork.linux-mips.org/patch/16179/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code handling the pop76 opcode (ie. bnezc & jialc instructions) in
__compute_return_epc_for_insn() needs to set the value of $31 in the
jialc case, which is encoded with rs = 0. However its check to
differentiate bnezc (rs != 0) from jialc (rs = 0) was unfortunately
backwards, meaning that if we emulate a bnezc instruction we clobber $31
& if we emulate a jialc instruction it actually behaves like a jic
instruction.
Fix this by inverting the check of rs to match the way the instructions
are actually encoded.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 28d6f93d20 ("MIPS: Emulate the new MIPS R6 BNEZC and JIALC instructions")
Cc: stable <stable@vger.kernel.org> # v4.0+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16178/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull networking fixes from David Miller:
1) The netlink attribute passed in to dev_set_alias() is not
necessarily NULL terminated, don't use strlcpy() on it. From
Alexander Potapenko.
2) Fix implementation of atomics in arm64 bpf JIT, from Daniel
Borkmann.
3) Correct the release of netdevs and driver private data in certain
circumstances.
4) Sanitize netlink message length properly in decnet, from Mateusz
Jurczyk.
5) Don't leak kernel data in rtnl_fill_vfinfo() netlink blobs. From
Yuval Mintz.
6) Hash secret is never initialized in ipv6 ILA translation code, from
Arnd Bergmann. I guess those clang warnings about unused inline
functions are useful for something!
7) Fix endian selection in bpf_endian.h, from Daniel Borkmann.
8) Sanitize sockaddr length before dereferncing any fields in AF_UNIX
and CAIF. From Mateusz Jurczyk.
9) Fix timestamping for GMAC3 chips in stmmac driver, from Mario
Molitor.
10) Do not leak netdev on dev_alloc_name() errors in mac80211, from
Johannes Berg.
11) Fix locking in sctp_for_each_endpoint(), from Xin Long.
12) Fix wrong memset size on 32-bit in snmp6, from Christian Perle.
13) Fix use after free in ip_mc_clear_src(), from WANG Cong.
14) Fix regressions caused by ICMP rate limiting changes in 4.11, from
Jesper Dangaard Brouer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (91 commits)
i40e: Fix a sleep-in-atomic bug
net: don't global ICMP rate limit packets originating from loopback
net/act_pedit: fix an error code
net: update undefined ->ndo_change_mtu() comment
net_sched: move tcf_lock down after gen_replace_estimator()
caif: Add sockaddr length check before accessing sa_family in connect handler
qed: fix dump of context data
qmi_wwan: new Telewell and Sierra device IDs
net: phy: Fix MDIO_THUNDER dependencies
netconsole: Remove duplicate "netconsole: " logging prefix
igmp: acquire pmc lock for ip_mc_clear_src()
r8152: give the device version
net: rps: fix uninitialized symbol warning
mac80211: don't send SMPS action frame in AP mode when not needed
mac80211/wpa: use constant time memory comparison for MACs
mac80211: set bss_info data before configuring the channel
mac80211: remove 5/10 MHz rate code from station MLME
mac80211: Fix incorrect condition when checking rx timestamp
mac80211: don't look at the PM bit of BAR frames
i40e: fix handling of HW ATR eviction
...
Pull crypto fix from Herbert Xu:
"This fixes a bug on sparc where we may dereference freed stack memory"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: Work around deallocated stack frame reference gcc bug on sparc.
- Revert a 4.11 ACPICA change that made assumptions which are not
satisfied on some systems and caused the enumeration of resources
to fail on them (Rafael Wysocki).
- Add a mechanism to prevent tables from being unmapped prematurely
due to reference counter overflows (Lv Zheng).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Rk+Z
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These revert an ACPICA commit from the 4.11 cycle that causes problems
to happen on some systems and add a protection against possible kernel
crashes due to table reference counter imbalance.
Specifics:
- Revert a 4.11 ACPICA change that made assumptions which are not
satisfied on some systems and caused the enumeration of resources
to fail on them (Rafael Wysocki).
- Add a mechanism to prevent tables from being unmapped prematurely
due to reference counter overflows (Lv Zheng)"
* tag 'acpi-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: Tables: Mechanism to handle late stage acpi_get_table() imbalance
Revert "ACPICA: Disassembler: Enhance resource descriptor detection"
- Revert a recent cpufreq schedutil governor change that caused some
systems to behave undesirably (Rafael Wysocki).
- Fix a cpufreq conservative governor issue introduced during the
3.10 cycle that prevents it from working as expected in some
situations (Tomasz Wilczyński).
- Fix an error code path in the generic cpuidle driver for DT-based
systems (Christophe Jaillet).
- Fix three minor issues in devfreq drivers for Exynos (Arvind Yadav,
Krzysztof Kozlowski).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=R3HI
-----END PGP SIGNATURE-----
Merge tag 'pm-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These revert a recent cpufreq schedutil governor change that turned
out to be problematic and fix a few minor issues in cpufreq, cpuidle
and the Exynos devfreq drivers.
Specifics:
- Revert a recent cpufreq schedutil governor change that caused some
systems to behave undesirably (Rafael Wysocki).
- Fix a cpufreq conservative governor issue introduced during the
3.10 cycle that prevents it from working as expected in some
situations (Tomasz Wilczyński).
- Fix an error code path in the generic cpuidle driver for DT-based
systems (Christophe Jaillet).
- Fix three minor issues in devfreq drivers for Exynos (Arvind Yadav,
Krzysztof Kozlowski)"
* tag 'pm-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: dt: Add missing 'of_node_put()'
cpufreq: conservative: Allow down_threshold to take values from 1 to 10
Revert "cpufreq: schedutil: Reduce frequencies slower"
PM / devfreq: exynos-ppmu: Staticize event list
PM / devfreq: exynos-ppmu: Handle return value of clk_prepare_enable
PM / devfreq: exynos-nocp: Handle return value of clk_prepare_enable
Pull HID fix from Jiri Kosina:
- ifdef-based bandaid for a long-standing issue with HID driver
matching, avoiding regressions in cases where specific driver is not
enabled in kernel .config, from Jiri Kosina
* 'for-4.12/driver-matching-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: let generic driver yield control iff specific driver has been enabled
-----BEGIN PGP SIGNATURE-----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=GEtG
-----END PGP SIGNATURE-----
Merge tag 'media/v4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- some build dependency issues at CEC core with randconfigs
- fix an off by one error at vb2
- a race fix at cec core
- driver fixes at tc358743, sir_ir and rainshadow-cec
* tag 'media/v4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] media/cec.h: use IS_REACHABLE instead of IS_ENABLED
[media] cec: race fix: don't return -ENONET in cec_receive()
[media] sir_ir: infinite loop in interrupt handler
[media] cec-notifier.h: handle unreachable CONFIG_CEC_CORE
[media] cec: improve MEDIA_CEC_RC dependencies
[media] vb2: Fix an off by one error in 'vb2_plane_vaddr'
[media] rainshadow-cec: Fix missing spin_lock_init()
[media] tc358743: fix register i2c_rd/wr function fix
The logics when deciding whether we need to do anything with direct blocks
is broken when new size is within the last direct block. It's better to
find the path to the last byte _not_ to be removed and use that instead
of the path to the beginning of the first block to be freed...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
tail unpacking is done in a wrong place; the deadlocks galore
is best dealt with by doing that in ->write_iter() (and switching
to iomap, while we are at it), but that's rather painful to
backport. The trouble comes from grabbing pages that cover
the beginning of tail from inside of ufs_new_fragments(); ongoing
pageout of any of those is going to deadlock on ->truncate_mutex
with process that got around to extending the tail holding that
and waiting for page to get unlocked, while ->writepage() on
that page is waiting on ->truncate_mutex.
The thing is, we don't need ->truncate_mutex when the fragment
we are trying to map is within the tail - the damn thing is
allocated (tail can't contain holes).
Let's do a plain lookup and if the fragment is present, we can
just pretend that we'd won the race in almost all cases. The
only exception is a fragment between the end of tail and the
end of block containing tail.
Protect ->i_lastfrag with ->meta_lock - read_seqlock_excl() is
sufficient.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The driver may sleep under a spin lock, and the function call path is:
i40e_ndo_set_vf_port_vlan (acquire the lock by spin_lock_bh)
i40e_vsi_remove_pvid
i40e_vlan_stripping_disable
i40e_aq_update_vsi_params
i40e_asq_send_command
mutex_lock --> may sleep
To fixed it, the spin lock is released before "i40e_vsi_remove_pvid", and
the lock is acquired again after this function.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
callers rely upon that, but find_lock_page() racing with attempt of
page eviction by memory pressure might have left us with
* try_to_free_buffers() successfully done
* __remove_mapping() failed, leaving the page in our mapping
* find_lock_page() returning an uptodate page with no
buffer_heads attached.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
For UFS2 we need 64bit variants; we even store them in uspi, but
use 32bit ones instead. One wrinkle is in handling of reserved
space - recalculating it every time had been stupid all along, but
now it would become really ugly. Just calculate it once...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
a) honour ->s_minfree; don't just go with default (5)
b) don't bother with capability checks until we know we'll need them
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Florian Weimer seems to have a glibc test-case which requires that
loopback interfaces does not get ICMP ratelimited. This was broken by
commit c0303efeab ("net: reduce cycles spend on ICMP replies that
gets rate limited").
An ICMP response will usually be routed back-out the same incoming
interface. Thus, take advantage of this and skip global ICMP
ratelimit when the incoming device is loopback. In the unlikely event
that the outgoing it not loopback, due to strange routing policy
rules, ICMP rate limiting still works via peer ratelimiting via
icmpv4_xrlim_allow(). Thus, we should still comply with RFC1812
(section 4.3.2.8 "Rate Limiting").
This seems to fix the reproducer given by Florian. While still
avoiding to perform expensive and unneeded outgoing route lookup for
rate limited packets (in the non-loopback case).
Fixes: c0303efeab ("net: reduce cycles spend on ICMP replies that gets rate limited")
Reported-by: Florian Weimer <fweimer@redhat.com>
Reported-by: "H.J. Lu" <hjl.tools@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid that the following complaint is reported:
BUG: sleeping function called from invalid context at kernel/workqueue.c:2790
in_atomic(): 1, irqs_disabled(): 0, pid: 41, name: rcuop/3
1 lock held by rcuop/3/41:
#0: (rcu_callback){......}, at: [<ffffffff8111f9a2>] rcu_nocb_kthread+0x282/0x500
Call Trace:
dump_stack+0x86/0xcf
___might_sleep+0x174/0x260
__might_sleep+0x4a/0x80
flush_work+0x7e/0x2e0
__cancel_work_timer+0x143/0x1c0
cancel_work_sync+0x10/0x20
blk_throtl_exit+0x25/0x60
blkcg_exit_queue+0x35/0x40
blk_release_queue+0x42/0x130
kobject_put+0xa9/0x190
This happens since we invoke callbacks that need to block from the
queue release handler. Fix this by pushing the final release to
a workqueue.
Reported-by: Ross Zwisler <zwisler@gmail.com>
Fixes: commit b425e50492 ("block: Avoid that blk_exit_rl() triggers a use-after-free")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Tested-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Updated changelog
Signed-off-by: Jens Axboe <axboe@fb.com>
I'm reviewing static checker warnings where we do ERR_PTR(0), which is
the same as NULL. I'm pretty sure we intended to return ERR_PTR(-EINVAL)
here. Sometimes these bugs lead to a NULL dereference but I don't
immediately see that problem here.
Fixes: 71d0ed7079 ("net/act_pedit: Support using offset relative to the conventional network headers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Amir Vadai <amir@vadai.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Storing stats _only_ at new locations is wrong for UFS1; old
locations should always be kept updated. The check for "has
been converted to use of new locations" is also wrong - it
should be "->fs_maxbsize is equal to ->fs_bsize".
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The flow of creating a new child goes through ipoib_vlan_add
which allocates a new interface and checks the rtnl_lock.
If the lock is taken, restart_syscall will be called to restart
the system call again. In this case we are not releasing the
already allocated interface, causing a leak.
Fixes: 9baa0b0364 ("IB/ipoib: Add rtnl_link_ops support")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch mekas init_default and uninit_default symmetric
with a call to delete napi. Additionally, the uninit_default
gained delete napi call in case of init_default fails.
Fixes: 515ed4f3aa ('IB/IPoIB: Separate control and data related initializations')
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is a need to free priv explicitly and not just to release
the device, child priv is freed explicitly on remove flow and this
patch also includes priv free on error flow in P_key creation
and also in add_port.
Fixes: cd565b4b51 ('IB/IPoIB: Support acceleration options callbacks')
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Update ->ndo_change_mtu() callback comment to remove text
about returning error in case of undefined callback. This
change makes the comment match the existing code behavior.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit: 0a943cb10c (tools build: Add HOSTARCH Makefile variable)
when building for ARCH=x86_64, ARCH=x86_64 is passed to perf instead of
ARCH=x86, so the perf build process searchs header files from
tools/arch/x86_64/include, which doesn't exist.
The following build failure is seen:
In file included from util/event.c:2:0:
tools/include/uapi/linux/mman.h:4:27: fatal error: uapi/asm/mman.h: No such file or directory
compilation terminated.
Fix this issue by using SRCARCH instead of ARCH in perf, just like the
main kernel Makefile and tools/objtool's.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>
Cc: Jan Stancek <jstancek@redhat.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Rui Teng <rui.teng@linux.vnet.ibm.com>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: Wang Nan <wangnan0@huawei.com>
Fixes: 0a943cb10c ("tools build: Add HOSTARCH Makefile variable")
Link: http://lkml.kernel.org/r/1491793357-14977-2-git-send-email-jiada_wang@mentor.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Since commit 18e7a45af9 ("perf/x86: Reject non sampling events with
precise_ip") returns -EINVAL for sys_perf_event_open() with an attribute
with (attr.precise_ip > 0 && attr.sample_period == 0), just like is done
in the routine used to probe the max precise level when no events were
passed to 'perf record' or 'perf top', i.e.:
perf_evsel__new_cycles()
perf_event_attr__set_max_precise_ip()
The x86 code, in x86_pmu_hw_config(), which is called all the way from
sys_perf_event_open() did, starting with the aforementioned commit:
/* There's no sense in having PEBS for non sampling events: */
if (!is_sampling_event(event))
return -EINVAL;
Which makes it fail for cycles:ppp, cycles:pp and cycles:p, always using
just the non precise cycles variant.
To make sure that this is the case, I tested it, before this patch,
with:
# perf probe -L x86_pmu_hw_config
<x86_pmu_hw_config@/home/acme/git/linux/arch/x86/events/core.c:0>
0 int x86_pmu_hw_config(struct perf_event *event)
1 {
2 if (event->attr.precise_ip) {
<SNIP>
17 if (event->attr.precise_ip > precise)
18 return -EOPNOTSUPP;
/* There's no sense in having PEBS for non sampling events: */
21 if (!is_sampling_event(event))
22 return -EINVAL;
}
<SNIP>
# perf probe x86_pmu_hw_config:22
Added new events:
probe:x86_pmu_hw_config (on x86_pmu_hw_config:22)
probe:x86_pmu_hw_config_1 (on x86_pmu_hw_config:22)
You can now use it in all perf tools, such as:
perf record -e probe:x86_pmu_hw_config_1 -aR sleep 1
# perf trace -e perf_event_open,probe:x86_pmu_hwconfig*/max-stack=16/ perf record usleep 1
0.000 ( 0.015 ms): perf/4150 perf_event_open(attr_uptr: 0x7ffebc8ba110, cpu: -1, group_fd: -1 ) ...
0.015 ( ): probe:x86_pmu_hw_config:(ffffffff9c0065e1))
x86_pmu_hw_config ([kernel.kallsyms])
hsw_hw_config ([kernel.kallsyms])
x86_pmu_event_init ([kernel.kallsyms])
perf_try_init_event ([kernel.kallsyms])
perf_event_alloc ([kernel.kallsyms])
SYSC_perf_event_open ([kernel.kallsyms])
sys_perf_event_open ([kernel.kallsyms])
do_syscall_64 ([kernel.kallsyms])
return_from_SYSCALL_64 ([kernel.kallsyms])
syscall (/usr/lib64/libc-2.24.so)
perf_event_attr__set_max_precise_ip (/home/acme/bin/perf)
perf_evsel__new_cycles (/home/acme/bin/perf)
perf_evlist__add_default (/home/acme/bin/perf)
cmd_record (/home/acme/bin/perf)
run_builtin (/home/acme/bin/perf)
handle_internal_command (/home/acme/bin/perf)
0.000 ( 0.021 ms): perf/4150 ... [continued]: perf_event_open()) = -1 EINVAL Invalid argument
0.023 ( 0.002 ms): perf/4150 perf_event_open(attr_uptr: 0x7ffebc8ba110, cpu: -1, group_fd: -1 ) ...
0.025 ( ): probe:x86_pmu_hw_config:(ffffffff9c0065e1))
x86_pmu_hw_config ([kernel.kallsyms])
hsw_hw_config ([kernel.kallsyms])
x86_pmu_event_init ([kernel.kallsyms])
perf_try_init_event ([kernel.kallsyms])
perf_event_alloc ([kernel.kallsyms])
SYSC_perf_event_open ([kernel.kallsyms])
sys_perf_event_open ([kernel.kallsyms])
do_syscall_64 ([kernel.kallsyms])
return_from_SYSCALL_64 ([kernel.kallsyms])
syscall (/usr/lib64/libc-2.24.so)
perf_event_attr__set_max_precise_ip (/home/acme/bin/perf)
perf_evsel__new_cycles (/home/acme/bin/perf)
perf_evlist__add_default (/home/acme/bin/perf)
cmd_record (/home/acme/bin/perf)
run_builtin (/home/acme/bin/perf)
handle_internal_command (/home/acme/bin/perf)
0.023 ( 0.004 ms): perf/4150 ... [continued]: perf_event_open()) = -1 EINVAL Invalid argument
0.028 ( 0.002 ms): perf/4150 perf_event_open(attr_uptr: 0x7ffebc8ba110, cpu: -1, group_fd: -1 ) ...
0.030 ( ): probe:x86_pmu_hw_config:(ffffffff9c0065e1))
x86_pmu_hw_config ([kernel.kallsyms])
hsw_hw_config ([kernel.kallsyms])
x86_pmu_event_init ([kernel.kallsyms])
perf_try_init_event ([kernel.kallsyms])
perf_event_alloc ([kernel.kallsyms])
SYSC_perf_event_open ([kernel.kallsyms])
sys_perf_event_open ([kernel.kallsyms])
do_syscall_64 ([kernel.kallsyms])
return_from_SYSCALL_64 ([kernel.kallsyms])
syscall (/usr/lib64/libc-2.24.so)
perf_event_attr__set_max_precise_ip (/home/acme/bin/perf)
perf_evsel__new_cycles (/home/acme/bin/perf)
perf_evlist__add_default (/home/acme/bin/perf)
cmd_record (/home/acme/bin/perf)
run_builtin (/home/acme/bin/perf)
handle_internal_command (/home/acme/bin/perf)
0.028 ( 0.004 ms): perf/4150 ... [continued]: perf_event_open()) = -1 EINVAL Invalid argument
41.018 ( 0.012 ms): perf/4150 perf_event_open(attr_uptr: 0x7ffebc8b5dd0, pid: -1, group_fd: -1, flags: FD_CLOEXEC) = 4
41.065 ( 0.011 ms): perf/4150 perf_event_open(attr_uptr: 0x3c7db78, pid: -1, group_fd: -1, flags: FD_CLOEXEC) = 4
41.080 ( 0.006 ms): perf/4150 perf_event_open(attr_uptr: 0x3c7db78, pid: -1, group_fd: -1, flags: FD_CLOEXEC) = 4
41.103 ( 0.010 ms): perf/4150 perf_event_open(attr_uptr: 0x3c4e748, pid: 4151 (perf), group_fd: -1, flags: FD_CLOEXEC) = 4
41.115 ( 0.006 ms): perf/4150 perf_event_open(attr_uptr: 0x3c4e748, pid: 4151 (perf), cpu: 1, group_fd: -1, flags: FD_CLOEXEC) = 5
41.122 ( 0.004 ms): perf/4150 perf_event_open(attr_uptr: 0x3c4e748, pid: 4151 (perf), cpu: 2, group_fd: -1, flags: FD_CLOEXEC) = 6
41.128 ( 0.008 ms): perf/4150 perf_event_open(attr_uptr: 0x3c4e748, pid: 4151 (perf), cpu: 3, group_fd: -1, flags: FD_CLOEXEC) = 8
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.017 MB perf.data (2 samples) ]
#
I.e. that return -EINVAL in x86_pmu_hw_config() is hit three times.
So fix it by just setting attr.sample_period
Now, after this patch:
# perf trace --max-stack=2 -e perf_event_open,probe:x86_pmu_hw_config* perf record usleep 1
[ perf record: Woken up 1 times to write data ]
0.000 ( 0.017 ms): perf/8469 perf_event_open(attr_uptr: 0x7ffe36c27d10, pid: -1, cpu: 3, group_fd: -1, flags: FD_CLOEXEC) = 4
syscall (/usr/lib64/libc-2.24.so)
perf_event_open_cloexec_flag (/home/acme/bin/perf)
0.050 ( 0.031 ms): perf/8469 perf_event_open(attr_uptr: 0x24ebb78, pid: -1, group_fd: -1, flags: FD_CLOEXEC) = 4
syscall (/usr/lib64/libc-2.24.so)
perf_evlist__config (/home/acme/bin/perf)
0.092 ( 0.040 ms): perf/8469 perf_event_open(attr_uptr: 0x24ebb78, pid: -1, group_fd: -1, flags: FD_CLOEXEC) = 4
syscall (/usr/lib64/libc-2.24.so)
perf_evlist__config (/home/acme/bin/perf)
0.143 ( 0.007 ms): perf/8469 perf_event_open(attr_uptr: 0x24bc748, cpu: -1, group_fd: -1 ) = 4
syscall (/usr/lib64/libc-2.24.so)
perf_event_attr__set_max_precise_ip (/home/acme/bin/perf)
0.161 ( 0.007 ms): perf/8469 perf_event_open(attr_uptr: 0x24bc748, pid: 8470 (perf), group_fd: -1, flags: FD_CLOEXEC) = 4
syscall (/usr/lib64/libc-2.24.so)
perf_evsel__open (/home/acme/bin/perf)
0.171 ( 0.005 ms): perf/8469 perf_event_open(attr_uptr: 0x24bc748, pid: 8470 (perf), cpu: 1, group_fd: -1, flags: FD_CLOEXEC) = 5
syscall (/usr/lib64/libc-2.24.so)
perf_evsel__open (/home/acme/bin/perf)
0.180 ( 0.007 ms): perf/8469 perf_event_open(attr_uptr: 0x24bc748, pid: 8470 (perf), cpu: 2, group_fd: -1, flags: FD_CLOEXEC) = 6
syscall (/usr/lib64/libc-2.24.so)
perf_evsel__open (/home/acme/bin/perf)
0.190 ( 0.005 ms): perf/8469 perf_event_open(attr_uptr: 0x24bc748, pid: 8470 (perf), cpu: 3, group_fd: -1, flags: FD_CLOEXEC) = 8
syscall (/usr/lib64/libc-2.24.so)
perf_evsel__open (/home/acme/bin/perf)
[ perf record: Captured and wrote 0.017 MB perf.data (7 samples) ]
#
The probe one called from perf_event_attr__set_max_precise_ip() works
the first time, with attr.precise_ip = 3, wit hthe next ones being the
per cpu ones for the cycles:ppp event.
And here is the text from a report and alternative proposed patch by
Thomas-Mich Richter:
---
On s390 the counter and sampling facility do not support a precise IP
skid level and sometimes returns EOPNOTSUPP when structure member
precise_ip in struct perf_event_attr is not set to zero.
On s390 commnd 'perf record -- true' fails with error EOPNOTSUPP. This
happens only when no events are specified on command line.
The functions called are
...
--> perf_evlist__add_default
--> perf_evsel__new_cycles
--> perf_event_attr__set_max_precise_ip
The last function determines the value of structure member precise_ip by
invoking the perf_event_open() system call and checking the return code.
The first successful open is the value for precise_ip.
However the value is determined without setting member sample_period and
indicates no sampling.
On s390 the counter facility and sampling facility are different. The
above procedure determines a precise_ip value of 3 using the counter
facility. Later it uses the sampling facility with a value of 3 and
fails with EOPNOTSUPP.
---
v2: Older compilers (e.g. gcc 4.4.7) don't support referencing members
of unnamed union members in the container struct initialization, so
move from:
struct perf_event_attr attr = {
...
.sample_period = 1,
};
to right after it as:
struct perf_event_attr attr = {
...
};
attr.sample_period = 1;
v3: We need to reset .sample_period to 0 to let the users of
perf_evsel__new_cycles() to properly setup attr.sample_period or
attr.sample_freq. Reported by Ingo Molnar.
Reported-and-Acked-by: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com>
Acked-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Fixes: 18e7a45af9 ("perf/x86: Reject non sampling events with precise_ip")
Link: http://lkml.kernel.org/n/tip-yv6nnkl7tzqocrm0hl3x7vf1@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Laura reported a sleep-in-atomic kernel warning inside
tcf_act_police_init() which calls gen_replace_estimator() with
spinlock protection.
It is not necessary in this case, we already have RTNL lock here
so it is enough to protect concurrent writers. For the reader,
i.e. tcf_act_police(), it needs to make decision based on this
rate estimator, in the worst case we drop more/less packets than
necessary while changing the rate in parallel, it is still acceptable.
Reported-by: Laura Abbott <labbott@redhat.com>
Reported-by: Nick Huber <nicholashuber@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current __ceph_setattr() can set inode's i_ctime to current_time(),
req->r_stamp or attr->ia_ctime. These time stamps may have minor
differences. It may cause potential problem.
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
ceph uses ktime_get_real_ts() to get request time stamp. In most
other cases, current_kernel_time() is used to get time stamp for
filesystem operations (called by current_time()).
There is granularity difference between ktime_get_real_ts() and
current_kernel_time(). The later one can be up to one jiffy behind
the former one. This can causes inode's ctime to go back.
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Converting a file handle to a dentry can be done call after the inode
unlink. This means that __fh_to_dentry() requires an extra check to
verify the number of links is not 0.
The issue can be easily reproduced using xfstest generic/426, which does
something like:
name_to_handle_at(&fh)
echo 3 > /proc/sys/vm/drop_caches
unlink()
open_by_handle_at(&fh)
The call to open_by_handle_at() should fail, as the file doesn't exist
anymore.
Link: http://tracker.ceph.com/issues/19958
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The driver may sleep under a spin lock, and the function call path is:
post_one_send (acquire the lock by spin_lock_irqsave)
init_send_wqe
copy_from_user --> may sleep
There is no flow that makes "qp->is_user" true, and copy_from_user may
cause bug when a non-user pointer is used. So the lines of copy_from_user
and check of "qp->is_user" are removed.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add 64KB PAGE_SIZE support to user-space CQ, SQ and RQ queues.
De-facto it means that code was added to translate 64KB
pages to smaller 4KB pages that the FW can handle. Otherwise,
the FW would wrap (or jump to the next page) when reaching 4KB
while the user space library will continue on the same large page.
Note that MR code remains as is since the FW supports larger pages
for MRs.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
