* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (83 commits)
mmc: fix compile error when CONFIG_BLOCK is not enabled
mmc: core: Cleanup eMMC4.5 conditionals
mmc: omap_hsmmc: if multiblock reads are broken, disable them
mmc: core: add workaround for controllers with broken multiblock reads
mmc: core: Prevent too long response times for suspend
mmc: recognise SDIO cards with SDIO_CCCR_REV 3.00
mmc: sd: Handle SD3.0 cards not supporting UHS-I bus speed mode
mmc: core: support HPI send command
mmc: core: Add cache control for eMMC4.5 device
mmc: core: Modify the timeout value for writing power class
mmc: core: new discard feature support at eMMC v4.5
mmc: core: mmc sanitize feature support for v4.5
mmc: dw_mmc: modify DATA register offset
mmc: sdhci-pci: add flag for devices that can support runtime PM
mmc: omap_hsmmc: ensure pbias configuration is always done
mmc: core: Add Power Off Notify Feature eMMC 4.5
mmc: sdhci-s3c: fix potential NULL dereference
mmc: replace printk with appropriate display macro
mmc: core: Add default timeout value for CMD6
mmc: sdhci-pci: add runtime pm support
...
All the files using printk function for displaying kernel messages
in the mmc driver have been replaced with corresponding macro.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The error condition indicates that mmci_post_request() should cleanup
after the mmci_pre_request(). In this case the resources allocated by
device_prep_slave_sg() are freed by calling dmaengine_terminate_all().
dma_unmap_sg() should always be performed if the host_cookie is set.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add runtime PM support to the MMCI primecell driver, making use of
the core primecell bus runtime PM support.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits)
ARM: 7004/1: fix traps.h compile warnings
ARM: 6998/2: kernel: use proper memory barriers for bitops
ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM
ARM: Fix build errors caused by adding generic macros
ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU
ARM: CPU hotplug: pass in proper affinity mask on IRQ migration
ARM: GIC: avoid routing interrupts to offline CPUs
ARM: CPU hotplug: fix abuse of irqdesc->node
ARM: 6981/2: mmci: adjust calculation of f_min
ARM: 7000/1: LPAE: Use long long printk format for displaying the pud
ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state
ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence
ARM: ARM_DMA_ZONE_SIZE is no more
ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
...
pre_req() runs dma_map_sg() and prepares the dma descriptor for the next
mmc data transfer. post_req() runs dma_unmap_sg. If not calling pre_req()
before mmci_request(), mmci_request() will prepare the cache and dma just
like it did it before. It is optional to use pre_req() and post_req()
for mmci.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The ARM version maximum clock divider is 512 whereas for the ST
variants it's 257. Let's use DIV_ROUND_UP() for both cases so we
can see clearly what's going on here.
[Use DIV_ROUND_UP to clarify elder code]
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Stresstesting insert/remove of SD-cards can trigger
a StartBitErr. This made the driver to hang in forever
waiting for a non ocurring data timeout.
This bit and interrupt is documented in the original
PL180 TRM, just never implemented until now.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Right now the card detect IRQ for MMCI is requested without any
flags which will give some default machine-specified IRQ
behaviour. However on the U300 rising+falling edges (such as can
be expected from a simple GPIO to generate when inserting/removing
a card) need to be requested explicitly.
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Ulf Hansson <ulf.hansson@stericsson.com>
Cc: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ST-Ericsson modified ARM PrimeCell PL180 block has not got
an updated corresponding amba-id, althought the IP block has
changed in db8500v2. The change was done to the datactrl register.
Using the overrided subversion ID, account for this.
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes a regression on high clock speeds with the MMCI on
ux500. We need to make sure we derive the passthru clock on the
falling edge of the incoming clock if it shall work at high
frequencies, and on the ux500's there is a special bit for this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mmci.h header contained a few registers not clearly marked
as ST Micro only, rectify this and remove the HWFC magic in the
process. The idea is to make the mmci.h header file more ordered
so other vendors with PL180 derivates can see where to put in
their custom register defines.
Includes portions of an earlier patch from Sebastian Rasmussen.
Acked-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
New IO FPGA implementation for Versatile Express boards contain
MMCI (PL180) cell with FIFO extended to 128 words (512 bytes).
Matt Waddel reports that this patch improves MMC performance on
his vexpress system, and also fixes "mmcblk0: error -5 transferring
data" errors.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Tested-by: Matt Waddel <matt.waddel@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Based on a patch from Linus Walleij.
Add dmaengine based support for DMA to the MMCI driver, using the
Primecell DMA engine interface. The changes over Linus' driver are:
- rename txsize_threshold to dmasize_threshold, as this reflects the
purpose more.
- use 'mmci_dma_' as the function prefix rather than 'dma_mmci_'.
- clean up requesting of dma channels.
- don't release a single channel twice when it's shared between tx and rx.
- get rid of 'dma_enable' bool - instead check whether the channel is NULL.
- detect incomplete DMA at the end of a transfer. Some DMA controllers
(eg, PL08x) are unable to be configured for scatter DMA and also listen
to all four DMA request signals [BREQ,SREQ,LBREQ,LSREQ] from the MMCI.
They can do one or other but not both. As MMCI uses LBREQ/LSREQ for the
final burst/words, PL08x does not transfer the last few words.
- map and unmap DMA buffers using the DMA engine struct device, not the
MMCI struct device - the DMA engine is doing the DMA transfer, not us.
- avoid double-unmapping of the DMA buffers on MMCI data errors.
- don't check for negative values from the dmaengine tx submission
function - Dan says this must never fail.
- use new dmaengine helper functions rather than using the ugly function
pointers directly.
- allow DMA code to be fully optimized away using dma_inprogress() which
is defined to constant 0 if DMA engine support is disabled.
- request maximum segment size from the DMA engine struct device and
set this appropriately.
- removed checking of buffer alignment - the DMA engine should deal with
its own restrictions on buffer alignment, not the individual DMA engine
users.
- removed setting DMAREQCTL - this confuses some DMA controllers as it
causes LBREQ to be asserted for the last seven transfers, rather than
six SREQ and one LSREQ.
- removed burst setting - the DMA controller should not burst past the
transfer size required to complete the DMA operation.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need to store the number of bytes transferred in our host
structure - we can store this directly in data->bytes_xfered.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need to switch to data available interrupts if there's at
least half a FIFO depth worth of data remaining, as we'll still get
the FIFO half full interrupt. Keep this interrupt masked off until
we have less than half the FIFO depth worth of data remaining.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sg_miter API provides the required cache maintainence, so we don't
need to do that ourselves. Remove the unnecessary additional cache
maintainence.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The data counter counts the number of bytes transferred on the MMC bus.
When a FIFO overrun occurs, we will not have transferred a FIFOs-worth
of data to memory, and so the data counter will be a FIFOs-worth ahead.
If this occurs on a block boundary, we will report one too many sectors
as successful. Fix this.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We should not report incomplete blocks on error. Return the number of
bytes successfully transferred, rounded down to the nearest block.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When we encounter an error, make sure we complete the transaction
otherwise we'll leave the request dangling.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MMCIDATACNT register contain the number of byte left at error
not the number of words, so loose the << 2 thing. Further if CRC
fails on the first block, we may end up with a negative number
of transferred bytes which is not good, and the formula was in
wrong order.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Don't read the command response from the registers when either the
command timed out (because there was no response from the card) or
the checksum on the response was invalid.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <cjb@laptop.org>
Implement a suggestion from Russell to drop the use of blockend
interrupts altogether and instead rely on the data counter.
Tested with error-free cards on U300, U8500 and RealView PB1176.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make the MMCI announcement printk say which primecell part number
has been found. Display the revision as an unsigned decimal, and
display only the first 8 hex digits of the base address unless it's
larger.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I misread the datasheet as if bypass mode was not available at all
on the ux500's, I was wrong. It is there, the datasheet just
states that you should not have to use it.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Ux500 variant of this block has a different divider.
The value used right now is too big and which means a loss
in performance. This fix corrects it. Also expand the math
comments a bit so it's clear what's happening. Further
the Ux500 variant does not like if we use the BYPASS bit,
instead we are supposed to set the clock divider to zero.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds some minor variant data and trickery to enable SDIO
on the ST Micro variants of MMCI/PL180.
Signed-off-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On the U300 the MCI_DATAEND and MCI_DATABLOCKEND IRQs can arrive
out-of-order. Replace an ugly #ifdef hack with a proper runtime
solution which models what is really happening.
In the U300 DMA mode and on all Ux500 models, the MCI_DATABLOCKEND
flag isn't properly cleared in hardware following and ACK leading
to all kind of weird behaviour when the flag is still up in
subsequent interrupts, so we add two flags indicating the
error and handle this runtime.
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DBx500 variants have only one IRQ line hooked up. Allow these (and
any other implementations which choose to use only one irq) to work by
directing the PIO interrupts also to the first IRQ line.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After discovering a problem in regulator reference counting I took Mark
Brown's advice to move the reference count into the MMC core by making the
regulator status a member of struct mmc_host.
I took this opportunity to also implement NULL versions of
the regulator functions so as to rid the driver code from
some ugly #ifdef CONFIG_REGULATOR clauses.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Sundar Iyer <sundar.iyer@stericsson.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Cliff Brake <cbrake@bec-systems.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We have deprecated the distinction between hardware and physical
segments in the block layer. Consolidate the two limits into one in
drivers/mmc/.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently the kernel is screaming about slowpath at me for the
wp/cd callbacks. Switch to the _cansleep variants so as to silence
this.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The card may be always present on the board, and for these cases neither
a status callback nor a card detect GPIO is required, and card detection
polling can be disabled.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If an IRQ can be requested on the card detected GPIO, use it instead of
polling.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Ux500 variant has a 32-word FIFO (TXFIFOEMPTY is asserted when it
has 2 left) and TXFIFOHALFEMPTY is repurposed as TXFIFOBURSTWRITEABLE,
with a burst being defined as 8-words. Likewise for RX.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On some platforms, the GPIO value from the gpio_cd pin doesn't need to
be inverted to get it active high. Add a cd_invert platform data
parameter and change existing platforms using GPIO for CD (only
Realview) to enable it.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (291 commits)
ARM: AMBA: Add pclk support to AMBA bus infrastructure
ARM: 6278/2: fix regression in RealView after the introduction of pclk
ARM: 6277/1: mach-shmobile: Allow users to select HZ, default to 128
ARM: 6276/1: mach-shmobile: remove duplicate NR_IRQS_LEGACY
ARM: 6246/1: mmci: support larger MMCIDATALENGTH register
ARM: 6245/1: mmci: enable hardware flow control on Ux500 variants
ARM: 6244/1: mmci: add variant data and default MCICLOCK support
ARM: 6243/1: mmci: pass power_mode to the translate_vdd callback
ARM: 6274/1: add global control registers definition header file for nuc900
mx2_camera: fix type of dma buffer virtual address pointer
mx2_camera: Add soc_camera support for i.MX25/i.MX27
arm/imx/gpio: add spinlock protection
ARM: Add support for the LPC32XX arch
ARM: LPC32XX: Arch config menu supoport and makefiles
ARM: LPC32XX: Phytec 3250 platform support
ARM: LPC32XX: Misc support functions
ARM: LPC32XX: Serial support code
ARM: LPC32XX: System suspend support
ARM: LPC32XX: GPIO, timer, and IRQ drivers
ARM: LPC32XX: Clock driver
...
The MMC card detection sense has become really confused with negations
at various levels, leading to some platforms not detecting inserted
cards. Fix this by converting everything to positive logic throughout,
thereby getting rid of these negations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Ux500 variant has a 24-bit MMCIDATALENGTH register, as opposed to
the 16-bit one on the ARM version.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Although both the U300 and Ux500 use ST variants, the HWFCEN bits are at
different positions, so use the variant_data to store the information.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a variant_data structure to handle the differences between the
various variants of this peripheral. Add a first quirk for a default
MCICLOCK value, required on the Ux500 variant where the enable bit needs
to be always set, since it controls access to some registers.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Platforms may have some external power control which need to be
controlled from board specific code. Rename the translate_vdd()
callback to vdd_handler() and pass it the power mode.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the MMC core's ability to poll for card detection. This also has
the advantage of doing the gpio_get_value from a workqueue instead of
timer, allowing the gpio to be on a sleeping gpiochip.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the data transfer size to allow multi block transfers to work.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mmci driver's SG list iteration logic assumes that each SG entry
spans only one page, and only maps and flushes one page of the sg. This
is not a valid assumption. Fix it by converting the driver to the
sg_miter API, which correctly handles sgs which span multiple pages.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Even though many mmc host drivers pass a pm_message_t argument to
mmc_suspend_host() that argument isn't used the by MMC core. As host
drivers are converted to dev_pm_ops they'll have to construct
pm_message_t's (as they won't be passed by the PM subsystem any more) just
to appease the mmc suspend interface.
We might as well just delete the unused paramter.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>ZZ
Acked-by: Sascha Sommer <saschasommer@freenet.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
