Add Migo-R specific platform data for on-chip sh7722 CEU and ov772x camera.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clk_always_enable() on the sh7722 processor and in the board code
for Migo-R and Solution Engine 7722. Remove duplicate MSTPCR register
definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clk_always_enable() on the sh7723 processor and in the ap325rxa
board code. Remove duplicate MSTPCR register definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds initial support for the Renesas R0P7785LC0011RL board.
This patch supports 29bit address mode only.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables I2C on the sh7723-based ap325rxa board.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds basic support for the SH7763RDP board.
This supports a basic stuff provided in SH7763, like SCIF,
NOR Flash and USB host.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This board is SH7723 base board.
This has SCIF, LCDC, USB Host controler, NOR/NAND Flash, Sound,
Ether and other.
This patch supports SCIF, NOR Flash.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
IRQ trigger type can be specified in the IRQ resource definition by
IORESOURCE_IRQ_*, we need only one way to specify this.
This also fixes the following small issue:
To allow dynamic support for multiple platforms, when those relevant
macros are not defined for one specific platform, the default case
will be:
- SMC_DYNAMIC_BUS_CONFIG defined
- and SMC_IRQ_FLAGS = IRQF_TRIGGER_RISING
While if "irq_flags" is missing when defining the smc91x_platdata,
usually as follows:
static struct smc91x_platdata xxxx_smc91x_data = {
.flags = SMC91X_USE_XXBIT,
};
The lp->cfg.irq_flags will always be overriden by the above structure
(due to a memcpy), thus rendering lp->cfg.irq_flags to be "0" always.
(regardless of the default SMC_IRQ_FLAGS or IORESOURCE_IRQ_* flags)
Fixes this by forcing to use IORESOURCE_IRQ_* flags if present, and
make the only user of smc91x_platdata.irq_flags (renesas/migor) to
use IORESOURCE_IRQ_*.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make use of recently added sm501 8250 uart support, commit
61711f8fd8 makes the mfd code
handle 8250 uarts so there is no longer need to do it from
the r2d board code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Select smc91x bus width and irg flags using platform data for MigoR
now when the smc91x header file is in place.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Based on earlier work by Jon Smirl and Jochen Friedrich.
Update most new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. I've
left the video drivers apart (except for SoC camera drivers) as
they're a bit more diffcult to deal with, they'll have their own
patch later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Jochen Friedrich <jochen@scram.de>
Add support for the migor_ts touch panel to the MigoR board.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add NAND flash support to the MigoR board by giving board specific data
to the gen_nand platform driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add NOR flash support to the MigoR board by giving board specific data
to the physmap-flash platform driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use physical addresses and change resource name of MigoR ethernet chip.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds a MigoR specific header file. We may want to use a cpu
specific header file instead, but this will do for now.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add KEYSC platform data for the sh7722 MigoR board.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The only board-specific bits that existed here were for setting up the
IRQs, which are now handled by the SH7710 CPU support code instead. As
there's nothing else to do for setup, kill off the board support code
and have the defconfig use the generic machvec instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the highlander CF device from good old machvec readb/writeb
to the new shiny trapped io.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the CF device on r2d boards from machvec readb/writeb
to trapped io.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds basic support for the Migo-R board.
Only simple stuff provided by the cpu specific sh7722 code is in place now,
like serial console port, timers and usb gadget. There is also partial support
for the smc91c111 ethernet controller - unfortunately some driver header file
also needs patching (not included here) to make the driver get IRQ sense
information from the platform data.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds the header file asm/spi.h and board specific code for the
r2d board. The header file contains a structure that should be used to
point out a single spi bus. The board specific code for r2d is updated with
such a structure for the new spi_sh_sci driver. The structure contains a
chip select callback plus information about the R9701 rtc chip which is
attached to the spi bus.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the board specific irq code for r7780rp. The new code is
very similar to the other highlander implementations, with the exception that
the r7780rp handles pci interrupts using IRL. To simplify the pci code and
use the same interrupt numbers as r7780mp and r7785rp we hook in to the
cpu specific pci vectors.
The pci interrupts and the push switch all work well with and without this
patch. CF and AX88796 are not ok though and the source of the problem is
unknown at this point. The AX88796 does for not detect it's proper mac
address (IPL gets it right) and the kernel hangs on CF access. As a workaround
this patch removes the CF and the AX88796 from the platform datain case of
r7780rp.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for Renesas Technology Europe SDK7780 board.
Signed-off-by: Nicholas Beck <nbeck@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch tells the sm501 mfd driver to build platform data for the
sm501 usb host driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes redundant irq handling code together with unused
consistent alloc code. R2D uart setup code is changed to use
sm501-regs.h and unused header files are removed.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds timings to drive a Sharp LQ104V1DG21 lcd panel that can
be hooked up to R2D-1 or R2D-PLUS. The sm501fb driver should leave the
pins FPEN and VBIASEN alone, and this patch instructs the driver to do
so by not setting flags flags for these pins.
This patch works best together with the patch posted to the
linux-fbdev-devel list "sm501fb: control panel pin usage with platform
data flags", but this patch can be merged independently.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes interrupt priority tables from the intc code.
Optimal priority assignment varies with embedded application anyway,
so keeping the interrupt priority tables together with cpu-specific
code doesn't make sense.
The function intc_set_priority() should be used instead to set the
desired interrupt priority level.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes CF support for R2D-1 boards. Both R2D-1 and
R2D-PLUS are equipped with CF IRQs, but the R2D-1 FPGA version
seem to deliver IRQ spikes with certain CF cards during libata
probing. This patch enables polling for R2D-1 as a workaround
for this broken FGPA logic.
R2D-1 CF support was recently introduced by commit:
43f4b8c757.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
R7780RP can't do byte-sized accesses to CF, so needs to do word
sized access with low-byte masking. This same problem exists
on older versions of the R2D, with the same workaround having
been implemented in 43f4b8c757
there. Follow that change for the highlander boards.
This does not impact R7780MP or SH7785 based Highlander modules.
If you're unfortunate enough to be stuck with an R7780RP, this
patch is for you!
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the ax88796 driver on highlander boards.
Implemented using the 93cx6 EEPROM support introduced by commit-id
89e536a190.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables building for both R2D-PLUS and R2D-1 boards. All code is
already in place except for the Kconfig limitation. This is useful if you
want to run the same binary on both R2D-PLUS and R2D-1 boards.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
