* 'next/fixes' of git://git.linaro.org/people/arnd/arm-soc: (28 commits)
ARM: pxa/cm-x300: properly set bt_reset pin
ARM: mmp: rename SHEEVAD to GPLUGD
ARM: imx: Fix typo 'MACH_MX31_3DS_MXC_NAND_USE_BBT'
ARM: i.MX28: shift frac value in _CLK_SET_RATE
plat-mxc: iomux-v3.h: implicitly enable pull-up/down when that's desired
ARM: mx5: fix clock usage for suspend
ARM: pxa: use correct __iomem annotations
ARM: pxa: sharpsl pm needs SPI
ARM: pxa: centro and treo680 need palm27x
ARM: pxa: make pxafb_smart_*() empty when not enabled
ARM: pxa: select POWER_SUPPLY on raumfeld
ARM: pxa: pxa95x is incompatible with earlier pxa
ARM: pxa: CPU_FREQ_TABLE is needed for CPU_FREQ
ARM: pxa: pxa95x/saarb depends on pxa3xx code
ARM: pxa: allow selecting just one of TREO680/CENTRO
ARM: pxa: export symbols from pxa3xx-ulpi
ARM: pxa: make zylonite_pxa*_init declaration match code
ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer available
ARM: at91: add defconfig for at91sam9g45 family
ARM: at91: remove dependency for Atmel PWM driver selector in Kconfig
...
Noticed when setting SSP0 in clk_set_rate, _CLK_SET_RATE attempts to
reset the clock divider for the SSP0 parent clock, in this case
IO0FRAC. Bits 24-29 of HW_CLKCTRL_FRAC0 are cleared correctly, but
when the new frac value is written the value isn't shifted up to write
the correct bit-field. This results in IO0FRAC being set to 0 and
CPUFRAC being corrupted.
This should occur when writing IO1FRAC, EMIFRAC in HW_CLKCTRL_FRAC0
and GPMIFRAC, HSADCFRAC in HW_CLKCTRL_FRAC1.
Tested on custom i.MX28 board with SSP0 SPI driver.
Signed-off-by: Matt Burtch <matt@grid-net.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Boards used to specify zreladdr in their Makefile.boot with
zreladdr-y := x, so conflicting zreladdrs were silently overwritten.
This patch changes this to zreladdr-y += x, so that we end
up with multiple words in zreladdr in such a case. We can
detect this later and complain if necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some platforms (like OMAP not to name it) are doing rather complicated
hacks just to determine the base UART address to use. Let's give their
addruart macro some slack by providing an extra work register which will
allow for much needed cleanups.
This is basically a no-op as this commit is only adding the extra argument
to the macro but no one is using it yet.
Signed-off-by: nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Rather than marking the mach/gpio.h header files which want to use the
trivial GPIOLIB implementation, mark those which do not want to use it
instead. This means that by default, you get the trivial implementation
and only have to do something extra if you need to. This should
encourage the use of the trivial default implementation.
As an additional bonus, several gpio.h header files become empty.
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many of the gpio_to_irq implementations use the gpiolib version of this
function. Provide the standard gpiolib gpio_to_irq() for everyone, but
allow platforms to override it if they wish. Add the neccessary
overrides for those platforms which do not use the standard definition.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidate 24 trivial gpiolib implementions out of mach/gpio.h
into asm/gpio.h. This is basically the include of asm-generic/gpio.h
and the definition of gpio_get_value, gpio_set_value, and gpio_cansleep
as described in Documentation/gpio.txt
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: David Brown <davidb@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: Consolidate the clkdev header files
ARM: set vga memory base at run-time
ARM: convert PCI defines to variables
ARM: pci: make pcibios_assign_all_busses use pci_has_flag
ARM: remove unnecessary mach/hardware.h includes
pci: move microblaze and powerpc pci flag functions into asm-generic
powerpc: rename ppc_pci_*_flags to pci_*_flags
Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
* 'next/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (133 commits)
ARM: EXYNOS4: Change devname for FIMD clkdev
ARM: S3C64XX: Cleanup mach/regs-fb.h from mach-s3c64xx
ARM: S5PV210: Cleanup mach/regs-fb.h from mach-s5pv210
ARM: S5PC100: Cleanup mach/regs-fb.h from mach-s5pc100
ARM: S3C24XX: Use generic s3c_set_platdata for devices
ARM: S3C64XX: Use generic s3c_set_platdata for OneNAND
ARM: SAMSUNG: Use generic s3c_set_platdata for NAND
ARM: SAMSUNG: Use generic s3c_set_platdata for USB OHCI
ARM: SAMSUNG: Use generic s3c_set_platdata for HWMON
ARM: SAMSUNG: Use generic s3c_set_platdata for FB
ARM: SAMSUNG: Use generic s3c_set_platdata for TS
ARM: S3C64XX: Add PWM backlight support on SMDK6410
ARM: S5P64X0: Add PWM backlight support on SMDK6450
ARM: S5P64X0: Add PWM backlight support on SMDK6440
ARM: S5PC100: Add PWM backlight support on SMDKC100
ARM: S5PV210: Add PWM backlight support on SMDKV210
ARM: EXYNOS4: Add PWM backlight support on SMDKC210
ARM: EXYNOS4: Add PWM backlight support on SMDKV310
ARM: SAMSUNG: Create a common infrastructure for PWM backlight support
clocksource: convert 32-bit down counting clocksource on S5PV210/S5P64X0
...
Fix up trivial conflict in arch/arm/mach-imx/mach-scb9328.c
* 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (35 commits)
ARM: msm: platsmp: determine number of CPU cores at boot time
ARM: Tegra: Seaboard: Fix I2C bus numbering for ADT7461
ARM: Tegra: Trimslice: Tri-state DAP3 pinmux
ARM: orion5x: fixup 5181 MPP mask check
ARM: mxs-dma: include <linux/dmaengine.h>
ARM: i.MX53: consistently use MX53_UART_PAD_CTRL for uart txd/rxd/rts/cts
ARM: i.MX53: UARTn_CTS pin should not change RTS input select
ARM: i.MX53: UARTn_TXD pin should not change RXD input select
ARM: mx25: Fix typo on CAN1_RX pad setting
iomux-mx53: add missing 'IOMUX_CONFIG_SION' for some I2C pad definitions
ARM: NUC93X: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: LPC32XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: CNS3XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: i.MX53: Fix IOMUX type o's
ARM i.MX dma: Fix burstsize settings
mach-mx5: fix the I2C clock parents
ARM: mxs/tx28: according to the TX28's datasheet D4-D7 are not used for MMC0
ARM i.MX23/28: platform-mxsfb: Add missing include of linux/dma-mapping.h
ARM: mx53: Fix some interrupts marked as reserved.
MXC: iomux-v3: correct NO_PAD_CTRL definition
...
Fix up trivial conflict in arch/arm/mach-imx/mach-mx31_3ds.c
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6: (61 commits)
gpio/mxc/mxs: fix build error introduced by the irq_gc_ack() renaming
mcp23s08: add i2c support
mcp23s08: isolate spi specific parts
mcp23s08: get rid of setup/teardown callbacks
gpio/tegra: dt: add binding for gpio polarity
mcp23s08: remove unused work queue
gpio/da9052: remove a redundant assignment for gpio->da9052
gpio/mxc: add device tree probe support
ARM: mxc: use ARCH_NR_GPIOS to define gpio number
gpio/mxc: get rid of the uses of cpu_is_mx()
gpio/mxc: add missing initialization of basic_mmio_gpio shadow variables
gpio: Move mpc5200 gpio driver to drivers/gpio
GPIO: DA9052 GPIO module v3
gpio/tegra: Use engineering names in DT compatible property
of/gpio: Add new method for getting gpios under different property names
gpio/dt: Refine GPIO device tree binding
gpio/ml-ioh: fix off-by-one for displaying variable i in dev_err
gpio/pca953x: Deprecate meaningless device-tree bindings
gpio/pca953x: Remove dynamic platform data pointer
gpio/pca953x: Fix IRQ support.
...
Now most of ARM machines has the alsmot same __clk_get/put() macro
So place it at the arch/arm/include/asm/clkdev.h and remove the reduntant header files
But some machines don't have the same form as above. It can use the machince specific clkdev file by HAVE_MACH_CLKDEV config
Now there are only 3 caese.
1) define the clk structure with clkdev macro => Need to move clk structure to proper header file
arch/arm/mach-versatile/include/mach/clkdev.h
arch/arm/mach-realview/include/mach/clkdev.h
arch/arm/mach-vexpress/include/mach/clkdev.h
arch/arm/mach-integrator/include/mach/clkdev.h
2) export the __clk_get/put function at clock.c
arch/arm/mach-shmobile/include/mach/clkdev.h
3) demuxing the clk source
arch/arm/mach-u300/include/mach/clkdev.h
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Other files using dma.h may fail to compile as follows:
In file included from sound/soc/mxs/mxs-pcm.h:22,
from sound/soc/mxs/mxs-saif.h:112,
from sound/soc/mxs/mxs-sgtl5000.c:34:
arch/arm/mach-mxs/include/mach/dma.h:16: warning: 'struct dma_chan' declared inside parameter list
arch/arm/mach-mxs/include/mach/dma.h:16: warning: its scope is only this definition or declaration, which is probably not what you want
arch/arm/mach-mxs/include/mach/dma.h: In function 'mxs_dma_is_apbh':
arch/arm/mach-mxs/include/mach/dma.h:18: error: dereferencing pointer to incomplete type
arch/arm/mach-mxs/include/mach/dma.h: At top level:
arch/arm/mach-mxs/include/mach/dma.h:21: warning: 'struct dma_chan' declared inside parameter list
arch/arm/mach-mxs/include/mach/dma.h: In function 'mxs_dma_is_apbx':
arch/arm/mach-mxs/include/mach/dma.h:23: error: dereferencing pointer to incomplete type
make[3]: *** [sound/soc/mxs/mxs-sgtl5000.o] Error 1
make[2]: *** [sound/soc/mxs] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
It seems it's better for dma.h to include dmaengine.h himself.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It adds LED2 on mx28evk board as heartbeat trigger for diagnostic
purpose.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This allows to move the led definition to .init.rodata.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The pins are actually used (not in mainline yet):
D4 -> SSP2_D0
D5 -> GPIO
D6 -> GPIO
D7 -> GPIO for owire
so their pinmapping for SSP0 is wrong.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).
To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.
Hope people are OK with tiny include file.
Note, that mm_types.h is still dragged in, but it is a separate story.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch makes necessary changes on gpio-mxs as below to turn it
into an upstanding gpio driver.
* Clean up the gpio port definition stuff
* Use readl/writel to replace mach-specific accessors
__raw_readl/__raw_writel
* Change mxs_gpio_init into mxs_gpio_probe function
And it then migrates mach-mxs to the updated driver by adding
corresponding platform devices.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
GPIO drivers are getting moved to drivers/gpio for cleanup and
consolidation. This patch moves the mxs driver. Follow up patches
will clean it up and make it a fine upstanding example of a gpio
driver.
v2: Removed header file entirely and put struct definition directly
into driver. The struct isn't used anywhere else in the kernel.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
I get this build error as of today:
arch/arm/mach-mxs/ocotp.c: In function 'mxs_get_ocotp':
arch/arm/mach-mxs/ocotp.c:54: error: implicit declaration of function 'cpu_relax'
make[2]: *** [arch/arm/mach-mxs/ocotp.o] Error 1
Looks like it has been indirectly included before which broke now.
Include it directly.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Convert the MXS timrotv2 32-bit down counting clocksource to the
generic clocksource infrastructure.
Cc: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 47babe69 (mxs: dynamically allocate mmc device) added the ssp
setup and mmc clocks for mx23/28, but forgot to register the mmc clocks
on mx23.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For consistency mxs has to be repeated, one for the name space and
another one for the device name.
LAKML-Reference: 1300308028-8922-1-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The defines for the i2c related irqs (MX23_INT_I2C_DMA and
MX23_INT_I2C_ERROR) already match the reference manual. So make the base
address consistent.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
LAKML-Reference: 1298049507-6987-2-git-send-email-w.sang@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Current code does not set the GPIO value to zero as mentioned in the comment.
Fix it by setting the initial GPIO value to zero.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
LAKML-Reference: 1301427910-31726-1-git-send-email-fabio.estevam@freescale.com
[ukleinek: squashed two patches together fixing both boards at once]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To be able to relocate the .bss section at run time independently from
the rest of the code, we must make sure that no GOTOFF relocations are
used with .bss symbols. This usually means that no global variables can
be marked static unless they're also const.
Let's remove the static qualifier from current offenders, or turn them
into const variables when possible. Next commit will ensure the build
fails if one of those is reintroduced due to otherwise enforced coding
standards for the kernel.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
STMP378x and MX23 are the same and just relabeled. There is a
mach-stmp378x, however, it has a lot of reinvented interfaces, leaking
all sorts of mach-specific functions into the drivers. One example is
the dmaengine which does not use the linux dmaengine-API but some
privately exported symbols. This makes generic use of the drivers
impossible. mach-mxs does it better, so convert the board to mach-mxs.
After that, it is possible to delete all stmp-specific code which should
ease further ARM-consolidation.
Compile tested only due to no hardware (seems not available anymore).
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For the lcdif clock get_rate looks as follows:
read div from HW_CLKCTRL_DIS_LCDIF.DIV
return clk_get_rate(clk->parent) / div
with clk->parent being ref_pix_clk on my system.
ref_pix_clk's rate depends on HW_CLKCTRL_FRAC1.PIXFRAC.
The set_rate function for lcdif does:
parent_rate = clk_get_rate(clk->parent);
based on that calculate frac and div such that
parent_rate * 18 / frac / div is near the requested rate.
HW_CLKCTRL_FRAC1.PIXFRAC is updated with frac
HW_CLKCTRL_DIS_LCDIF.DIV is updated with div
For this calculation to be correct parent_rate needs to be
initialized not with the clock rate of lcdif's parent (i.e. ref_pix) but
that of its grandparent (i.e. ref_pix' parent == pll0_clk).
The obvious downside of this patch is that now set_rate(lcdif) changes
its parent's rate, too. Still this is better than a wrong rate.
Acked-by: Shawn Guo <shawn.guo@freescale.com>
LAKML-Reference: 20110225084950.GA13684@S2101-09.ap.freescale.net
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>