This patch converts the drivers in drivers/usb/gadget/* to use
module_pci_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: Xiaochen Shen <xiaochen.shen@intel.com>
Cc: Pavankumar Kondeti <pkondeti@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enabled the flag so that musb_dsps glue file can be used for am335x
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
TI81XX platform has two musb interfaces and uses CPPI4.1 DMA engine.
It has builtin USB PHYs as AM35x. The current set of patches adds support
for one instance and only in PIO mode.
[ balbi@ti.com : make it compile and solve a "may be used
uninitialized" warning ]
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
to avoid sprinkling magic constants on the driver
we define a constant to be used when allocating
setup_buffer and ep0_bounce buffer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use family rather than DCE check for clarity, also always use
wb on APUs, there will never be AGP variants.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
commit 61a0d80c "md/bitmap: discard CHUNK_BLOCK_SHIFT macro"
replaced CHUNK_BLOCK_RATIO() by the same text that was
replacing CHUNK_BLOCK_SHIFT() - which is clearly wrong.
The result is that 'chunks' is often too small by 1,
which can sometimes result in a crash (not sure how).
So use the correct replacement, and get rid of CHUNK_BLOCK_RATIO
which is no longe used.
Reported-by: Karl Newman <siliconfiend@gmail.com>
Tested-by: Karl Newman <siliconfiend@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YIOH
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull second set of MFD fixes from Samuel Ortiz:
"This time we only have a one liner fixing an omap-usb build error."
* tag 'mfd-for-linus-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Fix build breakage in omap-usb-host.c
Ben Hutchings pointed out that the validation in efivars was inadequate -
most obviously, an entry with size 0 would server as a DoS against the
kernel. Improve this based on his suggestions.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1) Fix regression that could cause a misdiagnosis, which in turn could
lead to an erroneous 3.0 Gbps -> 1.5 downshift, particularly when hotplug
and suspend/resume is involved.
2) Fix a regression that led to ata%d controller ids being numbered one
larger than in <= 3.4-rc3 (oh, the horror!). Controller ids should now be
as expected.
3) add some DT, PCI id's
4) ata/pata_arasan_cf: minor cpp fixing/cleaning
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c7fz
-----END PGP SIGNATURE-----
Merge tag 'tag/upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata fixes from Jeff Garzik:
1) Fix regression that could cause a misdiagnosis, which in turn could
lead to an erroneous 3.0 Gbps -> 1.5 downshift, particularly when hotplug
and suspend/resume is involved.
2) Fix a regression that led to ata%d controller ids being numbered one
larger than in <= 3.4-rc3 (oh, the horror!). Controller ids should now be
as expected.
3) add some DT, PCI id's
4) ata/pata_arasan_cf: minor cpp fixing/cleaning
* tag 'tag/upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata: ahci_platform: Add synopsys ahci controller in DT's compatible list
ata/pata_arasan_cf: Move arasan_cf_pm_ops out of #ifdef, #endif macros
libata: init ata_print_id to 0
ahci: Detect Marvell 88SE9172 SATA controller
libata: skip old error history when counting probe trials
Pull i2c embedded fixes from Wolfram Sang:
"Here are some typical i2c driver bugfixes for 3.4. Missed clock
handling, improper timeout fixes, hardware wrokarounds... All
patches have been in linux-next for a few days, too."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: mxs: disable QUEUE when sending is done
i2c: mxs: handle spurious interrupt
i2c-eg20t: Modify MODULE_AUTHOR's email address
i2c-eg20t: change timeout value 50msec to 1000msec
i2c: tegra: Add delay before resetting the controller after NACK
i2c: pnx: Disable clk in suspend
Pull drm fixes from Dave Airlie:
"Just some regression fixes from Ben along with a variable that gcc
failed to spot is uninitialised."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
nouveau: initialise has_optimus variable.
drm/nv10/gpio: fix thinko in mask for gpio lines 2-9
nvc0/fb: shut up PMFB interrupt after the first occurrence
drm/nouveau/hdmi: use correct hdmi regs for nvaa/nvac
drm/nouveau/bios: fix regression on some nv4x board
Pull networking fixes from David Miller:
1) Transfer padding was wrong for full-speed USB in ASIX driver, fix
from Ingo van Lil.
2) Propagate the negative packet offset fix into the PowerPC BPF JIT.
From Jan Seiffert.
3) dl2k driver's private ioctls were letting unprivileged tasks make
MII writes and other ugly bits like that. Fix from Jeff Mahoney.
4) Fix TX VLAN and RX packet drops in ucc_geth, from Joakim Tjernlund.
5) OOPS and network namespace fixes in IPVS from Hans Schillstrom and
Julian Anastasov.
6) Fix races and sleeping in locked context bugs in drop_monitor, from
Neil Horman.
7) Fix link status indication in smsc95xx driver, from Paolo Pisati.
8) Fix bridge netfilter OOPS, from Peter Huang.
9) L2TP sendmsg can return on error conditions with the socket lock
held, oops. Fix from Sasha Levin.
10) udp_diag should return meaningful values for socket memory usage,
from Shan Wei.
11) Eric Dumazet is so awesome he gets his own section:
Socket memory cgroup code (I never should have applied those
patches, grumble...) made erroneous changes to
sk_sockets_allocated_read_positive(). It was changed to
use percpu_counter_sum_positive (which requires BH disabling)
instead of percpu_counter_read_positive (which does not).
Revert back to avoid crashes and lockdep warnings.
Adjust the default tcp_adv_win_scale and tcp_rmem[2] values
to fix throughput regressions. This is necessary as a result
of our more precise skb->truesize tracking.
Fix SKB leak in netem packet scheduler.
12) New device IDs for various bluetooth devices, from Manoj Iyer,
AceLan Kao, and Steven Harms.
13) Fix command completion race in ipw2200, from Stanislav Yakovlev.
14) Fix rtlwifi oops on unload, from Larry Finger.
15) Fix hard_mtu when adjusting hard_header_len in smsc95xx driver.
From Stephane Fillod.
16) ehea driver registers it's IRQ before all the necessary state is
setup, resulting in crashes. Fix from Thadeu Lima de Souza
Cascardo.
17) Fix PHY connection failures in davinci_emac driver, from Anatolij
Gustschin.
18) Missing break; in switch statement in bluetooth's
hci_cmd_complete_evt(). Fix from Szymon Janc.
19) Fix queue programming in iwlwifi, from Johannes Berg.
20) Interrupt throttling defaults not being actually programmed into the
hardware, fix from Jeff Kirsher and Ying Cai.
21) TLAN driver SKB encoding in descriptor busted on 64-bit, fix from
Benjamin Poirier.
22) Fix blind status block RX producer pointer deref in TG3 driver, from
Matt Carlson.
23) Promisc and multicast are busted on ehea, fixes from Thadeu Lima de
Souza Cascardo.
24) Fix crashes in 6lowpan, from Alexander Smirnov.
25) tcp_complete_cwr() needs to be careful to not rewind the CWND to
ssthresh if ssthresh has the "infinite" value. Fix from Yuchung
Cheng.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
sungem: Fix WakeOnLan
tcp: change tcp_adv_win_scale and tcp_rmem[2]
net: l2tp: unlock socket lock before returning from l2tp_ip_sendmsg
drop_monitor: prevent init path from scheduling on the wrong cpu
usbnet: fix failure handling in usbnet_probe
usbnet: fix leak of transfer buffer of dev->interrupt
ucc_geth: Add 16 bytes to max TX frame for VLANs
net: ucc_geth, increase no. of HW RX descriptors
netem: fix possible skb leak
sky2: fix receive length error in mixed non-VLAN/VLAN traffic
sky2: propogate rx hash when packet is copied
net: fix two typos in skbuff.h
cxgb3: Don't call cxgb_vlan_mode until q locks are initialized
ixgbe: fix calling skb_put on nonlinear skb assertion bug
ixgbe: Fix a memory leak in IEEE DCB
igbvf: fix the bug when initializing the igbvf
smsc75xx: enable mac to detect speed/duplex from phy
smsc75xx: declare smsc75xx's MII as GMII capable
smsc75xx: fix phy interrupt acknowledge
smsc75xx: fix phy init reset loop
...
Fix OOPS seen in coretemp driver if the CPU core ID is too large
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=iNOt
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fix OOPS seen in coretemp driver if the CPU core ID is too large"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (coretemp) Increase CPU core limit
hwmon: (coretemp) fix oops on cpu unplug
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Support Department <support@connecttech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
CC: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Anton Samokhvalov <pg83@yandex.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Thomas Tuttle <ttuttle@chromium.org>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Rigbert Hamisch <rigbert@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Johan Hovold <jhovold@gmail.com>
CC: Donald Lee <donald@asix.com.tw>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Oliver Neukum <oneukum@suse.de>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Johan Hovold <jhovold@gmail.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
CC: Simon Arlott <simon@fire.lp0.eu>
CC: Andrew Worsley <amworsley@gmail.com>
CC: "Michał Wróbel" <michal.wrobel@flytronic.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Gary Brubaker <xavyer@ix.netcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Peter Berger <pberger@brimson.com>
CC: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Lonnie Mendez <dignome@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Matthias Bruestle and Harald Welte <support@reiner-sct.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Johan Hovold <jhovold@gmail.com>
CC: Preston Fick <preston.fick@silabs.com>
CC: Yuri Matylitski <ym@tekinsoft.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: William Greathouse <wgreathouse@smva.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This removes most of the dbg() calls, as they were just tracing calls,
and converts the remaining ones to dev_dbg().
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the usage of dbg() to dev_dbg() where needed, and removed
a bunch of these calls where they were just "tracing" calls, which are
no longer needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The upcoming Intel Lynx Point chipset includes an xHCI host controller
that can have ports switched from the EHCI host controller, just like
the Intel Panther Point xHCI host. This time, ports from both EHCI
hosts can be switched to the xHCI host controller. The PCI config
registers to do the port switching are in the exact same place in the
xHCI PCI configuration registers, with the same semantics.
Hooray for shipping patches for next-gen hardware before the current gen
hardware is even available for purchase!
This patch should be backported to stable kernels as old as 3.0,
that contain commit 69e848c209
"Intel xhci: Support EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
If the user chooses to say "no" to CONFIG_USB_XHCI_HCD on a system
with an Intel Panther Point chipset, the PCI quirks code or the EHCI
driver will switch the ports over to the xHCI host, but the xHCI driver
will never load. The ports will be powered off and seem "dead" to the
user.
Fix this by only switching the ports over if CONFIG_USB_XHCI_HCD is
either compiled in, or compiled as a module.
This patch should be backported to stable kernels as old as 3.0,
that contain commit 69e848c209
"Intel xhci: Support EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Eric Anholt <eric.anholt@intel.com>
Reported-by: David Bein <d.bein@f5.com>
Cc: stable@vger.kernel.org
While testing unplugging an UVC HD webcam with usb-redirection (so through
usbdevfs), my userspace usb-redir code was getting a value of -1 in
iso_frame_desc[n].status, which according to Documentation/usb/error-codes.txt
is not a valid value.
The source of this -1 is the default case in xhci-ring.c:process_isoc_td()
adding a kprintf there showed the value of trb_comp_code to be COMP_TX_ERR
in this case, so this patch adds handling for that completion code to
process_isoc_td().
This was observed and tested with the following xhci controller:
1033:0194 NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)
Note: I also wonder if setting frame->status to -1 (-EPERM) is the best we can
do, but since I cannot come up with anything better I've left that as is.
This patch should be backported to kernels as old as 2.6.36, which contain the
commit 04e51901dd "USB: xHCI: Isochronous
transfer implementation".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This commit adds a bit-array to xhci bus_state for keeping track of
which ports are undergoing a resume transition. If any of the bits
are set when xhci_hub_status_data() is called, the routine will return
a non-zero value even if no ports have any status changes pending.
This will allow usbcore to handle races between root-hub suspend and
port wakeup.
This patch should be backported to kernels as old as 3.4, that contain
the commit 879d38e6bc "USB: fix race
between root-hub suspend and remote wakeup".
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
SPEAr13xx series of SoCs contain Synopsys AHCI SATA Controller which shares
ahci_platform driver with other controller versions.
This patch updates DT compatible list for ahci_platform. It also updates and
renames binding documentation to more generic name.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
#ifdef, #endif is not required in definition/usage of arasan_cf_pm_ops. So, move
this definition and its usage outside of them.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When comparing the dmesg between 3.4-rc3 and 3.4-rc4 I found the
following differences:
-ata1: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff100 irq 47
-ata2: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff180 irq 47
-ata3: DUMMY
+ata2: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff100 irq 47
+ata3: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff180 irq 47
ata4: DUMMY
ata5: DUMMY
-ata6: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff380 irq 47
+ata6: DUMMY
+ata7: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff380 irq 47
The change of numbering comes from commit 85d6725b7c ("libata:
make ata_print_id atomic") that changed lines like
ap->print_id = ata_print_id++;
to
ap->print_id = atomic_inc_return(&ata_print_id);
As the latter behaves like ++ata_print_id, we must initialize
it to zero to start the numbering from one.
Signed-off-by: Tero Roponen <tero.roponen@gmail.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The Marvell 88SE9172 SATA controller (PCI ID 1b4b 917a) already worked
once it was detected, but was missing an ahci_pci_tbl entry.
Boot tested on a Gigabyte Z68X-UD3H-B3 motherboard.
Signed-off-by: Matt Johnson <johnso87@illinois.edu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit d902747("[libata] Add ATA transport class") introduced
ATA_EFLAG_OLD_ER to mark entries in the error ring as cleared.
But ata_count_probe_trials_cb() didn't check this flag and it still
counts the old error history. So wrong probe trials count is returned
and it causes problem, for example, SATA link speed is slowed down from
3.0Gbps to 1.5Gbps.
Fix it by checking ATA_EFLAG_OLD_ER in ata_count_probe_trials_cb().
Cc: stable <stable@vger.kernel.org> # 2.6.37+
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: enable dip before writing data on gen4
fixing dmi match for hp t5745 and hp st5747 thin client
drm/i915: Only enable IPS polling for gen5
drm/i915: Do not read non-existent DPLL registers on PCH hardware
While testing with the intel_infoframes tool on gen4, I see that when
video DIP is disabled, what we write to the DATA memory is not exactly
what we read back later.
This regression has been introduce in
commit 64a8fc0145
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Thu Sep 22 11:16:00 2011 +0530
drm/i915: fix ILK+ infoframe support
That commit was setting VIDEO_DIP_CTL to 0 when initializing, which
caused the problem.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=43947
Cc: stable@kernel.org
Tested-by: Yang Guang <guang.a.yang@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
[danvet: Pimped commit message by using the usual commit citation
layout.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WakeOnLan was broken in this driver because gp->asleep_wol is a 1-bit
bitfield and it was being assigned WAKE_MAGIC, which is (1 << 5).
gp->asleep_wol remains 0 and the machine never wakes up. Fixed by casting
gp->wake_on_lan to bool. Tested on an iBook G4.
Signed-off-by: Gerard Lledo <gerard.lledo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If register_netdev returns failure, the dev->interrupt and
its transfer buffer should be released, so just fix it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The transfer buffer of dev->interrupt is allocated in .probe path,
but not freed in .disconnet path, so mark the interrupt URB as
URB_FREE_BUFFER to free the buffer when the URB is destroyed.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creating a VLAN interface on top of ucc_geth adds 4 bytes
to the frame and the HW controller is not prepared to
TX a frame bigger than 1518 bytes which is 4 bytes too
small for a full VLAN frame. Add 16 bytes which will handle
the a simple VLAN and leaves 12 bytes for future expansion.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a busy network we see ucc_geth is dropping RX pkgs every now
and then. Increase the RX queues HW descriptors from
16 to 32 to deal with this.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are two EHCI Tegra driver patches for your tree.
The first is a bit big, but the majority is just moving code around. It
is needed due to the other EHCI core changes that went in way back in
3.4-rc1, so this driver will now properly handle suspend/resume, as it
was broken. The other one is a minor bugfix that resolves an warning
that people have been seeing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+hli8ACgkQMUfUDdst+ymGdgCeKYDYx5w2N+tmSy50kjDEhSQI
534AoK3+ZQUNsEyLU8ufLtNOyPrtIH3i
=5LmY
-----END PGP SIGNATURE-----
Merge tag 'usb-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here are two EHCI Tegra driver patches for your tree.
The first is a bit big, but the majority is just moving code around.
It is needed due to the other EHCI core changes that went in way back
in 3.4-rc1, so this driver will now properly handle suspend/resume, as
it was broken. The other one is a minor bugfix that resolves an
warning that people have been seeing."
* tag 'usb-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: ehci-tegra: remove redundant gpio_set_value
EHCI: update PM methods in ehci-tegra.c
This is a deadlock bugfix that was easy to hit, and that the vt layer lock
rework got wrong, so it reverts the logic back to the way it was in 3.3 and
earlier kernels to prevent problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+hlr4ACgkQMUfUDdst+ynGqwCfeaot2snAEoWi1qp1pU+4cAJn
8gwAoLaO//pVnVmUIplPMRtFr3tuUN/h
=z8wN
-----END PGP SIGNATURE-----
Merge tag 'tty-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull a TTY fix from Greg Kroah-Hartman:
"This is a deadlock bugfix that was easy to hit, and that the vt layer
lock rework got wrong, so it reverts the logic back to the way it was
in 3.3 and earlier kernels to prevent problems."
* tag 'tty-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vt: Fix deadlock on scroll-lock
The original request types in the cp210x driver are labled as "DEVICE_TO_HOST" and
"HOST_TO_DEVICE" but the actual bit definition corresponds to a request to the
interface. This has been corrected, and the actual definition for the device
requests have been added.
Signed-off-by: Preston Fick <preston.fick@silabs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On SandyBridge IPS was entirely implemented in hardware and not reliant
on the driver monitoring power consumption and feeding back desired run
states, so the hardware is able to adapt quicker and more flexibly. Which
is a huge relief for us as we no longer have to carry empirically
derived magic algorithms.
Yet despite the advance in technology, the driver was still doing its
IPS polling on all machines. Restrict it to the only supported hardware,
Clarkdale/Arrandale.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49025
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only execute intel_decrease_pllclock for pre-PCH hardware, typically
gen4 mobiles. However, in the variable declaration we did read from the
non-PCH DPLL register, quite naughty and detected by SandyBridge.
Reported-and-tested-by: Andrey Rahmatullin <wrar@wrar.name>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49025
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Issue an Update Transfer command after queuing a request to an isoc
EP with an active transfer. This is required according to the dwc3
databook. Pratyush Anand reports that this fixes a problem he was
having with Isoc IN transfers.
Tested-by: Pratyush Anand<pratyush.anand@st.com>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is basically a noop for DWC3. We don't have
to do anything. Basically we test if the request
parameters are correct, cache the Isochronous
Delay and return success.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We want to re-use that buffer for other USB
requests, so let's increase it to biggest
wMaxPacketSize for ep0 so it works for everything
we have in mind.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch implements Set SEL Standard Request
support for dwc3 driver. It needs to issue a command
to the controller passing the timing we received on
the data phase of the Set SEL request.
Signed-off-by: Felipe Balbi <balbi@ti.com>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Zack Parsons <k3bacon@gmail.com>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Cesar Miquel <miquel@df.uba.ar>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Tobias Klauser <tklauser@distanz.ch>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: David Howells <dhowells@redhat.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Duncan Sands <duncan.sands@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Duncan Sands <duncan.sands@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Simon Arlott <cxacru@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Henrik Rydberg <rydberg@euromail.se>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Viresh Kumar <viresh.kumar@st.com>
CC: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Jesper Juhl <jj@chaosbits.net>
CC: JJ Ding <dgdunix@gmail.com>
CC: Edwin van Vliet <edwin@cheatah.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Henrik Rydberg <rydberg@euromail.se>
CC: Alessandro Rubini <rubini@ipvvis.unipv.it>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Alessandro Rubini <rubini@ipvvis.unipv.it>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Henk Vergonet <Henk.Vergonet@gmail.com>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: "Magnus Hörlin" <magnus@alefors.se>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Ping Cheng <pingc@wacom.com>
Cc: Eduard Hasenleithner <eduard@hasenleithner.at>
Cc: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should always reference the input device for dev_err(), not the USB
device. Fix up the places where I got this wrong.
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Henrik Rydberg <rydberg@euromail.se>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Viresh Kumar <viresh.kumar@st.com>
CC: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should always reference the input device for dev_err(), not the USB
device. Fix up the places where I got this wrong.
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Ping Cheng <pingc@wacom.com>
CC: Chris Bagwell <chris@cnpbagwell.com>
CC: Eduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should always reference the input device for dev_err(), not the USB
device. Fix up the places where I got this wrong.
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should always reference the input device for dev_err(), not the USB
device. Fix up the places where I got this wrong.
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should always reference the input device for dev_err(), not the USB
device. Fix up the places where I got this wrong.
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Jesper Juhl <jj@chaosbits.net>
CC: JJ Ding <dgdunix@gmail.com>
CC: Edwin van Vliet <edwin@cheatah.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should always reference the input device for dev_err(), not the USB
device. Fix up the places where I got this wrong.
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should always reference the input device for dev_err(), not the USB
device. Fix up the places where I got this wrong.
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Henrik Rydberg <rydberg@euromail.se>
CC: Alessandro Rubini <rubini@ipvvis.unipv.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should always reference the input device for dev_err(), not the USB
device. Fix up the places where I got this wrong.
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Alessandro Rubini <rubini@ipvvis.unipv.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should always reference the input device for dev_err(), not the USB
device. Fix up the places where I got this wrong.
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Henk Vergonet <Henk.Vergonet@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should always reference the input device for dev_err(), not the USB
device. Fix up the places where I got this wrong.
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should always reference the input device for dev_err(), not the USB
device. Fix up the places where I got this wrong.
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should always reference the input device for dev_err(), not the USB
device. Fix up the places where I got this wrong.
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should always reference the input device for dev_err(), not the USB
device. Fix up the places where I got this wrong.
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: "Magnus Hörlin" <magnus@alefors.se>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should always reference the input device for dev_err(), not the USB
device. Fix up the places where I got this wrong.
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit af4e1ee040 (usb-next)
"USB: remove err() macro"
was preceeded by a tree-wide cleanup of users, however this
one squeaked through the cracks because it had whitespace
between the function name and the bracket for the args.
Map it onto dev_err, just like all the "pre-commits" made
in advance of af4e1ee040, such as the example seen in
the commit d57b177208:
"USB: ohci-xls.c: remove err() usage"
Build tested with the ARM magician_defconfig settings.
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit af4e1ee040 (usb-next)
"USB: remove err() macro"
was preceeded by a tree-wide cleanup of users, however this
one squeaked through the cracks because it had whitespace
between the function name and the bracket for the args.
Map it onto dev_err, just like all the "pre-commits" made
in advance of af4e1ee040, such as the example seen in
the commit d57b177208:
"USB: ohci-xls.c: remove err() usage"
Build tested with the MIPS pnx8550-jbs_defconfig settings.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit af4e1ee040 (usb-next)
"USB: remove err() macro"
was preceeded by a tree-wide cleanup of users, however this
one squeaked through the cracks because it had whitespace
between the function name and the bracket for the args.
Map it onto dev_err, just like all the "pre-commits" made
in advance of af4e1ee040, such as the example seen in
the commit d57b177208:
"USB: ohci-xls.c: remove err() usage"
Build tested with the MIPS gpr_defconfig settings.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The immediately preceding gpio_direction_output() already set the value,
so there's no need to repeat it. This also prevents gpio_set_value() from
WARNing when the GPIO is sleepable (e.g. is on an I2C expander); the set
direction API is always sleepable, but plain set_value isn't.
Cc: <stable@vger.kernel.org> # v3.3
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1547) rearranges the Power Management parts of the
ehci-tegra driver to match the conventions used in other EHCI platform
drivers. In particular, the controller should not be powered down by
the root hub's suspend routine; the controller's power level should be
managed by the controller's own PM methods.
The end result of the patch is that the standard ehci_bus_suspend()
and ehci_bus_resume() methods can be used instead of special-purpose
routines. The driver now uses the standard dev_pm_ops methods instead
of legacy power management. Since there is no supported wakeup
mechanism for the controller, runtime suspend is forbidden by default
(this can be overridden via sysfs, if desired).
These adjustments are needed in order to make ehci-tegra compatible
with recent changes to the USB core. The core now checks the root
hub's status following bus suspend; if the controller is automatically
powered down during bus suspend then the check will fail and the root
hub will be resumed immediately. Doing the controller power-down in a
separate method avoids this problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixing the locking accidentally replaced a race in the scroll
lock handling with a deadlock. Turn it back into a race for
now.
The basic problem is that there are two paths into the tty
stop/start helpers. One via the tty layer ^S/^Q handling
where we need to take the kbd_event_lock and one via the
special keyboard handler for fn_hold where we already hold
it. Probably we need to split out into a separate LED lock
but for now just go back to the race as it's a bit close
to release.
Reported-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bug: The VLAN bit of the MAC RX Status Word is unreliable in several older
supported chips. Sometimes the VLAN bit is not set for valid VLAN packets
and also sometimes the VLAN bit is set for non-VLAN packets that came after
a VLAN packet. This results in a receive length error when VLAN hardware
tagging is enabled.
Fix: Variation on original fix proposed by Mirko.
The VLAN information is decoded in the status loop, and can be
applied to the received SKB there. This eliminates the need for the
separate tag field in the interface data structure. The tag has to
be copied and cleared if packet is copied. This version checked out
with vlan and normal traffic.
Note: vlan_tx_tag_present should be renamed vlan_tag_present, but that
is outside scope of this.
Reported-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a small packet is received, the driver copies it to a new skb to allow
reusing the full size Rx buffer. The copy was propogating the checksum offload
but not the receive hash information. The bug is impact was mostly harmless
and therefore not observed until reviewing this area of code.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bMaxPacketSize0 field for super speed is a power of 2, not a count.
The size itself is always 512.
Max packet size for a super speed bulk endpoint is 1024, so
allocate the urb size in halt_simple() accordingly.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ohci-nxp duplicates the isp1301 driver. This patch removes this code and makes
ohci-nxp use the new separate isp1301 driver instead.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a USB gadget driver for the LPC32xx ARM SoC.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This new driver registers the NXP ISP1301 chip via the I2C subsystem. The chip
is the USB transceiver shared by ohci-nxp, lpc32xx_udc (gadget) and
isp1301_omap.
ISP1301 is a very low-level driver that primarily separates out the I2C client
registration of the ISP1301 chip (including instantiation via DT), used by
other drivers, and declares the chip's registers. It's only a helper driver for
some OHCI and USB device drivers. The driver can be considered as a register
set extension of ohci-nxp, lpc32xx-udc and isp1301_omap, which in turn know
best what to do with the low level functionality (individual ISP1301 registers
and timing, see the different initialization strategies in those drivers).
Those drivers previously internally duplicated ISP1301 register definitions
which is solved by this new isp1301 driver. The ISP1301 registers exposed via
isp1301.h can be accessed by other drivers using it with standard i2c_smbus_*()
accesses.
Following patches let the respective USB host and gadget drivers use this
driver, instead of duplicating ISP1301 handling.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds device tree support to ohci-nxp.c
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some HCDs usb_unlink_urb() can directly call the
completion handler. That limits the spinlocks that can
be taken in the handler to locks not held while calling
usb_unlink_urb()
To prevent a race with resubmission, this patch exposes
usbcore's infrastructure for blocking submission, uses it
and so drops the lock without causing a race in usbhid.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CPU core ID is used to index the core_data[] array. The core ID is, however, not
sequential; 10-core CPUS can have a core ID as high as 25. Increase the limit to
32 to be able to deal with current CPUs.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Durgadoss R <durgadoss.r@intel.com>
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nv10/gpio: fix thinko in mask for gpio lines 2-9
nvc0/fb: shut up PMFB interrupt after the first occurrence
drm/nouveau/hdmi: use correct hdmi regs for nvaa/nvac
drm/nouveau/bios: fix regression on some nv4x board
'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' removes the include for
linux/gpio.h from omap-usb-host.c. This include indirectly includes plat/cpu.h
which is required by omap-usb-host.c. Fix the build breakage by including
it directly.
Acked-by: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver calls cxgb_vlan_mode() from init_one(). This calls into
synchronize_rx(), which locks all the q locks, but the q locks are not
initialized until cxgb_up() -> setup_sge_qsets(). So move the call to
cxgb_vlan_mode() into cxgb_up(), after the call to setup_sge_qsets().
We also move the body of these functions up higher to avoid having to
a forward declaration.
This was found because of the lockdep warning:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 323, comm: work_for_cpu Not tainted 3.4.0-rc5 #28
Call Trace:
[<ffffffff8106e767>] register_lock_class+0x108/0x2d0
[<ffffffff8106ff42>] __lock_acquire+0xd3/0xd06
[<ffffffff81070fd0>] lock_acquire+0xbf/0xfe
[<ffffffff813862a6>] _raw_spin_lock_irq+0x36/0x45
[<ffffffffa01e71aa>] cxgb_vlan_mode+0x96/0xcb [cxgb3]
[<ffffffffa01f90eb>] init_one+0x8c4/0x980 [cxgb3]
[<ffffffff811fcbf0>] local_pci_probe+0x3f/0x70
[<ffffffff81042206>] do_work_for_cpu+0x10/0x22
[<ffffffff810482de>] kthread+0xa1/0xa9
[<ffffffff8138e234>] kernel_thread_helper+0x4/0x10
Contrary to what lockdep says, the code is not fine: we are locking an
uninitialized spinlock.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the support to bounce buffer added, the skb is coming as nonlinear in the
case of non-DDPed data frames for FCoE, which is mostly ok as the FCoE stack
would take care of that. However, for target mode, we have to set the FC CRC
and FC EOF field to allow the protocol stack to not drop the frame for the last
data frame of that sequence. So fix this by linearizing the skb first before
doing skb_put().
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
