* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, hpet: Stop soliciting hpet=force users on ICH4M
x86: check boundary in setup_node_bootmem()
uv_time: add parameter to uv_read_rtc()
x86: hpet: fix periodic mode programming on AMD 81xx
x86: more than 8 32-bit CPUs requires X86_BIGSMP
x86: avoid theoretical spurious NMI backtraces with CONFIG_CPUMASK_OFFSTACK=y
x86: fix boot crash in NMI watchdog with CONFIG_CPUMASK_OFFSTACK=y and flat APIC
x86-64: fix FPU corruption with signals and preemption
x86/uv: fix for no memory at paddr 0
docs, x86: add nox2apic back to kernel-parameters.txt
x86: mm/numa_32.c calculate_numa_remap_pages should use __init
x86, kbuild: make "make install" not depend on vmlinux
x86/uv: fix init of cpu-less nodes
x86/uv: fix init of memory-less nodes
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/irq: mark NUMA_MIGRATE_IRQ_DESC broken
x86, irq: Remove IRQ_DISABLED check in process context IRQ move
The HPET in the ICH4M is not documented in the data sheet
because it was not officially validated.
While it is fine for hackers to continue to use "hpet=force"
to enable the hardware that they have, it is not prudent to
solicit additional "hpet=force" users on this hardware.
[ Impact: remove hpet=force syslog message on old-ICH systems ]
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
LKML-Reference: <alpine.LFD.2.00.0904231918510.15843@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
uv_read_rtc() is referenced by read member of struct clocksource clocksource_uv.
In include/linux/clocksource.h, read of struct clocksource is declared as:
cycle_t (*read)(struct clocksource *cs)
This got introduced recently in:
8e19608: clocksource: pass clocksource to read() callback
But arch/x86/kernel/uv_time.c was not properly converted by that pach.
This patch adds a dummy parameter (struct clocksource type) to uv_read_rtc() to
fix the incompatible reference in clocksource_uv, and add a NULL parameter in
all places where uv_read_rtc() gets called.
[ Impact: cleanup, address compiler warning ]
Signed-off-by: Coly Li <coly.li@suse.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Magnus Damm <damm@igel.co.jp>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Hugh Dickins <hugh@veritas.com>
LKML-Reference: <49EF3614.1050806@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Dimitri Sivanich <sivanich@sgi.com>
(See http://bugzilla.kernel.org/show_bug.cgi?id=12961)
It partially reverts commit c23e253e67
(x86: hpet: stop HPET_COUNTER when programming periodic mode)
HPET on AMD 81xx chipset needs a second write (with HPET_TN_SETVAL
cleared) to T0_CMP register to set the period in periodic mode.
With this patch HPET_COUNTER is still stopped but not reset when HPET
is programmed in periodic mode. This should help to avoid races when
HPET is programmed in periodic mode and fixes a boot time hang that
I've observed on a machine when using 1000HZ.
[ Impact: fix boot time hang on machines with AMD 81xx chipset ]
Reported-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Tested-by: Jeff Mahoney <jeffm@suse.com>
LKML-Reference: <20090421180037.GA2763@alberich.amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In theory (though not shown in practice) alloc_cpumask_var() doesn't zero
memory, so CPUs might print an "NMI backtrace for cpu %d" once on boot.
(Bug introduced in fcef8576d8).
[ Impact: avoid theoretical syslog noise in rare configs ]
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <alpine.DEB.2.00.0904202113520.10097@gandalf.stny.rr.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fcef8576d8 converted backtrace_mask to a
cpumask_var_t, and assumed check_nmi_watchdog was called before
nmi_watchdog_tick was ever called. Steven's oops shows I was wrong.
This is something of a bandaid: I'm not sure we *should* be calling
nmi_watchdog_tick before check_nmi_watchdog. Note that gcc eliminates
this test for the CONFIG_CPUMASK_OFFSTACK=n case.
[ Impact: fix boot crash in rare configs ]
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <alpine.DEB.2.00.0904202113520.10097@gandalf.stny.rr.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In 64bit signal delivery path, clear_used_math() was happening before saving
the current active FPU state on to the user stack for signal handling. Between
clear_used_math() and the state store on to the user stack, potentially we
can get a page fault for the user address and can block. Infact, while testing
we were hitting the might_fault() in __clear_user() which can do a schedule().
At a later point in time, we will schedule back into this process and
resume the save state (using "xsave/fxsave" instruction) which can lead
to DNA fault. And as used_math was cleared before, we will reinit the FP state
in the DNA fault and continue. This reinit will result in loosing the
FPU state of the process.
Move clear_used_math() to a point after the FPU state has been stored
onto the user stack.
This issue is present from a long time (even before the xsave changes
and the x86 merge). But it can easily be exposed in 2.6.28.x and 2.6.29.x
series because of the __clear_user() in this path, which has an explicit
__cond_resched() leading to a context switch with CONFIG_PREEMPT_VOLUNTARY.
[ Impact: fix FPU state corruption ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: <stable@kernel.org> [2.6.28.x, 2.6.29.x]
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Fix endcase where the memory at physical address 0 does not really
exist AND one of the sockets on blade 0 has no active cpus.
The memory that _appears_ to be at physical address 0 is actually
memory that located at a different address but has been remapped by
the chipset so that it appears to be at physical address 0.
When determining the UV pnode, the algorithm for determining the pnode
incorrectly used the relocated physical address instead of the actual
(global) address.
[ Impact: boot failure on partitioned systems ]
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090420132530.GA23156@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Take already available policy->cpuinfo.max_freq and get rid of acpi-cpufreq
specific max_freq variable.
This implies that P0 is always the highest frequency which should always
be true as ACPI spec says:
As a result, the zeroth entry describes the highest performance state
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
I hit the check_flags error of lockdep:
WARNING: at kernel/lockdep.c:2893 check_flags+0x1a7/0x1d0()
[...]
hardirqs last enabled at (12567): [<ffffffff8026206a>] local_bh_enable+0xaa/0x110
hardirqs last disabled at (12569): [<ffffffff80610c76>] int3+0x16/0x40
softirqs last enabled at (12566): [<ffffffff80514d2b>] lock_sock_nested+0xfb/0x110
softirqs last disabled at (12568): [<ffffffff8058454e>] tcp_prequeue_process+0x2e/0xa0
The check_flags warning of lockdep tells me that lockdep thought interrupts
were disabled, but they were really enabled.
The numbers in the above parenthesis show the order of events:
12566: softirqs last enabled: lock_sock_nested
12567: hardirqs last enabled: local_bh_enable
12568: softirqs last disabled: tcp_prequeue_process
12566: hardirqs last disabled: int3
int3 is a breakpoint!
Examining this further, I have CONFIG_NET_TCPPROBE enabled which adds
break points into the kernel.
The paranoid_exit of the return of int3 does not account for enabling
interrupts on return to kernel. This code is a bit tricky since it
is also used by the nmi handler (when lockdep is off), and we must be
careful about the swapgs. We can not call kernel code after the swapgs
has been performed.
[ Impact: fix lockdep check_flags warning + self-turn-off ]
Acked-by: Peter Zijlsta <a.p.zijlstra@chello.nl>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix an endcase in the UV initialization code for the "UV large system mode"
of apicids. If node zero contains no cpus, cpus on another node will be the
boot cpu. The percpu data that contains the extra apicid bits was not
being initialized early enough.
[ Impact: fix potential boot crash on cpu-less UV nodes ]
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090417142447.GA23759@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix microcode driver newly spewing warnings
x86, PAT: Remove page granularity tracking for vm_insert_pfn maps
x86: disable X86_PTRACE_BTS for now
x86, documentation: kernel-parameters replace X86-32,X86-64 with X86
x86: pci-swiotlb.c swiotlb_dma_ops should be static
x86, PAT: Remove duplicate memtype reserve in devmem mmap
x86, PAT: Consolidate code in pat_x_mtrr_type() and reserve_memtype()
x86, PAT: Changing memtype to WC ensuring no WB alias
x86, PAT: Handle faults cleanly in set_memory_ APIs
x86, PAT: Change order of cpa and free in set_memory_wb
x86, CPA: Change idmap attribute before ioremap attribute setup
* 'x86/uv' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: UV BAU distribution and payload MMRs
x86: UV: BAU partition-relative distribution map
x86, uv: add Kconfig dependency on NUMA for UV systems
x86: prevent /sys/firmware/sgi_uv from being created on non-uv systems
x86, UV: Fix for nodes with memory and no cpus
x86, UV: system table in bios accessed after unmap
x86: UV BAU messaging timeouts
x86: UV BAU and nodes with no memory
Jeff Garzik reported this WARN_ON() noise:
> Kernel: 2.6.30-rc1-00306-g8371f87
> Hardware: ICH10 x86-64
>
> This is a regression from 2.6.29. Microcode spews the following WARNING
> multiple times during boot:
>
> ------------[ cut here ]------------
> WARNING: at fs/sysfs/group.c:138 sysfs_remove_group+0xeb/0xf0()
> Hardware name: sysfs group ffffffffa0209700 not found for
> kobject 'cpu0'
Keep sysfs files around for cpus even when we failed to locate
microcode for them at the moment of module loading. The appropriate
microcode firmware can become available later on.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch correctly sets BAU memory mapped registers to point
to the sending activation descriptor table and target payload table.
The "Broadcast Assist Unit" is used for TLB shootdown in UV.
The memory mapped registers that point to sending and receiving
memory structures contain node numbers.
In one case the __pa() function did not provide the node id of
memory on blade zero in configurations where that id is nonzero.
In another case, it was assumed that memory was allocated on
the local node. That assumption is not true in a configuration
in which the node has no memory.
Tested on the UV hardware simulator.
[ Impact: fix possible runtime crash due to incorrect TLB logic ]
Signed-off-by: Cliff Wickman <cpw@sgi.com>
LKML-Reference: <E1LuR5Z-0007An-B8@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It turns out that 'smp_call_function_many()' doesn't work at all like
'smp_call_function_single()', and my change to Andrew's patch to use it
rather than a loop over all CPU's acpi-cpufreq doesn't work.
My bad.
'smp_call_function_many()' has two "features" (aka "documented bugs"):
(a) it needs to be called with preemption disabled, because it uses
smp_processor_id() without guarding the CPU lookup with 'get_cpu()'
and 'put_cpu()' like the 'single' variant does.
(b) even if the current CPU is part of the CPU mask, it won't do the
call on that CPU.
Still, we're better off trying to use 'smp_call_function_many()' than
looping over CPU's, since it at least in theory allows us to use a
broadcast IPI and do it all in parallel. So let's just work around the
silly semantic bugs in that function.
Reported-and-tested-by: Ali Gholami Rudi <ali@rudi.ir>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>,
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert part of af5c820a31 ("x86: cpumask:
use work_on_cpu in arch/x86/kernel/microcode_core.c")
That change is causing only one Intel CPU's microcode to be updated e.g.
microcode: CPU3 updated from revision 0x9 to 0x17, date = 2005-04-22
where before it announced that also for CPU0 and CPU1 and CPU2.
We cannot use work_on_cpu() in the CONFIG_MICROCODE_OLD_INTERFACE code,
because Intel's request_microcode_user() involves a copy_from_user() from
/sbin/microcode_ctl, which therefore needs to be on that CPU at the time.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch enables each partition's BAU distribution bit map
to be partition-relative.
The distribution bitmap had been constructed assuming 0 as the base
node number. That construct would not have allowed a total system of
greater than 256 nodes.
It also corrects an error that occurred when the first blade's nasid
was not zero. That nasid was stored as the base node.
The base node number gets added by hardware to the node numbers implied
in the distribution bitmap, resulting in invalid target nasids.
Tested on the UV hardware simulator.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
LKML-Reference: <E1Ltl0C-0004Ob-37@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As discussed in the thread here:
http://marc.info/?l=linux-kernel&m=123964468521142&w=2
Eric W. Biederman observed:
> It looks like some additional bugs have slipped in since last I looked.
>
> set_irq_affinity does this:
> ifdef CONFIG_GENERIC_PENDING_IRQ
> if (desc->status & IRQ_MOVE_PCNTXT || desc->status & IRQ_DISABLED) {
> cpumask_copy(desc->affinity, cpumask);
> desc->chip->set_affinity(irq, cpumask);
> } else {
> desc->status |= IRQ_MOVE_PENDING;
> cpumask_copy(desc->pending_mask, cpumask);
> }
> #else
>
> That IRQ_DISABLED case is a software state and as such it has nothing to
> do with how safe it is to move an irq in process context.
[...]
>
> The only reason we migrate MSIs in interrupt context today is that there
> wasn't infrastructure for support migration both in interrupt context
> and outside of it.
Yes. The idea here was to force the MSI migration to happen in process
context. One of the patches in the series did
disable_irq(dev->irq);
irq_set_affinity(dev->irq, cpumask_of(dev->cpu));
enable_irq(dev->irq);
with the above patch adding irq/manage code check for interrupt disabled
and moving the interrupt in process context.
IIRC, there was no IRQ_MOVE_PCNTXT when we were developing this HPET
code and we ended up having this ugly hack. IRQ_MOVE_PCNTXT was there
when we eventually submitted the patch upstream. But, looks like I did a
blind rebasing instead of using IRQ_MOVE_PCNTXT in hpet MSI code.
Below patch fixes this. i.e., revert commit 932775a4ab
and add PCNTXT to HPET MSI setup. Also removes copying of desc->affinity
in generic code as set_affinity routines are doing it internally.
Reported-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Li Shaohua" <shaohua.li@intel.com>
Cc: Gary Hade <garyhade@us.ibm.com>
Cc: "lcm@us.ibm.com" <lcm@us.ibm.com>
Cc: suresh.b.siddha@intel.com
LKML-Reference: <20090413222058.GB8211@linux-os.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We ended up incorrectly using '&cur' instead of '&readin' in the
work_on_cpu() -> smp_call_function_single() transformation in commit
01599fca67 ("cpufreq: use
smp_call_function_[single|many]() in acpi-cpufreq.c").
Andrew explains:
"OK, the acpi tree went and had conflicting changes merged into it after
I'd written the patch and it appears that I incorrectly reverted part
of 18b2646fe3 while fixing the resulting
rejects.
Switching it to `readin' looks correct."
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: reduce kernel size a bit, address sparse warning
Addresses the problem pointed out by this sparse warning:
arch/x86/kernel/pci-swiotlb.c:53:20: warning: symbol 'swiotlb_dma_ops' was not declared. Should it be static?
For x86: swiotlb_dma_ops can be static, because it's not used outside
of pci-swiotlb.c
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
LKML-Reference: <1239558861.3938.2.camel@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: add linux kernel support for YMM state
x86: fix wrong section of pat_disable & make it static
x86: Fix section mismatches in mpparse
x86: fix set_fixmap to use phys_addr_t
x86: Document get_user_pages_fast()
x86, intr-remap: fix eoi for interrupt remapping without x2apic
Atttempting to rid us of the problematic work_on_cpu(). Just use
smp_call_fuction_single() here.
This repairs a 10% sysbench(oltp)+mysql regression which Mike reported,
due to
commit 6b44003e5c
Author: Andrew Morton <akpm@linux-foundation.org>
Date: Thu Apr 9 09:50:37 2009 -0600
work_on_cpu(): rewrite it to create a kernel thread on demand
It seems that the kernel calls these acpi-cpufreq functions at a quite
high frequency.
Valdis Kletnieks also reports that this causes 70-90 forks per second on
his hardware.
Cc: Valdis.Kletnieks@vt.edu
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Mike Galbraith <efault@gmx.de>
Cc: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
[ Made it use smp_call_function_many() instead of looping over cpu's
with smp_call_function_single() - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: save/restore Intel-AVX state properly between tasks
Intel Advanced Vector Extensions (AVX) introduce 256-bit vector processing
capability. More about AVX at http://software.intel.com/sites/avx
Add OS support for YMM state management using xsave/xrstor infrastructure
to support AVX.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1239402084.27006.8057.camel@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix section mismatch
In arch/x86/kernel/mpparse.c, smp_reserve_bootmem() has been called
and also refers to a function which is in .init section. Thus causes
the first warning. And check_irq_src() also requires an __init,
because it refers to an .init section.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <b9df5fa10904102004g51265d9axc8d07278bfdb6ba0@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To simplify level irq migration in the presence of interrupt-remapping,
Suresh used a virtual vector (io-apic pin number) to eliminate io-apic
RTE modification. Level triggered interrupt will appear as an edge to
the local apic cpu but still as level to the IO-APIC. So in addition to
do the local apic EOI, it still needs to do IO-APIC directed EOI to clear
the remote IRR bit in the IO-APIC RTE. Pls refer to Suresh's patch for
more details (commit 0280f7c416).
Now interrupt remapping is decoupled from x2apic, it also needs to do the
directed EOI for apic. Otherwise, apic interrupts won't work correctly.
Signed-off-by: Weidong Han <weidong.han@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Weidong Han <weidong.han@intel.com>
Cc: suresh.b.siddha@intel.com
Cc: dwmw2@infradead.org
Cc: allen.m.kay@intel.com
LKML-Reference: <1239355037-22856-1-git-send-email-weidong.han@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: cpu_debug remove execute permission
x86: smarten /proc/interrupts output for new counters
x86: DMI match for the Dell DXP061 as it needs BIOS reboot
x86: make 64 bit to use default_inquire_remote_apic
x86, setup: un-resequence mode setting for VGA 80x34 and 80x60 modes
x86, intel-iommu: fix X2APIC && !ACPI build failure
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: consolidate documents
blktrace: pass the right pointer to kfree()
tracing/syscalls: use a dedicated file header
tracing: append a comma to INIT_FTRACE_GRAPH
It seems by mistake these files got execute permissions so removing it.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
LKML-Reference: <1239211186.9037.2.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix build warnings and possibe compat misbehavior on IA64
Building a kernel on ia64 might trigger these ugly build warnings:
CC arch/ia64/ia32/sys_ia32.o
In file included from arch/ia64/ia32/sys_ia32.c:55:
arch/ia64/ia32/ia32priv.h:290:1: warning: "elf_check_arch" redefined
In file included from include/linux/elf.h:7,
from include/linux/module.h:14,
from include/linux/ftrace.h:8,
from include/linux/syscalls.h:68,
from arch/ia64/ia32/sys_ia32.c:18:
arch/ia64/include/asm/elf.h:19:1: warning: this is the location of the previous definition
[...]
sys_ia32.c includes linux/syscalls.h which in turn includes linux/ftrace.h
to import the syscalls tracing prototypes.
But including ftrace.h can pull too much things for a low level file,
especially on ia64 where the ia32 private headers conflict with higher
level headers.
Now we isolate the syscall tracing headers in their own lightweight file.
Reported-by: Tony Luck <tony.luck@intel.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jason Baron <jbaron@redhat.com>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Jiaying Zhang <jiayingz@google.com>
Cc: Michael Rubin <mrubin@google.com>
Cc: Martin Bligh <mbligh@google.com>
Cc: Michael Davidson <md@google.com>
LKML-Reference: <20090408184058.GB6017@nowhere>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now /proc/interrupts of tip tree has new counters:
PLT: Platform interrupts
Format change of output, as like that by commit:
commit 7a81d9a7da
x86: smarten /proc/interrupts output
should be applied to these new counters too.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <49C98DEA.8060208@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: restore old behavior
for flat and phys_flat
Signed-off-by: Yinhai Lu <yinghai@kernel.org.
LKML-Reference: <49DCBBF1.8080903@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
/sys/firmware/sgi_uv should only be created on uv systems.
Signed-off-by: Russ Anderson <rja@sgi.com>
LKML-Reference: <20090403222423.GA28546@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add support for Always Running APIC timer, CPUID_0x6_EAX_Bit2.
This bit means the APIC timer continues to run even when CPU is
in deep C-states.
The advantage is that we can use LAPIC timer on these CPUs
always, and there is no need for "slow to read and program"
external timers (HPET/PIT) and the timer broadcast logic
and related code in C-state entry and exit.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Do not write zeroes to APERF and MPERF by ondemand governor. With this
change, other users can share these MSRs for reads.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Change structure name to make the code cleaner and simpler. No
functionality change in this patch.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
branch tracer, intel-iommu: fix build with CONFIG_BRANCH_TRACER=y
branch tracer: Fix for enabling branch profiling makes sparse unusable
ftrace: Correct a text align for event format output
Update /debug/tracing/README
tracing/ftrace: alloc the started cpumask for the trace file
tracing, x86: remove duplicated #include
ftrace: Add check of sched_stopped for probe_sched_wakeup
function-graph: add proper initialization for init task
tracing/ftrace: fix missing include string.h
tracing: fix incorrect return type of ns2usecs()
tracing: remove CALLER_ADDR2 from wakeup tracer
blktrace: fix pdu_len when tracing packet command requests
blktrace: small cleanup in blk_msg_write()
blktrace: NUL-terminate user space messages
tracing: move scripts/trace/power.pl to scripts/tracing/power.pl
Replace all DMA_24BIT_MASK macro with DMA_BIT_MASK(24)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
