This patch adds a sysfs entry (/sys/devices/platform/_UDC_/gadget/suspended) to
show the suspend state of an USB composite gadget.
Signed-off-by: Fabien Chouteau <fabien.chouteau@barco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bulk endpoint streams were added in the USB 3.0 specification. Streams
allow a device driver to overload a bulk endpoint so that multiple
transfers can be queued at once.
The device then decides which transfer it wants to work on first, and can
queue part of a transfer before it switches to a new stream. All this
switching is invisible to the device driver, which just gets a completion
for the URB. Drivers that use streams must be able to handle URBs
completing in a different order than they were submitted to the endpoint.
This requires adding new API to set up xHCI data structures to support
multiple queues ("stream rings") per endpoint. Drivers will allocate a
number of stream IDs before enqueueing URBs to the bulk endpoints of the
device, and free the stream IDs in their disconnect function. See
Documentation/usb/bulk-streams.txt for details.
The new mass storage device class, USB Attached SCSI Protocol (UASP), uses
these streams API.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow the xHCI drivers (and any new USB 3.0 drivers) to parse the
SuperSpeed endpoint companion descriptor to find the maximum number of
bulk endpoint streams the endpoint supports. This is used to calculate
the maximum total number of streams the driver can allocate.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Definitions for registers defined by ULPI specification v1.1.
Signed-off-by: Heikki Krogerus <ext-heikki.krogerus@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
g_hid is a USB gadget driver implementing the Human Interface Device class
specification. The driver handles basic HID protocol handling in the
kernel, and allows userspace to read/write HID reports trough /dev/hidgX
character devices.
Signed-off-by: Fabien Chouteau <fabien.chouteau@barco.com>
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Generalise write buffer preparation.
This allows for drivers to manipulate (e.g. add headers) to bulk out
data before it is sent.
This adds a new function pointer to usb_serial_driver:
int (*prepare_write_buffer)(struct usb_serial_port *port,
void **dest, size_t size, const void *src, size_t count);
The function is generic and can be used with either kfifo-based or
multi-urb writes:
If *dest is NULL the implementation should allocate dest.
If src is NULL the implementation should use the port write fifo.
If not set, a generic implementation is used which simply uses memcpy or
kfifo_out.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use dynamic transfer buffer sizes since it is more efficient to let the
host controller do the partitioning to fit endpoint size. This way we
also do not use more than one urb per write request.
Replace max_in_flight_urbs with multi_urb_write flag in struct
usb_serial_driver to enable multi-urb writes.
Use MAX_TX_URBS=40 and a max buffer size of PAGE_SIZE to prevent DoS
attacks.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add process_read_urb to usb_serial_driver so that a driver can rely on
the generic read (and throttle) mechanism but still do device specific
processing of incoming data (such as adding tty_flags before pushing to
line discipline).
The default generic implementation handles sysrq for consoles but
otherwise simply pushes to tty.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the already exported function for submitting the read urb associated
with a usb_serial_port.
Make sure it returns the result of usb_submit_urb and rename to the
more descriptive usb_serial_generic_submit_read_urb.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow drivers to define custom bulk in/out buffer sizes in struct
usb_serial_driver. If not set, fall back to the default buffer size
which matches the endpoint size.
Three drivers are currently freeing the pre-allocated buffers and
allocating larger ones to achieve this at port probe (ftdi_sio) or even
at port open (ipaq and iuu_phoenix), which needless to say is suboptimal.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a new quirk USB_QUIRK_HONOR_BNUMINTERFACES, when this quirk is
set and a device has more interface descriptors in a configuration
then it claims to have in config->bNumInterfaces, ignore all additional
interfaces.
This is needed for devices which try to hide unused interfaces by only
lowering config->bNumInterfaces, and which can't handle if you try to talk
to the "hidden" interfaces.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rather than hardcoding the gpio levels for vrsel, allow the platform
resources to handle this so boards can be active high or low.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
boards might want to optimize their fifo configuration
to the particular needs of that specific board. Allow
that by moving all related data structures to
<linux/usb/musb.h>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace all instances of using the console variable in struct
usb_serial_port with the struct tty_port version.
CC: Alan Cox <alan@linux.intel.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: linux-usb@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1348) removes the bogus
USB_PORT_FEAT_{HIGHSPEED,SUPERSPEED} symbols from ch11.h. No such
features are defined by the USB spec. (There is a PORT_LOWSPEED
feature, but the spec doesn't mention it except to say that host
software should never use it.) The speed indicators are port
statuses, not port features.
As a temporary workaround for the xhci-hcd driver, a fictional
USB_PORT_STAT_SUPER_SPEED symbol is added.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Base on inputs from Alan Stern, split the hub.h header into:
- new ch11.h header (most of it) containing constants and
structures from chapter 11 of the USB 2.0 spec.
- a small remaining part being merged into hcd.h.
Signed-of-by: Eric Lescouet <eric@lescouet.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usbcore headers: hcd.h and hub.h are shared between usbcore,
HCDs and a couple of other drivers (e.g. USBIP modules).
So, it makes sense to move them into a more public location and
to cleanup dependency of those modules on kernel internal headers.
This patch moves hub.h from drivers/usb/core into include/linux/usb/
Signed-of-by: Eric Lescouet <eric@lescouet.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usbcore headers: hcd.h and hub.h are shared between usbcore,
HCDs and a couple of other drivers (e.g. USBIP modules).
So, it makes sense to move them into a more public location and
to cleanup dependency of those modules on kernel internal headers.
This patch moves hcd.h from drivers/usb/core into include/linux/usb/
Signed-of-by: Eric Lescouet <eric@lescouet.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For both UAC1 and UAC2, interrupt endpoint messages are now parsed with
structs rather that with anonymous buffer array accesses.
For UAC2, only CUR interrupt notifications are supported for now.
snd_usb_mixer_status_complete() was renamed to
snd_usb_mixer_interrupt().
Fixed one indentation flaw on the way.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This was missing on the definition of struct uac_iso_endpoint_descriptor
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 23caaf19b ("ALSA: usb-mixer: Add support for Audio Class v2.0")
broke support for Class1 devices due to two faulty changes. This patch
fixes it.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-and-Tested-by: The Source <thesourcehim@gmail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
USB Audio Class v2.0 compliant devices have different descriptors and a
different way of setting/getting min/max/res/cur properties. This patch
adds support for them.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce a number of new structs for mixer, selector, feature and
processing units and some static inline helpers to access fields which
have dynamic offsets. Use them in mixer.c to parse the descriptors. This
is necessary for the upcoming audio v2 parsers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Split the audio.h file in two to clearly denote the differences
between the standards.
- Add many more defines to audio-v2.h. Most of them are not currently
used.
- Replaced a magic value with a proper define
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (26 commits)
ALSA: hdmi - show debug message on changing audio infoframe
ALSA: hdmi - merge common code for intelhdmi and nvhdmi
ALSA: hda - Add ASRock mobo to MSI blacklist
ALSA: hda: uninitialized variable fix
ALSA: hda: Use LPIB for a Biostar Microtech board
ALSA: usb/audio.h: Fix field order
ALSA: fix jazz16 compile (udelay)
ALSA: hda: Use LPIB for Dell Latitude 131L
ALSA: hda - Build hda_eld into snd-hda-codec module
ALSA: hda - Support NVIDIA MCP89 and GT21x hdmi audio
ALSA: hda - Support max codecs to 8 for nvidia hda controller
ALSA: riptide: clean up while loop
ALSA: usbaudio - remove debug "SAMPLE BYTES" printk line
ALSA: timer - pass real event in snd_timer_notify1() to instance callback
ALSA: oxygen: change || to &&
ALSA: opti92x: use PnP data to select Master Control port
ASoC: fix ak4104 register array access
ASoC: soc_pcm_open: Add missing bailout tag
ALSA: usbaudio: Fix wrong bitrate for Creative Creative VF0470 Live Cam
ALSA: ua101: removing debugging code
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (220 commits)
USB: backlight, appledisplay: fix incomplete registration failure handling
USB: pl2303: remove unnecessary reset of usb_device in urbs
USB: ftdi_sio: remove obsolete check in unthrottle
USB: ftdi_sio: remove unused tx_bytes counter
USB: qcaux: driver for auxiliary serial ports on Qualcomm devices
USB: pl2303: initial TIOCGSERIAL support
USB: option: add Longcheer/Longsung vendor ID
USB: fix I2C API usage in ohci-pnx4008.
USB: usbmon: mask seconds properly in text API
USB: sisusbvga: no unnecessary GFP_ATOMIC
USB: storage: onetouch: unnecessary GFP_ATOMIC
USB: serial: ftdi: add CONTEC vendor and product id
USB: remove references to port->port.count from the serial drivers
USB: tty: Prune uses of tty_request_room in the USB layer
USB: tty: Add a function to insert a string of characters with the same flag
USB: don't read past config->interface[] if usb_control_msg() fails in usb_reset_configuration()
USB: tty: kill request_room for USB ACM class
USB: tty: sort out the request_room handling for whiteheat
USB: storage: fix misplaced parenthesis
USB: vstusb.c: removal of driver for Vernier Software & Technology, Inc., devices and spectrometers
...
This patch removes the vstusb driver and support from the Linux tree.
This driver provided support for Vernier Software & Technology devices
and spectrometers (Ocean Optics). This driver is being replaced by a
user space - libusb - implementation.
Signed-off-by: Jim Collar <jim.collar@eqware.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding vbus_pin_inverted so that the usb detect pin can be active high
or low depending on HW implementation also replaced the
gpio_get_value(udc->vbus_pin); with a call to vbus_is_present(udc); This
allows the driver to be loaded and save about 0,15W on the consumption.
Signed-off-by: Eirik Aanonsen <eaa@wprmedical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
after 2.6.34, those fields will be removed from
struct musb_hdrc_platform_data, it's expected
that other architectures are fixed by then.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some of the board might use external Vbus power supply on musb
interface which would require to program ULPI_BUSCONTROL register.
Adding 'extvbus' flag which can be set from such boards which will
be checked at musb driver files before programming ULPI_BUSCONTROL.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's really the wireless speed, so rename the thing to make
more sense. Based on a recommendation from David Vrabel
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices must be switched to a new mode to fully use them.
A reset would make them revert to the old mode. Therefore a reset
must not be used for error handling with such devices.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The notifier will be used to communicate usb events
to other drivers like the charger chip.
This can be used as source of information to kick
usb charger detection as described by the USB
Battery Charging Specification 1.1 and/or to
pass bMaxPower field of selected usb_configuration
to charger chip in order to use that information
as input current on the charging profile
setup.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (214 commits)
omap2: Initialize Menelaus and MMC for N8X0
AM3517 EVM: correct typo - tca6416 mispelt as tca6516
AM3517 EVM: Enable I2C support
AM35x: Enable OMAP_MUX in defconfig
AM35x: Add missing GPIO mux config for EHCI port
Zoom3: Defconfig update
omap: i2c: Fix muxing for command line enabled bus
OMAP4: clock: Remove clock hacks from timer-gp.c
OMAP4: clock: Add dummy clock nodes for interface clocks
OMAP4: clock: Rename leaf clock nodes to end with a _ick or _fck
OMAP2+ clock: revise omap2_clk_{disable,enable}()
OMAP2/3 clock: combine OMAP2 & 3 boot-time MPU rate change code
OMAP clockdomain: if no autodeps exist, don't try to add or remove them
OMAP hwmod: add hwmod class support
OMAP hwmod: convert header files with static allocations into C files
OMAP hwmod: convert hwmod to use hardware clock names rather than clkdev dev+con
OMAP clock: add omap_clk_get_by_name() for use by OMAP hwmod core code
OMAP3: clock: add capability to change rate of dpll4_m5_ck_3630
OMAP4 clock: drop the ALWAYS_ENABLED clock flag
OMAP clock: drop RATE_FIXED clock flag
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1341 commits)
virtio_net: remove forgotten assignment
be2net: fix tx completion polling
sis190: fix cable detect via link status poll
net: fix protocol sk_buff field
bridge: Fix build error when IGMP_SNOOPING is not enabled
bnx2x: Tx barriers and locks
scm: Only support SCM_RIGHTS on unix domain sockets.
vhost-net: restart tx poll on sk_sndbuf full
vhost: fix get_user_pages_fast error handling
vhost: initialize log eventfd context pointer
vhost: logging thinko fix
wireless: convert to use netdev_for_each_mc_addr
ethtool: do not set some flags, if others failed
ipoib: returned back addrlen check for mc addresses
netlink: Adding inode field to /proc/net/netlink
axnet_cs: add new id
bridge: Make IGMP snooping depend upon BRIDGE.
bridge: Add multicast count/interval sysfs entries
bridge: Add hash elasticity/max sysfs entries
bridge: Add multicast_snooping sysfs toggle
...
Trivial conflicts in Documentation/feature-removal-schedule.txt
Use the definitions from linux/usb/audio.h all over the ALSA USB audio
driver and add some missing definitions there as well.
Use the endpoint attribute macros from linux/usb/ch9 and remove the own
things from sound/usb/usbaudio.h.
Now things are also nicely prefixed which makes understanding the code
easier.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds some definitions for audio class v2.
Unfortunately, the UNIT types PROCESSING_UNIT and EXTENSION_UNIT have
different numerical representations in both standards, so there is need
for a _V1 add-on now. usbmixer.c is changed accordingly.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In preparation of support for v2.0 audio class, use the structs from
linux/usb/audio.h and add some new ones to describe the fields that are
actually parsed by the descriptor decoders.
Also, factor out code from usb_create_streams(). This makes it easier to
adopt the new iteration logic needed for v2.0.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pass board specific data for MUSB (like interface_type,
mode etc) from board file by defining board
specific structure.
Each board file can define this structure based on
its requirement and pass this information to the
driver.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Gupta Ajay Kumar <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add empty functions for usb_nop_xceiv_register()
and usb_nop_xceiv_unregister() in otg.h so that
these functions can be called even when
CONFIG_NOP_USB_XCEIV is not enabled.
It allows to remove ifdef's from board file.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These macros are too similar to the dev_<level> equivalents
but take a usbnet * argument. Convert them to the recently
introduced netdev_<level> macros and remove the old macros.
The old macros had "\n" appended to the format string.
Add the "\n" to the converted uses.
Some existing uses of the dev<foo> macros in cdc_eem.c
probably mistakenly had trailing "\n". No "\n" added there.
Fix net1080 this/other log message inversion.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The USB serial code was a new user of the kfifo API, and it was missed
when porting things to the new kfifo API.
Please make the write_fifo in place. Here is my patch to fix the
regression and full ported version.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Reported-and-tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (58 commits)
tty: split the lock up a bit further
tty: Move the leader test in disassociate
tty: Push the bkl down a bit in the hangup code
tty: Push the lock down further into the ldisc code
tty: push the BKL down into the handlers a bit
tty: moxa: split open lock
tty: moxa: Kill the use of lock_kernel
tty: moxa: Fix modem op locking
tty: moxa: Kill off the throttle method
tty: moxa: Locking clean up
tty: moxa: rework the locking a bit
tty: moxa: Use more tty_port ops
tty: isicom: fix deadlock on shutdown
tty: mxser: Use the new locking rules to fix setserial properly
tty: mxser: use the tty_port_open method
tty: isicom: sort out the board init logic
tty: isicom: switch to the new tty_port_open helper
tty: tty_port: Add a kref object to the tty port
tty: istallion: tty port open/close methods
tty: stallion: Convert to the tty_port_open/close methods
...
The tty port has a port mutex used for all the port related locking so we
don't need the one in the USB serial layer any more.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a minimal generic driver for ULPI connected transceivers,
using the OTG framework functions recently introduced.
The driver got a table to match the ULPI chips, which currently only has
one entry for NXP's ISP 1504 transceiver.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Heikki Krogerus <ext-heikki.krogerus@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for OTG transceivers directly connected to the ULPI
interface. In particular, the following details are added
- a struct for low level io functions (read/write)
- a priv field to be used as 'viewport' by low level access functions
- an (*init) and (*shutdown) callbacks, along with static inline helpers
- a (*set_vbus) callback to switch the port power on and off
- a flags field for per-transceiver settings
- some defines for the flags bitmask to configure platform specific
details
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Heikki Krogerus <ext-heikki.krogerus@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Control requests targeted at an endpoint (that is sent to EP0 but
specifying the target endpoint address in wIndex) are dispatched to the
current configuration's setup callback, requiring all gadget drivers to
dispatch the requests to the correct function driver.
To avoid this, record which endpoints are used by each function in the
composite driver SET CONFIGURATION handler and dispatch requests
targeted at endpoints to the correct function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"Definition" is misspelled "defintion" in several comments; this
patch fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Using remote wakeup and delayed transmission to allow
online device to go into usb autosuspend.
Minimal alternate support for devices that don't support
remote wakeup.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some usbnet drivers update link state while others do not due to
hardware limitations. Add a flag to distinguish those that do, and
set the link down initially for their devices.
This is intended to fix this bug: http://bugs.debian.org/444043
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch (as1295) fixes a recently-added bug in the USB serial core.
If certain kinds of errors occur during probing, the core may call a
serial driver's release method without previously calling the attach
method. This causes some drivers (io_ti in particular) to perform an
invalid memory access.
The patch adds a new flag to keep track of whether or not attach has
been called.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jean-Denis Girard <jd.girard@sysnux.pf>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for usbnet based devices like CDC-Ether to indicate that they
are actually mobile broadband devices. In that case use wwan%d as default
interface name.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some EHCI usb debug controllers, the EHCI debug device will fail to
be seen after a port reset, after a warm reset. Two options exist to
get the device to initialize correctly.
Option 1 is to unplug and plug in the device.
Option 2 is to use the EHCI port test to get the usb debug device to
start talking again. At that point the debug controller port reset
will succeed.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
CC: dbrownell@users.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the EHCI debug port is initialized and in use, the EHCI host
controller driver must follow two rules.
1) If the EHCI host driver issues a controller reset, the debug
controller driver re-initialization must get called after the reset
is completed.
2) The EHCI host driver should ignore any requests to the physical
EHCI debug port when the EHCI debug port is in use.
The code to check for the debug port was moved from ehci_pci_reinit()
to ehci_pci_setup because it must get called prior to ehci_reset()
which will clear the debug port registers.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: dbrownell@users.sourceforge.net
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements several changes:
1) Improve the capability to debug the dbgp driver
The dbgp_ehci_status() was added in a number of places to report
the critical ehci registers to diagnose the cause of a failure of
the ehci-dbgp driver.
2) Capability to survive the host controller initialization
The dbgp_external_startup(), dbgp_not_safe, and dbgp_phys_port were
added so as to allow the ehci-dbgp to re-initialize after the ehci
host controller is reset by the standard host controller driver.
This same routine is common for the early startup or
re-initialization.
This resulted in the need to move some of the initialization code
out of the __init section because the ehci driver has the
possibility to be loaded later on as a kernel module.
3) Stability improvements for device initialization
The device enumeration from 0 to 127 has the possibility to fail
the first time after a warm reset on some older EHCI debug
controllers. The enumeration will be tried up to 3 times to
account for this failure case.
The dbg_wait_until_complete() was changed to wait up to 250 ms
before failing which only comes into play during device
initialization. The maximum delay will never get hit during the
course of normal operation of the driver, unless the device got
unplugged or there was a ehci controller failure, in which case the
dbgp device driver will shut itself down.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: dbrownell@users.sourceforge.net
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the dbgp early printk driver in advance of refactoring and adding
new code, so the changes to this code are tracked separately from the
move of the code.
The drivers/usb/early directory will be the location of the current
and future early usb code for driving usb devices prior initializing
the standard interrupt driven USB drivers.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When do_output_char() attempts to write a carriage return/line feed sequence,
it first checks to see how much buffer room is available. If there are at least
two characters free, it will write the carriage return/line feed with two calls
to tty_put_char(). It calls the tty_operation functions write() for devices that
don't support the tty_operations function put_char(). If the USB generic serial
device's write URB is not in use, it will return the buffer size when asked how
much room is available. The write() of the carriage return will cause it to mark
the write URB busy, so the subsequent write() of the line feed will be ignored.
This patch uses the kfifo infrastructure to implement a write FIFO that
accurately returns the amount of space available in the buffer.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
include/linux/usb/audio.h is exported to userspace,
so part of this file that is for internal kernel
usage need to be guarded with ifdef __KERNEL__.
This way make headers_install will stript it out.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Platform device support was merged earlier, but support for boards to
customize the devflags aspect of the controller was not. We want this on
Blackfin systems to control the bus width, but might as well expose all of
the fields while we're at it.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Intel Moorestown EHCI controller supports non-standard HOSTPCx register
extension. This register controls the LPM behaviour and controls the behaviour
of each USB port.
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Alek Du <alek.du@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Those functions are used only used to fill the set/get members of
usb_audio_control. It doesn't make much sense to inline them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
linux/usb/audio.h is a public header file that includes definitions
exported to userspace. To avoid namespace clashes, prefix all macro
definitions with UAC_. Existing macros and structures prefixed with
USB_AC_ and USB_AS_ are renamed for consistency.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB_SUBCLASS_VENDOR_SPEC is common to several USB classes and as such belongs
to usb/ch9.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
And use the new definitions in the USB Audio Class gadget driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Usbnet framework assumes USB hardware doesn't handle zero length
packets, but SMSC LAN95xx requires these to be sent for correct
operation.
This patch fixes an easily reproducible tx lockup when sending a frame
that results in exactly 512 bytes in a USB transmission (e.g. a UDP
frame with 458 data bytes, due to IP headers and our USB headers). It
adds an extra flag to usbnet for the hardware driver to indicate that
it can handle and requires the zero length packets.
This patch should not affect other usbnet users, please also consider
for -stable.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various drivers have hacks to mangle termios structures. This stems from
the fact there is no nice setup hook for configuring the termios settings
when the port is created
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
And indeed none of them use it. Clean this up as it will make moving to a
standard open method rather easier.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To make UVC constants accessible by a future UVC gadget driver, move them from
drivers/media/video/uvc/uvcvideo.h to include/linux/usb/video.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add rx queue pausing to usbnet. This is needed by rndis_wlan so that it can
control rx queue and prevent received packets from being send forward before
rndis_wlan receives and handles 'media connect'-indication. Without this
establishing WPA connections is hard and fail often.
[v2] - removed unneeded use of skb_clone
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add handling for 802.11 specific rndis indications.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow rndis_wlan to see all indications. Currently rndis_host lets rndis_wlan to
know about link state changes only, but there is whole set of other
802.11-specific indications that rndis_wlan should handle properly. So rename
link_change() to indication() and convert rndis_wlan to use it.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wlan devices freeze after running usbnet_stop several times. It appears
that firmware freezes in state where it does not respond to any RNDIS commands
and device have to be physically unplugged/replugged. This patch lets
minidrivers to disable unlink_urbs on usbnet_stop through new info flag.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert the m66592-udc driver to use the on_chip flag
from platform data to enable on chip behaviour instead
of relying on CONFIG_SUPERH_BUILT_IN_M66592 ugliness.
This makes the code cleaner and also allows us to support
both external and internal m66592 with the same kernel.
It also makes the Kconfig part more future proof since
we with this patch can add support for new processors
with on-chip m66592 without modifying the Kconfig.
The patch adds a m66592 header file for platform data
and ties in platform data to the existing m66592 devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move r8a66597 hardware register definitions from the host
controller header file to the platform data header file.
With this change in place we can easily share register
definitions between the host controller driver and a future
gadget driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the r8a66597-hcd driver to use the on_chip flag
from platform data to enable on chip behaviour instead
of relying on CONFIG_SUPERH_ON_CHIP_R8A66597 ugliness.
This makes the code cleaner and also allows us to support
both external and internal r8a66597 with the same kernel.
It also makes the Kconfig part more future proof since
we with this patch can add support for new processors
with on-chip r8a66597 without modifying the Kconfig.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reverts commit 453f775588.
The driver should not have been accepted as the MSRT code is not
in the main kernel yet, which this depends on.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Hao Wu <hao.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The sysrq code acquired a kref leak. Fix it by passing the tty separately
from the caller (thus effectively using the callers kref which all the
callers hold anyway)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow minidriver to know that netdev has stopped. This is to let
wireless turn off radio when usbnet dev is stopped.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that nothing uses the private stats structure we can remove it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Differentiate between SuperSpeed endpoint companion descriptor and the
wireless USB endpoint companion descriptor. Make all structure names for
this descriptor have "ss" (SuperSpeed) in them. David Vrabel asked for
this change in http://marc.info/?l=linux-usb&m=124091465109367&w=2
Reported-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is
supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used
to extend the bus protocol to allow more packets to be sent to an endpoint per
"microframe". The word microframe was removed from the USB 3.0 specification
because the host controller does not send Start Of Frame (SOF) symbols down the
USB 3.0 wires.
The descriptor defines a bMaxBurst field, which indicates the number of packets
of wMaxPacketSize that a SuperSpeed device can send or recieve in a service
interval. All non-control endpoints may set this value as high as 16 packets
(bMaxBurst = 15).
The descriptor also allows isochronous endpoints to further specify that they
can send and receive multiple bursts per service interval. The bmAttributes
allows them to specify a "Mult" of up to 3 (bmAttributes = 2).
Bulk endpoints use bmAttributes to report the number of "Streams" they support.
This was an extension of the endpoint pipe concept to allow multiple mass
storage device commands to be outstanding for one bulk endpoint at a time. This
should allow USB 3.0 mass storage devices to support SCSI command queueing.
Bulk endpoints can say they support up to 2^16 (65,536) streams.
The information in the endpoint companion descriptor must be stored with the
other device, config, interface, and endpoint descriptors because the host
controller needs to access them quickly, and we need to install some default
values if a SuperSpeed device doesn't provide an endpoint companion descriptor.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify the USB core to handle the new USB 3.0 speed, "SuperSpeed". This
is 5.0 Gbps (wire speed). There are probably more places that check for
speed that I've missed.
SuperSpeed devices have a 512 byte endpoint 0 max packet size. This shows
up as a bMaxPacketSize0 set to 0x09 (see table 9-8 of the USB 3.0 bus
spec).
xHCI spec says that the xHC can handle intervals up to 2^15 microframes. That
might change when real silicon becomes available.
Add FIXME note for SuperSpeed isochronous endpoints. They can transmit up
to 16 packets in one "burst" before they wait for an acknowledgment of the
packets. They can do up to 3 bursts per microframe (determined by the
mult value in the endpoint companion descriptor). The xHCI driver doesn't
have support for isoc yet, so fix this later.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Description:
This driver is used for Intel Langwell* USB OTG controller in Intel
Moorestown* platform. It tries to implement host/device role switch
according to OTG spec. The actual hsot and device functions are
accomplished in modified EHCI driver and Intel Langwell USB OTG client
controller driver.
* Langwell and Moorestown are names used in development. They are not
approved official name.
Note:
This patch is the first version Intel Langwell USB OTG Transceiver
driver. The development is not finished, and the bug fixing is on going
for some hardware and software issues. The main purpose of this
submission is for code view.
Supported features:
- Data-line Pulsing SRP
- Support HNP to switch roles
- PCI D0/D3 power management support
Known issues:
- HNP is only tested with another Moorestown platform.
- PCI D0/D3 power management support is not fully tested.
- VBus Pulsing SRP is not support in current version.
Signed-off-by: Hao Wu <hao.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Intel Langwell USB Device Controller is a High-Speed USB OTG device
controller in Intel Moorestown platform. It can work in OTG device mode
with Intel Langwell USB OTG transceiver driver as well as device-only
mode. The number of programmable endpoints is different through
controller revision.
NOTE:
This patch is the first version Intel Langwell USB OTG device controller
driver. The bug fixing is on going for some hardware and software
issues. Intel Langwell USB OTG transceiver driver and EHCI driver
patches will be submitted later.
Supported features:
- USB OTG protocol support with Intel Langwell USB OTG transceiver
driver (turn on CONFIG_USB_LANGWELL_OTG)
- Support control, bulk, interrupt and isochronous endpoints
(isochronous not tested)
- PCI D0/D3 power management support
- Link Power Management (LPM) support
Tested gadget drivers:
- g_file_storage
- g_ether
- g_zero
The passed tests:
- g_file_storage: USBCV Chapter 9 tests
- g_file_storage: USBCV MSC tests
- g_file_storage: from/to host files copying
- g_ether: ping, ftp and scp files from/to host
- Hotplug, with and without hubs
Known issues:
- g_ether: failed part of USBCV chap9 tests
- LPM support not fully tested
TODO:
- g_ether: pass all USBCV chap9 tests
- g_zero: pass usbtest tests
- Stress tests on different gadget drivers
- On-chip private SRAM caching support
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1254) splits up the shutdown method of usb_serial_driver
into a disconnect and a release method.
The problem is that the usb-serial core was calling shutdown during
disconnect handling, but drivers didn't expect it to be called until
after all the open file references had been closed. The result was an
oops when the close method tried to use memory that had been
deallocated by shutdown.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1253) prevents the usb-serial core from calling a
driver's port_probe and port_remove methods more than once per port.
It also removes some unnecessary try_module_get() calls and adds a
missing port_remove method call in a failure path.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CPU/board specific parameters (PLL clock, vif etc...) can be set
by platform_data instead of module_param.
v2: remove irq_sense member in platform_data because it can OR in
IRQF_TRIGGER_LOW or IRQF_TRIGGER_FALLING against IORESOURCE_IRQ in
the struct resource.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Reviewed-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb_debug driver was modified to implement serial break handling
by using a "magic" data packet comprised of the sequence:
0x00 0xff 0x01 0xfe 0x00 0xfe 0x01 0xff
When the tty layer requests a serial break the usb_debug driver sends
the magic packet. On the receiving side the magic packet is thrown
away or a sysrq is activated depending on what kernel .config options
have been set.
The generic serial driver was modified as well as the usb serial
headers to generically implement sysrq processing in the same way the
non usb uart based drivers implement the sysrq handling. This will
allow other usb serial devices to implement sysrq handling as desired.
The new usb serial functions are named similarly and implemented
similarly to the uart functions as follows:
usb_serial_handle_break <-> uart_handle_break
usb_serial_handle_sysrq_char <-> uart_handle_sysrq_char
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb_debug driver, when used as the console, will always fail to
insert the carriage return and new line sequence as well as randomly
drop console output. This is a result of only having the single
write_urb and that the tty layer will have a lock that prevents the
processing of the back to back urb requests.
The solution is to allow more than one urb to be outstanding and have
a slightly deeper transmit queue. The idea and some code is borrowed
from the ftdi_sio usb driver.
The generic usb serial driver was modified so as to allow the classic
method of 1 write urb, or a multi write urb scheme with N allowed
outstanding urbs where N is controlled by max_in_flight_urbs. When
max_in_flight_urbs in a "struct usb_serial_driver" is non zero the
multi write urb scheme will be used.
The size of 4000 was selected for the usb_debug driver so that the
driver lowers possibility of losing the queued console messages during
the kernel startup.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mark internal struct members as /* private: */ so that kernel-doc
won't produce warnings about missing descriptions for them.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The NOP OTG transceiver driver needs to be usable from modules.
Make sure its symbols are always accessible at both compile and
link time, and make sure the device instance is allocated from
the heap so that device lifetime rules are obeyed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allows us to clean stuff up, but is probably also going to cause
some app breakage with buggy apps as we now implement proper POSIX behaviour
for USB ports matching all the other ports. This does also mean other apps
that break on USB will now work properly.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
e1000: fix virtualization bug
bonding: fix alb mode locking regression
Bluetooth: Fix issue with sysfs handling for connections
usbnet: CDC EEM support (v5)
tcp: Fix tcp_prequeue() to get correct rto_min value
ehea: fix invalid pointer access
ne2k-pci: Do not register device until initialized.
Subject: [PATCH] br2684: restore net_dev initialization
net: Only store high 16 bits of kernel generated filter priorities
virtio_net: Fix function name typo
virtio_net: Cleanup command queue scatterlist usage
bonding: correct the cleanup in bond_create()
virtio: add missing include to virtio_net.h
smsc95xx: add support for LAN9512 and LAN9514
smsc95xx: configure LED outputs
netconsole: take care of NETDEV_UNREGISTER event
xt_socket: checks for the state of nf_conntrack
bonding: bond_slave_info_query() fix
cxgb3: fixing gcc 4.4 compiler warning: suggest parentheses around operand of ‘!’
netfilter: use likely() in xt_info_rdlock_bh()
...
This introduces a CDC Ethernet Emulation Model (EEM) host side
driver to support USB EEM devices.
EEM is different from the Ethernet Control Model (ECM) currently
supported by the "CDC Ethernet" driver. One key difference is
that it doesn't require of USB interface alternate settings to
manage interface state; some maldesigned hardware can't handle
that part of USB. It also avoids a separate USB interface for
control and status updates.
[ dbrownell@users.sourceforge.net: fix skb leaks, add rx packet
checks, improve fault handling, EEM conformance updates, cleanup ]
Signed-off-by: Omar Laazimani <omar.oberthur@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #ifndef to musb header file to prevent multiple inclusions.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
because of using the same function get_ethernet_addr as cdc_ether.c
i export usbnet_get_ethernet_addr from usbnet and fixed cdc_ether
(suggested by Oliver Neukum).
Signed-off-by: Peter Holik <peter@holik.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Acked-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Address one open question in the composite gadget framework:
Yes, we should have device-level suspend/resume callbacks
in addition to the function-level ones. We have at least one
scenario (with gadget zero in OTG test mode) that's awkward
to handle without it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just noticed this during a grep, figured I might as well send it in.
From: D.J. Capelis <dev@capelis.dj>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To permit a userspace application to associate with WUSB devices
using numeric association, control transfers to unauthenticated WUSB
devices must be allowed.
This requires that wusbcore correctly sets the device state to
UNAUTHENTICATED, DEFAULT and ADDRESS and that control transfers can be
performed to UNAUTHENTICATED devices.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
NOP transceiver is used by all the usb transceiver which are mostly
autonomous and doesn't require any programming or which are built
into the usb ip itself.NOP transceiver only allocates the memory
for struct xceiv and calls otg_set_transceiver() so function call
to otg_get_transceiver() will return a valid transceiver.
NOP transceiver device should be registered by calling
usb_nop_xceiv_register() from platform files.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch introduces a flag into the usb serial layer to tell drivers
that their URBs are killed due to suspension. That is necessary to let
drivers know whether they should report an error back.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Hi Greg,
this is for 2.6.30. Patches to use this in drivers are under development.
Regards
Oliver
The functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_is_isoc_in(epd)
usb_endpoint_is_isoc_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
are moved from include/linux/usb.h to include/linux/usb/ch9.h.
include/linux/usb/ch9.h makes more sense for these functions because they
only depend on constants that are defined in this file.
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Call usb_gadget_vbus_connect() and ...disconnect() from a
workqueue rather than from an irq handler, allowing msleep()
calls in vbus_session. Update kerneldoc to match.
[ dbrownell@users.sourceforge.net: more kerneldoc updates ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Apparently the Configuration and Interface strings aren't used as
often as the Vendor, Product, and Serial strings. In at least one
device (a Saitek Cyborg Gold 3D joystick), attempts to read the
Configuration string cause the device to stop responding to Control
requests.
This patch (as1226) adds a quirks flag, telling the kernel not to
read a device's Configuration or Interface strings, together with a
new quirk for the offending joystick.
Reported-by: Melchior FRANZ <melchior.franz@gmail.com>
Tested-by: Melchior FRANZ <melchior.franz@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> [2.6.28 and 2.6.29, nothing earlier]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use net_device_ops for usbnet device, and export for use
by other derived drivers.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cpu_to_le32 directly as it handles constant folding now, replace direct
uses of __constant_cpu_to_{endian} as well.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix the following 'make headers_check' warning:
usr/include/linux/usb/gadgetfs.h:21: include of <linux/types.h> is preferred over <asm/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warning:
usr/include/linux/usb/cdc.h:50: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Improve usbnet's devdbg to always type-check diagnostic arguments,
like dev_dbg (device.h). This makes no change to the resulting size of
usbnet modules.
This patch also removes an #ifdef DEBUG directive from rndis_wlan so
it's devdbg statements are always type-checked at compile time.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Russell King points out, calling put_device(otg_transceiver->dev)
directly in driver cleanup paths makes assumptions about otg_transceiver
internals.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
gpio_vbus provides simple GPIO VBUS sensing for peripheral
controllers with an internal transceiver.
Optionally, a second GPIO can be used to control D+ pullup.
It also interfaces with the regulator framework to limit charging
currents when powered via USB. gpio_vbus requests the regulator
supplying "vbus_draw" and can enable/disable it or limit its
current depending on USB state.
[dbrownell@users.sourceforge.net: use drivers/otg, cleanups ]
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also a trivial annotation in rh.c for:
drivers/usb/wusbcore/rh.c:366:9: warning: incorrect type in assignment (different base types)
drivers/usb/wusbcore/rh.c:366:9: expected unsigned short [unsigned] [short] [usertype] <noident>
drivers/usb/wusbcore/rh.c:366:9: got restricted __le16 [usertype] <noident>
drivers/usb/wusbcore/rh.c:367:9: warning: incorrect type in assignment (different base types)
drivers/usb/wusbcore/rh.c:367:9: expected unsigned short [unsigned] [short] [usertype] <noident>
drivers/usb/wusbcore/rh.c:367:9: got restricted __le16 [usertype] <noident>
Association types annotation fixes piles of warnings similar to:
drivers/usb/wusbcore/cbaf.c:238:30: warning: incorrect type in initializer (different base types)
drivers/usb/wusbcore/cbaf.c:238:30: expected restricted __le16 [usertype] id
drivers/usb/wusbcore/cbaf.c:238:30: got int
drivers/usb/wusbcore/cbaf.c:238:30: warning: incorrect type in initializer (different base types)
drivers/usb/wusbcore/cbaf.c:238:30: expected restricted __le16 [usertype] len
drivers/usb/wusbcore/cbaf.c:238:30: got int
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a comment and clarifies the documentation about the
endianness of descriptors. The current policy is that descriptors will
be little-endian at the API even on big-endian systems; however the
/proc/bus/usb API predates this policy and presents descriptors with
some multibyte fields byte-swapped.
Signed-off-by: Phil Endecott <usb_endian_patch@chezphil.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When stopping the WUSB channel the host should send Channel Stop IEs giving
the WUSB Channel Time of the last MMC. Both WHCI and HWA hosts provide a
channel stop command for this.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
This patch adds the vstusb driver to the drivers/usb/misc directory.
This driver provides support for Vernier Software & Technology
spectrometers, all made by Ocean Optics. The driver provides both IOCTL
and read()/write() methods for sending raw data to spectrometers across
the bulk channel. Each method allows for a configured timeout.
From: Stephen Ware <stephen.ware@eqware.net>
Signed-off-by: Dennis O'Brien <dennis.obrien@eqware.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes a minor typo in the comments for usb_set_serial_data.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch introduces a new f_obex.c function driver.
It allows userspace obex servers to use usb as transport layer
for their messages.
[ dbrownell@users.sourceforge.net: various fixes and cleanups ]
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a new mechanism to the composite gadget framework, letting
functions deactivate (and reactivate) themselves. Think of it
as a refcounted wrapper for the software pullup control.
A key example of why to use this mechanism involves functions that
require a userspace daemon. Those functions shuld use this new
mechanism to prevent the gadget from enumerating until those daemons
are activated. Without this mechanism, hosts would see devices that
malfunction until the relevant daemons start.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver was originaly written by Stefan Kopp, but massively
reworked by Greg for submission.
Thanks to Felipe Balbi <me@felipebalbi.com> for lots of work in cleaning
up this driver.
Thanks to Oliver Neukum <oliver@neukum.org> for reviewing previous
versions and pointing out problems.
Cc: Stefan Kopp <stefan_kopp@agilent.com>
Cc: Marcel Janssen <korgull@home.nl>
Cc: Felipe Balbi <me@felipebalbi.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use platform_data to pass musb configuration-specific
details to musb driver.
This patch will prevent that other platforms selecting
HAVE_CLK and enabling musb won't break tree building.
The other parts of it will come when linux-omap merge
up more omap2/3 board-files.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for MUSB and TUSB controllers
integrated into omap2430 and davinci. It also adds support
for external tusb6010 controller.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1121) fixes a bug in the USB serial core. When a device
is unregistered, the core will give back its minors -- even if the
device hasn't been assigned any!
The patch reserves the highest minor value (255) to mean that no minor
was assigned. It also removes some dead code and does a small style
fixup.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
prepare x86: usb debug port early console
move ehci struct def to linux/usrb/ehci_def.h from host/ehci.h
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: "Arjan van de Ven" <arjan@infradead.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Greg KH" <greg@kroah.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We want to use WARN() as a variant of WARN_ON(), however a few drivers are
using WARN() internally. This patch renames these to WARNING() to avoid the
namespace clash. A few cases were defining but not using the thing, for those
cases I just deleted the definition.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Greg KH <greg@kroah.com>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
USB serial likes to use port->tty back pointers for the real work it does and
to do so without any actual locking. Unfortunately when you consider hangup
events, hangup/parallel reopen or even worse hangup followed by parallel close
events the tty->port and port->tty pointers are not guaranteed to be the same
as port->tty is the active tty while tty->port is the port the tty may or
may not still be attached to.
So rework the entire API to pass the tty struct. For console cases we need
to pass both for now. This shows up multiple drivers that immediately crash
with USB console some of which have been fixed in the process.
Longer term we need a proper tty as console abstraction
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1102) clarifies two points in the USB Gadget kerneldoc:
Request completion callbacks are always made with interrupts
disabled;
Device controllers may not support STALLing the status stage
of a control transfer after the data stage is over.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
General cleanup on ir-usb module. Introduced
a common header that could be used also on
usb gadget framework.
Lot's of cleanups and now using macros from the header
file.
Signed-off-by: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add <linux/usb/composite.h> interfaces for composite gadget drivers, and
basic implementation support behind it:
- struct usb_function ... groups one or more interfaces into a function
managed as one unit within a configuration, to which it's added by
usb_add_function().
- struct usb_configuration ... groups one or more such functions into
a configuration managed as one unit by a driver, to which it's added
by usb_add_config(). These operate at either high or full/low speeds
and at a given bMaxPower.
- struct usb_composite_driver ... groups one or more such configurations
into a gadget driver, which may be registered or unregistered.
- struct usb_composite_dev ... a usb_composite_driver manages this; it
wraps the usb_gadget exposed by the controller driver.
This also includes some basic kerneldoc.
How to use it (the short version): provide a usb_composite_driver with a
bind() that calls usb_add_config() for each of the needed configurations.
The configurations in turn have bind() calls, which will usb_add_function()
for each function required. Each function's bind() allocates resources
needed to perform its tasks, like endpoints; sometimes configurations will
allocate resources too.
Separate patches will convert most gadget drivers to this infrastructure.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Define three new descriptor manipulation utilities, for use when
setting up functions that may have multiple instances:
usb_copy_descriptors() to copy a vector of descriptors
usb_free_descriptors() to free the copy
usb_find_endpoint() to find a copied version
These will be used as follows. Functions will continue to have static
tables of descriptors they update, now used as __initdata templates.
When a function creates a new instance, it patches those tables with
relevant interface and string IDs, plus endpoint assignments. Then it
copies those morphed descriptors, associates the copies with the new
function instance, and records the endpoint descriptors to use when
activating the endpoints. When initialization is done, only the copies
remain in memory. The copies are freed on driver removal.
This ensures that each instance has descriptors which hold the right
instance-specific data. Two instances in the same configuration will
obviously never share the same interface IDs or use the same endpoints.
Instances in different configurations won't do so either, which means
this is slightly less memory-efficient in some cases.
This also includes a bugfix to the epautoconf code that shows up with
this usage model. It must replace the previous endpoint number when
updating the template descriptors, not just mask in a few more bits.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pass buffer length to rndis_command so that rndis_command can read full
response buffer from device instead of max CONTROL_BUFFER_SIZE bytes.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This will be used by the wireless usb code, as well as potentially other
USB code.
Originally based on some .c code written by Inaky Perez-Gonzalez
<inaky.perez-gonzalez@intel.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Gadget can tell controller driver to ignore Clear-Feature(HALT_ENDPOINT)
This API change enables future support for Bulk-Only Transport compliance
Signed-off-by: David Lopo <lopo.david@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch add the core driver for the c67x00 USB OTG controller. The core
driver is responsible for the platform bus binding and creating either
USB HCD or USB Gadget instances for each of the serial interface engines
on the chip.
This driver does not directly implement the HCD or gadget behaviours; it
just controls access to the chip.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This device descriptor was added by the recent USB Link Power Management (LPM)
ECN. It indicates whether the USB device supports LPM.
This descriptor is grouped under a Binary Device Object Store (BOS) descriptor.
Update the BOS comments to indicate any USB device (not just wireless USB
devices) can implement BOS descriptors.
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the unused check for num_interrupt and friends as well as remove
them from the header file because no usb-serial drivers no longer
reference them.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For the header files in include/linux/usb, add missing multiple
inclusion protection and standardize what's already there. The
apparent standards:
* macro name of __LINUX_USB_headerfile_H
* inclusion protection placed after leading comment block
* macro name added as a comment on the final #endif
* any obvious trivial whitespace cleanup associated with the above
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's a new PM-related change notice for the USB 2.0 specification
called "Link Power Management" (LPM). It defines a new "L1 Suspend"
state which resembles the current (L2) suspend state, except that it
can be entered and exited much more quickly. It should thus be more
useful for runtime PM, even though it doesn't mandate reduced power
draw from VBUS.
This patch provides the relevant #defines for usbcore. Actually
implementing these mechanisms requires host silicon that can generate
new USB packets, plus hubs handling some new requests and peripherals
which understand the new packets.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed by the wireless usb developers, and is part of the USB spec.
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The atmel_usba_udc driver is being used by several platforms and arches
(avr32 and at91 ATM), and each platform may have different endpoint
settings.
The patch below moves the endpoint declarations into the platform
data and make the necessary adjustments for AVR32 (improved by
Haavard Skinnemoen <hskinnemoen@atmel.com>).
Signed-off-by: Stelian Pop <stelian@popies.net>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch (as1057) fixes a problem with the X-Rite/Gretag-Macbeth
Eye-One Pro display colorimeter; the device crashes when it receives a
Set-Interface request. A new quirk (USB_QUIRK_NO_SET_INTF) is
introduced and a quirks entry is created for this device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the header file gadget.h isn't being exported to userspace,
there seems to be little point having a __KERNEL__ proprocessor check.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the header file g_printer.h doesn't depend on __KERNEL__,
there's no need to unifdef it in the Kbuild file.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a problem where the mos7720 driver will make io to a device from
which it has been logically disconnected. It does so by introducing a flag by
which the generic usb serial code can signal the subdrivers their
disconnection and appropriate locking.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Given that none of the referenced header files test the proprocessor
conditional __KERNEL__, there's no point "unifdef"fing them.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a usb serial adapter is used as console, the usb serial console
driver bumps the open_count on the port struct used but doesn't attach
a real tty to it (only a fake one temporaly). If this port is opened later
using the regular character device interface, the open method won't
initialize the port, which is the expected, and will receive a brand new
tty struct created by tty layer, which will be stored in port->tty.
When the last close is issued, open_count won't be 0 because of the
console usage and the port->tty will still contain the old tty value. This
is the last ttyUSB<n> close so the allocated tty will be freed by the
tty layer. The usb_serial and usb_serial_port are still in use by the
console, so port_free() won't be called (serial_close() ->
usb_serial_put() -> destroy_serial() -> port_free()), so the scheduled
work (port->work, usb_serial_port_work()) will still run. And
usb_serial_port_work() does:
(...)
tty = port->tty;
if (!tty)
return;
tty_wakeup(tty);
which causes (manually copied):
Faulting instruction address: 0x6b6b6b68
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT PowerMac
Modules linked in: binfmt_misc ipv6 nfs lockd nfs_acl sunrpc dm_snapshot dm_mirror dm_mod hfsplus uinput ams input_polldev genrtc cpufreq_powersave i2c_powermac therm_adt746x snd_aoa_codec_tas snd_aoa_fabric_layout snd_aoa joydev snd_aoa_i2sbus snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_page_alloc pmac_zilog serial_core evdev ide_cd cdrom snd appletouch soundcore snd_aoa_soundbus bcm43xx firmware_class usbhid ieee80211softmac ff_memless firewire_ohci firewire_core ieee80211 ieee80211_crypt crc_itu_t sungem sungem_phy uninorth_agp agpart ssb
NIP: 6b6b6b68 LR: c01b2108 CTR: 6b6b6b6b
REGS: c106de80 TRAP: 0400 Not tainted (2.6.24-rc2)
MSR: 40009032 <EE,ME,IR,DR> CR: 82004024 XER: 00000000
TASK = c106b4c0[5] 'events/0' THREAD: c106c000
GPR00: 6b6b6b6b c106df30 c106b4c0 c2d613a0 00009032 00000001 00001a00 00000001
GPR08: 00000008 00000000 00000000 c106c000 42004028 00000000 016ffbe0 0171a724
GPR16: 016ffcf4 00240e24 00240e70 016fee68 016ff9a4 c03046c4 c0327f50 c03046fc
GPR24: c106b6b9 c106b4c0 c101d610 c106c000 c02160fc c1eac1dc c2d613ac c2d613a0
NIP [6b6b6b68] 0x6b6b6b68
LR [c01b2108] tty_wakeup+0x6c/0x9c
Call Trace:
[c106df30] [c01b20e8] tty_wakeup+0x4c/0x9c (unreliable)
[c106df40] [c0216138] usb_serial_port_work+0x3c/0x78
[c106df50] [c00432e8] run_workqueue+0xc4/0x15c
[c106df90] [c0043798] worker_thread+0xa0/0x124
[c106dfd0] [c0048224] kthread+0x48/0x84
[c106dff0] [c00129bc] kernel_thread+0x44/0x60
Instruction dump:
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
Slab corruption: size-2048 start=c2d613a0, len=2048
Redzone: 0x9f911029d74e35b/0x9f911029d74e35b.
Last user: [<c01b16d8>](release_one_tty+0xbc/0xf4)
050: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
Prev obj: start=c2d60b88, len=2048
Redzone: 0x9f911029d74e35b/0x9f911029d74e35b.
Last user: [<c00f30ec>](show_stat+0x410/0x428)
000: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
010: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
This patch avoids this, clearing port->tty considering if the port is
used as serial console or not
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
G_PRINTER: Adds a USB printer gadget driver for use in printer firmware.
This adds a USB printer gadget driver for use in printer firmware.
The printer gadget channels data between the USB host and a userspace
program driving the print engine. The user space program reads and
writes the device file /dev/g_printer to receive or send printer data.
It can use ioctl calls to the device file to get or set printer status.
Signed-off-by: Craig W. Nadler <craig@nadler.us>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move headers usbnet.h and rndis_host.h to include/linux/usb and fix includes
for drivers/net/usb modules. Headers are moved because rndis_wlan will be
outside drivers/net/usb in drivers/net/wireless and yet need these headers.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix USB docbook warnings.
Warning(linux-2.6.23-git8//include/linux/usb/gadget.h:487): No description found for parameter 'g'
Warning(linux-2.6.23-git8//include/linux/usb/gadget.h:506): No description found for parameter 'g'
Warning(linux-2.6.23-git8//drivers/usb/core/hub.c:1416): No description found for parameter 'usb_dev'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as997) fixes a bug in the USB serial core. The core needs
to pay attention to drivers' requirements regarding the number and
type of endpoints a device has.
At the same time, the patch changes the NUM_DONT_CARE constant (which
is stored in a single-byte field) from -1 to a safer, unsigned value.
It also improves the kerneldoc for several fields in the
usb_serial_driver structure.
Finally, the patch replaces a list_for_each() with list_for_each_entry().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move <linux/usb_gadget.h> to <linux/usb/gadget.h>, reducing
some of the clutter in the main include directory.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as995) cleans up the remains of the former NO_AUTOSUSPEND
quirk. Since autosuspend is disabled by default, we will let
userspace worry about which devices can safely be suspended. Thus the
lengthy series of quirk entries is no longer needed, and neither is
the quirk ID. I suppose someone might eventually run across a hub
that can't be suspended; let's ignore the possibility for now.
The patch also cleans up the hasty way in which autosuspend gets
disabled. Setting udev->autosuspend_delay to -1 wasn't quite right,
because the value is always supposed to be a multiple of HZ. It's
better to leave the delay value alone and set autosuspend_disabled,
which is what the quirk routine used to do.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure gadgetfs userspace interface is properly exported:
- Move <linux/usb_gadgetfs.h> to <linux/usb/gadgetfs.h>;
- Export it using Kbuild;
- Add an #include guard;
- Correct some internal documentation;
- Update struct layout so it's the same on 32/64 bit kernels.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as888) adds a new USB device quirk for devices which are
unable to resume correctly. By using the new code added for the
USB-persist facility, it is a simple matter to reset these devices
instead of resuming them. To get things kicked off, a quirk entry is
added for the Philips PSC805.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this implements generic support for suspend/resume for usb serial.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor doc update to <linux/usb/ch9.h> ... say where USB_DT_CS_* came
from and update the definitions to match how they're derived there.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this adds another structure for CDC devices to cdc.h.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a blacklist to the USB core to handle some autosuspend and
string issues that devices have.
Originally written by Oliver, but hacked up a lot by Greg.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add argumentation in defense of using __attribute__((packed)) in USB
descriptors authored by Dave Brownell. Necessary as in some cases it
seems superfluous.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ioctl is commented out for now, until we verify some userspace
application issues.
Cc: Christian Lucht <lucht@codemercs.com>
Cc: Robert Marquardt <marquardt@codemercs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this is Joris' fixes reshuffelled and features renamed as David requested.
- acm_set_control is not mandatory, honour that
- throtteling is reset upon open
- throtteling is read consistently when processing input data
Signed-off-by: Joris van Rantwijk <jorispubl@xs4all.nl>
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb: descriptor structures have to be packed
Many of the Wireless USB decriptors added to usb_ch9.h don't have the
__attribute__((packed)) tag, and thus, they don't reflect the wire
size. This patch fixes that.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I added two fields to struct usb_serial_port to keep track of the
throttle state. Other usb-serial drivers typically use private data for
such things, but the generic driver can not really do that because some
of its code is also used by other drivers (which may have their own
private data needs).
As it is, I am not sure that this patch is useful in all scenarios.
It is certainly helpful for low-bandwidth devices that can hold their
data in response to throttling. But for devices that pump data in
real-time as fast as possible (webcam, A/D converter, etc), throttling
may actually cause more data loss.
From: Joris van Rantwijk <jorispubl@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thanks to Johannes Hölzl <johannes.hoelzl@gmx.de> for fixing a few
things and getting it all working properly.
This adds support for dynamic usb ids to the usb serial core. The file
"new_id" will show up under the usb serial driver, not the usb driver
associated with the usb-serial driver (yeah, it can be a bit confusing
at first glance...)
This patch also modifies the USB core to allow the usb-serial core to
reuse much of the dynamic id logic.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Johannes Hölzl <johannes.hoelzl@gmx.de>
This moves <linux/usb_ch9.h> to <linux/usb/ch9.h> to reduce some of the
clutter of usb header files.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the grungy swap all the occurrences in the right places patch that
goes with the updates. At this point we have the same functionality as
before (except that sgttyb() returns speeds not zero) and are ready to
begin turning new stuff on providing nobody reports lots of bugs
If you are a tty driver author converting an out of tree driver the only
impact should be termios->ktermios name changes for the speed/property
setting functions from your upper layers.
If you are implementing your own TCGETS function before then your driver
was broken already and its about to get a whole lot more painful for you so
please fix it 8)
Also fill in c_ispeed/ospeed on init for most devices, although the current
code will do this for you anyway but I'd like eventually to lose that extra
paranoia
[akpm@osdl.org: bluetooth fix]
[mp3@de.ibm.com: sclp fix]
[mp3@de.ibm.com: warning fix for tty3270]
[hugh@veritas.com: fix tty_ioctl powerpc build]
[jdike@addtoit.com: uml: fix ->set_termios declaration]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
This driver is glue between the USB gadget interface
and the ALSA MIDI interface. It allows us to appear
as a MIDI Streaming device to a host system on the
other end of a USB cable.
This includes linux/usb/audio.h and linux/usb/midi.h
containing definitions from the relevant USB specifications
for USB audio and USB MIDI devices.
The following changes have been made since the first RFC
posting:
* Bug fixes to endpoint handling.
* Workaround for USB_REQ_SET_CONFIGURATION handling,
not understood yet.
* Added SND and SND_RAWMIDI dependencies in Kconfig.
* Moved usb_audio.h and usb_midi.h to usb/*.h
* Added module parameters for ALSA card index and id.
* Added module parameters for USB descriptor IDs and strings.
* Removed some unneeded stuff inherited from zero.c, more to go.
* Provide DECLARE_* macros for the variable-length structs.
* Use kmalloc instead of usb_ep_alloc_buffer.
* Limit source to 80 columns.
* Return actual error code instead of -ENOMEM in a few places.
Signed-off-by: Ben Williamson <ben.williamson@greyinnovation.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
