SDK7786 supports connecting either slot3 or 4 to the same PCIe port by
way of FPGA muxing. By default the vertical slot 3 on the baseboard is
enabled, so this adds in a command line option for forcibly enabling the
slot 4 edge connector.
If nothing has been specified on the command line, we fall back to
reading the resistor values for card presence to figure out where to
route the port to.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This first converts the PMB locking over to raw spinlocks, and secondly
fixes up a nested locking issue that was triggering lockdep early on:
swapper/0 is trying to acquire lock:
(&pmbe->lock){......}, at: [<806be9bc>] pmb_init+0xf4/0x4dc
but task is already holding lock:
(&pmbe->lock){......}, at: [<806be98e>] pmb_init+0xc6/0x4dc
other info that might help us debug this:
1 lock held by swapper/0:
#0: (&pmbe->lock){......}, at: [<806be98e>] pmb_init+0xc6/0x4dc
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The sdk7786 FPGA supports a number of user settable input switches that
are otherwise unused. This wires up a dummy gpio chip for the switch bank
to simply expose them to userspace.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently this is uninitialized in the architecture code, so it's
artificlally capped to the default initialization value. Set it up at
registration time.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We need to round memory regions correctly -- specifically, we need to
round reserved region in the more expansive direction (lower limit
down, upper limit up) whereas usable memory regions need to be rounded
in the more restrictive direction (lower limit up, upper limit down).
This introduces two set of inlines:
memblock_region_memory_base_pfn()
memblock_region_memory_end_pfn()
memblock_region_reserved_base_pfn()
memblock_region_reserved_end_pfn()
Although they are antisymmetric (and therefore are technically
duplicates) the use of the different inlines explicitly documents the
programmer's intention.
The lack of proper rounding caused a bug on ARM, which was then found
to also affect other architectures.
Reported-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4CB4CDFD.4020105@kernel.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The PMCAT location has conveniently moved on newer SH-X3 parts, special
case this for now with a note. This will probably want to be redone in a
less visually offensive way when/if more information becomes available.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sparse irq sets up NR_IRQS_LEGACY irq descriptors and archs then go
ahead and allocate more.
Use the unused return value of arch_probe_nr_irqs() to let the
architecture return the number of early allocations. Fix up all users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Now that we've got a generic perf-events based oprofile backend we might
as well make use of it seeing as SH doesn't do anything special with its
oprofile backend. Also introduce a new CONFIG_HW_PERF_EVENTS symbol so
that we can fallback to using the timer interrupt for oprofile if the
CPU doesn't support perf events.
Also, to avoid a section mismatch warning we need to annotate
oprofile_arch_exit() with an __exit marker.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Introduce perf_pmu_name() helper function that returns the name of the
pmu. This gives us a generic way to get the name of a pmu regardless of
how an architecture identifies it internally.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Checks for (irq < 0) and (ilsel < 0) didn't make sense since they were
unsigned. Made them signed.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The number of counters for the registered pmu is needed in a few places
so provide a helper function that returns this number.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Fix the IRQ flag handling naming. In linux/irqflags.h under one configuration,
it maps:
local_irq_enable() -> raw_local_irq_enable()
local_irq_disable() -> raw_local_irq_disable()
local_irq_save() -> raw_local_irq_save()
...
and under the other configuration, it maps:
raw_local_irq_enable() -> local_irq_enable()
raw_local_irq_disable() -> local_irq_disable()
raw_local_irq_save() -> local_irq_save()
...
This is quite confusing. There should be one set of names expected of the
arch, and this should be wrapped to give another set of names that are expected
by users of this facility.
Change this to have the arch provide:
flags = arch_local_save_flags()
flags = arch_local_irq_save()
arch_local_irq_restore(flags)
arch_local_irq_disable()
arch_local_irq_enable()
arch_irqs_disabled_flags(flags)
arch_irqs_disabled()
arch_safe_halt()
Then linux/irqflags.h wraps these to provide:
raw_local_save_flags(flags)
raw_local_irq_save(flags)
raw_local_irq_restore(flags)
raw_local_irq_disable()
raw_local_irq_enable()
raw_irqs_disabled_flags(flags)
raw_irqs_disabled()
raw_safe_halt()
with type checking on the flags 'arguments', and then wraps those to provide:
local_save_flags(flags)
local_irq_save(flags)
local_irq_restore(flags)
local_irq_disable()
local_irq_enable()
irqs_disabled_flags(flags)
irqs_disabled()
safe_halt()
with tracing included if enabled.
The arch functions can now all be inline functions rather than some of them
having to be macros.
Signed-off-by: David Howells <dhowells@redhat.com> [X86, FRV, MN10300]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> [Tile]
Signed-off-by: Michal Simek <monstr@monstr.eu> [Microblaze]
Tested-by: Catalin Marinas <catalin.marinas@arm.com> [ARM]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> [AVR]
Acked-by: Tony Luck <tony.luck@intel.com> [IA-64]
Acked-by: Hirokazu Takata <takata@linux-m32r.org> [M32R]
Acked-by: Greg Ungerer <gerg@uclinux.org> [M68K/M68KNOMMU]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [MIPS]
Acked-by: Kyle McMartin <kyle@mcmartin.ca> [PA-RISC]
Acked-by: Paul Mackerras <paulus@samba.org> [PowerPC]
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [S390]
Acked-by: Chen Liqin <liqin.chen@sunplusct.com> [Score]
Acked-by: Matt Fleming <matt@console-pimps.org> [SH]
Acked-by: David S. Miller <davem@davemloft.net> [Sparc]
Acked-by: Chris Zankel <chris@zankel.net> [Xtensa]
Reviewed-by: Richard Henderson <rth@twiddle.net> [Alpha]
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp> [H8300]
Cc: starvik@axis.com [CRIS]
Cc: jesper.nilsson@axis.com [CRIS]
Cc: linux-cris-kernel@axis.com
Add missing consts to the sys_execve() declaration which result in the
following error:
arch/sh/kernel/process_32.c:303: error: conflicting types for 'sys_execve'
/warthog/nfs/linux-2.6-fscache/arch/sh/include/asm/syscalls_32.h:24: error: previous declaration of 'sys_execve' was here
Signed-off-by: David Howells <dhowells@redhat.com>
SH-3 lacks an MMUCR_TI definition for global TLB flushes. As SH-3 parts
lack a split TLB, the same global flush behaviour is accomplished
through the flush bit, which just happens to be the same as on SH-4.
This fixes up the build for all SH-3 MMU parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix a compile breakage, caused by my own careless copy-paste.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The spinlock in traps_64.c is used without initialization.
This fixes it by declaring DEFINE_SPINLOCK() and makes the spinlock static
variable.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With all the recent module loading cleanups, we've minimized the code
that sits under module_mutex, fixing various deadlocks and making it
possible to do most of the module loading in parallel.
However, that whole conversion totally missed the rather obscure code
that adds a new module to the list for BUG() handling. That code was
doubly obscure because (a) the code itself lives in lib/bugs.c (for
dubious reasons) and (b) it gets called from the architecture-specific
"module_finalize()" rather than from generic code.
Calling it from arch-specific code makes no sense what-so-ever to begin
with, and is now actively wrong since that code isn't protected by the
module loading lock any more.
So this commit moves the "module_bug_{finalize,cleanup}()" calls away
from the arch-specific code, and into the generic code - and in the
process protects it with the module_mutex so that the list operations
are now safe.
Future fixups:
- move the module list handling code into kernel/module.c where it
belongs.
- get rid of 'module_bug_list' and just use the regular list of modules
(called 'modules' - imagine that) that we already create and maintain
for other reasons.
Reported-and-tested-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SH7786 is the big user for subgroup splitting, mostly for the PCIe block,
but those will follow later. For now we simply split up SCIF1, as used by
the serial console on SDK7786 and others.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Many interrupts that share a single mask source but are on different
hardware vectors will have an associated register tied to an INTEVT that
denotes the precise cause for the interrupt exception being triggered.
This introduces the concept of IRQ subgroups in the intc core, where
a virtual IRQ map is constructed for each of the pre-defined cause bits,
and a higher level chained handler takes control of the parent INTEVT.
This enables CPUs with heavily muxed IRQ vectors (especially across
disjoint blocks) to break things out in to a series of managed chained
handlers while being able to dynamically lookup and adopt the IRQs
created for them.
This is largely an opt-in interface, requiring CPUs to manually submit
IRQs for subgroup splitting, in addition to providing identifiers in
their enum maps that can be used for lazy lookup via the radix tree.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
At the moment ILSEL blows up with a BUG when aliased sets are handed in,
but as the enable call is able to hand back errors we opt for that path
instead. None of the ILSEL peripherals are vital to the board's
operation, so trapping a BUG is a bit excessive.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds gpio-keys mappings for the button matrix on the baseboard,
now that we have support for the pin controller.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds trivial support for the GPIOs implemented through the baseboard
CPLD, used for driving the button matrix.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
As non-PFC chips are added that may support IRQs, pass through to the
generic helper instead of triggering the WARN_ON().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some controllers will need to be initialized lazily due to pinmux
constraints, while others may simply have no need to be brought online if
there are no backing devices for them attached. In this case it's still
necessary to be able to reserve their hardware vector map before dynamic
IRQs get a hold of them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH-X3 proto CPU has all of the external IRQ and IRL pins muxed, make
sure that we're able to grab them before attempting to register their
respective IRQ controllers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds in support for GPIO/pinmux on the SH-X3 proto CPUs. This will
subsequently be used by the x3proto board.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds in hardware IRQ auto-distribution support for SH-X3 proto CPUs,
following the SH7786 support.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This shuffles some of the shared bits out of the 7786 code and in to a
shared SH-X3 support file. Presently just for userimask, but also a good
place for the IRQ balancing wrappers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the SH kernel to keep SR.BL set until the VBR
register has been initialized. Useful to allow boot
of the kernel even though exceptions are pending.
Without this patch there is a window of time when
exceptions such as NMI are enabled but no exception
handlers are installed.
This patch modifies both the zImage loader and the
actual kernel to boot with BL=1, but the zImage
loader is modfied in such a way that the init_sr
value is unchanged to not break the zImage loader
provided by kexec.
Tested on sh7724 Ecovec and on the SH4AL-DSP core
included in sh7372.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
kfree() in clkdev_drop() function should actually be called with an address of
a struct clk_lookup_alloc object, and not struct clk_lookup, as presently done.
This just happens to work, because "struct clk_lookup cl" is the first
member in struct clk_lookup_alloc.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
While sh previously had its own debugfs root, there now exists a
common arch_debugfs_dir prototype, so we switch everything over to
that. Presumably once more architectures start making use of this
we'll be able to just kill off the stub kdebugfs wrapper.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This copies the pci_config_lock idea from x86 over, allowing us to kill
off a couple of existing private locks. At the same time, these need to
be converted to raw spinlocks for -rt kernels, so we make that change at
the same time. This should make it easier for future parts to get the
locking right instead of inevitable ending up with lock type mismatches.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This gets each port handling its MSTP bit, as well as moving the PHY
clock management in to the clock framework.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some of the existing code is flipping between __raw_xxx() and
pci_{read,write}_reg(). As the latter are just wrappers for the former,
flip over to using them consistently.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently we error out if a link is disabled and simply drop the port
registration outright. This follows the PPC changes and simply reports on
the link state on boot, leaving the port registered, in order to more
easily deal with hotplug on future parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These settings are properly propagated by the hardware already, so
there's no need to bother with them manually.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH7786 PCIe is presently unable to enumerate itself in root complex
mode, and has no visibility through either type 0 or type 1 accesses,
despite having a mostly sensible extended config space for each port.
Attempts to generate type 0 or type 1 config cycles result in completer
aborts, so we're ultimately forced to use SuperHyway transactions
instead.
As each port has a single port <-> device mapping that resolves for any
PCI_SLOT definition, we simply hijack devfn 0 for the SuperHyway
transaction and bump up the devfn limit.
With enumeration of the root complex now possible, we also need to insert
an early fixup to hide the BARs from the kernel. With all of that done,
it's now possible to use the pcieport services with all of the PCIe
ports, which is the first step to power management support.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously these IDs were only used by one driver, so there was not much
need for having them generically defined. Now that this will no longer
hold true, move them over.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Recent ASoC changes unified all PCM names, fix the platform code to match.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The spec suggests waiting up to 500ms for the PHY to settle before
testing link state, but practice shows that 100ms is sufficient (this is
the delay value we also use on the other SH-4A PCI controllers, too).
This makes device detection much more reliable, although in the future it
should be a bit faster to simply serialize with a TLP IRQ.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The only BKL user in arch/sh protects a single bit,
so we can trivially replace it with test_and_set_bit.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
3f6da390 ("perf: Rework and fix the arch CPU-hotplug hooks") introduced
this breakage. sh_pmu_setup() is missing an opening curly brace.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20100913191729.GA6440@console-pimps.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that the rest of the socket calls are provided through their own
paths, do the same for sys_recvmmsg. It's unlikely we'll ever be able to
kill off the socketcall path, but this at least permits userspace to
gradually begin migrating.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Linux kernel already has socket syscalls that can be invoked
without the multiplexing sys_socketcall wrapper.
C library wrappers are ready to use them directly. It needs just
to define the missing syscall numbers and provide the related entries
into the syscalls table, like sh64 aleady does.
Signed-off-by: Francesco Rundo <francesco.rundo@st.com>
Signed-off-by: Carmelo Amoroso <carmelo.amoroso@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch modify x_plate_ohms to correct value for tsc2007 panel,
and removed un-necessary ts_get_pendown_state()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
As the help for the config option suggests, this option really shouldn't
be set by default for any recent distribution as it changes the layout
of sysfs. I spotted this while running debian when udev got very
confused by the sysfs layout and failed to create some device nodes.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is a preparation for HDMI hotplug support. This patch just moves all
platform defined video modes for the sh_mobile_lcdcfb driver to separate
arrays and switches all users to use element 0 of that array, so, this patch
doesn't introduce any functional changes and as such should not cause any
regressions.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Replace pmu::{enable,disable,start,stop,unthrottle} with
pmu::{add,del,start,stop}, all of which take a flags argument.
The new interface extends the capability to stop a counter while
keeping it scheduled on the PMU. We replace the throttled state with
the generic stopped state.
This also allows us to efficiently stop/start counters over certain
code paths (like IRQ handlers).
It also allows scheduling a counter without it starting, allowing for
a generic frozen state (useful for rotating stopped counters).
The stopped state is implemented in two different ways, depending on
how the architecture implemented the throttled state:
1) We disable the counter:
a) the pmu has per-counter enable bits, we flip that
b) we program a NOP event, preserving the counter state
2) We store the counter state and ignore all read/overflow events
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: paulus <paulus@samba.org>
Cc: stephane eranian <eranian@googlemail.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Lin Ming <ming.m.lin@intel.com>
Cc: Yanmin <yanmin_zhang@linux.intel.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: Michael Cree <mcree@orcon.net.nz>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since the current perf_disable() usage is only an optimization,
remove it for now. This eases the removal of the __weak
hw_perf_enable() interface.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: paulus <paulus@samba.org>
Cc: stephane eranian <eranian@googlemail.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Lin Ming <ming.m.lin@intel.com>
Cc: Yanmin <yanmin_zhang@linux.intel.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: Michael Cree <mcree@orcon.net.nz>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Simple registration interface for struct pmu, this provides the
infrastructure for removing all the weak functions.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: paulus <paulus@samba.org>
Cc: stephane eranian <eranian@googlemail.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Lin Ming <ming.m.lin@intel.com>
Cc: Yanmin <yanmin_zhang@linux.intel.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: Michael Cree <mcree@orcon.net.nz>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that the resource assignment issues are resolved, we can finally wire
up the small third memory window -- in the future we may reclaim this for
MSI.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
An IORESOURCE_IO was missing here, which meant that we weren't properly
establishing the I/O window for this particular slot. With this
corrected, cards with I/O BARs have them actually assigned and
accessible.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Certain memory windows are only available for 32-bit space, so skip over
these in 29-bit mode. This will severely restrict the amount of memory
that can be mapped, but since a boot loader bug makes booting in 29-bit
mode close to impossible anyways, everything is ok.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This bumps up the low address to match the physical memory windows for
SHway<->PCIe transfers. The previous implementation was banking on a 1:1
virt<->phys SHway mapping, which doesn't apply here.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7786 PCIe has 1 slot per port, but no specific restriction on function.
Relax the devfn restriction and look to the slot number instead when
configured as a root complex.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This brings the clocking and register setting in line with the somewhat
factually ambiguous specification.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This enables support for type 1 config space accesses on the SH7786
PCI controller. At the same time, add in some extra sanity checks for
controller asserted errors.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Store the kernel and user contexts from the generic layer instead
of archs, this gathers some repetitive code.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Borislav Petkov <bp@amd64.org>
- Most archs use one callchain buffer per cpu, except x86 that needs
to deal with NMIs. Provide a default perf_callchain_buffer()
implementation that x86 overrides.
- Centralize all the kernel/user regs handling and invoke new arch
handlers from there: perf_callchain_user() / perf_callchain_kernel()
That avoid all the user_mode(), current->mm checks and so...
- Invert some parameters in perf_callchain_*() helpers: entry to the
left, regs to the right, following the traditional (dst, src).
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Borislav Petkov <bp@amd64.org>
callchain_store() is the same on every archs, inline it in
perf_event.h and rename it to perf_callchain_store() to avoid
any collision.
This removes repetitive code.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Borislav Petkov <bp@amd64.org>
Drop the TASK_RUNNING test on user tasks for callchains as
this check doesn't seem to make any sense.
Also remove the tests for !current that is not supposed to
happen and current->pid as this should be handled at the
generic level, with exclude_idle attribute.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Borislav Petkov <bp@amd64.org>
Make do_execve() take a const filename pointer so that kernel_execve() compiles
correctly on ARM:
arch/arm/kernel/sys_arm.c:88: warning: passing argument 1 of 'do_execve' discards qualifiers from pointer target type
This also requires the argv and envp arguments to be consted twice, once for
the pointer array and once for the strings the array points to. This is
because do_execve() passes a pointer to the filename (now const) to
copy_strings_kernel(). A simpler alternative would be to cast the filename
pointer in do_execve() when it's passed to copy_strings_kernel().
do_execve() may not change any of the strings it is passed as part of the argv
or envp lists as they are some of them in .rodata, so marking these strings as
const should be fine.
Further kernel_execve() and sys_execve() need to be changed to match.
This has been test built on x86_64, frv, arm and mips.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes up the nommu build with a stub definition for
__flush_tlb_global(), now used by the reboot code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sys_execve() now takes a const pointer, so reflect this change where the
syscall is actually defined, too. Fixes up a build error due to prototype
mismatch.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When executing:
make ARCH=sh defconfig
kconfig segfaulted.
kconfig should obviously not segfault.
But this indicated a problem in the sh files which was
tracked down to a recursive dependency.
We select HAVE_HW_BREAKPOINT and in the following line
we use the same symbol in an expression.
Drop the conditional as it is of no use.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Mark arguments to certain system calls as being const where they should be but
aren't. The list includes:
(*) The filename arguments of various stat syscalls, execve(), various utimes
syscalls and some mount syscalls.
(*) The filename arguments of some syscall helpers relating to the above.
(*) The buffer argument of various write syscalls.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (226 commits)
ARM: 6323/1: cam60: don't use __init for cam60_spi_{flash_platform_data,partitions}
ARM: 6324/1: cam60: move cam60_spi_devices to .init.data
ARM: 6322/1: imx/pca100: Fix name of spi platform data
ARM: 6321/1: fix syntax error in main Kconfig file
ARM: 6297/1: move U300 timer to dynamic clock lookup
ARM: 6296/1: clock U300 intcon and timer properly
ARM: 6295/1: fix U300 apb_pclk split
ARM: 6306/1: fix inverted MMC card detect in U300
ARM: 6299/1: errata: TLBIASIDIS and TLBIMVAIS operations can broadcast a faulty ASID
ARM: 6294/1: etm: do a dummy read from OSSRR during initialization
ARM: 6292/1: coresight: add ETM management registers
ARM: 6288/1: ftrace: document mcount formats
ARM: 6287/1: ftrace: clean up mcount assembly indentation
ARM: 6286/1: fix Thumb-2 decompressor broken by "Auto calculate ZRELADDR"
ARM: 6281/1: video/imxfb.c: allow usage without BACKLIGHT_CLASS_DEVICE
ARM: 6280/1: imx: Fix build failure when including <mach/gpio.h> without <linux/spinlock.h>
ARM: S5PV210: Fix on missing s3c-sdhci card detection method for hsmmc3
ARM: S5P: Fix on missing S5P_DEV_FIMC in plat-s5p/Kconfig
ARM: S5PV210: Override FIMC driver name on Aquila board
ARM: S5PC100: enable FIMC on SMDKC100
...
Fix up conflicts in arch/arm/mach-{s5pc100,s5pv210}/cpu.c due to
different subsystem 'setname' calls, and trivial port types in
include/linux/serial_core.h
Architectures implement dma_is_consistent() in different ways (some
misinterpret the definition of API in DMA-API.txt). So it hasn't been so
useful for drivers. We have only one user of the API in tree. Unlikely
out-of-tree drivers use the API.
Even if we fix dma_is_consistent() in some architectures, it doesn't look
useful at all. It was invented long ago for some old systems that can't
allocate coherent memory at all. It's better to export only APIs that are
definitely necessary for drivers.
Let's remove this API.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dma_get_cache_alignment returns the minimum DMA alignment. Architectures
defines it as ARCH_DMA_MINALIGN (formally ARCH_KMALLOC_MINALIGN). So we
can unify dma_get_cache_alignment implementations.
Note that some architectures implement dma_get_cache_alignment wrongly.
dma_get_cache_alignment() should return the minimum DMA alignment. So
fully-coherent architectures should return 1. This patch also fixes this
issue.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now each architecture has the own dma_get_cache_alignment implementation.
dma_get_cache_alignment returns the minimum DMA alignment. Architectures
define it as ARCH_KMALLOC_MINALIGN (it's used to make sure that malloc'ed
buffer is DMA-safe; the buffer doesn't share a cache with the others). So
we can unify dma_get_cache_alignment implementations.
This patch:
dma_get_cache_alignment() needs to know if an architecture defines
ARCH_KMALLOC_MINALIGN or not (needs to know if architecture has DMA
alignment restriction). However, slab.h define ARCH_KMALLOC_MINALIGN if
architectures doesn't define it.
Let's rename ARCH_KMALLOC_MINALIGN to ARCH_DMA_MINALIGN.
ARCH_KMALLOC_MINALIGN is used only in the internals of slab/slob/slub
(except for crypto).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
xen-blkfront: fix missing out label
blkdev: fix blkdev_issue_zeroout return value
block: update request stacking methods to support discards
block: fix missing export of blk_types.h
writeback: fix bad _bh spinlock nesting
drbd: revert "delay probes", feature is being re-implemented differently
drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
drbd: Disable delay probes for the upcomming release
writeback: cleanup bdi_register
writeback: add new tracepoints
writeback: remove unnecessary init_timer call
writeback: optimize periodic bdi thread wakeups
writeback: prevent unnecessary bdi threads wakeups
writeback: move bdi threads exiting logic to the forker thread
writeback: restructure bdi forker loop a little
writeback: move last_active to bdi
writeback: do not remove bdi from bdi_list
writeback: simplify bdi code a little
writeback: do not lose wake-ups in bdi threads
...
Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
