acpi_mcfg_64bit_base_addr is used when CONFIG_PCI_MMCONFIG is enabled.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/power/cpu_32.c __save_processor_state calls read_cr4()
only a i486 CPU doesn't have the CR4 register. Trying to read it
produces an invalid opcode oops during suspend to disk.
Use the safe rc4 reading op instead. If the value to be written is
zero the write is skipped.
arch/x86/power/hibernate_asm_32.S
done: swapped the use of %eax and %ecx to use jecxz for
the zero test and jump over store to %cr4.
restore_image: s/%ecx/%eax/ to be consistent with done:
In addition to __save_processor_state, acpi_save_state_mem,
efi_call_phys_prelog, and efi_call_phys_epilog had checks added
(acpi restore was in assembly and already had a check for
non-zero). There were other reads and writes of CR4, but MCE and
virtualization shouldn't be executed on a i486 anyway.
Signed-off-by: David Fries <david@fries.net>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/kernel/acpi/sleep.c:24: warning: 'temp_stack' defined but not used
[ Sven Wegener <sven.wegener@stealer.net>: fix build bug ]
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
SGI UV will have MMCFG base addresses that are greater than 4GB (32 bits).
v2: Use CONFIG_RESOURCES_64BIT instead of CONFIG_X86_64.
v3: Create a flag, that is set by platform specific code,
to disable the > 4GB check.
Signed-off-by: John Keller <jpk@sgi.com>
Cc: jpk@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Replace previous instances of the cpumask_of_cpu_ptr* macros
with a the new (lvalue capable) generic cpumask_of_cpu().
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
ACPI defines a hardware signature. BIOS calculates the signature according to
hardware configure and if hardware changes while hibernated, the signature
will change. In that case, S4 resume should fail.
Still, there may be systems on which this mechanism does not work correctly,
so it is better to provide a workaround for them. For this reason, add a new
switch to the acpi_sleep= command line argument allowing one to disable
hardware signature checking.
[shaohua.li@intel.com: build fix]
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <Valdis.Kletnieks@vt.edu>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
NR_CPUS: Replace NR_CPUS in speedstep-centrino.c
cpumask: Provide a generic set of CPUMASK_ALLOC macros, FIXUP
NR_CPUS: Replace NR_CPUS in cpufreq userspace routines
NR_CPUS: Replace per_cpu(..., smp_processor_id()) with __get_cpu_var
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genapic_flat_64.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genx2apic_uv_x.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/proc.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/mcheck/mce_64.c
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c, fix
cpumask: Use optimized CPUMASK_ALLOC macros in the centrino_target
cpumask: Provide a generic set of CPUMASK_ALLOC macros
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c
cpumask: Optimize cpumask_of_cpu in kernel/time/tick-common.c
cpumask: Optimize cpumask_of_cpu in drivers/misc/sgi-xp/xpc_main.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/ldt.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/io_apic_64.c
cpumask: Replace cpumask_of_cpu with cpumask_of_cpu_ptr
Revert "cpumask: introduce new APIs"
cpumask: make for_each_cpu_mask a bit smaller
net: Pass reference to cpumask variable in net/sunrpc/svc.c
...
Fix up trivial conflicts in drivers/cpufreq/cpufreq.c manually
There are a couple of places where (P)Dprintk is used which is an old
compile time enabled printk wrapper. Convert it to the generic
pr_debug().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* This patch replaces the dangerous lvalue version of cpumask_of_cpu
with new cpumask_of_cpu_ptr macros. These are patterned after the
node_to_cpumask_ptr macros.
In general terms, if there is a cpumask_of_cpu_map[] then a pointer to
the cpumask_of_cpu_map[cpu] entry is used. The cpumask_of_cpu_map
is provided when there is a large NR_CPUS count, reducing
greatly the amount of code generated and stack space used for
cpumask_of_cpu(). The pointer to the cpumask_t value is needed for
calling set_cpus_allowed_ptr() to reduce the amount of stack space
needed to pass the cpumask_t value.
If there isn't a cpumask_of_cpu_map[], then a temporary variable is
declared and filled in with value from cpumask_of_cpu(cpu) as well as
a pointer variable pointing to this temporary variable. Afterwards,
the pointer is used to reference the cpumask value. The compiler
will optimize out the extra dereference through the pointer as well
as the stack space used for the pointer, resulting in identical code.
A good example of the orthogonal usages is in net/sunrpc/svc.c:
case SVC_POOL_PERCPU:
{
unsigned int cpu = m->pool_to[pidx];
cpumask_of_cpu_ptr(cpumask, cpu);
*oldmask = current->cpus_allowed;
set_cpus_allowed_ptr(current, cpumask);
return 1;
}
case SVC_POOL_PERNODE:
{
unsigned int node = m->pool_to[pidx];
node_to_cpumask_ptr(nodecpumask, node);
*oldmask = current->cpus_allowed;
set_cpus_allowed_ptr(current, nodecpumask);
return 1;
}
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge the GDT_ENTRY() macro between arch/x86/boot/pm.c and
arch/x86/kernel/acpi/sleep.c and put the new one in
<asm-x86/segment.h>.
While we're at it, correct the bitmasks for the limit and flags. The
new version relies on using ULL constants in order to cause type
promotion rather than explicit casts; this avoids having to include
<linux/types.h> in <asm-x86/segments.h>.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (72 commits)
Revert "x86/PCI: ACPI based PCI gap calculation"
PCI: remove unnecessary volatile in PCIe hotplug struct controller
x86/PCI: ACPI based PCI gap calculation
PCI: include linux/pm_wakeup.h for device_set_wakeup_capable
PCI PM: Fix pci_prepare_to_sleep
x86/PCI: Fix PCI config space for domains > 0
Fix acpi_pm_device_sleep_wake() by providing a stub for CONFIG_PM_SLEEP=n
PCI: Simplify PCI device PM code
PCI PM: Introduce pci_prepare_to_sleep and pci_back_from_sleep
PCI ACPI: Rework PCI handling of wake-up
ACPI: Introduce new device wakeup flag 'prepared'
ACPI: Introduce acpi_device_sleep_wake function
PCI: rework pci_set_power_state function to call platform first
PCI: Introduce platform_pci_power_manageable function
ACPI: Introduce acpi_bus_power_manageable function
PCI: make pci_name use dev_name
PCI: handle pci_name() being const
PCI: add stub for pci_set_consistent_dma_mask()
PCI: remove unused arch pcibios_update_resource() functions
PCI: fix pci_setup_device()'s sprinting into a const buffer
...
Fixed up conflicts in various files (arch/x86/kernel/setup_64.c,
arch/x86/pci/irq.c, arch/x86/pci/pci.h, drivers/acpi/sleep/main.c,
drivers/pci/pci.c, drivers/pci/pci.h, include/acpi/acpi_bus.h) from x86
and ACPI updates manually.
991528d734
(ACPI: Processor native C-states using MWAIT)
started passing C2C3_FFH to _PDC to tell the BIOS
that Linux supports MWAIT for deep C-states.
However, we should first double check with the hardware
that it actually supports MWAIT before potentially exposing
a BIOS bug of an MWAIT _CST on HW that doesn't support MWAIT.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Explain that we set up the descriptors for Big Real Mode, and why we
do so. In particular, one system that is known to fail without it is
the Lenovo X61.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The explanation for recent video BIOS suspend quirk failures is that
the VESA BIOS expects to be entered in Big Real Mode (*.limit = 0xffffffff)
instead of ordinary Real Mode (*.limit = 0xffff).
This patch changes the segment descriptors to Big Real Mode instead.
The segment descriptor registers (what Intel calls "segment cache") is
always active. The only thing that changes based on CR0.PE is how it is
*loaded* and the interpretation of the CS flags.
The segment descriptor registers contain of the following sub-registers:
selector (the "visible" part), base, limit and flags. In protected mode
or long mode, they are loaded from descriptors (or fs.base or gs.base can
be manipulated directly in long mode.) In real mode, the only thing
changed by a segment register load is the selector and the base, where the
base <- selector << 4. In particular, *the limit and the flags are not
changed*.
As far as the handling of the CS flags: a code segment cannot be writable
in protected mode, whereas it is "just another segment" in real mode, so
there is some kind of quirk that kicks in for this when CR0.PE <- 0. I'm
not sure if this is accomplished by actually changing the cs.flags register
or just changing the interpretation; it might be something that is
CPU-specific. In particular, the Transmeta CPUs had an explicit "CS is
writable if you're in real mode" override, so even if you had loaded CS
with an execute-only segment it'd be writable (but not readable!) on return
to real mode. I'm not at all sure if that is how other CPUs behave.
Signed-off-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that IRQ2 is never made available to the I/O APIC, there is no need
to special-case it and mask as a workaround for broken systems. Actually,
because of the former, mask_IO_APIC_irq(2) is a no-op already.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
also remove GET_APIC_ID when read_apic_id is used.
need to apply after
[PATCH] x86: mach_apicdef.h need to include before smp.h
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
x2apic support. Interrupt-remapping must be enabled before enabling x2apic,
this is needed to ensure that IO interrupts continue to work properly after the
cpu mode is changed to x2apic(which uses 32bit extended physical/cluster
apic id).
On systems where apicid's are > 255, BIOS can handover the control to OS in
x2apic mode. Or if the OS handover was in legacy xapic mode, check
if it is capable of x2apic mode. And if we succeed in enabling
Interrupt-remapping, then we can enable x2apic mode in the CPU.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We have two conflicting DMA-based quirks in there for the same set of
boxes (HP nx6325 and nx6125) and one of them actually breaks my box.
So remove the extra code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: =?iso-8859-1?q?T=F6r=F6k_Edwin?= <edwintorok@gmail.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when more than 4g memory is installed, don't map the big hole below 4g.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
and let 64-bit to fall back to use fixmap too.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/kernel/acpi/boot.c: In function ‘dmi_ignore_irq0_timer_override’:
arch/x86/kernel/acpi/boot.c:1443: error: implicit declaration of function ‘force_mask_ioapic_irq_2’
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The problems are that, with the ACPI vs timer overring issue _fixed_,
after using the box for some time (between several seconds and 1 hour, at
random) processes get very high CPU loads (once I've got X using 107% of
the CPU, for example) and the system becomes unresponsive, as though there
were interrupts lost or something similar.
Andreas Herrman reproduced similar problems:
> Ok, now I've reproduced the stability problem.
> - Using tip/master,
> - reverting e38502eb8aa82314d5ab0eba45f50e6790dadd88 and
> - applying your patch from this posting
> http://marc.info/?l=linux-kernel&m=121539354224562&w=4
>
> Starting X, firefox, gimp, tuxpaint and doing some drawing in tuxpaint
> results in a slow system. Drawing is almost not possible anymore --
> Selections of new colors, cursors etc. is performed with huge delay
> if it's performed at all.
>
> BTW, the code sets up timer IRQ as Virtual Wire IRQ:
>
> Jul 8 14:57:58 kodscha IO-APIC (apicid-pin) 2-22, 2-23 not connected.
> Jul 8 14:57:58 kodscha ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
> Jul 8 14:57:58 kodscha ...trying to set up timer as Virtual Wire IRQ... works.
>
> and both INT0 and INT2 of IOAPIC are masked:
>
> Jul 8 14:57:58 kodscha NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
> Jul 8 14:57:58 kodscha 00 000 1 0 0 0 0 0 0 00
> Jul 8 14:57:58 kodscha 01 003 0 0 0 0 0 1 1 31
> Jul 8 14:57:58 kodscha 02 003 1 0 0 0 0 0 0 30
>
> I've also seen strange CPU utilization -- with syslog-ng:
>
> top - 15:33:06 up 35 min, 4 users, load average: 1.70, 0.68, 0.37
> Tasks: 64 total, 4 running, 60 sleeping, 0 stopped, 0 zombie
> Cpu0 : 0.0%us,100.0%sy, 0.0%ni, 0.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st
> Cpu1 : 6.4%us, 87.2%sy, 0.0%ni, 5.8%id, 0.0%wa, 0.6%hi, 0.0%si, 0.0%st
> Mem: 895384k total, 283568k used, 611816k free, 35492k buffers
> Swap: 1959920k total, 0k used, 1959920k free, 163044k cached
>
> PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
> 4632 root 20 0 17216 800 580 S 104 0.1 0:34.22 syslog-ng
> 28505 root 20 0 205m 11m 4024 S 6 1.3 0:21.16 X
> 28518 root 20 0 56292 5652 4492 S 1 0.6 0:01.80 fluxbox
> 1 root 20 0 3724 608 508 S 0 0.1 0:00.36 init
>
> So far I have no clue why C1E-idle in conjunction with virtual wire
> mode causes this strange behaviour.
>
> ... and I start to think about the root cause of all this.
>
> I've performed similar tests under X with the IRQ0/INT0 configuration and
> I did not see above symptoms.
So lets fall back to the IRQ0/INT0 configuration on this box.
This basically restores the dont-use-the-lapic-timer exception mechanism
that was unconditional on this box prior commit 8750bf5 ("x86: add C1E
aware idle function").
Signed-off-by: Ingo Molnar <mingo@elte.hu>
if acpi=off, acpi=noirq and pci=noacpi, we need to disable apic.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/kernel/acpi/sleep.c: In function ‘acpi_save_state_mem':
arch/x86/kernel/acpi/sleep.c:75: error: ‘stack_start' undeclared (first use in this function)
arch/x86/kernel/acpi/sleep.c:75: error: (Each undeclared identifier is reported
only once
arch/x86/kernel/acpi/sleep.c:75: error: for each function it appears in.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
call x86_64's init_rsp stack_start, just as i386 does.
Put a zeroed stack segment for consistency. With this,
we can eliminate one ugly ifdef in smpboot.c.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some HP laptops have a problem with their DSDT reporting as
HP/SB400/10000, which includes some code which overrides all temperature
trip points to 16C if the INTIN2 input of the I/O APIC is enabled. This
input is incorrectly designated the ISA IRQ 0 via an interrupt source
override even though it is wired to the output of the master 8259A and
INTIN0 is not connected at all. So far two models have been identified,
namely nx6125 and nx6325.
Use a knob provided by the I/O APIC interrupt registration code to
abandon any attempts to route IRQ 0 through the I/O APIC for these
systems.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As discovered recently some systems exhibit problems when the 8254 timer
IRQ is routed through the I/O APIC. These problems do not affect the
timer IRQ itself and therefore cannot be detected when the correctness of
operation of the interrupt is verified in check_timer(). Therefore the
I/O APIC path of the timer IRQ has to be disabled entirely.
This is a change that lets platforms ask for the timer IRQ not to be
registered in the I/O APIC interrupt tables. The local APIC and ExtINTA
paths are unaffected. This request is only taken into account for ACPI
platforms as MP table systems seem unaffected so far.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
if the system doesn't have ioapic, we don't need to store entries for mptable
update
also let mp_config_acpi_gsi not call func in mpparse
so later could decouple mpparse with acpi more easily
Reported-by: Daniel Exner <dex@dragonslave.de>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Daniel Exner <dex@dragonslave.de>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so we don't get the same value multiple times.
also make mp_config_acpi_legacy_irqs more readable by moving assignments
together.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Daniel Exner reported IO-APIC enumeration breakage in linux-next.
Alexey Starikovskiy found out that it might be related to
commit 2944e16b25 "x86: update mptable".
use enable_update_mptable to decide if need check before add mp_irqs array.
Reported-by: Daniel Exner <webmaster@dragonslave.de>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some Dell laptops enter resume with apparent garbage in the segment
descriptor registers (almost certainly the result of a botched
transition from protected to real mode.) The only way to clean that
up is to enter protected mode ourselves and clean out the descriptor
registers.
This fixes resume on Dell XPS M1210 and Dell D620.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=10927
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: pm list <linux-pm@lists.linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
ACPI PM: Add possibility to change suspend sequence
There are some systems out there that don't work correctly with
our current suspend/hibernation code ordering. Provide a workaround
for these systems allowing them to pass 'acpi_sleep=old_ordering' in
the kernel command line so that it will use the pre-ACPI 2.0 ("old")
suspend code ordering.
Unfortunately, this requires us to add a platform hook to the
resuming of devices for recovering the platform in case one of the
device drivers' .suspend() routines returns error code. Namely,
ACPI 1.0 specifies that _PTS should be called before suspending
devices, but _WAK still should be called before resuming them in
order to undo the changes made by _PTS. However, if there is an
error during suspending devices, they are automatically resumed
without returning control to the PM core, so the _WAK has to be
called from within device_resume() in that cases.
The patch also reorders and refactors the ACPI suspend/hibernation
code to avoid duplication as far as reasonably possible.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
... so it could fall back to normal numa and we'd reduce the impact of the
NUMAQ subarch.
NUMAQ depends on GENERICARCH
also decouple genericarch numa from acpi.
also make it fall back to bigsmp if apicid > 8.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
for http://bugzilla.kernel.org/show_bug.cgi?id=10613
BIOS bug, APIC version is 0 for CPU#0! fixing up to 0x10. (tell your hw vendor)
v2: fix 64 bit compilation
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Gabriel C <nix.or.die@googlemail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
make mptable to be consistent with acpi routing, so we could:
1. kexec kernel with acpi=off
2. work around BIOSes where acpi routing is working, but mptable is
not right, so can use kernel/kexec to start other OSes that don't have
good acpi support.
command line: update_mptable
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Sitsofe Wheeler reported boot problems on linux-next.
It looks like the same issue as found by Soeren Sandman in 7575217f656a93,
"x86: initialize all fields of mp_irqs[mp_irq_entries]".
But his fix is also not complete, as dstapic is used before it assigned.
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Bisected-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit "x86: make config_irqsrc not MPspec specific" introduced some uses
of uninitialized fields in mp_config_acpi_legacy_irqs(). I need the
following patch to get sched-devel/master to boot.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
