arch/x86/kernel/sfi.c serves the dual-purpose of supporting the
SFI core with arch specific code, as well as a home for the
arch-specific code that uses SFI.
analogous to ACPI, drivers/sfi/Kconfig is pulled in by arch/x86/Kconfig
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org
AMI BIOS with low memory corruption was found on Intel DG45ID
board (Bug 13710). Add this board to the blacklist - in the
(somewhat optimistic) hope of future boards/BIOSes from Intel
not having this bug.
Also see:
http://bugzilla.kernel.org/show_bug.cgi?id=13736
Signed-off-by: Alexey Fisher <bug-track@fisher-privat.net>
Cc: ykzhao <yakui.zhao@intel.com>
Cc: alan@lxorguk.ukuu.org.uk
Cc: <stable@kernel.org>
LKML-Reference: <1247660169-4503-1-git-send-email-bug-track@fisher-privat.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The init_gbpages() function is conditionally called from
init_memory_mapping() function. There are two call-sites where
this 'after_bootmem' condition can be true: setup_arch() and
mem_init() via pci_iommu_alloc().
Therefore, it's safe to move the call to init_gbpages() to
setup_arch() as it's always called before mem_init().
This removes an after_bootmem use - paving the way to remove
all uses of that state variable.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <Pine.LNX.4.64.0906221731210.19474@melkki.cs.Helsinki.FI>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On a system where system memory (according e820) is not covered by
mtrr, mtrr_trim_memory converts a portion of memory to reserved, but
bootloader has already put the initrd in that range.
Thus, we need to have 64bit to use relocate_initrd too.
[ Impact: fix using initrd when mtrr_trim_memory happen ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (22 commits)
x86: fix system without memory on node0
x86, mm: Fix node_possible_map logic
mm, x86: remove MEMORY_HOTPLUG_RESERVE related code
x86: make sparse mem work in non-NUMA mode
x86: process.c, remove useless headers
x86: merge process.c a bit
x86: use sparse_memory_present_with_active_regions() on UMA
x86: unify 64-bit UMA and NUMA paging_init()
x86: Allow 1MB of slack between the e820 map and SRAT, not 4GB
x86: Sanity check the e820 against the SRAT table using e820 map only
x86: clean up and and print out initial max_pfn_mapped
x86/pci: remove rounding quirk from e820_setup_gap()
x86, e820, pci: reserve extra free space near end of RAM
x86: fix typo in address space documentation
x86: 46 bit physical address support on 64 bits
x86, mm: fault.c, use printk_once() in is_errata93()
x86: move per-cpu mmu_gathers to mm/init.c
x86: move max_pfn_mapped and max_low_pfn_mapped to setup.c
x86: unify noexec handling
x86: remove (null) in /sys kernel_page_tables
...
* 'x86-kbuild-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (46 commits)
x86, boot: add new generated files to the appropriate .gitignore files
x86, boot: correct the calculation of ZO_INIT_SIZE
x86-64: align __PHYSICAL_START, remove __KERNEL_ALIGN
x86, boot: correct sanity checks in boot/compressed/misc.c
x86: add extension fields for bootloader type and version
x86, defconfig: update kernel position parameters
x86, defconfig: update to current, no material changes
x86: make CONFIG_RELOCATABLE the default
x86: default CONFIG_PHYSICAL_START and CONFIG_PHYSICAL_ALIGN to 16 MB
x86: document new bzImage fields
x86, boot: make kernel_alignment adjustable; new bzImage fields
x86, boot: remove dead code from boot/compressed/head_*.S
x86, boot: use LOAD_PHYSICAL_ADDR on 64 bits
x86, boot: make symbols from the main vmlinux available
x86, boot: determine compressed code offset at compile time
x86, boot: use appropriate rep string for move and clear
x86, boot: zero EFLAGS on 32 bits
x86, boot: set up the decompression stack as early as possible
x86, boot: straighten out ranges to copy/zero in compressed/head*.S
x86, boot: stylistic cleanups for boot/compressed/head_64.S
...
Fixed trivial conflict in arch/x86/configs/x86_64_defconfig manually
A long ago, in days of yore, it all began with a god named Thor.
There were vikings and boats and some plans for a Linux kernel
header. Unfortunately, a single 8-bit field was used for bootloader
type and version. This has generally worked without *too* much pain,
but we're getting close to flat running out of ID fields.
Add extension fields for both type and version. The type will be
extended if it the old field is 0xE; the version is a simple MSB
extension.
Keep /proc/sys/kernel/bootloader_type containing
(type << 4) + (ver & 0xf) for backwards compatiblity, but also add
/proc/sys/kernel/bootloader_version which contains the full version
number.
[ Impact: new feature to support more bootloaders ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Do this so we can check the range that is mapped before
init_memory_mapping().
To be able to print out meaningful info, we first have to fix
64-bit to have max_pfn_mapped assigned before that call. This
also unifies the code-path a bit.
[ Impact: print more debug info, cleanup ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <49BF0978.40605@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch moves the max_pfn_mapped and max_low_pfn_mapped global
variables to kernel/setup.c where they're initialized.
[ Impact: cleanup ]
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
LKML-Reference: <1240923649.1982.21.camel@penberg-laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
In preparation for unifying irqinit_{32,64}.c, make
x86_quirk_pre_intr_init() local to irqinit_32.c.
Reviewed-by Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
It's unused, since about 1995. So remove all initialization of it in
preparation for actually removing the field.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Impact: new interface; remove hard-coded limit
Add RESERVE_BRK(name, size) macro to reserve space in the brk
area. This should be a conservative (ie, larger) estimate of
how much space might possibly be required from the brk area.
Any unused space will be freed, so there's no real downside
on making the reservation too large (within limits).
The name should be unique within a given file, and somewhat
descriptive.
The C definition of RESERVE_BRK() ends up being more complex than
one would expect to work around a cluster of gcc infelicities:
The first attempt was to simply try putting __section(.brk_reservation)
on a variable. This doesn't work because it ends up making it a
@progbits section, which gets actual space allocated in the vmlinux
executable.
The second attempt was to emit the space into a section using asm,
but gcc doesn't allow arguments to be passed to file-level asm()
statements, making it hard to pass in the size.
The final attempt is to wrap the asm() in a function to allow
it to have arguments, and put the function itself into the
.discard section, which vmlinux*.lds drops entirely from the
emitted vmlinux.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: use new interface instead of previous ad hoc implementation
Use extend_brk() to allocate memory for DMI rather than having an
ad-hoc allocator.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: use new interface instead of previous ad hoc implementation
Rather than having special purpose init_pg_table_start/end variables
to delimit the kernel pagetable built by head_32.S, just use the brk
mechanism to extend the bss for the new pagetable.
This patch removes init_pg_table_start/end and pg0, defines __brk_base
(which is page-aligned and immediately follows _end), initializes
the brk region to start there, and uses it for the 32-bit pagetable.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: build fix
The brk initialization functions were incorrectly located inside
an #ifdef CONFIG_VLK_DEV_INITRD block, causing the obvious build failure in
minimal configurations.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Impact: new interface
Add a brk()-like allocator which effectively extends the bss in order
to allow very early code to do dynamic allocations. This is better than
using statically allocated arrays for data in subsystems which may never
get used.
The space for brk allocations is in the bss ELF segment, so that the
space is mapped properly by the code which maps the kernel, and so
that bootloaders keep the space free rather than putting a ramdisk or
something into it.
The bss itself, delimited by __bss_stop, ends before the brk area
(__brk_base to __brk_limit). The kernel text, data and bss is reserved
up to __bss_stop.
Any brk-allocated data is reserved separately just before the kernel
pagetable is built, as that code allocates from unreserved spaces
in the e820 map, potentially allocating from any unused brk memory.
Ultimately any unused memory in the brk area is used in the general
kernel memory pool.
Initially the brk space is set to 1MB, which is probably much larger
than any user needs (the largest current user is i386 head_32.S's code
to build the pagetables to map the kernel, which can get fairly large
with a big kernel image and no PSE support). So long as the system
has sufficient memory for the bootloader to reserve the kernel+1MB brk,
there are no bad effects resulting from an over-large brk.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: cleanup, micro-optimization
Pre-initialize boot_cpu_data.x86_phys_bits to a reasonable default
to remove the use of system_state tests in __virt_addr_valid()
and __phys_addr().
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: reactivate DMI quirks on EFI hardware
DMI tables are loaded by EFI, so the dmi calls must happen after
efi_init() and not before.
Currently Apple hardware uses DMI to determine the framebuffer mappings
for efifb. Without DMI working you also have no video on MacBook Pro.
This patch resolves the DMI issue for EFI hardware (DMI is now properly
detected at boot), and additionally efifb now loads on Apple hardware
(i.e. video works).
Signed-off-by: Brian Maly <bmaly@redhat>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: ying.huang@intel.com
LKML-Reference: <49ADEDA3.1030406@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/setup.c | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
Impact: cleanup
that is only needed when CONFIG_X86_VSMP is defined with 64bit
also remove dead code about PCI, because CONFIG_X86_VSMP depends on PCI
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
x86_quirks->update_apic() calling looks crazy. so try to remove it:
1. every apic take wakeup_cpu member directly
2. separate es7000_apic to es7000_apic_cluster
3. use uv_wakeup_cpu directly
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Make x86_quirks support more transparent. The highlevel
methods are now named:
extern void x86_quirk_pre_intr_init(void);
extern void x86_quirk_intr_init(void);
extern void x86_quirk_trap_init(void);
extern void x86_quirk_pre_time_init(void);
extern void x86_quirk_time_init(void);
This makes it clear that if some platform extension has to
do something here that it is considered ... weird, and is
discouraged.
Also remove arch_hooks.h and move it into setup.h (and other
header files where appropriate).
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: remove dead code
Remove:
- pre_setup_arch_hook()
- mca_nmi_hook()
If needed they can be added back via an x86_quirk handler.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: build fix, cleanup
A couple of arch setup callbacks were mistakenly in apic_32.c, breaking
the build.
Also simplify the code a bit.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Now that all APIC code is consolidated there's nothing 'gen' about
apics anymore - so rename 'struct genapic' to 'struct apic'.
This shortens the code and is nicer to read as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
so could deselect x2apic
and INTR_REMAP will select x2apic
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With refactoring of wake_cpu macros the 32bit code in tip doesn't
execute generic_apic_probe if CONFIG_X86_32_NON_STANDARD is not set.
Even on a x86 STANDARD cpu we need to execute the generic_apic_probe
function, as we rely on this function to execute the update_genapic
quirk which initilizes apic->wakeup_cpu.
Failing to do so results in we making a call to a null function in do_boot_cpu.
The stack trace without the patch goes like this.
Booting processor 1 APIC 0x1 ip 0x6000
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<(null)>] (null)
*pdpt = 0000000000839001 *pde = 0000000000c97067 *pte = 0000000000000163
Oops: 0000 [#1] SMP
last sysfs file:
Modules linked in:
Pid: 1, comm: swapper Not tainted (2.6.29-rc4-tip #18) VMware Virtual Platform
EIP: 0062:[<00000000>] EFLAGS: 00010293 CPU: 0
EIP is at 0x0
EAX: 00000001 EBX: 00006000 ECX: c077ed00 EDX: 00006000
ESI: 00000001 EDI: 00000001 EBP: ef04cf40 ESP: ef04cf1c
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 006a
Process swapper (pid: 1, ti=ef04c000 task=ef050000 task.ti=ef04c000)
Stack:
c0644e52 00000000 ef04cf24 ef04cf24 c064468d c0886dc0 00000000 c0702aea
ef055480 00000001 00000101 dead4ead ffffffff ffffffff c08af530 00000000
c0709715 ef04cf60 ef04cf60 00000001 00000000 00000000 dead4ead ffffffff
Call Trace:
[<c0644e52>] ? native_cpu_up+0x2de/0x45b
[<c064468d>] ? do_fork_idle+0x0/0x19
[<c0645c5e>] ? _cpu_up+0x88/0xe8
[<c0645d20>] ? cpu_up+0x42/0x4e
[<c07e7462>] ? kernel_init+0x99/0x14b
[<c07e73c9>] ? kernel_init+0x0/0x14b
[<c040375f>] ? kernel_thread_helper+0x7/0x10
Code: Bad EIP value.
EIP: [<00000000>] 0x0 SS:ESP 006a:ef04cf1c
I think we should call generic_apic_probe unconditionally for 32 bit now.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
just like 64 bit switch from flat logical APIC messages to
flat physical mode automatically.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
X86_GENERICARCH is a misnomer - it contains non-PC 32-bit architectures
that are not included in the default build.
Rename it to X86_32_NON_STANDARD.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
x86/Voyager had this Kconfig quirk:
config X86_FIND_SMP_CONFIG
def_bool y
depends on X86_MPPARSE || X86_VOYAGER
Which splits off the find_smp_config() callback into a build-time quirk.
Voyager should use the existing x86_quirks.mach_find_smp_config() callback
to introduce SMP-config quirks. NUMAQ-32 and VISWS already use this.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
x86/Voyager can boot on non-zero processors. While that can probably
be fixed by properly remapping the physical CPU IDs, keep boot_cpu_id
for now for easier transition - and expand it to all of x86.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The x86/Voyager subarch used to have this distinction between
'x86 SMP support' and 'Voyager SMP support':
config X86_SMP
bool
depends on SMP && ((X86_32 && !X86_VOYAGER) || X86_64)
This is a pointless distinction - Voyager can (and already does) use
smp_ops to implement various SMP quirks it has - and it can be extended
more to cover all the specialities of Voyager.
So remove this complication in the Kconfig space.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We are getting rid of subarchitecture support - move the hook files
to asm/. (These are now stale and should be replaced with more explicit
runtime mechanisms - but the transition is simpler this way.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rename genapic-> to apic-> references because in a future chagne we'll
open-code all the indirect calls (instead of obscuring them via macros),
so we want this reference to be as short as possible.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, sparseirq: clean up Kconfig entry
x86: turn CONFIG_SPARSE_IRQ off by default
sparseirq: fix numa_migrate_irq_desc dependency and comments
sparseirq: add kernel-doc notation for new member in irq_desc, -v2
locking, irq: enclose irq_desc_lock_class in CONFIG_LOCKDEP
sparseirq, xen: make sure irq_desc is allocated for interrupts
sparseirq: fix !SMP building, #2
x86, sparseirq: move irq_desc according to smp_affinity, v7
proc: enclose desc variable of show_stat() in CONFIG_SPARSE_IRQ
sparse irqs: add irqnr.h to the user headers list
sparse irqs: handle !GENIRQ platforms
sparseirq: fix !SMP && !PCI_MSI && !HT_IRQ build
sparseirq: fix Alpha build failure
sparseirq: fix typo in !CONFIG_IO_APIC case
x86, MSI: pass irq_cfg and irq_desc
x86: MSI start irq numbering from nr_irqs_gsi
x86: use NR_IRQS_LEGACY
sparse irq_desc[] array: core kernel and x86 changes
genirq: record IRQ_LEVEL in irq_desc[]
irq.h: remove padding from irq_desc on 64bits
