transport_lookup_tmr_lun() can be called from interrupt context and
therefore needs to use IRQ-safe spinlock functions. Fix this up, and
to make the locking work, convert the other uses of se_tmr_lock to be
IRQ-disabling.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
se_dev_check_online() is called from transport_lookup_cmd_lun(), which
as discussed before may be called from interrupt context. So it needs
to use spin_lock_irqsave() instead of spin_lock_irq() to avoid
enabling interrupts at the wrong time.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
transport_lookup_cmd_lun() may be called from interrupt context (eg
tcm_loop_allocate_core_cmd() calls it, and it has a comment that says,
"Can be called from interrupt context"), so it needs to use
spin_lock_irqsave() instead of spin_lock_irq() to avoid enabling
interrupts at the wrong time.
(And indeed the last set of lock operations, on lun_cmd_lock, were
already using spin_lock_irqsave(), so we just need to fix the other
two locks we take)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds SCF_EMULATE_QUEUE_FULL support using -EAGAIN failures
via transport_handle_queue_full() to signal queue full in completion
path TFO->queue_data_in() and TFO->queue_status() callbacks.
This is done using a new se_cmd->transport_qf_callback() to handle
the following queue full exception cases within target core:
*) TRANSPORT_COMPLETE_OK (for completion path queue full)
*) TRANSPORT_COMPLETE_QF_WP (for TRANSPORT_WRITE_PENDING queue full)
*) transport_send_check_condition_and_sense() failure paths in
transport_generic_request_failure() and transport_generic_complete_ok()
All logic is driven using se_device->qf_work_queue -> target_qf_do_work()
to to requeue outstanding se_cmd at the head of se_dev->queue_obj->qobj_list
for transport_processing_thread() execution.
Tested using tcm_qla2xxx with MAX_OUTSTANDING_COMMANDS=128 for FCP READ
to trigger the TRANSPORT_COMPLETE_OK queue full cases, and a simulated
TFO->write_pending() -EAGAIN failure to trigger TRANSPORT_COMPLETE_QF_WP.
Reported-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a transport_handle_cdb_direct() optimization for mapping
and queueing tasks directly from within fabric processing context by calling
the newly exported transport_generic_new_cmd(). This currently expects to
be called from process context only, and will fail if called within interrupt
context.
This patch also leaves transport_generic_handle_cdb() unmodified for the
moment to function as expected with existing tcm_fc and ib_srpt fabrics,
and will be removed once these have been converted and tested with v4.1
code using transport_handle_cdb_direct().
Based on Andy's original patch here:
[PATCH 39/42] target: Call transport_new_cmd instead of adding to cmd queue
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The release_cmd_to_pool and release_cmd_direct methods are always the same.
Merge them into a single release_cmd method, and clean up the fallout.
(nab: fix breakage in transport_generic_free_cmd() parameter build breakage
in drivers/target/tcm_fc/tfc_cmd.c)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch contains a squashed version to remove unused SCF_* flags:
target: remove the unused SCF_SE_DISABLE_ONLINE_CHECK flag
target: remove the unused SCF_CMD_PASSTHROUGH_NOALLOC flag
target: remove the unused SCF_EMULATE_SYNC_UNMAP flag
target: remove the unused SCF_EMULATE_SYNC_CACHE flag
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch contains a squashed version of third round series cleanups,
improvements ,and simplfications from Andy and Christoph ahead of the
heavy lifting between round 3 -> 4 for the target core SGL conversion.
This include cleanups to the main target I/O path and other miscellaneous
updates.
target: Replace custom sg<->buf functions with lib funcs
target: Simplify sector limiting code
target: get_cdb should never return NULL
target: Simplify transport_memcpy_se_mem_read_contig
target: Use assignment rather than increment for t_task_cdbs
target: Don't pass dma_size to generic_get_mem
target: Pass sg with type scatterlist in transport_map_sg_to_mem
target: Move task_sg_num next to task_sg in struct se_task
target: inline struct se_transport_task into struct se_cmd
target: Change name & semantics of transport_get_sectors()
target: Remove unused members of se_cmd
target: Rename se_cmd.t_task_cdbs to t_task_list_num
target: Fix some spelling
target: Remove unused var from transport_generic_do_tmr
target: map_sg_to_mem: return sg_count in return value
target/pscsi: Use min_t for sector limits
target/pscsi: Unused param for pscsi_get_bio()
target: Rename get_cdb_count to allocate_tasks
target: Make transport_generic_new_cmd() available for iscsi-target
target: Remove fabric callback to allocate iovecs
target: Fix transport_generic_new_cmd WRITE comment
(hch: Use __GFP_ZERO usage for alloc_pages() usage)
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes the handling of WRITE_SAME_[16,32] emulation where a
WRITE_SAME_* CDB with number of blocks=0 was being rejected by SCSI
expected data transfer length overflow checking in target core.
It changes both CDB cases in transport_generic_cmd_sequencer() to use
dev->se_sub_dev->se_dev_attrib.block_size to match what sg_write_same
is sending us with --num=0. It also fixes target_emulate_write_same()
to properly determine the num_blocks with --num=0 case to determine the
remaining range for dev->transport->do_discard().
Reported-by: Chris Greiveldinger <chris.greiveldinger@rnanetworks.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in the assignment of cmd->t_task.t_task_lba with
WRITE_SAME_16 to correctly use get_unaligned_be64() for the 64-bit LBA.
Reported-by: Chris Greiveldinger <chris.greiveldinger@rnanetworks.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
This patch contains the squashed version of second round of target core
cleanups and simplifications and Andy and Co. It also contains a handful
of fixes to address bugs the original series and other minor cleanups.
Here is the condensed shortlog:
target: Remove unneeded casts to void*
target: Rename get_lun_for_{cmd,tmr} to lookup_{cmd,tmr}_lun
target: Make t_task a member of se_cmd, not a pointer
target: Handle functions returning "-2"
target: Use cmd->se_dev over cmd->se_lun->lun_se_dev
target: Embed qr in struct se_cmd
target: Replace embedded struct se_queue_req with a list_head
target: Rename list_heads that are nodes in struct se_cmd to "*_node"
target: Fold transport_device_setup_cmd() into lookup_{tmr,cmd}_lun()
target: Make t_mem_list and t_mem_list_bidi members of t_task
target: Add comment & cleanup transport_map_sg_to_mem()
target: Remove unneeded checks in transport_free_pages()
(Roland: Fix se_queue_req removal leftovers OOPs)
(nab: Fix transport_lookup_tmr_lun failure case)
(nab: Fix list_empty(&cmd->t_task.t_mem_bidi_list) inversion bugs)
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The code in transport_add_device_to_core_hba() really intends to make sure
that neither inquiry_prod nor inquiry_rev is NULL.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
This patch contains the squashed version of a number of cleanups and
minor fixes from Andy's initial series (round 1) for target core this
past spring. The condensed log looks like:
target: use errno values instead of returning -1 for everything
target: Rename transport_calc_sg_num to transport_init_task_sg
target: Fix leak in error path in transport_init_task_sg
target/pscsi: Remove pscsi_get_sh() usage
target: Make two runtime checks into WARN_ONs
target: Remove hba queue depth and convert to spin_lock_irq usage
target: dev->dev_status_queue_obj is unused
target: Make struct se_queue_req.cmd type struct se_cmd *
target: Remove __transport_get_qr_from_queue()
target: Rename se_dev->g_se_dev_list to se_dev_node
target: Remove struct se_global
target: Simplify scsi mib index table code
target: Make dev_queue_obj a member of se_device instead of a pointer
target: remove extraneous returns at end of void functions
target: Ensure transport_dump_vpd_ident_type returns null-terminated str
target: Function pointers don't need to use '&' to be assigned
target: Fix comment in __transport_execute_tasks()
target: Misc style cleanups
target: rename struct pr_reservation_template to pr_reservation
target: Remove #defines that just perform indirection
target: Inline transport_get_task_from_execute_queue()
target: Minor header comment fixes
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes two instances of left over v3.x code performing local
scope access to struct target_core_fabric_ops->tf_subsys->su_group in
target_fabric_configfs_register() and target_fabric_configfs_deregister().
Reported-by: Christophe Fergeau <cfergeau@gmail.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
This patch removes the now unnecessary 'unsigned char *cdb' function
parameter from transport_get_lun_for_cmd(). This also includes updating
lio-target, tcm_loop and tcm_fc usage of transport_get_lun_for_cmd().
Reported-by: Fubo Chen <fubo.chen@gmail.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
This patch checks the passed 'unpacked_lun' against TRANSPORT_MAX_LUNS_PER_TPG
before reading from struct se_node_acl->device_list[].
Signed-off-by: Fubo Chen <fubo.chen@gmail.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
This patch fixes the following conversion specification warning for size_t
drivers/target/tcm_fc/tfc_io.c: In function ‘ft_queue_data_in’:
drivers/target/tcm_fc/tfc_io.c:209: warning: format ‘%x’ expects type ‘unsigned int’, but argument 5 has type ‘size_t’
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There is a typo here, it should be an unlock instead of a lock. The
original code will deadlock.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in ft_send_tm() that was incorrectly calling
ft_get_lun_for_cmd() -> transport_get_lun_for_cmd(), instead of using
transport_get_lun_for_tmr() for the proper struct se_lun lookup
that was triggering an OOPs in the se_cmd->tmr_req failure path.
This patch fixes the issue by re-arranging the codepath where
transport_get_lun_for_tmr() is called after tmr request is allocated and
made it available as part of se_cmd.
It also drops the now unnecessary ft_get_lun_for_cmd() unpacking code, and
uses scsilun_to_int() directly ahead of transport_get_lun_for_cmd() and
transport_get_lun_for_tmr() usage.
Signed-off-by: Patil, Kiran <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
This patch fixes a number of cases in target core using an incorrectly
if (strlen(foo) > SOME_MAX_SIZE)
As strlen() returns the number of characters in the string not counting
the NULL character at the end. So if you do something like:
char buf[10];
if (strlen("0123456789") > 10)
return -ETOOLONG;
snprintf(buf, 10, "0123456789");
printf("%s\n", buf);
then the last "9" gets chopped off and only "012345678" is printed.
Plus I threw in one small related cleanup.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In the original code, there were several places inside the
target_fabric_configfs_init() function that returned NULL on error
and one place the returned an ERR_PTR. There are two places that
call this function and they only check for NULL returns; they don't
check for ERR_PTRs. So I've changed the ERR_PTR so now the function
only returns NULL on error.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
transport_init_session() and core_tmr_alloc_req() never return NULL,
they only return ERR_PTRs on error.
v2: Fix patch to return PTR_ERR(tl_nexus->se_sess) from Ankit Jain's
feedback.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Ankit Jain <jankit@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts transport_deregister_session_configfs() to save/restore
spinlock IRQ state for struct se_node_acl->nacl_sess_lock access as tcm_qla2xxx
logic expects to call transport_deregister_session_configfs() code with
irq save already held for struct qla_hw_data.
Reported-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts target core and follwing scsi-misc upstream fabric
modules to use include/scsi/scsi_tcq.h includes for SIMPLE, HEAD_OF_QUEUE
and ORDERED SCSI tasks instead of scsi/libsas.h with TASK_ATTR*
*) tcm_loop: Convert tcm_loop_allocate_core_cmd() + tcm_loop_device_reset() to
scsi_tcq.h
*) tcm_fc: Convert ft_send_cmd() from FCP_PTA_* to scsi_tcq.h
Reported-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This patch converts transport_core_report_lun_response() to use
drivers/scsi/scsi_scan.c:int_to_scsilun instead of using the
struct target_core_fabric_ops->pack_lun() fabric provided API vector.
It also removes the tfo->pack_lun check from target_fabric_tf_ops_check()
and removes from struct target_core_fabric_ops->pack_lun() from
target_core_fabric_ops.h, and the following mainline scsi-misc fabric
modules:
*) tcm_loop: Drop tcm_loop_pack_lun() usage
*) tcm_fc: Drop ft_pack_lun() usage
Reported-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This patch fixes a bug where task->task_execute_queue=1 was not being
cleared once se_task had been removed from se_device->execute_task_list,
resulting in an OOPs in core_tmr_lun_reset() for the task->task_active=0
case where transport_remove_task_from_execute_queue() was incorrectly
being called.
This patch fixes two cases in transport_get_task_from_execute_queue()
and transport_remove_task_from_execute_queue() to properly clear
task->task_execute_queue=0 once list_del(&task->t_execute_list) has
been called.
It also adds an explict check in transport_remove_task_from_execute_queue()
to dump_stack + return if called with task->task_execute_queue=0.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This patch addresses a bug in the target core release path for HW
operation where transport_free_dev_tasks() was incorrectly being called
from transport_lun_remove_cmd() while releasing a se_cmd reference and
calling struct target_core_fabric_ops->queue_data_in().
This would result in a OOPs with HW target mode when the release of
se_task->task_sg[] would happen before pci_unmap_sg() can be called in
HW target mode fabric module code. This patch addresses the issue by
moving transport_free_dev_tasks() from transport_lun_remove_cmd() into
transport_generic_free_cmd(), and adding TRANSPORT_FREE_CMD_INTR and
transport_generic_free_cmd_intr() to allow se_cmd descriptor release
to happen fromfrom within transport_processing_thread() process context
when release of se_cmd is not possible from HW interrupt context.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This patch fixes two bugs wrt to the interrupt context usage of target
core with HW target mode drivers. It first converts the usage of struct
se_device->stats_lock in transport_get_lun_for_cmd() and core_tmr_lun_reset()
to properly use spin_lock_irq() to address an BUG with CONFIG_LOCKDEP_SUPPORT=y
enabled.
This patch also adds a 'in_interrupt()' check to allow GFP_ATOMIC usage from
core_tmr_alloc_req() to fix a 'sleeping in interrupt context' BUG with HW
target fabrics that require this logic to function.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This patch fixes a bug in transport_do_task_sg_chain() used by HW target
mode modules with sg_chain() to provide a single sg_next() walkable memory
layout for use with pci_map_sg() and friends. This patch addresses an
issue with mapping multiple small block max_sector tasks across multiple
struct se_task->task_sg[] mappings for HW target mode operation.
This was causing OOPs with (cmd->t_task->t_tasks_no > 1) I/O traffic for
HW target drivers using transport_do_task_sg_chain(), and has been tested
so far with tcm_fc(openfcoe), tcm_qla2xxx, and ib_srpt fabrics with
t_tasks_no > 1 IBLOCK backends using a smaller max_sectors to trigger the
original issue.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Acked-by: Kiran Patil <kiran.patil@intel.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
This is a comprehensive patch for FC-FC4 provider. tcm_fc is a FC-FC4
provider which glues target core (TCM) with Fiber channel library
(libfc). tcm_fc uses existing FC4 provider hooks from Fiber channel
library. This Fiber channel library is used by FCoE (transport - FC
over Ethernet) protocol driver as well.
Combination of modules such as Fiber channel library, tcm_fc, TCM
target core, and FCoE protocol driver enables functional FCoE target.
This patch includes initial commit for tcm_fc plus additional
enhancement, bug fixes.
This tcm_fc module essentially contains 3 entry points such as "prli",
"prlo", "recv". When process login request (ELS_PRLI) request is
received, Fiber channel library (libfc) module calls passive providers
(FC-FC4, tcm_fc) (if any registered) "prli" function. Likewise when
LOGO request is received, "prlo" function of passive provider is
invoked by libfc. For all other request (e.g. any read/write, task
management, LUN inquiry commands), "recv" function of passiver
provider is invoked by libfc. Those passive providers "prli, prlo,
recv" functions interact with TCM target core for requested operation.
This module was primarily developed by "Joe Eykholt" and there were
significant contributions from the people listed under signed-off.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (55 commits)
[SCSI] tcm_loop: Add multi-fabric Linux/SCSI LLD fabric module
[SCSI] qla4xxx: Use polling mode for disable interrupt mailbox completion
[SCSI] Revert "[SCSI] Retrieve the Caching mode page"
[SCSI] bnx2fc: IO completion not processed due to missed wakeup
[SCSI] qla4xxx: Update driver version to 5.02.00-k6
[SCSI] qla4xxx: masking required bits of add_fw_options during initialization
[SCSI] qla4xxx: added new function qla4xxx_relogin_all_devices
[SCSI] qla4xxx: add support for ql4xsess_recovery_tmo cmd line param
[SCSI] qla4xxx: Add support for ql4xmaxqdepth command line parameter
[SCSI] qla4xxx: cleanup function qla4xxx_process_ddb_changed
[SCSI] qla4xxx: Prevent other port reinitialization during remove_adapter
[SCSI] qla4xxx: remove unused ddb flag DF_NO_RELOGIN
[SCSI] qla4xxx: cleanup DDB relogin logic during initialization
[SCSI] qla4xxx: Do not retry ISP82XX initialization if H/W state is failed
[SCSI] qla4xxx: Do not send mbox command if FW is in failed state
[SCSI] qla4xxx: cleanup qla4xxx_initialize_ddb_list()
[SCSI] ses: add subenclosure support
[SCSI] bnx2fc: Bump version to 1.0.1
[SCSI] bnx2fc: Remove unnecessary module state checks
[SCSI] bnx2fc: Fix MTU issue by using static MTU
...
* 'for-2.6.39/core' of git://git.kernel.dk/linux-2.6-block: (65 commits)
Documentation/iostats.txt: bit-size reference etc.
cfq-iosched: removing unnecessary think time checking
cfq-iosched: Don't clear queue stats when preempt.
blk-throttle: Reset group slice when limits are changed
blk-cgroup: Only give unaccounted_time under debug
cfq-iosched: Don't set active queue in preempt
block: fix non-atomic access to genhd inflight structures
block: attempt to merge with existing requests on plug flush
block: NULL dereference on error path in __blkdev_get()
cfq-iosched: Don't update group weights when on service tree
fs: assign sb->s_bdi to default_backing_dev_info if the bdi is going away
block: Require subsystems to explicitly allocate bio_set integrity mempool
jbd2: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
jbd: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
fs: make fsync_buffers_list() plug
mm: make generic_writepages() use plugging
blk-cgroup: Add unaccounted time to timeslice_used.
block: fixup plugging stubs for !CONFIG_BLOCK
block: remove obsolete comments for blkdev_issue_zeroout.
blktrace: Use rq->cmd_flags directly in blk_add_trace_rq.
...
Fix up conflicts in fs/{aio.c,super.c}
This patch adds the TCM_Loop Linux/SCSI LLD fabric module for
accessing TCM device backstores as locally accessable SCSI LUNs in
virtual SAS, FC, and iSCSI Target ports using the generic fabric
TransportID and Target Port WWN naming handlers from TCM's
target_core_fabric_lib.c The TCM_Loop module uses the generic fabric
configfs infratructure provided by target_core_fabric_configfs.c and
adds a module dependent attribute for the creation/release of the
virtual I_T Nexus connected the TCM_Loop Target and Initiator Ports.
TCM_Loop can also be used with scsi-generic and BSG drivers so that
STGT userspace fabric modules, QEMU-KVM and other hypervisor SCSI
passthrough support can access TCM device backstore and control CDB
emulation.
For more information please see:
http://linux-iscsi.org/wiki/Tcm_loop
[jejb: fixed up checkpatch stuff]
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch adds a target_core_mib.c statistics conversion for
backend context struct se_subsystem_dev + struct se_device config_group
based statistics in target_core_device.c using CONFIGFS_EATTR()
based struct config_item_types from target_core_stat.c code.
The conversion from backend /proc/scsi_target/mib/ context output to configfs
default groups+attributes include scsi_dev, scsi_lu, and scsi_tgt_dev output
from within individual:
/sys/kernel/config/target/core/$HBA/DEV/
The legacy procfs output now appear as individual configfs attributes under:
*) $HBA/$DEV/statistics/scsi_dev:
|-- indx
|-- inst
|-- ports
`-- role
*) $HBA/$DEV/statistics/scsi_lu:
|-- creation_time
|-- dev
|-- dev_type
|-- full_stat
|-- hs_num_cmds
|-- indx
|-- inst
|-- lu_name
|-- lun
|-- num_cmds
|-- prod
|-- read_mbytes
|-- resets
|-- rev
|-- state_bit
|-- status
|-- vend
`-- write_mbytes
*) $HBA/$DEV/statistics/scsi_tgt_dev:
|-- indx
|-- inst
|-- non_access_lus
|-- num_lus
|-- resets
`-- status
The conversion from backend /proc/scsi_target/mib/ context output to configfs
default groups+attributes include scsi_port, scsi_tgt_port and scsi_transport
output from within individual:
/sys/kernel/config/target/fabric/$WWN/tpgt_$TPGT/lun/lun_$LUN_ID/statistics/
The legacy procfs output now appear as individual configfs attributes under:
*) fabric/$WWN/tpgt_$TPGT/lun/lun_$LUN_ID/statistics/scsi_port
|-- busy_count
|-- dev
|-- indx
|-- inst
`-- role
*) fabric/$WWN/tpgt_$TPGT/lun/lun_$LUN_ID/statistics/scsi_tgt_port
|-- dev
|-- hs_in_cmds
|-- in_cmds
|-- indx
|-- inst
|-- name
|-- port_index
|-- read_mbytes
`-- write_mbytes
*) fabric/$WWN/tpgt_$TPGT/lun/lun_$LUN_ID/statistics/scsi_transport
|-- dev_name
|-- device
|-- indx
`-- inst
The conversion from backend /proc/scsi_target/mib/ context output to configfs
default groups+attributes include scsi_att_intr_port and scsi_auth_intr output
from within individual:
/sys/kernel/config/target/fabric/$WWN/tpgt_$TPGT/acls/$INITIATOR_WWN/lun_$LUN_ID/statistics/
The legacy procfs output now appear as individual configfs attributes under:
*) acls/$INITIATOR_WWN/lun_$LUN_ID/statistics/scsi_att_intr_port
|-- dev
|-- indx
|-- inst
|-- port
|-- port_auth_indx
`-- port_ident
*) acls/$INITIATOR_WWN/lun_$LUN_ID/statistics/scsi_auth_intr
|-- att_count
|-- creation_time
|-- dev
|-- dev_or_port
|-- hs_num_cmds
|-- indx
|-- inst
|-- intr_name
|-- map_indx
|-- num_cmds
|-- port
|-- read_mbytes
|-- row_status
`-- write_mbytes
Also, this includes adding struct target_fabric_configfs_template->
tfc_wwn_fabric_stats_cit and ->tfc_tpg_nacl_stat_cit respectively for
use during target_core_fabric_configfs.c:target_fabric_setup_cits()
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fixes the follownig section mismatch warning:
WARNING: vmlinux.o(.text+0x21617a): Section mismatch in reference from the
function target_core_init_configfs() to the function .init.text:rd_module_init()
The function target_core_init_configfs() references the function __init
rd_module_init(). This is often because target_core_init_configfs() lacks
a __init annotation or the annotation of rd_module_init is wrong.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fixes a token typo for the TCM/FILEIO match_table_t used
for toggling O_SYNC usage for individual struct file backend access.
Reported-by: Christophe Fergeau <cfergeau@gmail.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch removes a bogus conditional+return check within the failure path
of transport_add_device_to_core_hba(). This breakage was introduced during
the v4 conversion to remove struct se_cmd passthrough ops for INQUIRY /
READ_CAPCITY during struct se_device creation and registration process.
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In drivers/target/target_core_transport.c::transport_generic_get_mem()
there are a few potential memory leaks in the error paths. This patch
makes sure that we free previously allocated memory when other allocations
fail. It also moves some work (INIT_LIST_HEAD() and assignment to
se_mem->se_len) below all the allocations so that if something fails we
don't do the work at all.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch changes include/target/target_core_tmr.h code to use
target specific 'TMR_*' prefixed definitions for fabric independent
SCSI Task Management Request/Request naming in include/scsi/scsi.h
definitions for mainline target code.
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch converts rd_build_device_space() to return errno usage
for failures in rd_create_virtdevice().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch addresses the majority of sparse warnings and adds
proper locking annotations. It also fixes the dubious one-bit signed
bitfield, for which the signed one-bit types can be 0 or -1 which can
cause a problem if someone ever checks if (foo->lu_gp_assoc == 1).
The current code is fine because everyone just checks zero vs non-zero.
But Sparse complains about it so lets change it. The warnings look like
this:
include/target/target_core_base.h:228:26: error: dubious one-bit signed bitfield
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Fubo Chen <fubo.chen@gmail.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch removes a legacy struct se_hba->hba_dev_list -> se_release_device_for_hba()
list walk in core_delete_hba(), which is no longer required while using configfs
VFS level parent/child struct config_group dependency referencing. The reason
is because any struct se_hba->hba_dev_list-> struct se_device members are going
to have to be released via:
rmdir /sys/kernel/config/target/core/$HBA/*
before rmdir release of struct se_hba via target_core_configfs.c:
target_core_call_delhbafromtarget() -> core_delete_hba()
rmdir /sys/kernel/config/target/core/$HBA
to release struct se_hba in core_delete_hba().
This patch also removes the legacy se_clear_dev_ports() function, which is
left-over pre-configfs shutdown logic for when se_free_virtual_device()
was responsible for walking struct se_device->dev_sep_list and calling
core_dev_del_lun() for each individual active struct se_port->se_lun.
The reason this can be removed is because all struct se_device->dev_sep_list
-> struct se_port communication is done via configfs symlinks, which
means that an target fabric module's endpoints containg active struct
se_port(s) will have to be released via target_core_fabric_configfs.c:
target_fabric_port_unlink() via:
unlink /sys/kernel/config/target/$FABRIC_MOD/$ENDPOINT/tpgt_$TPGT/lun/lun_$LUN_ID/<symlink>
before rmdir release of struct se_device in target_core_configfs.c:
target_core_drop_subdev() -> se_free_virtual_device() can happen via:
rmdir /sys/kernel/config/target/core/$HBA/*
to release struct se_subsystem_dev in target_core_drop_subdev()
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Reported-by: Fubo Chen <fubo.chen@gmail.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch converts the target_core_store_dev_enable() -> struct
se_subsystem_api->create_virtdevice() call to return proper ERR_PTR values
back up to configfs logic during backend dependent struct se_device ENABLE
exception conditions.
Along with the change to target_core_configfs.c, this includes converting IBLOCK,
FILEIO, pSCSI, and RAMDISK_* backend subsystem plugins to obtain upper level
PTR_ERR return codes (where available), and return via ERR_PTR during a
*_create_virtdev() failure.
Reported-by: Fubo Chen <fubo.chen@gmail.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
