Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add new WQE fields as defined by new SLI interface to support new hardware.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix critical errors
- Update send_scsi_event to validate pnode pointer active before copying
the wwpn information.
- Add a message, mailbox_idle, and unlock before failing SECURITY_MGMT
or AUTH_PORT mailbox commands
- Prevent spin_lock_irqsave from being called twice in a row.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adapter Shutdown and Unregistration cleanup
- Correct the logic around hba shutdown. Prior to final reset, the
driver must wait for all XRIs to return from the adapter. Added logic
to poll, progressively slowing the poll rate as delay gets longer.
- Correct behavior around the rsvd1 field in UNREG_RPI_ALL mailbox
completion and final rpi cleanup.
- Updated logic to move pending VPI registrations to their completion
in cases where a CVL may be received while registration in progress.
- Added unreg all rpi mailbox command before unreg vpi.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added driver logic to detect the last devloss timeout of remote nodes which
was still in use of FCF. At that point, the driver should set the last
in-use remote node devloss timeout flag if it was not already set and should
perform proper action on the in-use FCF and recover of FCF from firmware,
depending on the state the driver's FIP engine is in.
Find eligible FCF through FCF table rescan or the next new FCF event when
FCF table rescan turned out empty eligible FCF, and the successful flogi
into an FCF shall clear the HBA_DEVLOSS_TMO flag, indicating the successful
recovery from devloss timeout.
[jejb: add delay.h include to lpfc_hbadisc.c to fix ppc compile]
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add support of received ELS commands
- Add support for received RLS ELS command
- Add support for received ECHO ELS command
- Add support for received RTV ELS command
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FC/FCoE Discovery fixes:
- Call the lpfc_drain_txq only for SLI4 hba
- In lpfc_cmpl_els_fdisc, fix code path that does not free IOCB.
- Treated firmware matching FCF property with different index as error
- Propagate error returns from lpfc_issue_els_flogi()
- Refactored lpfc_unregister_unused_fcf() to create a post
lpfc_dev_loss_tmo handler call for SLI-4 devices. Allows checking of
fcf after last ndlp released so that fcf can be released if no longer
in use.
- Replaced individual FCF_XXXX_DISC flag clearing in lieu of aggregate
FCF_DISCOVERY flag upon succesful completion of flogi.
- Correct setting of altBbCredit value in sparams to correct issue with
logins with remote loop-based devices.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Update lpfc driver version to 8.3.17
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Replace graceful teardown steps with the singular function reset command.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Fail I/Os with incomplete data that complete with SCSI Check condition.
- Complete aborted I/Os with host_scribble equal to NULL with success.
- Initialize context1 field of iocbq in the new_scsi_buf routines.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add support for bsg MBX_SLI4_CONFIG.
- Multiply linkup timeout in loopback test code by 100.
- Set iocb_stat to 0 in the lpfcdiag_loop_get_xri function.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Added driver support for management application to pass down two security
specific mailbox commands (MBX_SECURITY_MGMT and MBX_AUTH_PORT)
- Added driver support for handling FIPS zeroization trap of host ERATT ER8,
performing selective reset and bringing the device up.
- Added code to detect INIT_LINK mailbox command completion returning status
MBXERR_SEC_NO_PERMISSION.
- Increased the wait timeout on host status register HS_FFRDY and HS_MBRDY
being set.
- Remove the port offline code from the Heartbeat TMO handler.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Move Unload flag earlier in vport deletei to stop ELS traffic
- Replaced some unnecessary spin_lock_irqsave with spin_lock_irq
- Fixed circular spinlock dependency between low-level driver and SCSI midlayer
- Remove duplicate code from lpfc_els_retry routine
- Make all error values negative
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This removes the driver's get_host_def_dev_loss_tmo
callback and just has the driver set the dev loss
using the fc class fc_host_dev_loss_tmo macro like is
done for other fc params.
It also adds compat support for the driver's existing
dev loss and nodev sysfs and modparams.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In lpfc_cleanup_pending_mbox() we already have IRQs disabled so we don't
need to disable them again.
Also in lpfc_sli_intr_handler() there is a typo where it has
spin_unlock_irq() instead of just spin_unlock().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This fixes a bug where the driver was resetting the
rport dev_loss_tmo when devices were added by adding
support for the get_host_def_dev_loss_tmo callout.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (28 commits)
[SCSI] qla4xxx: fix compilation warning
[SCSI] make error handling more robust in the face of reservations
[SCSI] tgt: fix warning
[SCSI] drivers/message/fusion: Adjust confusing if indentation
[SCSI] Return NEEDS_RETRY for eh commands with status BUSY
[SCSI] ibmvfc: Driver version 1.0.9
[SCSI] ibmvfc: Fix terminate_rport_io
[SCSI] ibmvfc: Fix rport add/delete race resulting in oops
[SCSI] lpfc 8.3.16: Change LPFC driver version to 8.3.16
[SCSI] lpfc 8.3.16: FCoE Discovery and Failover Fixes
[SCSI] lpfc 8.3.16: SLI Additions, updates, and code cleanup
[SCSI] pm8001: introduce missing kfree
[SCSI] qla4xxx: Update driver version to 5.02.00-k3
[SCSI] qla4xxx: Added AER support for ISP82xx
[SCSI] qla4xxx: Handle outstanding mbx cmds on hung f/w scenarios
[SCSI] qla4xxx: updated mbx_sys_info struct to sync with FW 4.6.x
[SCSI] qla4xxx: clear AF_DPC_SCHEDULED flage when exit from do_dpc
[SCSI] qla4xxx: Stop firmware before doing init firmware.
[SCSI] qla4xxx: Use the correct request queue.
[SCSI] qla4xxx: set correct value in sess->recovery_tmo
...
To avoid more patches, I also fixed other spelling
and grammar bugs when they were in the same or
following line:
successfull -> successful
parse -> parses
controler -> controller
controlers -> controllers
Cc: Jiri Kosina <trivial@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add support for re-reg'ing changed VPI w/o unregister VPI
- Copy WWN and state from old nodelist when target DID change.
- Clean up old nodelist rport and put the nodelist when target DID change.
- Clear the VFI_REGISTERED flag when UNREG_VFI completes.
- Made both checks of port_state against LPFC_FLOGI and LPFC_FDISC
non-inclusive for ignoring CVL events.
- Added logic to stop retrying of the ongoing PLOGI and FDISC if
transitioned back to the FCF rediscovery state in reaction to CVL.
- Removed the dependency of scanning of all the available FCF table
entries for bulding round-robin bitmap.
- Use the lpfc_sli4_fcf_rr_read_fcf_rec() in responding to
individual New FCF found event.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Remove unneeded Endian swap for Block Guard IOCB response
- Add a check for mailbox active before issuing the heartbeat command
- Correct heartbeat last_completion updates to avoid unneeded heartbeats
- Add Security crypto support to CONFIG_PORT mailbox command
- Add fips level and fips spec revision sysfs parameters
- Remove duplicate setting of ext_byte_len fields in lpfc_bsg_issue_mbox
- Switch call to memcpy_toio to __write32_copy to prevent unaligned 64 bit copy
- Change log message 0318 from an error to a warning as it is not an error
- Patch an incorrect call to lpfc_drain_txq on SLI-3 functions
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FCoE Related Fixes
- Correct find-next-FCF routine so that it searches at next FCF rather
than current one.
- Enhanced round-robin FCF failover algorithm to re-start on "New FCF"
async event
- Update the manner in which we look at FCFs while they may be in
their discovery state.
- Use LPFC_FCOE_NULL_VID macro when checkinf for valid vlan_id for FCF
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- BSG interface related:
- Fix node reference count if node is active
- Warn if we're overwriting an active CT context
- Discovery related:
- Clear "Ignore Reg Login" flag when purging mailbox queue
- Pay attention to return code for fc_block_scsi_eh()
- Stall device loss code if we're almost done when it fires
(we're logged in, but PRLI is outstanding)
- Bugs
- Correct DIF code for endianness issues
- Correct where we had missed points to check txq on i/o
completion/cleanup
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Fixed accounting of allocated SCSI buffers when post sgl fails.
- Restrict scsi buffer allocation based on LUN count (sdev_cnt).
- Create __lpfc_sli_free_rpi that doesn't take out the hbalock.
- Modify lpfc_sli_free_rpi to call __lpfc_sli_free_rpi.
- Call __lpfc_sli_free_rpi in lpfc_cleanup_pending_mbox.
- Do not swap the strings returned in mailbox commands and do
not swap byte aligned data in VPD.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Prevent unregistring of unused FCF when FLOGI is pending.
- Prevent point to point discovery on a FCoE HBA.
- Fixed FCF discovery failure after swapping FCoE port by
switching over to fast failover method when no FCF matches in-use FCF.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Allow enabling MSI-X intterupts with fewer vectors than requested
by looking at the return value from pci_enable_msix.
- Implemented driver PCI AER error handling routines for supporting
AER error recovering on SLI4 devices.
- Remove redundant SLI_ACTIVE checks
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Change the Max receive size on CIN FCFs to 0x800
- (From linux community) Check boundary before checking for NULL.
- Update last completion time for completed I/O to prevent heartbeat.
- Add Balius PCI Device IDs
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Fix hba_queue_depth to reflect actual available XRIs
- Add support for new SLER specific firmware status codes.
- Free SCSI buffer when iotag allocation fails.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add poll or wait flag parameter to hba_init_link and hba_down_link.
- (From Linux Community) Make return with ENXIO negative.
- Remove unused INB code from driver.
- Prevent block_magmt_io from returning until mailbox is inactive.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Retry PLOGI up to 48 times when LS_RJT reason is
"Unable to supply requested data."
- When dev loss timeout occures do not change state if there
is an outstanding REG_LOGIN.
- Add logic to ignore REG_LOGIN completion if discovery is
restarted while waiting for REG_LOGIN.
- Only change state on REG_LOGIN completion if still in
state waiting for REG_LOGIN completion.
- Only send ADISCs to FCP-2 Targets (not Initiators).
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add code to prevent unreg_vpi mailbox command from failing.
- Add code to reset the HBA if unreg_vpi mailbox fails with busy status.
- Remove code that was clearing the nlp_type stored during rport discovery.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add memcpy to mailbox completion to transfer reply correctly.
- Add support for BSG mailbox commands (dump, update_cfg, and
event_log_status).
- Add warning message and refuse mailbox command while mgmt is blocked.
- Add checks for memory allocation failure.
- Add check for sli4 dump zero BDE size.
- Only copy data if mailbox commands succeed.
- Add support for Read Event Log mailbox command.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Move the code to increase the sg seg count for LP21000 adapters.
- Check pcmd on command completion before dereferencing it.
- Clear queue memory when creating firmware queues to prevent stale entries.
- Replace the use of PAGE_SIZE in many areas that assumed it was always 4k.
- Add an else clause to a conditional that needed to unlock the hba_lock.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Update driver for change in T10-PI interface on adapter
- Remove Profiles.
- Add new SLI Opcodes.
- Add new PDE structures used for BlockGuard.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Prevent log message 1801 during vport delete.
- Enable NPIV by default.
- Display correct value for max Vports on SLI4 HBAs.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add the new Logical Link speed event support.
- Add RATOV and EDTOV to the REG_VFI mailbox command.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Enable NPIV by default.
- Added code to handle unsolicited LOGO on physical port.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Only abort outstanding I/O to force the OS to retry failed I/Os for AER
uncorrectable non-fatal errors instead of reseting the adapter.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
