Some HWs need the VF driver to put part of the packet headers on the
TX descriptor so the e-switch can do proper matching and steering.
The supported modes: none, link, network, transport.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers would need to check few internal matters for
that. To be used in downstream mlx5 commit.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the link is filtered out, loop index should also be updated. If not,
loop index will not be correct.
Fixes: dc599f76c2 ("net: Add support for filtering link dump by master device and kind")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
size_t is way too much for an integer not exceeding 64.
Space savings: 10 bytes!
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-10 (-10)
function old new delta
napi_consume_skb 165 163 -2
__kfree_skb_flush 56 53 -3
__kfree_skb_defer 97 92 -5
Total: Before=154865639, After=154865629, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing NDA_VLAN attribute's size.
Fixes: 1e53d5bb88 ("net: Pass VLAN ID to rtnl_fdb_notify.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding validation support for the ETHTOOL_PHY_DOWNSHIFT. Functional
implementation needs to be done in the individual PHY drivers.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding get_tunable/set_tunable function pointer to the phy_driver
structure, and uses these function pointers to implement the
ETHTOOL_PHY_GTUNABLE/ETHTOOL_PHY_STUNABLE ioctls.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make struct pernet_operations::id unsigned.
There are 2 reasons to do so:
1)
This field is really an index into an zero based array and
thus is unsigned entity. Using negative value is out-of-bound
access by definition.
2)
On x86_64 unsigned 32-bit data which are mixed with pointers
via array indexing or offsets added or subtracted to pointers
are preffered to signed 32-bit data.
"int" being used as an array index needs to be sign-extended
to 64-bit before being used.
void f(long *p, int i)
{
g(p[i]);
}
roughly translates to
movsx rsi, esi
mov rdi, [rsi+...]
call g
MOVSX is 3 byte instruction which isn't necessary if the variable is
unsigned because x86_64 is zero extending by default.
Now, there is net_generic() function which, you guessed it right, uses
"int" as an array index:
static inline void *net_generic(const struct net *net, int id)
{
...
ptr = ng->ptr[id - 1];
...
}
And this function is used a lot, so those sign extensions add up.
Patch snipes ~1730 bytes on allyesconfig kernel (without all junk
messing with code generation):
add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730)
Unfortunately some functions actually grow bigger.
This is a semmingly random artefact of code generation with register
allocator being used differently. gcc decides that some variable
needs to live in new r8+ registers and every access now requires REX
prefix. Or it is shifted into r12, so [r12+0] addressing mode has to be
used which is longer than [r8]
However, overall balance is in negative direction:
add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730)
function old new delta
nfsd4_lock 3886 3959 +73
tipc_link_build_proto_msg 1096 1140 +44
mac80211_hwsim_new_radio 2776 2808 +32
tipc_mon_rcv 1032 1058 +26
svcauth_gss_legacy_init 1413 1429 +16
tipc_bcbase_select_primary 379 392 +13
nfsd4_exchange_id 1247 1260 +13
nfsd4_setclientid_confirm 782 793 +11
...
put_client_renew_locked 494 480 -14
ip_set_sockfn_get 730 716 -14
geneve_sock_add 829 813 -16
nfsd4_sequence_done 721 703 -18
nlmclnt_lookup_host 708 686 -22
nfsd4_lockt 1085 1063 -22
nfs_get_client 1077 1050 -27
tcf_bpf_init 1106 1076 -30
nfsd4_encode_fattr 5997 5930 -67
Total: Before=154856051, After=154854321, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrei reports we still allocate netns ID from idr after we destroy
it in cleanup_net().
cleanup_net():
...
idr_destroy(&net->netns_ids);
...
list_for_each_entry_reverse(ops, &pernet_list, list)
ops_exit_list(ops, &net_exit_list);
-> rollback_registered_many()
-> rtmsg_ifinfo_build_skb()
-> rtnl_fill_ifinfo()
-> peernet2id_alloc()
After that point we should not even access net->netns_ids, we
should check the death of the current netns as early as we can in
peernet2id_alloc().
For net-next we can consider to avoid sending rtmsg totally,
it is a good optimization for netns teardown path.
Fixes: 0c7aecd4bd ("netns: add rtnl cmd to add and get peer netns ids")
Reported-by: Andrei Vagin <avagin@gmail.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of netpoll_poll_lock() own NAPI_STATE_SCHED
Callers of netpoll_poll_unlock() have BH blocked between
the NAPI_STATE_SCHED being cleared and poll_lock is released.
We can avoid the spinlock which has no contention, and use cmpxchg()
on poll_owner which we need to set anyway.
This removes a possible lockdep violation after the cited commit,
since sk_busy_loop() re-enables BH before calling busy_poll_stop()
Fixes: 217f697436 ("net: busy-poll: allow preemption in sk_busy_loop()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAPI drivers use napi_complete_done() or napi_complete() when
they drained RX ring and right before re-enabling device interrupts.
In busy polling, we can avoid interrupts being delivered since
we are polling RX ring in a controlled loop.
Drivers can chose to use napi_complete_done() return value
to reduce interrupts overhead while busy polling is active.
This is optional, legacy drivers should work fine even
if not updated.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 4cd13c21b2 ("softirq: Let ksoftirqd do its job"),
sk_busy_loop() needs a bit of care :
softirqs might be delayed since we do not allow preemption yet.
This patch adds preemptiom points in sk_busy_loop(),
and makes sure no unnecessary cache line dirtying
or atomic operations are done while looping.
A new flag is added into napi->state : NAPI_STATE_IN_BUSY_POLL
This prevents napi_complete_done() from clearing NAPIF_STATE_SCHED,
so that sk_busy_loop() does not have to grab it again.
Similarly, netpoll_poll_lock() is done one time.
This gives about 10 to 20 % improvement in various busy polling
tests, especially when many threads are busy polling in
configurations with large number of NIC queues.
This should allow experimenting with bigger delays without
hurting overall latencies.
Tested:
On a 40Gb mlx4 NIC, 32 RX/TX queues.
echo 70 >/proc/sys/net/core/busy_read
for i in `seq 1 40`; do echo -n $i: ; ./super_netperf $i -H lpaa24 -t UDP_RR -- -N -n; done
Before: After:
1: 90072 92819
2: 157289 184007
3: 235772 213504
4: 344074 357513
5: 394755 458267
6: 461151 487819
7: 549116 625963
8: 544423 716219
9: 720460 738446
10: 794686 837612
11: 915998 923960
12: 937507 925107
13: 1019677 971506
14: 1046831 1113650
15: 1114154 1148902
16: 1105221 1179263
17: 1266552 1299585
18: 1258454 1383817
19: 1341453 1312194
20: 1363557 1488487
21: 1387979 1501004
22: 1417552 1601683
23: 1550049 1642002
24: 1568876 1601915
25: 1560239 1683607
26: 1640207 1745211
27: 1706540 1723574
28: 1638518 1722036
29: 1734309 1757447
30: 1782007 1855436
31: 1724806 1888539
32: 1717716 1944297
33: 1778716 1869118
34: 1805738 1983466
35: 1815694 2020758
36: 1893059 2035632
37: 1843406 2034653
38: 1888830 2086580
39: 1972827 2143567
40: 1877729 2181851
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_xdp_size() only considers the size of the actual payload attribute,
and misses the space taken by the attribute used for nesting (IFLA_XDP).
Fixes: d1fdd91386 ("rtnl: add option for setting link xdp prog")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size reported by rtnl_vfinfo_size doesn't match the space used by
rtnl_fill_vfinfo.
rtnl_vfinfo_size currently doesn't account for the nest attributes
used by statistics (added in commit 3b766cd832), nor for struct
ifla_vf_tx_rate (since commit ed616689a3, which added ifla_vf_rate
to the dump without removing ifla_vf_tx_rate, but replaced
ifla_vf_tx_rate with ifla_vf_rate in the size computation).
Fixes: 3b766cd832 ("net/core: Add reading VF statistics through the PF netdevice")
Fixes: ed616689a3 ("net-next:v4: Add support to configure SR-IOV VF minimum and maximum Tx rate through ip tool")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit 14135f30e3 ("inet: fix sleeping inside inet_wait_for_connect()"),
sk_wait_event() needs to fix too, because release_sock() is blocking,
it changes the process state back to running after sleep, which breaks
the previous prepare_to_wait().
Switch to the new wait API.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After Tom patch, thoff field could point past the end of the buffer,
this could fool some callers.
If an skb was provided, skb->len should be the upper limit.
If not, hlen is supposed to be the upper limit.
Fixes: a6e544b0a8 ("flow_dissector: Jump to exit code in __skb_flow_dissect")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Yibin Yang <yibyang@cisco.com
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the bpf program calls bpf_redirect(dev, 0) and dev is
an ipip/ip6tnl, it currently includes the mac header.
e.g. If dev is ipip, the end result is IP-EthHdr-IP instead
of IP-IP.
The fix is to pull the mac header. At ingress, skb_postpull_rcsum()
is not needed because the ethhdr should have been pulled once already
and then got pushed back just before calling the bpf_prog.
At egress, this patch calls skb_postpull_rcsum().
If bpf_redirect(dev, BPF_F_INGRESS) is called,
it also fails now because it calls dev_forward_skb() which
eventually calls eth_type_trans(skb, dev). The eth_type_trans()
will set skb->type = PACKET_OTHERHOST because the mac address
does not match the redirecting dev->dev_addr. The PACKET_OTHERHOST
will eventually cause the ip_rcv() errors out. To fix this,
____dev_forward_skb() is added.
Joint work with Daniel Borkmann.
Fixes: cfc7381b30 ("ip_tunnel: add collect_md mode to IPIP tunnel")
Fixes: 8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no more users except from net/core/dev.c
napi_hash_add() can now be static.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates a new type of interfaceless lightweight tunnel (SEG6),
enabling the encapsulation and injection of SRH within locally emitted
packets and forwarded packets.
>From a configuration viewpoint, a seg6 tunnel would be configured as follows:
ip -6 ro ad fc00::1/128 encap seg6 mode encap segs fc42::1,fc42::2,fc42::3 dev eth0
Any packet whose destination address is fc00::1 would thus be encapsulated
within an outer IPv6 header containing the SRH with three segments, and would
actually be routed to the first segment of the list. If `mode inline' was
specified instead of `mode encap', then the SRH would be directly inserted
after the IPv6 header without outer encapsulation.
The inline mode is only available if CONFIG_IPV6_SEG6_INLINE is enabled. This
feature was made configurable because direct header insertion may break
several mechanisms such as PMTUD or IPSec AH.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid having dangling function pointers left behind, reset calcit in
rtnl_unregister(), too.
This is no issue so far, as only the rtnl core registers a netlink
handler with a calcit hook which won't be unregistered, but may become
one if new code makes use of the calcit hook.
Fixes: c7ac8679be ("rtnetlink: Compute and store minimum ifinfo...")
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receiving a GSO packet in dev_gro_receive() is not uncommon
in stacked devices, or devices partially implementing LRO/GRO
like bnx2x. GRO is implementing the aggregation the device
was not able to do itself.
Current code causes reorders, like in following case :
For a given flow where sender sent 3 packets P1,P2,P3,P4
Receiver might receive P1 as a single packet, stored in GRO engine.
Then P2-P4 are received as a single GSO packet, immediately given to
upper stack, while P1 is held in GRO engine.
This patch will make sure P1 is given to upper stack, then P2-P4
immediately after.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this check, it is not possible to create two rules that
are identical except for their UID ranges. For example:
root@net-test:/# ip rule add prio 1000 lookup 300
root@net-test:/# ip rule add prio 1000 uidrange 100-200 lookup 300
RTNETLINK answers: File exists
root@net-test:/# ip rule add prio 1000 uidrange 100-199 lookup 100
root@net-test:/# ip rule add prio 1000 uidrange 200-299 lookup 200
root@net-test:/# ip rule add prio 1000 uidrange 300-399 lookup 100
RTNETLINK answers: File exists
Tested: https://android-review.googlesource.com/#/c/299980/
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not set sk_err when dequeuing errors from the error queue.
Doing so results in:
a) Bugs: By overwriting existing sk_err values, it possibly
hides legitimate errors. It is also incorrect when local
errors are queued with ip_local_error. That happens in the
context of a system call, which already returns the error
code.
b) Inconsistent behavior: When there are pending errors on
the error queue, sk_err is sometimes 0 (e.g., for
the first timestamp on the error queue) and sometimes
set to an error code (after dequeuing the first
timestamp).
c) Suboptimality: Setting sk_err to ENOMSG on simple
TX timestamps can abort parallel reads and writes.
Removing this line doesn't break userspace. This is because
userspace code cannot rely on sk_err for detecting whether
there is something on the error queue. Except for ICMP messages
received for UDP and RAW, sk_err is not set at enqueue time,
and as a result sk_err can be 0 while there are plenty of
errors on the error queue.
For ICMP packets in UDP and RAW, sk_err is set when they are
enqueued on the error queue, but that does not result in aborting
reads and writes. For such cases, sk_err is only readable via
getsockopt(SO_ERROR) which will reset the value of sk_err on
its own. More importantly, prior to this patch,
recvmsg(MSG_ERRQUEUE) has a race on setting sk_err (i.e.,
sk_err is set by sock_dequeue_err_skb without atomic ops or
locks) which can store 0 in sk_err even when we have ICMP
messages pending. Removing this line from sock_dequeue_err_skb
eliminates that race.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag IFF_NO_QUEUE marks virtual device drivers that doesn't need a
default qdisc attached, given they will be backed by physical device,
that already have a qdisc attached for pushback.
It is still supported to attach a qdisc to a IFF_NO_QUEUE device, as
this can be useful for difference policy reasons (e.g. bandwidth
limiting containers). For this to work, the tx_queue_len need to have
a sane value, because some qdiscs inherit/copy the tx_queue_len
(namely, pfifo, bfifo, gred, htb, plug and sfb).
Commit a813104d92 ("IFF_NO_QUEUE: Fix for drivers not calling
ether_setup()") caught situations where some drivers didn't initialize
tx_queue_len. The problem with the commit was choosing 1 as the
fallback value.
A qdisc queue length of 1 causes more harm than good, because it
creates hard to debug situations for userspace. It gives userspace a
false sense of a working config after attaching a qdisc. As low
volume traffic (that doesn't activate the qdisc policy) works,
like ping, while traffic that e.g. needs shaping cannot reach the
configured policy levels, given the queue length is too small.
This patch change the value to DEFAULT_TX_QUEUE_LEN, given other
IFF_NO_QUEUE devices (that call ether_setup()) also use this value.
Fixes: a813104d92 ("IFF_NO_QUEUE: Fix for drivers not calling ether_setup()")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new argument is added to __skb_recv_datagram to provide
an explicit skb destructor, invoked under the receive queue
lock.
The UDP protocol uses such argument to perform memory
reclaiming on dequeue, so that the UDP protocol does not
set anymore skb->desctructor.
Instead explicit memory reclaiming is performed at close() time and
when skbs are removed from the receive queue.
The in kernel UDP protocol users now need to call a
skb_recv_udp() variant instead of skb_recv_datagram() to
properly perform memory accounting on dequeue.
Overall, this allows acquiring only once the receive queue
lock on dequeue.
Tested using pktgen with random src port, 64 bytes packet,
wire-speed on a 10G link as sender and udp_sink as the receiver,
using an l4 tuple rxhash to stress the contention, and one or more
udp_sink instances with reuseport.
nr sinks vanilla patched
1 440 560
3 2150 2300
6 3650 3800
9 4450 4600
12 6250 6450
v1 -> v2:
- do rmem and allocated memory scheduling under the receive lock
- do bulk scheduling in first_packet_length() and in udp_destruct_sock()
- avoid the typdef for the dequeue callback
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Define a new FIB rule attributes, FRA_UID_RANGE, to describe a
range of UIDs.
- Define a RTA_UID attribute for per-UID route lookups and dumps.
- Support passing these attributes to and from userspace via
rtnetlink. The value INVALID_UID indicates no UID was
specified.
- Add a UID field to the flow structures.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Protocol sockets (struct sock) don't have UIDs, but most of the
time, they map 1:1 to userspace sockets (struct socket) which do.
Various operations such as the iptables xt_owner match need
access to the "UID of a socket", and do so by following the
backpointer to the struct socket. This involves taking
sk_callback_lock and doesn't work when there is no socket
because userspace has already called close().
Simplify this by adding a sk_uid field to struct sock whose value
matches the UID of the corresponding struct socket. The semantics
are as follows:
1. Whenever sk_socket is non-null: sk_uid is the same as the UID
in sk_socket, i.e., matches the return value of sock_i_uid.
Specifically, the UID is set when userspace calls socket(),
fchown(), or accept().
2. When sk_socket is NULL, sk_uid is defined as follows:
- For a socket that no longer has a sk_socket because
userspace has called close(): the previous UID.
- For a cloned socket (e.g., an incoming connection that is
established but on which userspace has not yet called
accept): the UID of the socket it was cloned from.
- For a socket that has never had an sk_socket: UID 0 inside
the user namespace corresponding to the network namespace
the socket belongs to.
Kernel sockets created by sock_create_kern are a special case
of #1 and sk_uid is the user that created them. For kernel
sockets created at network namespace creation time, such as the
per-processor ICMP and TCP sockets, this is the user that created
the network namespace.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sending zero checksum is ok for TCP, but not for UDP.
UDPv6 receiver should by default drop a frame with a 0 checksum,
and UDPv4 would not verify the checksum and might accept a corrupted
packet.
Simply replace such checksum by 0xffff, regardless of transport.
This error was caught on SIT tunnels, but seems generic.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At accept() time, it is possible the parent has a non zero
sk_err_soft, leftover from a prior error.
Make sure we do not leave this value in the child, as it
makes future getsockopt(SO_ERROR) calls quite unreliable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for setting and using XPS when QoS via traffic
classes is enabled. With this change we will factor in the priority and
traffic class mapping of the packet and use that information to correctly
select the queue.
This allows us to define a set of queues for a given traffic class via
mqprio and then configure the XPS mapping for those queues so that the
traffic flows can avoid head-of-line blocking between the individual CPUs
if so desired.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the code for removing queues from the XPS map and makes
it so that we can apply the code any time we change either the number of
traffic classes or the mapping of a given block of queues. This way we
avoid having queues pulling traffic from a foreign traffic class.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a sysfs attribute for a Tx queue that allows us to determine the
traffic class for a given queue. This will allow us to more easily
determine this in the future. It is needed as XPS will take the traffic
class for a group of queues into account in order to avoid pulling traffic
from one traffic class into another.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions for configuring the traffic class to queue mappings have
other effects that need to be addressed. Instead of trying to export a
bunch of new functions just relocate the functions so that we can
instrument them directly with the functionality they will need.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Lots of fixes, mostly drivers as is usually the case.
1) Don't treat zero DMA address as invalid in vmxnet3, from Alexey
Khoroshilov.
2) Fix element timeouts in netfilter's nft_dynset, from Anders K.
Pedersen.
3) Don't put aead_req crypto struct on the stack in mac80211, from
Ard Biesheuvel.
4) Several uninitialized variable warning fixes from Arnd Bergmann.
5) Fix memory leak in cxgb4, from Colin Ian King.
6) Fix bpf handling of VLAN header push/pop, from Daniel Borkmann.
7) Several VRF semantic fixes from David Ahern.
8) Set skb->protocol properly in ip6_tnl_xmit(), from Eli Cooper.
9) Socket needs to be locked in udp_disconnect(), from Eric Dumazet.
10) Div-by-zero on 32-bit fix in mlx4 driver, from Eugenia Emantayev.
11) Fix stale link state during failover in NCSCI driver, from Gavin
Shan.
12) Fix netdev lower adjacency list traversal, from Ido Schimmel.
13) Propvide proper handle when emitting notifications of filter
deletes, from Jamal Hadi Salim.
14) Memory leaks and big-endian issues in rtl8xxxu, from Jes Sorensen.
15) Fix DESYNC_FACTOR handling in ipv6, from Jiri Bohac.
16) Several routing offload fixes in mlxsw driver, from Jiri Pirko.
17) Fix broadcast sync problem in TIPC, from Jon Paul Maloy.
18) Validate chunk len before using it in SCTP, from Marcelo Ricardo
Leitner.
19) Revert a netns locking change that causes regressions, from Paul
Moore.
20) Add recursion limit to GRO handling, from Sabrina Dubroca.
21) GFP_KERNEL in irq context fix in ibmvnic, from Thomas Falcon.
22) Avoid accessing stale vxlan/geneve socket in data path, from
Pravin Shelar"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (189 commits)
geneve: avoid using stale geneve socket.
vxlan: avoid using stale vxlan socket.
qede: Fix out-of-bound fastpath memory access
net: phy: dp83848: add dp83822 PHY support
enic: fix rq disable
tipc: fix broadcast link synchronization problem
ibmvnic: Fix missing brackets in init_sub_crq_irqs
ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"
arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold
net/mlx4_en: Save slave ethtool stats command
net/mlx4_en: Fix potential deadlock in port statistics flow
net/mlx4: Fix firmware command timeout during interrupt test
net/mlx4_core: Do not access comm channel if it has not yet been initialized
net/mlx4_en: Fix panic during reboot
net/mlx4_en: Process all completions in RX rings after port goes up
net/mlx4_en: Resolve dividing by zero in 32-bit system
net/mlx4_core: Change the default value of enable_qos
net/mlx4_core: Avoid setting ports to auto when only one port type is supported
net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec
...
netdev_walk_all_lower_dev is not properly walking the lower device
list. Commit 1a3f060c1a made netdev_walk_all_lower_dev similar
to netdev_walk_all_upper_dev_rcu and netdev_walk_all_lower_dev_rcu
but failed to update its netdev_next_lower_dev iterator. This patch
fixes that.
Fixes: 1a3f060c1a ("net: Introduce new api for walking upper and
lower devices")
Reported-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When transmitting on a packet socket with PACKET_VNET_HDR and
PACKET_QDISC_BYPASS, validate device support for features requested
in vnet_hdr.
Drop TSO packets sent to devices that do not support TSO or have the
feature disabled. Note that the latter currently do process those
packets correctly, regardless of not advertising the feature.
Because of SKB_GSO_DODGY, it is not sufficient to test device features
with netif_needs_gso. Full validate_xmit_skb is needed.
Switch to software checksum for non-TSO packets that request checksum
offload if that device feature is unsupported or disabled. Note that
similar to the TSO case, device drivers may perform checksum offload
correctly even when not advertising it.
When switching to software checksum, packets hit skb_checksum_help,
which has two BUG_ON checksum not in linear segment. Packet sockets
always allocate at least up to csum_start + csum_off + 2 as linear.
Tested by running github.com/wdebruij/kerneltools/psock_txring_vnet.c
ethtool -K eth0 tso off tx on
psock_txring_vnet -d $dst -s $src -i eth0 -l 2000 -n 1 -q -v
psock_txring_vnet -d $dst -s $src -i eth0 -l 2000 -n 1 -q -v -N
ethtool -K eth0 tx off
psock_txring_vnet -d $dst -s $src -i eth0 -l 1000 -n 1 -q -v -G
psock_txring_vnet -d $dst -s $src -i eth0 -l 1000 -n 1 -q -v -G -N
v2:
- add EXPORT_SYMBOL_GPL(validate_xmit_skb_list)
Fixes: d346a3fae3 ("packet: introduce PACKET_QDISC_BYPASS socket option")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
No one can see these events, because a network namespace can not be
destroyed, if it has sockets.
Unlike other devices, uevent-s for network devices are generated
only inside their network namespaces. They are filtered in
kobj_bcast_filter()
My experiments shows that net namespaces are destroyed more 30% faster
with this optimization.
Here is a perf output for destroying network namespaces without this
patch.
- 94.76% 0.02% kworker/u48:1 [kernel.kallsyms] [k] cleanup_net
- 94.74% cleanup_net
- 94.64% ops_exit_list.isra.4
- 41.61% default_device_exit_batch
- 41.47% unregister_netdevice_many
- rollback_registered_many
- 40.36% netdev_unregister_kobject
- 14.55% device_del
+ 13.71% kobject_uevent
- 13.04% netdev_queue_update_kobjects
+ 12.96% kobject_put
- 12.72% net_rx_queue_update_kobjects
kobject_put
- kobject_release
+ 12.69% kobject_uevent
+ 0.80% call_netdevice_notifiers_info
+ 19.57% nfsd_exit_net
+ 11.15% tcp_net_metrics_exit
+ 8.25% rpcsec_gss_exit_net
It's very critical to optimize the exit path for network namespaces,
because they are destroyed under net_mutex and many namespaces can be
destroyed for one iteration.
v2: use dev_set_uevent_suppress()
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc warns about an uninitialized pointer dereference in the vlan
priority handling:
net/core/flow_dissector.c: In function '__skb_flow_dissect':
net/core/flow_dissector.c:281:61: error: 'vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
As pointed out by Jiri Pirko, the variable is never actually used
without being initialized first as the only way it end up uninitialized
is with skb_vlan_tag_present(skb)==true, and that means it does not
get accessed.
However, the warning hints at some related issues that I'm addressing
here:
- the second check for the vlan tag is different from the first one
that tests the skb for being NULL first, causing both the warning
and a possible NULL pointer dereference that was not entirely fixed.
- The same patch that introduced the NULL pointer check dropped an
earlier optimization that skipped the repeated check of the
protocol type
- The local '_vlan' variable is referenced through the 'vlan' pointer
but the variable has gone out of scope by the time that it is
accessed, causing undefined behavior
Caching the result of the 'skb && skb_vlan_tag_present(skb)' check
in a local variable allows the compiler to further optimize the
later check. With those changes, the warning also disappears.
Fixes: 3805a938a6 ("flow_dissector: Check skb for VLAN only if skb specified.")
Fixes: d5709f7ab7 ("flow_dissector: For stripped vlan, get vlan info from skb->vlan_tci")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Eric Garver <e@erig.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now genl_register_family() is the only thing (other than the
users themselves, perhaps, but I didn't find any doing that)
writing to the family struct.
In all families that I found, genl_register_family() is only
called from __init functions (some indirectly, in which case
I've add __init annotations to clarifly things), so all can
actually be marked __ro_after_init.
This protects the data structure from accidental corruption.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of providing macros/inline functions to initialize
the families, make all users initialize them statically and
get rid of the macros.
This reduces the kernel code size by about 1.6k on x86-64
(with allyesconfig).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static family IDs have never really been used, the only
use case was the workaround I introduced for those users
that assumed their family ID was also their multicast
group ID.
Additionally, because static family IDs would never be
reserved by the generic netlink code, using a relatively
low ID would only work for built-in families that can be
registered immediately after generic netlink is started,
which is basically only the control family (apart from
the workaround code, which I also had to add code for so
it would reserve those IDs)
Thus, anything other than GENL_ID_GENERATE is flawed and
luckily not used except in the cases I mentioned. Move
those workarounds into a few lines of code, and then get
rid of GENL_ID_GENERATE entirely, making it more robust.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port_type_set() is been called and the new port type set is the same
as the old one, just return success.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_mutex can be locked for a long time. It may be because many
namespaces are being destroyed or many processes decide to create
a network namespace.
Both these operations are heavy, so it is better to have an ability to
kill a process which is waiting net_mutex.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use case is mainly for soreuseport to select sockets for the local
numa node, but since generic, lets also add this for other networking
and tracing program types.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
