As Arnaldo Carvalho de Melo points out I should be using list_entry in case
the structure changes in future. Current code functions but is reliant
on position and requires type cast.
Noticed when doing this that I have one more variable than I needed so
removing that also.
Signed off by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes CCID3 to give much closer performance to RFC4342.
CCID3 is meant to alter sending rate based on RTT and loss.
The performance was verified against:
http://wand.net.nz/~perry/max_download.php
For example I tested with netem and had the following parameters:
Delayed Acks 1, MSS 256 bytes, RTT 105 ms, packet loss 5%.
This gives a theoretical speed of 71.9 Kbits/s. I measured across three
runs with this patch set and got 70.1 Kbits/s. Without this patchset the
average was 232 Kbits/s which means Linux can't be used for CCID3 research
properly.
I also tested with netem turned off so box just acting as router with 1.2
msec RTT. The performance with this is the same with or without the patch
at around 30 Mbit/s.
Signed off by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
And not the silly LIMIT_NETDEBUG and silently return without inserting
the option requested.
Also drop some old debugging messages associated to option insertion.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I guess I forgot to add it, nah, now it just works:
18:04:33.274066 IP6 ::1.1476 > ::1.5001: request (service=0)
18:04:33.334482 IP6 ::1.5001 > ::1.1476: reset (code=bad_service_code)
Ditched IP_DCCP_UNLOAD_HACK, as now we would have to do it for both
IPv6 and IPv4, so I'll come up with another way for freeing the
control sockets in upcoming changesets.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also fixes the layout of dccp_hdr short sequence numbers, problem
was not fatal now as we only support long (48 bits) sequence numbers.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. No need for ->ccid_init nor ->ccid_exit, this is what module_{init,exit}
does and anynways neither ccid2 nor ccid3 were using it.
2. Rename struct ccid to struct ccid_operations and introduce struct ccid
with a pointer to ccid_operations and rigth after it the rx or tx
private state.
3. Remove the pointer to the state of the half connections from struct
dccp_sock, now its derived thru ccid_priv() from the ccid pointer.
Now we also can implement the setsockopt for changing the CCID easily as
no ccid init routines can affect struct dccp_sock in any way that prevents
other CCIDs from working if a CCID switch operation is asked by apps.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing if the ccid being instantiated has these methods in
ccid_init().
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare circumstances 0 is returned by dccp_li_hist_calc_i_mean which
leads to a divide by zero in ccid3_hc_rx_packet_recv. Explicitly check
for zero return now. Update copyright notice at same time.
Found by Arnaldo.
Signed-off-by: Ian McDonald <imcdnzl@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocation for the optnames is similar to the DCCP options, with a
range for rx and tx half connection CCIDs.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also use some BUG_ON where appropriate and use LIMIT_NETDEBUG for the unlikely
cases where we, at this stage, want to know about, that in my tests hasn't
appeared in the radar.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
To match more closely what is described in RFC 3448.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: Ian McDonald <iam4@cs.waikato.ac.nz>
To start the timestamps with 0.0ms, easing the integer maths in the CCIDs, this
probably will be reworked to use the to be introduced struct timeval_offset
infrastructure out of skb_get_timestamp, etc.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
The initialization of ccid3hcrx_rtt to 5ms is just a bandaid, I'll continue
auditing the CCID3 HC rx codebase to fix this properly, probably I'll add a
feedback timer as suggested in the CCID3 draft.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This makes the send rate calculations behave way more closely to what
is specified, with the jitter previously seen on x and x_recv
disappearing completely on non lossy setups.
This resembles the tcp_data_snd_check code, that possibly we'll end up
using in DCCP as well, perhaps moving this code to
inet_connection_sock.
For now I'm doing the simplest implementation tho.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that applications can set dccp_sock->dccps_pkt_size, that in turn
is used in the CCID3 half connection init routines to set
ccid3hc[tr]x_s and use it in its rate calculations.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renaming it to dccp_rx_hist_detect_loss.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renaming it to dccp_rx_hist_add_packet.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And put this into net/dccp/ccids/lib/, where packet_history.[ch] will also be
moved and then we'll have a tfrc_lib.ko module that will be used by
dccp_ccid3.ko and other CCIDs that are variations of TFRC (RFC 3448).
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid open coding this all over the place.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introducing functions to add to or subtract from a timeval variable
and renaming now_delta to timeval_new_delta that calls do_gettimeofday
and then timeval_delta, that should be used when there are several
deltas made relative to the current time or setting variables to it,
so as to avoid calling do_gettimeofday excessively.
I'm leaving these "timeval_" prefixed funcions internal to DCCP for a
while till we're sure there are no subtle bugs in it.
It also is more correct as it checks if the number of usecs added to
or subtracted from a tv_usec field is more than 2 seconds.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not quite what I think we should have long term but improves
performance for now, so lets use it till we get CCID3 working well,
then we can think about using sk_write_queue, perhaps using some ideas
from Juwen Lai's old stack for 2.4.20.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch puts mostly read only data in the right section
(read_mostly), to help sharing of these data between CPUS without
memory ping pongs.
On one of my production machine, tcp_statistics was sitting in a
heavily modified cache line, so *every* SNMP update had to force a
reload.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And also hc_tx and hc_rx get_info functions for the CCIDs to fill in
information that is specific to them.
For now reusing struct tcp_info, later I'll try to figure out a better
solution, for now its really nice to get this kind of info:
[root@qemu ~]# ./ss -danemi
State Recv-Q Send-Q Local Addr:Port Peer Addr:Port
LISTEN 0 0 *:5001 *:* ino:628 sk:c1340040
mem:(r0,w0,f0,t0) cwnd:0 ssthresh:0
ESTAB 0 0 172.20.0.2:5001 172.20.0.1:32785 ino:629 sk:c13409a0
mem:(r0,w0,f0,t0) ts rto:1000 rtt:0.004/0 cwnd:0 ssthresh:0 rcv_rtt:61.377
This, for instance, shows that we're not congestion controlling ACKs,
as the above output is in the ttcp receiving host, and ttcp is a one
way app, i.e. the received never calls sendmsg, so
ccid_hc_tx_send_packet is never called, so the TX half connection
stays in TFRC_SSTATE_NO_SENT state and hctx_rtt is never calculated,
stays with the value set in ccid3_hc_tx_init, 4us, as show above in
milliseconds (0.004ms), upcoming patches will fix this.
rcv_rtt seems sane tho, matching ping results :-)
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using TIMESTAMP_ECHO and ELAPSED_TIME options received.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CCID3 keeps this variable in usecs, inet_connection_socks in jiffies,
so to avoid Mars orbiter losses lets reintroduce ccid3hctx_t_rto 8)
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes timestamp, timestamp echo, and elapsed time to use units of 10
usecs as per DCCP spec. This has been tested to verify that times are correct.
Also fixed up length and used hton/ntoh more.
Still to add in later patches:
- actually use elapsed time to adjust RTT
(commented out as was prior to this patch)
- send options at times more closely following the spec
(content is now correct)
Signed-off-by: Ian McDonald <iam4@cs.waikato.ac.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
may be a false warning if there always is something on ccid3hcrx_hist:
net/dccp/ccids/ccid3.c: In function 'ccid3_hc_rx_packet_recv':
net/dccp/ccids/ccid3.c:1634: warning: 'tstamp.tv_usec' may be used uninitialized in this function
net/dccp/ccids/ccid3.c:1634: warning: 'tstamp.tv_sec' may be used uninitialized in this function
const on inline functions doesn't have any effect:
net/dccp/dccp.h:64: warning: type qualifiers ignored on function return type
net/dccp/dccp.h:70: warning: type qualifiers ignored on function return type
net/dccp/dccp.h:76: warning: type qualifiers ignored on function return type
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only available if CONFIG_DEBUG_KERNEL is enabled in the "Kernel
Hacking" Menu.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As requested by Ian.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: Ian McDonald <iam4@cs.waikato.ac.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also changes the list_for_each_entry_safe_continue behaviour to match its
kerneldoc comment, that is, to start after the pos passed.
Also adds several helper functions from previously open coded fragments, making
the code more clear.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This way it gets closer to the TCP flow, where congestion window
checks are done, it seems we can map ccid_hc_tx_send_packet in
dccp_write_xmit to tcp_snd_wnd_test in tcp_write_xmit, a CCID2
decision should just fit in here as well...
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Development to this point was done on a subversion repository at:
http://oops.ghostprotocols.net:81/cgi-bin/viewcvs.cgi/dccp-2.6/
This repository will be kept at this site for the foreseable future,
so that interested parties can see the history of this code,
attributions, etc.
If I ever decide to take this offline I'll provide the full history at
some other suitable place.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
