vcpu->arch.mce_banks is malloc in kvm_arch_vcpu_init(), but
never free in any place, this may cause memory leak. So this
patch fixed to free it in kvm_arch_vcpu_uninit().
Cc: stable@kernel.org
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Exit the guest pagetable walk loop if reading gpte failed. Otherwise its
possible to enter an endless loop processing the previous present pte.
Cc: stable@kernel.org
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When found a error hva, should not return PAGE_SIZE but the level...
Also clean up the coding style of the following loop.
Cc: stable@kernel.org
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When we queue an interrupt to the local apic, we set the IRR before the TMR.
The vcpu can pick up the IRR and inject the interrupt before setting the TMR,
and perhaps even EOI it, causing incorrect behaviour.
The race is really insignificant since it can only occur on the first
interrupt (usually following interrupts will not change TMR), but it's better
closed than open.
Fixed by reordering setting the TMR vs IRR.
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
CONFIG_X86_CPU_DEBUG, which provides some parsed versions of the x86
CPU configuration via debugfs, has caused boot failures on real
hardware. The value of this feature has been marginal at best, as all
this information is already available to userspace via generic
interfaces.
Causes crashes that have not been fixed + minimal utility -> remove.
See the referenced LKML thread for more information.
Reported-by: Ozan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <alpine.LFD.2.00.1001221755320.13231@localhost.localdomain>
Cc: Jaswinder Singh Rajput <jaswinder@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: <stable@kernel.org>
Commit d1c84f79a6
leads to a regression when microcode_amd.c is compiled into the kernel.
It causes a big boot delay because the firmware is not available.
See http://marc.info/?l=linux-kernel&m=126267290920060
It also renders the reload sysfs attribute useless.
Fixing this is too intrusive for an -rc5 kernel.
Thus I'd like to restore the microcode loading behaviour of kernel
2.6.32.
CC: Gene Heskett <gene.heskett@verizon.net>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20100122203456.GB13792@alberich.amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
HPET MSI on platforms with ATI SB700/SB800 as they seem to have some
side-effects on floppy DMA. Do not use HPET MSI on such platforms.
Original problem report from Mark Hounschell
http://lkml.indiana.edu/hypermail/linux/kernel/0912.2/01118.html
[ This patch needs to go to stable as well. But, there are some
conflicts that prevents the patch from going as is. I can
rebase/resubmit to stable once the patch goes upstream.
hpa: still Cc:'ing stable@ as an FYI. ]
Tested-by: Mark Hounschell <markh@compro.net>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: <stable@kernel.org>
LKML-Reference: <20100121190952.GA32523@linux-os.sc.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
nodes_possible_map does not currently include nodes that have SRAT
entries that are all ACPI_SRAT_MEM_HOT_PLUGGABLE since the bit is
cleared in nodes_parsed if it does not have an online address range.
Unequivocally setting the bit in nodes_parsed is insufficient since
existing code, such as acpi_get_nodes(), assumes all nodes in the map
have online address ranges. In fact, all code using nodes_parsed
assumes such nodes represent an address range of online memory.
nodes_possible_map is created by unioning nodes_parsed and
cpu_nodes_parsed; the former represents nodes with online memory and
the latter represents memoryless nodes. We now set the bit for
hotpluggable nodes in cpu_nodes_parsed so that it also gets set in
nodes_possible_map.
[ hpa: Haicheng Li points out that this makes the naming of the
variable cpu_nodes_parsed somewhat counterintuitive. However, leave
it as is in the interest of keeping the pure bug fix patch small. ]
Signed-off-by: David Rientjes <rientjes@google.com>
Tested-by: Haicheng Li <haicheng.li@linux.intel.com>
LKML-Reference: <alpine.DEB.2.00.1001201152040.30528@chino.kir.corp.google.com>
Cc: <stable@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Deassigning a device from the passthrough domain does not
work and breaks device assignment to kvm guests. This patch
fixes the issue.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch moves the initialization of the iommu-api out of
the dma-ops initialization code. This ensures that the
iommu-api is initialized even with iommu=pt.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
In the __detach_device function the reference count for a
device-domain binding may become zero. This results in the
device being removed from the domain and dev_data->domain
will be NULL. This is bad because this pointer is
dereferenced when trying to unlock the domain->lock. This
patch fixes the issue by keeping the domain in a seperate
variable.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The variable i in this function could be increased to over
2**32 which would result in an integer overflow when using
int. Fix it by changing i to unsigned long.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: x86: Add support for the ANY bit
perf: Change the is_software_event() definition
perf: Honour event state for aux stream data
perf: Fix perf_event_do_pending() fallback callsite
perf kmem: Print usage help for unknown commands
perf kmem: Increase "Hit" column length
hw-breakpoints, perf: Fix broken mmiotrace due to dr6 by reference change
perf timechart: Use tid not pid for COMM change
Propagate the ANY bit into the fixed counter config for v3 and higher.
Signed-off-by: Stephane Eranian <eranian@google.com>
[a.p.zijlstra@chello.nl: split from larger patch]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <4b5430c6.0f975e0a.1bf9.ffff85fe@mx.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We can use logical flat mode if there are <= 8 logical cpu's
(irrespective of physical apic id values). This will enable simplified
and efficient IPI and device interrupt routing on such platforms.
This has been tested to work on both Intel and AMD platforms.
Exceptions like IBM summit platform which can't use logical flat mode
are addressed by using OEM platform checks.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Chris McDermott <lcm@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chris McDermott from IBM confirmed that hurricane chipset in IBM summit
platforms doesn't support logical flat mode. Irrespective of the other
things like apic_id's, total number of logical cpu's, Linux kernel
should default to physical mode for this system.
The 32-bit kernel does so using the OEM checks for the IBM summit
platform. Add a similar OEM platform check for the 64bit kernel too.
Otherwise the linux kernel boot can hang on this platform under certain
bios/platform settings.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Chris McDermott <lcm@linux.vnet.ibm.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 62edab9056 (from June 2009
but merged in 2.6.33) changes notify_die to pass dr6 by
reference.
However, it forgets to fix the check for DR_STEP in kmmio.c,
breaking mmiotrace. It also passes a wrong value to the post
handler.
This simple fix makes mmiotrace work again.
Signed-off-by: Luca Barbieri <luca@luca-barbieri.com>
Acked-by: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <1263634770-14578-1-git-send-email-luca@luca-barbieri.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, uv: Ensure hub revision set for all ACPI modes.
x86, uv: Add function retrieving node controller revision number
x86: xen: 64-bit kernel RPL should be 0
x86: kernel_thread() -- initialize SS to a known state
x86/agp: Fix agp_amd64_init and agp_amd64_cleanup
x86: SGI UV: Fix mapping of MMIO registers
x86: mce.h: Fix warning in header checks
Ensure that UV hub revision is set for all ACPI modes.
Signed-off-by: Russ Anderson <rja@sgi.com>
LKML-Reference: <20100115180908.GB7757@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add function for determining the revision id of the SGI UV
node controller chip (HUB). This function is needed in a
subsequent patch.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20100112210904.GA24546@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Easy fix for a regression introduced in 2.6.31.
On managed CPUs the cpufreq.c core will call driver->exit(cpu) on the
managed cpus and powernow_k8 will free the core's data.
Later driver->get(cpu) function might get called trying to read out the
current freq of a managed cpu and the NULL pointer check does not work on
the freed object -> better set it to NULL.
->get() is unsigned and must return 0 as invalid frequency.
Reference:
http://bugzilla.kernel.org/show_bug.cgi?id=14391
Signed-off-by: Thomas Renninger <trenn@suse.de>
Tested-by: Michal Schmidt <mschmidt@redhat.com>
CC: stable@kernel.org
Signed-off-by: Dave Jones <davej@redhat.com>
Under Xen 64 bit guests actually run their kernel in ring 3,
however the hypervisor takes care of squashing descriptor the
RPLs transparently (in order to allow them to continue to
differentiate between user and kernel space CS using the RPL).
Therefore the Xen paravirt backend should use RPL==0 instead of
1 (or 3). Using RPL==1 causes generic arch code to take
incorrect code paths because it uses "testl $3, <CS>, je foo"
type tests for a userspace CS and this considers 1==userspace.
This issue was previously masked because get_kernel_rpl() was
omitted when setting CS in kernel_thread(). This was fixed when
kernel_thread() was unified with 32 bit in
f443ff4201.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Christian Kujau <lists@nerdbynature.de>
Cc: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <1263377768-19600-2-git-send-email-ian.campbell@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Before the kernel_thread was converted into "C" we had
pt_regs::ss set to __KERNEL_DS (by SAVE_ALL asm macro).
Though I must admit I didn't find any *explicit* load of
%ss from this structure the better to be on a safe side
and set it to a known value.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Christian Kujau <lists@nerdbynature.de>
Cc: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com>
Cc: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <1263377768-19600-1-git-send-email-ian.campbell@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This fixes the regression introduced by the commit
f405d2c023.
The above commit fixes the following issue:
http://marc.info/?l=linux-kernel&m=126192729110083&w=2
However, it doesn't work properly when you remove and insert the
agp_amd64 module again.
agp_amd64_init() and agp_amd64_cleanup should be called only
when gart_iommu is not called earlier (that is, the GART IOMMU
is not enabled). We need to use 'gart_iommu_aperture' to see if
GART IOMMU is enabled or not.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: mitov@issp.bas.bg
Cc: davej@redhat.com
LKML-Reference: <20100104161603L.fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This fixes the problem of the initialization code not correctly
mapping the entire MMIO space on a UV system. A side effect is
the map_high() interface needed to be changed to accommodate
different address and size shifts.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Mike Habeck <habeck@sgi.com>
Cc: <stable@kernel.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <4B479202.7080705@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Someone isn't reading their build output: Move the definition
out of the exported header.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: linux-kernel@vger.kernelorg
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While processing kernel perf callchains, an bad entry can be
considered as a valid stack pointer but not as a kernel address.
In this case, we hang in an endless loop. This can happen in an
x86-32 kernel after processing the last entry in a kernel
stacktrace.
Just stop the stack frame walking after we encounter an invalid
kernel address.
This fixes a hard lockup in x86-32.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1262227945-27014-1-git-send-regression-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Revert commit 2fbd07a5f5, as this commit
breaks an IBM platform with quad-core Xeon cpu's.
According to Suresh, this might be an IBM platform issue, as on other
Intel platforms with <= 8 logical cpu's, logical flat mode works fine
irespective of physical apic id values (inline with the xapic
architecture).
Revert this for now because of the IBM platform breakage.
Another version will be re-submitted after the complete analysis.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The list macros use LIST_POISON1 and LIST_POISON2 as undereferencable
pointers in order to trap erronous use of freed list_heads. Unfortunately
userspace can arrange for those pointers to actually be dereferencable,
potentially turning an oops to an expolit.
To avoid this allow architectures (currently x86_64 only) to override
the default values for these pointers with truly-undereferencable values.
This is easy on x86_64 as the virtual address space is large and contains
areas that cannot be mapped.
Other 64-bit architectures will likely find similar unmapped ranges.
[ingo: switch to 0xdead000000000000 as the unmapped area]
[ingo: add comments, cleanup]
[jaswinder: eliminate sparse warnings]
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The necessary changes to the x86 Kconfig and boot/compressed to allow the
use of this new compression method
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Makes it consistent with the extern declaration, used when CONFIG_HIGHMEM
is set Removes redundant casts in printout messages
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
x86, irq: Check move_in_progress before freeing the vector mapping
x86: copy_from_user() should not return -EFAULT
Revert "x86: Side-step lguest problem by only building cmpxchg8b_emu for pre-Pentium"
x86/pci: Intel ioh bus num reg accessing fix
x86: Fix size for ex trampoline with 32bit
cleanup only.
setup_arch(), doesn't care care if ACPI initialization succeeded
or failed, so delete acpi_boot_table_init()'s return value.
Signed-off-by: Len Brown <len.brown@intel.com>
With the recent irq migration fixes (post 2.6.32), Gary Hade has noticed
"No IRQ handler for vector" messages during the 2.6.33-rc1 kernel boot on IBM
AMD platforms and root caused the issue to this commit:
> commit 23359a88e7
> Author: Suresh Siddha <suresh.b.siddha@intel.com>
> Date: Mon Oct 26 14:24:33 2009 -0800
>
> x86: Remove move_cleanup_count from irq_cfg
As part of this patch, we have removed the move_cleanup_count check
in smp_irq_move_cleanup_interrupt(). With this change, we can run into a
situation where an irq cleanup interrupt on a cpu can cleanup the vector
mappings associated with multiple irqs, of which one of the irq's migration
might be still in progress. As such when that irq hits the old cpu, we get
the "No IRQ handler" messages.
Fix this by checking for the irq_cfg's move_in_progress and if the move
is still in progress delay the vector cleanup to another irq cleanup
interrupt request (which will happen when the irq starts arriving at the
new cpu destination).
Reported-and-tested-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1262804191.2732.7.camel@sbs-t61.sc.intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This reverts commit ae1b22f6e4.
As Linus said in 982d007a6e: "There was something really messy about
cmpxchg8b and clone CPU's, so if you enable it on other CPUs later, do it
carefully."
This breaks lguest for those configs, but we can fix that by emulating
if we have to.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=14884
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Callers of copy_from_user() expect it to return the number of bytes
it could not copy. In no case it is supposed to return -EFAULT.
In case of a detected buffer overflow just return the requested
length. In addition one could think of a memset that would clear
the size of the target object.
[ hpa: code is not in .32 so not needed for -stable ]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
LKML-Reference: <20100105131911.GC5480@osiris.boeblingen.de.ibm.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This reverts commit ae1b22f6e4.
As Linus said in 982d007a6e: "There was something really messy about
cmpxchg8b and clone CPU's, so if you enable it on other CPUs later, do it
carefully."
This breaks lguest for those configs, but we can fix that by emulating
if we have to.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=14884
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <201001051248.49700.rusty@rustcorp.com.au>
Cc: stable@kernel.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
It is above 0x100 (PCI-Express extended register space), so if mmconf
is not enable, we can't access it.
[ hpa: changed the bound from 0x200 to 0x120, which is the tight
bound. ]
Reported-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1261525263-13763-3-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
fix for error that is introduced by
| x86: Use find_e820() instead of hard coded trampoline address
it should end with PAGE_SIZE + PAGE_SIZE
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1261525263-13763-2-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/agp: Fix agp_amd64_init() initialization with CONFIG_GART_IOMMU enabled
x86: SGI UV: Fix writes to led registers on remote uv hubs
x86, kmemcheck: Use KERN_WARNING for error reporting
x86: Use KERN_DEFAULT log-level in __show_regs()
x86, compress: Force i386 instructions for the decompressor
x86/amd-iommu: Fix initialization failure panic
dma-debug: Do not add notifier when dma debugging is disabled.
x86: Fix objdump version check in chkobjdump.awk for different formats.
Trivial conflicts in arch/x86/include/asm/uv/uv_hub.h due to me having
applied an earlier version of an SGI UV fix.
Pass the frame pointer from the regs of the interrupted path
to dump_trace() while processing the stack trace.
Currently, dump_trace() takes the current bp and starts the
callchain from dump_trace() itself. This is wasteful because
we need to walk through the entire NMI/DEBUG stack before
retrieving the interrupted point.
We can fix that by just using the frame pointer from the
captured regs. It points exactly where we want to start.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1262235183-5320-1-git-send-regression-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: introduce kernel parameter acpi_sleep=sci_force_enable
ACPI: WMI: Survive BIOS with duplicate GUIDs
dell-wmi - fix condition to abort driver loading
wmi: check find_guid() return value to prevent oops
dell-wmi, hp-wmi, msi-wmi: check wmi_get_event_data() return value
ACPI: hp-wmi, msi-wmi: clarify that wmi_install_notify_handler() returns an acpi_status
dell-wmi: sys_init_module: 'dell_wmi'->init suspiciously returned 21, it should
ACPI video: correct error-handling code
ACPI video: no warning message if "acpi_backlight=vendor" is used
ACPI: fix ACPI=n allmodconfig build
thinkpad-acpi: improve Kconfig help text
thinkpad-acpi: update volume subdriver documentation
thinkpad-acpi: make volume subdriver optional
thinkpad-acpi: don't fail to load the entire module due to ALSA problems
thinkpad-acpi: don't take the first ALSA slot by default
Introduce kernel parameter acpi_sleep=sci_force_enable
some laptop requires SCI_EN being set directly on resume,
or else they hung somewhere in the resume code path.
We already have a blacklist for these laptops but we still need
this option, especially when debugging some suspend/resume problems,
in case there are systems that need this workaround and are not yet
in the blacklist.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI/cardbus: Add a fixup hook and fix powerpc
PCI: change PCI nomenclature in drivers/pci/ (non-comment changes)
PCI: change PCI nomenclature in drivers/pci/ (comment changes)
PCI: fix section mismatch on update_res()
PCI: add Intel 82599 Virtual Function specific reset method
PCI: add Intel USB specific reset method
PCI: support device-specific reset methods
PCI: Handle case when no pci device can provide cache line size hint
PCI/PM: Propagate wake-up enable for PCIe devices too
vgaarbiter: fix a typo in the vgaarbiter Documentation
* 'kvm-updates/2.6.33' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: get rid of kvm_create_vm() unused label warning on s390
KVM: powerpc: Fix mtsrin in book3s_64 mmu
KVM: ia64: fix build breakage due to host spinlock change
KVM: x86: Extend KVM_SET_VCPU_EVENTS with selective updates
KVM: LAPIC: make sure IRR bitmap is scanned after vm load
KVM: Fix possible circular locking in kvm_vm_ioctl_assign_device()
KVM: MMU: remove prefault from invlpg handler
The wrong address was being used to write the SCIR led regs on remote
hubs. Also, there was an inconsistency between how BIOS and the kernel
indexed these regs. Standardize on using the lower 6 bits of the APIC
ID as the index.
This patch fixes the problem of writing to an errant address to a
cpu # >= 64.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Jack Steiner <steiner@sgi.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The wrong address was being used to write the SCIR led regs on
remote hubs. Also, there was an inconsistency between how BIOS
and the kernel indexed these regs. Standardize on using the
lower 6 bits of the APIC ID as the index.
This patch fixes the problem of writing to an errant address to
a cpu # >= 64.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Jack Steiner <steiner@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@kernel.org
LKML-Reference: <4B3922F9.3060905@sgi.com>
[ v2: fix a number of annoying checkpatch artifacts and whitespace noise ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As suggested by Vegard Nossum, use KERN_WARNING for error
reporting to make sure kmemcheck reports end up in syslog.
Suggested-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <1261990935.4641.7.camel@penberg-laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Andrew Morton reported a strange looking kmemcheck warning:
WARNING: kmemcheck: Caught 32-bit read from uninitialized memory (ffff88004fba6c20)
0000000000000000310000000000000000000000000000002413000000c9ffff
u u u u u u u u u u u u u u u u i i i i i i i i u u u u u u u u
[<ffffffff810af3aa>] kmemleak_scan+0x25a/0x540
[<ffffffff810afbcb>] kmemleak_scan_thread+0x5b/0xe0
[<ffffffff8104d0fe>] kthread+0x9e/0xb0
[<ffffffff81003074>] kernel_thread_helper+0x4/0x10
[<ffffffffffffffff>] 0xffffffffffffffff
The above printout is missing register dump completely. The
problem here is that the output comes from syslog which doesn't
show KERN_INFO log-level messages. We didn't see this before
because both of us were testing on 32-bit kernels which use the
_default_ log-level.
Fix that up by explicitly using KERN_DEFAULT log-level for
__show_regs() printks.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <1261988819.4641.2.camel@penberg-laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
User space may not want to overwrite asynchronously changing VCPU event
states on write-back. So allow to skip nmi.pending and sipi_vector by
setting corresponding bits in the flags field of kvm_vcpu_events.
[avi: advertise the bits in KVM_GET_VCPU_EVENTS]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The vcpus are initialized with irr_pending set to false, but
loading the LAPIC registers with pending IRR fails to reset
the irr_pending variable.
Cc: stable@kernel.org
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The invlpg prefault optimization breaks Windows 2008 R2 occasionally.
The visible effect is that the invlpg handler instantiates a pte which
is, microseconds later, written with a different gfn by another vcpu.
The OS could have other mechanisms to prevent a present translation from
being used, which the hypervisor is unaware of.
While the documentation states that the cpu is at liberty to prefetch tlb
entries, it looks like this is not heeded, so remove tlb prefetch from
invlpg.
Cc: stable@kernel.org
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Recently, some distros have started shipping versions of gcc which
default to -march=i686. This breaks building kernels for pre-i686
machines, even if they have been selected in Kconfig, due to the
generation of CMOV instructions.
There isn't enough benefit to try to preserve the generation of these
instructions even when selected, so simply force -march=i386 for the
decompressor when building a 32-bit kernel.
Reported-and-tested-by: Chris Rankin <rankincj@yahoo.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <219280.97558.qm@web52907.mail.re2.yahoo.com>
This reverts commit 9f15226e75. It's just
wrong, and broke resume for Rafael even on a non-AMD CPU.
As Rafael says:
"... it causes microcode_init_cpu() to be called during resume even for
CPUs for which there's no microcode to apply. That, in turn, results
in executing request_firmware() (on Intel CPUs at least) which doesn't
work at this stage of resume (we have device interrupts disabled, I/O
devices are still suspended and so on).
If I'm not mistaken, the "if (uci->valid)" logic means "if that CPU is
known to us" , so before commit 9f15226e75 microcode_resume_cpu() was
called for all CPUs already in the system during suspend, which was
the right thing to do. The commit changed it so that the CPUs without
microcode to apply are now treated as "unknown", which is not quite
right.
The problem this commit attempted to solve has to be handled
differently."
Bisected-and -requested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Presently acpi-cpufreq will perform the MSR read on the first CPU in the
mask. That's inefficient if that CPU differs from the current CPU.
Because we have to perform a cross-CPU call, but we could have run the
rdmsr on the current CPU.
So switch to using the new smp_call_function_any(), which will perform the
call on the current CPU if that CPU is present in the mask (it is).
Cc: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jaswinder Singh Rajput <jaswinder@kernel.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The x86 and ia64 implementations of the function in $subject are
exactly the same.
Also, since the arch-specific implementations of setting _PDC have
been completely hollowed out, remove the empty shells.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The only thing arch-specific about calling _PDC is what bits get
set in the input obj_list buffer.
There's no need for several levels of indirection to twiddle those
bits. Additionally, since we're just messing around with a buffer,
we can simplify the interface; no need to pass around the entire
struct acpi_processor * just to get at the buffer.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Both x86 and ia64 initialize _PDC with mostly common bit settings.
Factor out the common settings and leave the arch-specific ones alone.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The x86 and ia64 implementations of arch_acpi_processor_init_pdc()
are almost exactly the same. The only difference is in what bits
they set in obj_list buffer.
Combine the boilerplate memory management code, and leave the
arch-specific bit twiddling in separate implementations.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
arch dependent helper function that tells us if we should attempt to
evaluate _PDC on this machine or not.
The x86 implementation assumes that the CPUs in the machine must be
homogeneous, and that you cannot mix CPUs of different vendors.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The assumption that acpi_table_parse passes the return value
of the hanlder function to the caller proved wrong
recently. The return value of the handler function is
totally ignored. This makes the initialization code for AMD
IOMMU buggy in a way that could cause a kernel panic on
initialization. This patch fixes the issue in the AMD IOMMU
driver.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf session: Make events_stats u64 to avoid overflow on 32-bit arches
hw-breakpoints: Fix hardware breakpoints -> perf events dependency
perf events: Dont report side-band events on each cpu for per-task-per-cpu events
perf events, x86/stacktrace: Fix performance/softlockup by providing a special frame pointer-only stack walker
perf events, x86/stacktrace: Make stack walking optional
perf events: Remove unused perf_counter.h header file
perf probe: Check new event name
kprobe-tracer: Check new event/group name
perf probe: Check whether debugfs path is correct
perf probe: Fix libdwarf include path for Debian
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, irq: Allow 0xff for /proc/irq/[n]/smp_affinity on an 8-cpu system
Makefile: Unexport LC_ALL instead of clearing it
x86: Fix objdump version check in arch/x86/tools/chkobjdump.awk
x86: Reenable TSC sync check at boot, even with NONSTOP_TSC
x86: Don't use POSIX character classes in gen-insn-attr-x86.awk
Makefile: set LC_CTYPE, LC_COLLATE, LC_NUMERIC to C
x86: Increase MAX_EARLY_RES; insufficient on 32-bit NUMA
x86: Fix checking of SRAT when node 0 ram is not from 0
x86, cpuid: Add "volatile" to asm in native_cpuid()
x86, msr: msrs_alloc/free for CONFIG_SMP=n
x86, amd: Get multi-node CPU info from NodeId MSR instead of PCI config space
x86: Add IA32_TSC_AUX MSR and use it
x86, msr/cpuid: Register enough minors for the MSR and CPUID drivers
initramfs: add missing decompressor error check
bzip2: Add missing checks for malloc returning NULL
bzip2/lzma/gzip: pre-boot malloc doesn't return NULL on failure
Different version of objdump says its version in different way;
GNU objdump 2.16.1
or
GNU objdump version 2.19.51.0.14-1.fc11 20090722
This patch uses the first argument which starts with a number
as version string.
Changes in v2:
- Remove unneeded increment.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
LKML-Reference: <20091218154012.16960.5113.stgit@dhcp-100-2-132.bos.redhat.com>
Suggested-by: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The kbuild's select command doesn't propagate through the config
dependencies.
Hence the current rules of hardware breakpoint's config can't
ensure perf can never be disabled under us.
We have:
config X86
selects HAVE_HW_BREAKPOINTS
config HAVE_HW_BREAKPOINTS
select PERF_EVENTS
config PERF_EVENTS
[...]
x86 will select the breakpoints but that won't propagate to perf
events. The user can still disable the latter, but it is
necessary for the breakpoints.
What we need is:
- x86 selects HAVE_HW_BREAKPOINTS and PERF_EVENTS
- HAVE_HW_BREAKPOINTS depends on PERF_EVENTS
so that we ensure PERF_EVENTS is enabled and frozen for x86.
This fixes the following kind of build errors:
In file included from arch/x86/kernel/hw_breakpoint.c:31:
include/linux/hw_breakpoint.h: In function 'hw_breakpoint_addr':
include/linux/hw_breakpoint.h:39: error: 'struct perf_event' has no member named 'attr'
v2: Select also ANON_INODES from x86, required for perf
Reported-by: Cyrill Gorcunov <gorcunov@gmail.com>
Reported-by: Michal Marek <mmarek@suse.cz>
Reported-by: Andrew Randrianasulu <randrik_a@yahoo.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
LKML-Reference: <1261010034-7786-1-git-send-regression-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
John Blackwood reported:
> on an older Dell PowerEdge 6650 system with 8 cpus (4 are hyper-threaded),
> and 32 bit (x86) kernel, once you change the irq smp_affinity of an irq
> to be less than all cpus in the system, you can never change really the
> irq smp_affinity back to be all cpus in the system (0xff) again,
> even though no error status is returned on the "/bin/echo ff >
> /proc/irq/[n]/smp_affinity" operation.
>
> This is due to that fact that BAD_APICID has the same value as
> all cpus (0xff) on 32bit kernels, and thus the value returned from
> set_desc_affinity() via the cpu_mask_to_apicid_and() function is treated
> as a failure in set_ioapic_affinity_irq_desc(), and no affinity changes
> are made.
set_desc_affinity() is already checking if the incoming cpu mask
intersects with the cpu online mask or not. So there is no need
for the apic op cpu_mask_to_apicid_and() to check again
and return BAD_APICID.
Remove the BAD_APICID return value from cpu_mask_to_apicid_and()
and also fix set_desc_affinity() to return -1 instead of using BAD_APICID
to represent error conditions (as cpu_mask_to_apicid_and() can return
logical or physical apicid values and BAD_APICID is really to represent
bad physical apic id).
Reported-by: John Blackwood <john.blackwood@ccur.com>
Root-caused-by: John Blackwood <john.blackwood@ccur.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1261103386.2535.409.camel@sbs-t61>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'cpumask-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
cpumask: rename tsk_cpumask to tsk_cpus_allowed
cpumask: don't recommend set_cpus_allowed hack in Documentation/cpu-hotplug.txt
cpumask: avoid dereferencing struct cpumask
cpumask: convert drivers/idle/i7300_idle.c to cpumask_var_t
cpumask: use modern cpumask style in drivers/scsi/fcoe/fcoe.c
cpumask: avoid deprecated function in mm/slab.c
cpumask: use cpu_online in kernel/perf_event.c
It says
Warning: objdump version is older than 2.19
Warning: Skipping posttest.
because it used the wrong field from `objdump -v':
akpm:/usr/src/25> /opt/crosstool/gcc-4.0.2-glibc-2.3.6/x86_64-unknown-linux-gnu/bin/x86_64-unknown-linux-gnu-objdump -v
GNU objdump 2.16.1
Copyright 2005 Free Software Foundation, Inc.
This program is free software; you may redistribute it under the terms of
the GNU General Public License. This program has absolutely no warranty.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <200912172326.nBHNQaQl024796@imap1.linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Masami Hiramatsu <mhiramat@redhat.com>
Commit 83ce4009 did the following change
If the TSC is constant and non-stop, also set it reliable.
But, there seems to be few systems that will end up with TSC warp across
sockets, depending on how the cpus come out of reset. Skipping TSC sync
test on such systems may result in time inconsistency later.
So, reenable TSC sync test even on constant and non-stop TSC systems.
Set, sched_clock_stable to 1 by default and reset it in
mark_tsc_unstable, if TSC sync fails.
This change still gives perf benefit mentioned in 83ce4009 for systems
where TSC is reliable.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20091217202702.GA18015@linux-os.sc.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'for-33' of git://repo.or.cz/linux-kbuild: (29 commits)
net: fix for utsrelease.h moving to generated
gen_init_cpio: fixed fwrite warning
kbuild: fix make clean after mismerge
kbuild: generate modules.builtin
genksyms: properly consider EXPORT_UNUSED_SYMBOL{,_GPL}()
score: add asm/asm-offsets.h wrapper
unifdef: update to upstream revision 1.190
kbuild: specify absolute paths for cscope
kbuild: create include/generated in silentoldconfig
scripts/package: deb-pkg: use fakeroot if available
scripts/package: add KBUILD_PKG_ROOTCMD variable
scripts/package: tar-pkg: use tar --owner=root
Kbuild: clean up marker
net: add net_tstamp.h to headers_install
kbuild: move utsrelease.h to include/generated
kbuild: move autoconf.h to include/generated
drop explicit include of autoconf.h
kbuild: move compile.h to include/generated
kbuild: drop include/asm
kbuild: do not check for include/asm-$ARCH
...
Fixed non-conflicting clean merge of modpost.c as per comments from
Stephen Rothwell (modpost.c had grown an include of linux/autoconf.h
that needed to be changed to generated/autoconf.h)
The loop condition is fragile: we compare an unsigned value to zero, and
then decrement it by something larger than one in the loop. All the
callers should be passing in appropriately aligned buffer lengths, but
it's better to just not rely on it, and have some appropriate defensive
loop limits.
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not all awk implementations (including the default awk in Ubuntu 9.10)
support POSIX character classes. Since x86-opcode-map.txt is plain
ASCII, we can just use explicit ranges for lower case, alphabetic, and
alphanumeric characters instead.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Masami Hiramatsu <mhiramat@redhat.com>
LKML-Reference: <adabphy750b.fsf@roland-alpha.cisco.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
It's just wasteful for stacktrace users like perf to walk
through every entries on the stack whereas these only accept
reliable ones, ie: that the frame pointer validates.
Since perf requires pure reliable stacktraces, it needs a stack
walker based on frame pointers-only to optimize the stacktrace
processing.
This might solve some near-lockup scenarios that can be triggered
by call-graph tracing timer events.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1261024834-5336-2-git-send-regression-fweisbec@gmail.com>
[ v2: fix for modular builds and small detail tidyup ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The current print_context_stack helper that does the stack
walking job is good for usual stacktraces as it walks through
all the stack and reports even addresses that look unreliable,
which is nice when we don't have frame pointers for example.
But we have users like perf that only require reliable
stacktraces, and those may want a more adapted stack walker, so
lets make this function a callback in stacktrace_ops that users
can tune for their needs.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1261024834-5336-1-git-send-regression-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Noone uses this wrapper yet, and Ingo asked that it be kept consistent
with current task_struct usage.
(One user crept in via linux-next: fixed)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <tj@kernel.org>
Due to recent changes wakeup and mptable, we run out of early
reservations on 32-bit NUMA. Thus, adjust the available number.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4B22D754.2020706@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Found one system that boot from socket1 instead of socket0, SRAT get rejected...
[ 0.000000] SRAT: Node 1 PXM 0 0-a0000
[ 0.000000] SRAT: Node 1 PXM 0 100000-80000000
[ 0.000000] SRAT: Node 1 PXM 0 100000000-2080000000
[ 0.000000] SRAT: Node 0 PXM 1 2080000000-4080000000
[ 0.000000] SRAT: Node 2 PXM 2 4080000000-6080000000
[ 0.000000] SRAT: Node 3 PXM 3 6080000000-8080000000
[ 0.000000] SRAT: Node 4 PXM 4 8080000000-a080000000
[ 0.000000] SRAT: Node 5 PXM 5 a080000000-c080000000
[ 0.000000] SRAT: Node 6 PXM 6 c080000000-e080000000
[ 0.000000] SRAT: Node 7 PXM 7 e080000000-10080000000
...
[ 0.000000] NUMA: Allocated memnodemap from 500000 - 701040
[ 0.000000] NUMA: Using 20 for the hash shift.
[ 0.000000] Adding active range (0, 0x2080000, 0x4080000) 0 entries of 3200 used
[ 0.000000] Adding active range (1, 0x0, 0x96) 1 entries of 3200 used
[ 0.000000] Adding active range (1, 0x100, 0x7f750) 2 entries of 3200 used
[ 0.000000] Adding active range (1, 0x100000, 0x2080000) 3 entries of 3200 used
[ 0.000000] Adding active range (2, 0x4080000, 0x6080000) 4 entries of 3200 used
[ 0.000000] Adding active range (3, 0x6080000, 0x8080000) 5 entries of 3200 used
[ 0.000000] Adding active range (4, 0x8080000, 0xa080000) 6 entries of 3200 used
[ 0.000000] Adding active range (5, 0xa080000, 0xc080000) 7 entries of 3200 used
[ 0.000000] Adding active range (6, 0xc080000, 0xe080000) 8 entries of 3200 used
[ 0.000000] Adding active range (7, 0xe080000, 0x10080000) 9 entries of 3200 used
[ 0.000000] SRAT: PXMs only cover 917504MB of your 1048566MB e820 RAM. Not used.
[ 0.000000] SRAT: SRAT not used.
the early_node_map is not sorted because node0 with non zero start come first.
so try to sort it right away after all regions are registered.
also fixs refression by 8716273c (x86: Export srat physical topology)
-v2: make it more solid to handle cross node case like node0 [0,4g), [8,12g) and node1 [4g, 8g), [12g, 16g)
-v3: update comments.
Reported-and-tested-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4B2579D2.3010201@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
xsave_cntxt_init() does something like:
cpuid(0xd, ..); // find out what features FP/SSE/.. etc are supported
xsetbv(); // enable the features known to OS
cpuid(0xd, ..); // find out the size of the context for features enabled
Depending on what features get enabled in xsetbv(), value of the
cpuid.eax=0xd.ecx=0.ebx changes correspondingly (representing the
size of the context that is enabled).
As we don't have volatile keyword for native_cpuid(), gcc 4.1.2
optimizes away the second cpuid and the kernel continues to use
the cpuid information obtained before xsetbv(), ultimately leading to kernel
crash on processors supporting more state than the legacy FP/SSE.
Add "volatile" for native_cpuid().
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1261009542.2745.55.camel@sbs-t61.sc.intel.com>
Cc: stable@kernel.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Randy Dunlap reported the following build error:
"When CONFIG_SMP=n, CONFIG_X86_MSR=m:
ERROR: "msrs_free" [drivers/edac/amd64_edac_mod.ko] undefined!
ERROR: "msrs_alloc" [drivers/edac/amd64_edac_mod.ko] undefined!"
This is due to the fact that <arch/x86/lib/msr.c> is conditioned on
CONFIG_SMP and in the UP case we have only the stubs in the header.
Fork off SMP functionality into a new file (msr-smp.c) and build
msrs_{alloc,free} unconditionally.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
LKML-Reference: <20091216231625.GD27228@liondog.tnic>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Use NodeId MSR to get NodeId and number of nodes per processor.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20091216144355.GB28798@alberich.amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Remark update_res from __init to __devinit as it is called also
from __devinit functions.
This patch removes the following warning message:
WARNING: vmlinux.o(.devinit.text+0x774a): Section mismatch
in reference from the function pci_root_bus_res() to the
function .init.text:update_res()
The function __devinit pci_root_bus_res() references
a function __init update_res().
If update_res is only used by pci_root_bus_res then
annotate update_res with a matching annotation.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Aristeu Sergio <arozansk@redhat.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: linux-pci@vger.kernel.org
Cc: x86@kernel.org
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (38 commits)
direct I/O fallback sync simplification
ocfs: stop using do_sync_mapping_range
cleanup blockdev_direct_IO locking
make generic_acl slightly more generic
sanitize xattr handler prototypes
libfs: move EXPORT_SYMBOL for d_alloc_name
vfs: force reval of target when following LAST_BIND symlinks (try #7)
ima: limit imbalance msg
Untangling ima mess, part 3: kill dead code in ima
Untangling ima mess, part 2: deal with counters
Untangling ima mess, part 1: alloc_file()
O_TRUNC open shouldn't fail after file truncation
ima: call ima_inode_free ima_inode_free
IMA: clean up the IMA counts updating code
ima: only insert at inode creation time
ima: valid return code from ima_inode_alloc
fs: move get_empty_filp() deffinition to internal.h
Sanitize exec_permission_lite()
Kill cached_lookup() and real_lookup()
Kill path_lookup_open()
...
Trivial conflicts in fs/direct-io.c
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix kprobes build with non-gawk awk
x86: Split swiotlb initialization into two stages
x86: Regex support and known-movable symbols for relocs, fix _end
x86, msr: Remove incorrect, duplicated code in the MSR driver
x86: Merge kernel_thread()
x86: Sync 32/64-bit kernel_thread
x86, 32-bit: Use same regs as 64-bit for kernel_thread_helper
x86, 64-bit: Use user_mode() to determine new stack pointer in copy_thread()
x86, 64-bit: Move kernel_thread to C
x86-64, paravirt: Call set_iopl_mask() on 64 bits
x86-32: Avoid pipeline serialization in PTREGSCALL1 and 2
x86: Merge sys_clone
x86, 32-bit: Convert sys_vm86 & sys_vm86old
x86: Merge sys_sigaltstack
x86: Merge sys_execve
x86: Merge sys_iopl
x86-32: Add new pt_regs stubs
cpumask: Use modern cpumask style in arch/x86/kernel/cpu/mcheck/mce-inject.c
* 'module' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
modpost: fix segfault with short symbol names
module: handle ppc64 relocating kcrctabs when CONFIG_RELOCATABLE=y
Kbuild: clear marker out of modpost
module: make MODULE_SYMBOL_PREFIX into a CONFIG option
ARM: unexport symbols used to implement floating point emulation
ARM: use unified discard definition in linker script
x86: don't export inline function
sparc64: don't export static inline pci_ functions
* hpux_pipe() - no need to take BKL
* sys32_pipe() in arch/x86/ia32 and xtensa_pipe() in arch/xtensa -
no need at all, since both functions are open-coded sys_pipe()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use bitmap library and kill some unused iommu helper functions.
1. s/iommu_area_free/bitmap_clear/
2. s/iommu_area_reserve/bitmap_set/
3. Use bitmap_find_next_zero_area instead of find_next_zero_area
This cannot be simple substitution because find_next_zero_area
doesn't check the last bit of the limit in bitmap
4. Remove iommu_area_free, iommu_area_reserve, and find_next_zero_area
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Create a function to generate the value that is written to the UV hub MMR
to cause an IPI interrupt to be sent. The function will be used in the
GRU message queue error recovery code that sends IPIs to nodes in remote
partitions.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The UV BIOS has moved the location of some of their pointers to the
"partition reserved page" from memory into a uv hub MMR. The GRU does not
support bcopy operations from MMR space so we need to special case the MMR
addresses using VLOAD operations.
Additionally, the BIOS call for registering a message queue watchlist has
removed the 'blade' value and eliminated the structure that was being
passed in. This is also reflected in this patch.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide a mechanism for determining if a global physical address is
pointing to a UV hub MMR.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The UV BIOS has been updated to implement some of our interface
functionality differently than originally expected. These patches update
the kernel to the bios implementation and include a few minor bug fixes
which prevent us from doing significant testing on real hardware.
This patch:
For SGI UV systems, translate from a global physical address back to a
socket physical address. This does nothing to ensure the socket physical
address is actually addressable by the kernel. That is the responsibility
of the user of the function.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dma_mask is, when interpreted as address, the last valid byte, and hence
comparison msut also be done using the last valid of the buffer in
question.
Also fix the open-coded instances in lib/swiotlb.c.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Becky Bruce <beckyb@kernel.crashing.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently all architectures but microblaze unconditionally define
USE_ELF_CORE_DUMP. The microblaze omission seems like an error to me, so
let's kill this ifdef and make sure we are the same everywhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: <linux-arch@vger.kernel.org>
Cc: Michal Simek <michal.simek@petalogix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Suggested by Roland.
Unlike powepc, x86 always calls tracehook_report_syscall_exit(step) with
step = 0, and sends the trap by hand.
This results in unnecessary SIGTRAP when PTRACE_SINGLESTEP follows the
syscall-exit stop.
Change syscall_trace_leave() to pass the correct "step" argument to
tracehook and remove the send_sigtrap() logic.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Suggested by Roland.
Implement user_single_step_siginfo() for x86. Extract this code from
send_sigtrap().
Since x86 calls tracehook_report_syscall_exit(step => 0) the new helper is
not used yet.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
