SAL_CALL() always calls through the ia64_sal function pointer. I am adding
new functionality that needs the same conventions as SAL_CALL (FP regs
saved/restored, sal_lock acquired, etc), but doesn't use the ia64_sal
function pointer.
This patch pulls the body of SAL_CALL out into a new "IA64_FW_CALL" that
takes care of these calling conventions, but allows the caller to specify
either ia64_sal or some other firmware entry point.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* Make use of spaces and tabs consistent
* Make long line < 80col
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The check to see if the firmware drops interrupts during a
SAL_CACHE_FLUSH is done to early in the boot. SAL_CACHE_FLUSH expects
to be able to make PAL calls in virtual mode, on some cell based
machines a fault occurs causing a MCA. This patch moves the check
after mmu_context_init so the TLB and VHPT are properly setup.
Signed-off-by Troy Heber <troy.heber@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
If SAL_CACHE_FLUSH drops interrupts, complain about it and fall back to
using PAL_CACHE_FLUSH instead.
This is to work around a defect in HP rx5670 firmware: when an interrupt
occurs during SAL_CACHE_FLUSH, SAL drops the interrupt but leaves it marked
"in-service", which leaves the interrupt (and others of equal or lower
priority) masked.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
ERR_SEVERITY item is defined as a 8 bits item in SAL documentation
($B.2.1 rev december 2003), but as an u16 in sal.h.
This has the side effect that current code in mca.c may not call
ia64_sal_clear_state_info() upon receiving corrected platform errors
if there are bits set in the validation byte. Reported by Xavier Bru.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Version 3 - rediffed to apply on top of Ashok's hotplug cpu
patch. /proc/cpuinfo output in step with x86.
This is an updated MC/MT identification patch based on the
previous discussions on list.
Add the Multi-core and Multi-threading detection for IPF.
- Add new core and threading related fields in /proc/cpuinfo.
Physical id
Core id
Thread id
Siblings
- setup the cpu_core_map and cpu_sibling_map appropriately
- Handles Hot plug CPU
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Gordon Jin <gordon.jin@intel.com>
Signed-off-by: Rohit Seth <rohit.seth@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch is required to support cpu removal for IPF systems. Existing code
just fakes the real offline by keeping it run the idle thread, and polling
for the bit to re-appear in the cpu_state to get out of the idle loop.
For the cpu-offline to work correctly, we need to pass control of this CPU
back to SAL so it can continue in the boot-rendez mode. This gives the
SAL control to not pick this cpu as the monarch processor for global MCA
events, and addition does not wait for this cpu to checkin with SAL
for global MCA events as well. The handoff is implemented as documented in
SAL specification section 3.2.5.1 "OS_BOOT_RENDEZ to SAL return State"
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
