worse, we lock ->resource_lock too late when we are destroying the
final clonal VMA; the check for lack of other mappings of the same
opened file can race with mmap().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull i2c changes from Wolfram Sang:
- an arbitration driver. While the driver is quite simple, it caused
discussion if we need additional arbitration on top of the one
specified in the I2C standard. Conclusion is that I accept a few
generic mechanisms, but not very specific ones.
- the core lost the detach_adapter() call. It has no users anymore and
was in the way for other cleanups. attach_adapter() is sadly still
there since there are users waiting to be converted.
- the core gained a bus recovery infrastructure. I2C defines a way to
recover if the data line is stalled. This mechanism is now in the
core and drivers can now pass some data to make use of it.
- bigger driver cleanups for designware, s3c2410
- removing superfluous refcounting from drivers
- removing Ben Dooks as second maintainer due to inactivity. Thanks
for all your work so far, Ben!
- bugfixes, feature additions, devicetree fixups, simplifications...
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: xiic: must always write 16-bit words to TX_FIFO
i2c: octeon: use HZ in timeout value
i2c: octeon: Fix i2c fail problem when a process is terminated by a signal
i2c: designware-pci: drop superfluous {get|put}_device
i2c: designware-plat: drop superfluous {get|put}_device
i2c: davinci: drop superfluous {get|put}_device
MAINTAINERS: Ben Dooks is inactive regarding I2C
i2c: mux: Add i2c-arb-gpio-challenge 'mux' driver
i2c: at91: convert to dma_request_slave_channel_compat()
i2c: mxs: do error checking and handling in PIO mode
i2c: mxs: remove races in PIO code
i2c-designware: switch to use runtime PM autosuspend
i2c-designware: use usleep_range() in the busy-loop
i2c-designware: enable/disable the controller properly
i2c-designware: use dynamic adapter numbering on Lynxpoint
i2c-designware-pci: use managed functions pcim_* and devm_*
i2c-designware-pci: use dev_err() instead of printk()
i2c-designware: move to managed functions (devm_*)
i2c: remove CONFIG_HOTPLUG ifdefs
i2c: s3c2410: Add SMBus emulation for block read
...
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
Don't print proc_dir_entry data in debug as we're soon to have no direct
access to the contents of the PDE. Print what was put in there instead.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: mjpeg-users@lists.sourceforge.net
cc: linux-media@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull media update from Mauro Carvalho Chehab:
- OF documentation and patches at core and drivers, to be used by for
embedded media systems
- some I2C drivers used on go7007 were rewritten/promoted from staging:
sony-btf-mpx, tw2804, tw9903, tw9906, wis-ov7640, wis-uda1342
- add fimc-is driver (Exynos)
- add a new radio driver: radio-si476x
- add a two new tuners: r820t and tuner_it913x
- split camera code on em28xx driver and add more models
- the cypress firmware load is used outside dvb usb drivers. So, move
it to a common directory to make easier to re-use it
- siano media driver updated to work with sms2270 devices
- several work done in order to promote go7007 and solo6x1x out of
staging (still, there are some pending issues)
- several API compliance fixes at v4l2 drivers that don't behave as
expected
- as usual, lots of driver fixes, improvements, cleanups and new device
addition at the existing drivers.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (831 commits)
[media] cx88: make core less verbose
[media] em28xx: fix oops at em28xx_dvb_bus_ctrl()
[media] s5c73m3: fix indentation of the help section in Kconfig
[media] cx25821-alsa: get rid of a __must_check warning
[media] cx25821-video: declare cx25821_vidioc_s_std as static
[media] cx25821-video: remove maxw from cx25821_vidioc_try_fmt_vid_cap
[media] r820t: Remove a warning for an unused value
[media] dib0090: Fix a warning at dib0090_set_EFUSE
[media] dib8000: fix a warning
[media] dib8000: Fix sub-channel range
[media] dib8000: store dtv_property_cache in a temp var
[media] dib8000: warning fix: declare internal functions as static
[media] r820t: quiet gcc warning on n_ring
[media] r820t: memory leak in release()
[media] r820t: precendence bug in r820t_xtal_check()
[media] videodev2.h: Remove the unused old V4L1 buffer types
[media] anysee: Grammar s/report the/report to/
[media] anysee: Initialize ret = 0 in anysee_frontend_attach()
[media] media: videobuf2: fix the length check for mmap
[media] em28xx: save isoc endpoint number for DVB only if endpoint has alt settings with xMaxPacketSize != 0
...
Along the time, several debug messages were added at cx88-cards.
While those are still useful to track some troubles with
tuners, they're too verbose:
[ 5768.281801] cx88[0]: Calling XC2028/3028 callback
[ 5768.287388] cx88[0]: Calling XC2028/3028 callback
[ 5768.292575] cx88[0]: Calling XC2028/3028 callback
[ 5768.299408] cx88[0]: Calling XC2028/3028 callback
[ 5768.306244] cx88[0]: Calling XC2028/3028 callback
...
and, most of the time, useless.
So, disable them, except if core_debug modprobe parameter
is used.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The hole reason for __must_check is to not ignore an error.
However, a "ret" value is used at cx25821 just to avoid the
Kernel compilation to compain about it.
That, however, produces another warning (with W=1):
drivers/media/pci/cx25821/cx25821-alsa.c: In function 'cx25821_audio_fini':
drivers/media/pci/cx25821/cx25821-alsa.c:727:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
With the current implementation of driver_for_each_device() and
cx25821_alsa_exit_callback(), there's actually just one
very unlikely condition where it will currently produce
an error: if driver_find() returns NULL.
Ok, there's not much that can be done, as it is on a driver's
function that returns void, but it can at least print some message
if the error happens.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes the following warning:
drivers/media/pci/cx25821/cx25821-video.c: At top level:
drivers/media/pci/cx25821/cx25821-video.c:766:5: warning: no previous prototype for 'cx25821_vidioc_s_std' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After cx25821-video cleanup, this var is not used anymore:
drivers/media/pci/cx25821/cx25821-video.c: In function 'cx25821_vidioc_try_fmt_vid_cap':
drivers/media/pci/cx25821/cx25821-video.c:591:15: warning: variable 'maxw' set but not used [-Wunused-but-set-variable]
as the code now checks the max width as the default case for the
range check.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Legacy PCI suspend-resume handlers are called with interrupts enabled.
But cx8800_suspend/cx8800_resume and
cx8802_suspend_common/cx8802_resume_common use spin_lock/spin_unlock
functions to acquire dev->slock, while the same lock is acquired in the
corresponding irq-handlers: cx8800_irq and cx8802_irq.
That means a deadlock is possible if an interrupt happens while suspend
or resume owns the lock. The patch replaces spin_lock/spin_unlock with
spin_lock_irqsave/spin_unlock_irqrestore.
Found by Linux Driver Verification project (linuxtesting.org).
[mchehab@redhat.com: Fix CodingStyle]
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
From Fengguang Wu <fengguang.wu@intel.com>:
> drivers/media/pci/sta2x11/sta2x11_vip.c: In function 'sta2x11_vip_init_one':
> drivers/media/pci/sta2x11/sta2x11_vip.c:1314:2: error: implicit declaration of function 'i2c_get_adapter' [-Werror=implicit-function-declaration]
> drivers/media/pci/sta2x11/sta2x11_vip.c:1314:15: warning: assignment makes pointer from integer without a cast [enabled by default]
> drivers/media/pci/sta2x11/sta2x11_vip.c:1330:2: error: implicit declaration of function 'i2c_put_adapter' [-Werror=implicit-function-declaration]
And also:
> warning: (STA2X11_VIP) selects VIDEO_ADV7180 which has unmet direct dependencies (MEDIA_SUPPORT && VIDEO_V4L2 && I2C)
> drivers/media/i2c/adv7180.c: In function '__adv7180_status':
> drivers/media/i2c/adv7180.c:194:2: error: implicit declaration of function 'i2c_smbus_read_byte_data' [-Werror=implicit-function-declaration]
> drivers/media/i2c/adv7180.c: In function 'adv7180_s_routing':
> drivers/media/i2c/adv7180.c:251:2: error: implicit declaration of function 'i2c_smbus_write_byte_data' [-Werror=implicit-function-declaration]
> drivers/media/i2c/adv7180.c: In function 'adv7180_probe':
> drivers/media/i2c/adv7180.c:551:2: error: implicit declaration of function 'i2c_check_functionality' [-Werror=implicit-function-declaration]
> drivers/media/i2c/adv7180.c:554:2: error: implicit declaration of function 'i2c_adapter_id' [-Werror=implicit-function-declaration]
> drivers/media/i2c/adv7180.c: At top level:
> drivers/media/i2c/adv7180.c:663:1: warning: data definition has no type or storage class [enabled by default]
> drivers/media/i2c/adv7180.c:663:1: warning: type defaults to 'int' in declaration of 'module_i2c_driver' [-Wimplicit-int]
> drivers/media/i2c/adv7180.c:663:1: warning: parameter names (without types) in function declaration [enabled by default]
> drivers/media/i2c/adv7180.c:649:26: warning: 'adv7180_driver' defined but not used [-Wunused-variable]
This is due to the lack of I2C support:
...
> CONFIG_I2C is not set
...
So, Make sure that sta2x11_vip depends on I2C.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't print proc_dir_entry data in debug as we're soon to have no direct
access to the contents of the PDE. Print what was put in there instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The audio output is currently not used as this should be rewritten as an
alsa driver. For the time being remove this source from the Makefile.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ideally this should be implemented with vb2, but it'll do for now.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx25821-video-upstream_ch2.c/h is practically identical to cx25821-video-upstream.c/h
so add support for ch2 into cx25821-video-upstream.c instead.
After this we can replace the custom ioctls with a proper write() interface.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No other changes, just function reordering.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drop the custom ioctls and enable the video output nodes again, this time
using standard ioctls.
The next step will be to provide a proper write() interface.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver does not have subdevices, so why call subdev ops? After
removing that it became apparent that only Composite is supported as
input, so remove also any reference to other inputs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No idea why these custom ioctls exist: they have perfectly normal v4l2
counterparts which are already implemented.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- fill in colorspace
- zero priv
- delete unsupported formats
- fix field handling
- s_std should update width/height
- proper mapping of width/height to valid resolutions
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is now possible to remove cx25821_fh and replace it with v4l2_fh,
which in turn makes event handling and core prio handling possible.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just remember which filehandle is streaming instead of using complicated
resource masks.
After this patch we can replace cx25821_fh with v4l2_fh.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is not a per-filehandle object, it's a per-channel object.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This allows us to replace .ioctl with .unlocked_ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2 core already has support for debugging ioctls/file operations.
No need to do that again.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Embed the video_device struct instead of allocating it.
Remove some of the annoying and ugly kernel messages shown during
loading and unloading of the module.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver doesn't use DVB, RC, cx25840 or tveeprom.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver does not implement cropping, so remove the cropping ioctls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A lot of functions and variables were external when they really can be
declared as static.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The s_input implementation allowed input 1 even if that didn't exist.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This device list is not necessary. The kernel already has all that information,
so just use that instead.
Also remove a bogus refcount and some dead 'private_free' code in the alsa driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
And get rid of the channel0-11 external pointers and two more unused fields
in cx25821.h.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
log_status shouldn't print LOG STATUS lines, the core does that already.
Fix querycap version number and add device_caps support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do some spring cleaning:
- there are no board defines with tuners, so remove bogus tuner support.
- tv standard handling has nothing to do with tuners, so keep that.
- replace the deprecated current_norm by g_std.
- querystd isn't implemented, so remove the ioctl.
- remove a bunch of unused fields in cx25821.h
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This device does not support radio or vbi, so remove anything referring
to that.
In addition, the driver created an 'video ioctl' node, which was unused and
was effectively identical to the first video node.
This bogus video node is now removed, leaving us with 8 video capture nodes
and 2 video output nodes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/cx25821/cx25821-video.c: In function ‘cx25821_video_register’:
drivers/media/pci/cx25821/cx25821-video.c:518:1: warning: the frame size of 1600 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Fixed by just making the struct video_device template static const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Skip the audio channel when registering the video nodes. This fixes a bug
where that incorrectly registered 'video' node was never unregistered.
Note: this bug only surfaces if the video output nodes are enabled again
after the previous patch disabled them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx25821 driver has support for one audio output channel and two video
output channels.
This is implemented in a very ugly and very evil way through a custom ioctl
that passes the filename of a file containing the video data, which is then
read by the driver itself using vfs.
There are a number of problems with this:
1) it's very ugly and very evil (I can't say that often enough).
2) V4L2 supports video output, so why not use that?
3) it's very buggy, closing the filehandle through which you passed the ioctl
will oops the kernel.
4) it's a nasty security leak since this allows you to load any file in the
system as a video or audio source, so in theory you can output /etc/passwd
to audio or video out and record & decode it on another device.
Because of all these issues we no longer register those output video nodes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx25821 driver has support for one audio output channel and two video
output channels.
This is implemented in a very ugly and very evil way through a custom ioctl
that passes the filename of a file containing the video data, which is then
read by the driver itself using vfs.
There are a number of problems with this:
1) it's very ugly and very evil (I can't say that often enough).
2) V4L2 supports video output, so why not use that?
3) it's very buggy, closing the filehandle through which you passed the ioctl
will oops the kernel.
4) it's a nasty security leak since this allows you to load any file in the
system as a video or audio source, so in theory you can output /etc/passwd
to audio or video out and record & decode it on another device.
Because of all these issues we no longer register those output video nodes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make saa7134 driver more V4L2 compliant: clear reserved space of VBI
structure to make sure no garbage is left there
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make saa7134 driver more V4L2 compliant: remove empty g_parm function
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make saa7134 driver more V4L2 compliant: remove empty g_audio and s_audio
functions and don't set audioset in enum_input
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
