Commit graph

104 commits

Author SHA1 Message Date
Peter Ujfalusi
c96907f21f ASoC: TWL4030: PM fix for output amplifiers
Gain controls on outputs affect the power consumption
when the gain is set to non 0 value.

Outputs with amps have one register to configure the
routing and the gain:
PREDL_CTL (0x25):
bit 0: Voice enable
bit 1: Audio L1 enable
bit 2: Audio L2 enable
bit 3: Audio R2 enable
bit 4-5: Gain (0x0 - power down, 0x1 - 6dB, 0x2 - 0dB, 0x3 - -6dB)

bit 0 - 3: is handled in DAPM domain (DAPM_MIXER)
bit 4 - 5: has simple volume control

If there is no audio activity (BIAS_STANDBY), and
user changes the volume, than the output amplifier will
be enabled.
If the user changes the routing (but the codec remains in
BIAS_STANDBY), than the cached gain value also be written
to the register, which enables the amplifier.

The existing workaround for this is to have virtual
PGAs associated with the outputs, and whit DAPM PMD
the gain on the output will be forced to 0 (off) by
bypassing the regcache.
This failed to disable the amplifiers in several
scenario (as mentioned above).

Also if the codec is in BIAS_ON state, and user modifies
a volume control, which path is actually not enabled, than
that amplifier will be enabled as well, but it will
be not turned off, since there is no DAPM path, which
would make mute it.

To prevent amps being enabled, when they are not
needed, introduce the following workaround:
Track the state of each of this type of output.
In twl4030_write only allow actual write, when the
given output is enabled, otherwise only update
the reg_cache.
The PGA event handlers on power up will write the cached
value to the chip (restoring gain, routing selection).
On power down 0 is written to the register (disabling
the amp, and also just in case clearing the routing).

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-22 16:47:12 +00:00
Peter Ujfalusi
e47c796d58 ASoC: TWL4030: Use codec defaults for Headset initial configuration
Disable the amplifiers for the headset outputs, and do not select
routings by default to the headset outputs.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-02-17 14:37:20 +00:00
Peter Ujfalusi
c42a59ea27 ASoC: TWL4030: Add supply for audio serial interface control
The serial interface (TDM/I2S) for the audio block have been
constantly enabled.
Introduce a new DAPM_SUPPLY for handling the AIF_EN bit, so
the interface is only enabled, when there is a need for it.
For example when only the analog loopback is enabled, there
is no need to keep the serial interface active.

I have added the persons who contributed to the Voice path
of twl4030 codec driver, so they might have the ability
to test this patch, and send an update for the Voice path,
if it is necessary

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-02-10 11:14:13 +00:00
Peter Ujfalusi
cb67286d66 ASoC: TWL4030: Module unloading fix
The module unloading path had several problems:
- it freed up the private structure twice
- it freed up the codec structure, which was allocated as part
  of the private structure
- it did not freed up the reg_cache
- it did not unregistered the dais and the codec

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-02-04 10:49:04 +00:00
Peter Ujfalusi
c812459396 ASoC: TWL4030: Modify codec default settings
Change the legacy default register configuration, which left some
internal components on.
Now we have either DAPM, or other ways to control these bits,
so there is no need to enable them by default.

The affected parts:
Disable ADCL and ADCR
Disable ARXL2 and ARXR2 analog PGA (playback)
Disable APLL by default

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-01-28 14:33:10 +00:00
Peter Ujfalusi
fd63df2264 ASoC: TWL4030: Replace comma with semicolon in probe function
The codec structure initialization statements should be
separated by semicolons.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-01-13 13:22:55 +00:00
Balaji T K
fc7b92fca4 mfd: Rename all twl4030_i2c*
This patch renames function names like twl4030_i2c_write_u8,
twl4030_i2c_read_u8 to twl_i2c_write_u8, twl_i2c_read_u8
and also common variable in twl-core.c

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13 21:23:33 +01:00
Santosh Shilimkar
b07682b605 mfd: Rename twl4030* driver files to enable re-use
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.

This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13 20:05:51 +01:00
Mark Brown
0a3f5e35aa ASoC: Remove redundant snd_soc_dapm_new_widgets() calls
The DAPM widgets are now insntantiated by the core when creating the card
so there is no need for the individual CODEC drivers to do so.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-11-12 23:15:08 +00:00
Peter Ujfalusi
68d019553b ASoC: TWL4030: Do not modify the APLL_CTL register
APLL_CTL register is configured by the twl4030-codec MFD
driver.
Remove code, which makes changes in the APLL_CTL register,
and replace those with checks against the configured
audio_mclk configuration done in the MFD driver.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-11-10 12:08:15 +00:00
Mark Brown
fe3e78e073 ASoC: Factor out snd_soc_init_card()
snd_soc_init_card() is always called as the last part of the CODEC probe
function so we can factor it out into the core card setup rather than
have each CODEC replicate the code to do the initialiastation. This will
be required to support multiple CODECs per card.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-11-03 22:14:43 +00:00
Peter Ujfalusi
b3f5a272a3 ASoC: TWL4030: Make sure, that the codec is powered on startup
Set the codec->bias_level to SND_SOC_BIAS_OFF before changing
the initial bias level to STANDBY.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-11-02 17:28:00 +00:00
Peter Ujfalusi
1c3d200271 ASoC: TWL4030: Add APLL supply for the capture path
Capture path also need the APLL enabled, adding DAPM_SUPPLY
for the Virtual ADCs.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-10-29 12:58:22 +00:00
Peter Ujfalusi
7729cf7493 ASoC: TWL4030: Change APLL powering sequence
It seams that certain part of the twl4030 codec needs the APLL
enabled before they are enabled.
Paths which has any digital processing needs need the APLL
enabled before they can function.
For example the vibra output will have some random data after
it is enabled and before the APLL also enabled.

If only analog components are in use (analog bypass), than it
seams, that the APLL does not need to be enabled. This lowers
the power consumption with around ~0.005A.

Adding DAPM_SUPPLY to the Digital playback route and also
to the capture route to enable and disable the APLL.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-10-29 12:58:21 +00:00
Jari Vanhala
86139a13ce ASoC: TWL4030: Vibra motor stop fix when it is driven with audio
This patch fixes vibrator playing incoherently, when driven
with audio. There is something wrong in switch 3 at
H-bridge and VIBRA_SET still affects PWM generator.
Slowest value fixes things.

Signed-off-by: Jari Vanhala <ext-jari.vanhala@nokia.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-10-29 12:58:21 +00:00
Peter Ujfalusi
2845fa13e5 ASoC: TWL4030: Change codec_muted to apll_enabled
codec_muted is missleading, change it to apll_enabled,
which is what it is doing: enabing and disabling the APLL.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-10-28 10:04:21 +00:00
Peter Ujfalusi
78e08e2f20 ASoC: TWL4030: Remove bypass tracking
Since ASoC core now handling the codec bias differently
there is no need to do the tracking of bypass switch states
anymore.

Handling of the common bit for analog loopbacks is done with
DAPM_SUPPLY for the bypass paths.

Now this bit is only enabled when there is a complete analog
bypass path, compared to the previous implementation, when the
global switch was enabled if there were any of the analog
bypass switch was on (regardless if there were complete path or
not)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-10-28 10:04:21 +00:00
Peter Ujfalusi
7a1fecf57f ASoC: TWL4030: Driver registration via twl4030_codec MFD
Change the way how the twl4030 soc codec driver is
loaded/probed.
Use the device probing via tlw4030_codec MFD device.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-10-25 17:15:10 +00:00
Peter Ujfalusi
d8707cecdf ASoC: TWL4030: Only update the needed bits in *set_dai_sysclk
Do not rewrite the whole register, but only update the needed
bits in set_dai_sysclk functions.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-10-19 16:12:17 +01:00
Peter Ujfalusi
9028935d75 ASoC: TWL4030: Fix for capture mixer strings
Change the strings related to capture in order to be
interpreted correctly by alsamixer and possible other
UI based mixer applications.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-14 17:52:59 +01:00
Peter Ujfalusi
9008adf9a9 ASoC: TWL4030: Introduce PGAs for outputs
Dynamically control and control only the needed output amplifier
muting/un-muting.

The original code was muting and un-muting the following output
amplifiers: Earpiece PreDrivL/R, CarkitL/R at the same time
regardless which pin is actually in use at the given moment.

Move these as separate PGA so only the needed amplifier will be touched.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-13 14:56:13 +01:00
Lopez Cruz, Misael
6814044324 ASoC: TWL4030: Add tristate callbacks for HiFi and Voice
Add "set_tristate" callbacks for HiFi and Voice DAIs.
Machine drivers can enable and disable tristate for each
DAI with "snd_soc_dai_set_tristate" function.

Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-07-03 11:01:05 +01:00
Candelaria Villareal, Jorge
4e49ffd10f ASoC: TWL4030: Add EXTMUTE to reduce pop-noise effect
According to TRM, an external FET controlled by a 1.8V output signal
can be used to reduce the pop-noise heard when the audio amplifier is
switched on. It is suggested that GPIO6 of TWL4030 be used, but any
other gpio can be used instead. This is indicated in machine driver
with the following twl4030_setup_data members:

-hs_extmute. Set to 1 if board has support for EXTMUTE.

-set_hs_extmute. Set to a callback funcion to control an external gpio
line. Set to NULL if MUTE[GPIO6] pin is used.

Codec driver takes care of enabling and disabling this output during
the headset pop attenuation sequence.

Also add a delay to let VMID settle in ramp up sequence.

Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-07-02 11:06:26 +01:00
Lopez Cruz, Misael
e3c7dbb07c ASoC: Remove word "Switch" from Handsfree switch name
SoC dapm adds the suffix "Switch" to SND_SOC_DAPM_SWITCH controls,
removing word "Switch" from HandsfreeL/HandsfreeR widget name
for avoiding to duplicate it.

Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-06-26 10:39:52 +01:00
Lopez Cruz, Misael
30808ca751 ASoC: TWL4030: Correct bypass event for voice sidetone
Event for voice sidetone was being interpreted as an
analog HiFi bypass event because VSTPGA register offset
is less than ARXR2_APGA_CTL offset. Reordering the
register checks allows to handle voice digital bypass
event properly.

Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-06-23 10:57:38 +01:00
Lopez Cruz, Misael
328d0a138e ASoC: TWL4030: Add AVADC Clock Priority
AVDAC clk priority allows to determine the path ADC must
be connected when the codec is in option2 and both HiFi
and Voice paths are enabled.

Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-06-23 10:57:37 +01:00
Lopez Cruz, Misael
c264301c77 ASoC: TWL4030: Fix voice interface clock masters
Voice interface of twl4030 codec supports: CBM_CFM and
CBS_CFS. It doesn't support CBS_CFM.

Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-By: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-06-22 11:24:04 +01:00
Mark Brown
423c238d71 ASoC: Staticise put_twl4030_opmode_enum_double()
It's an operation for a control and doesn't need to be exported.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-06-20 13:58:09 +01:00
Mark Brown
b53109db5e ASoC: Fix shadowed variables in twl4030
No need to define second copies of mode and format, they're declared
with exactly the same type at the head of the function and there's no
conflict in their use.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-06-20 13:58:08 +01:00
Takashi Iwai
d08664fdb5 ASoC: Fix build error in twl4030.c
Fix the (likely cut-n-paste) error by commit
16a30fbb0d, which causes the error below:
  sound/soc/codecs/twl4030.c: In function 'twl4030_read_reg_cache':
  sound/soc/codecs/twl4030.c:152: error: 'cache' undeclared (first use in this function)

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-06-04 10:01:11 +02:00
Peter Ujfalusi
eaf1ac8bb5 ASoC: TWL4030: Check the interface format for 4 channel mode
In addition to the operating mode check, also check the
codec's interface format in case of four channel mode.
If the codec is not in TDM (DSP_A) mode, return with error.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-06-01 23:46:08 +01:00
Peter Ujfalusi
16a30fbb0d ASoC: TWL4030: Use reg_cache in twl4030_init_chip
Use the codec->reg_cache instead of the array directly
in twl4030_init_chip for setting the default values.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-05-29 11:02:48 +01:00
Peter Ujfalusi
0f89bdcac6 ASoC: TWL4030: HandsfreeL/R mute DAPM switch
Add DAPM switch for HeadsetL/R mute. Since all bits are are needed
for the HFL/R pop removal to work the switch is using the SW_SHADOW
no HW register for the HandsfreeL/R mute.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-05-25 11:54:14 +01:00
Peter Ujfalusi
f3b5d3002d ASoC: TWL4030: Add shadow register
Shadow, non HW register for dealing with the HandsfreeL/R
muting.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-05-25 11:54:14 +01:00
Peter Ujfalusi
5a2e9a48b1 ASoC: TWL4030: Handsfree pop removal redesign
Move the HandsfreeL/R (IHFL/R) pop removal code from the DAPM_MUX_E
to a more appropriate DAPM_PGA_E widget.
Also fix the power-up sequence to match with the TRM.
The power-down sequence is not described in the TRM, so do it
in a way, which seams like the correct sequence.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-05-25 11:54:13 +01:00
Peter Ujfalusi
b4852b793a ASoC: TWL4030: Differentiate the playback streams
Give unique stream names for the two playback streams so
DAPM can figure out which codec_dai is in use.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-05-22 15:08:43 +01:00
Peter Ujfalusi
9da28c7b38 ASoC: TWL4030: Add support for platform dependent configuration
twl4030_setup_data structure can be passed from platform drivers to
the codec via the snd_soc_device->codec_data pointer.

Currently the setup data has support for the Headset pop-removal
related configuration, which differs from board to board.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-05-22 10:23:22 +01:00
Peter Ujfalusi
6943c92e87 ASoC: TWL4030: Move the Headset pop-attenuation code to PGA event
This patch adds SND_SOC_DAPM_PGA_E to the headset path, which handles
the headset ramp up and down sequences needed for the pop noise
removal.

With this patch the order of the internal components in the twl4030
codec is turned on and off in a correct order.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Tested-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Tested-by: Misael Lopez Cruz  <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-05-20 09:53:25 +01:00
Peter Ujfalusi
4005d39a5f ASoC: TWL4030: Change DAPM routings and controls for DACs and PGAs
Restructuring the twl4030 codec's DAPM routing to be able to handle the power
sequences correctly.

The twl4030 codec internal implementation have this order:
DAC -> Analog PGA -> Mixer/Mux

While the ASoC framework expects the following order:
DAC -> Mixer -> Analog PGA

This patch moves the Analog PGA handling from SND_SOC_DAPM_PGA to _MIXER and
adds two levels of mixer to handle the digital and analog loopback
functionality.

Now the analog loopback does not powers on any of the DACs.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Tested-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Tested-by: Misael Lopez Cruz  <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-05-20 09:52:51 +01:00
Lopez Cruz, Misael
b74bd40fa4 ASoC: TWL4030: Add control for selecting codec operation mode
Add a control for selecting the codec operation mode. TWL4030 codec
has two modes:
- Option 1. Audio only (4 audio DACs)
- Option 2. Voice/Audio (2 audio DACs and voice ADC/DAC)

Control is restricted when a stream is ongoing, since codec's
operation mode cannot be changed on-the-fly.

Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujflausi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-05-19 10:35:11 +01:00
Peter Ujfalusi
181da78cd0 ASoC: TWL4030: Fix Analog capture path for AUXR
AUXR is selected by bit 2 and not by bit 1 in the ANAMICR register.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-05-19 09:38:57 +01:00
Misael Lopez Cruz
b7a755a8a1 ASoC: TWL4030: Enable/disable voice digital filters
Enable TWL4030 VTXL/VTXR and VRX digital filters for uplink
and downlink paths, respectively.

This patch also corrects voice 8/16kHz mode selection bit
(SEL_16K) of CODEC_MODE register.

Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-05-18 11:13:12 +01:00
Joonyoung Shim
97b8096dc9 ASoC: TWL4030: change DAPM for analog microphone selection
The inputs of the twl4030 codec can be mixed, so we will use the mixer
DAPM for the analog microphone registers(0x05, 0x06), but if we enable
more than one input at the same time, the input impedance of the input
amplifier will be reduced.

Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-05-12 10:53:22 +01:00
Peter Ujfalusi
c198d81181 ASoC: TWL4030: Fix typo in twl4030_codec_mute function
Copy-paste error: TWL4030_PRECKL_GAIN >> TWL4030_PRECKR_GAIN
It has not caused problems, since
TWL4030_PRECKL_GAIN == TWL4030_PRECKR_GAIN == 0x30

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-05-08 12:00:12 +01:00
Peter Ujfalusi
376f7839b7 ASoC: TWL4030: Add VIBRA output
This patch adds support for the VIBRA output on TWL4030 codec.
The VIBRA output can be driven with audio data or with
local vibrator driver.
Add the needed DAPM elements and routes for the VIBRA output and
controls for the VIBRA driver configuration.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-05-05 10:12:45 +01:00
Lopez Cruz, Misael
ee8f6894f3 ASoC: TWL4030: Add voice digital loopback: sidetone
This patch add voice digital loopback (sidetone) to the twl4030
driver. It mixes voice uplink attenuated (by sidetone gain) with
voice downlink when the codec is working in option2 (voice/audio
mode).

Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-05-05 10:12:20 +01:00
Lopez Cruz, Misael
fcd274a345 ASoC: TWL4030: Add VDL analog bypass
This patch adds voice downlink analog bypass switch. It follows
the same approach as in other analog bypass switches.
DAC switch is moved from 'DAC Voice' to 'Analog Voice Playback Mixer',
that will also allow voice DAC to be powered in digital voice
loopback (sidetone).

Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-05-05 10:12:14 +01:00
Mark Brown
72e31981a4 Merge branch 'for-2.6.30' into for-2.6.31 2009-04-28 19:33:45 +01:00
Joonyoung Shim
18cc8d8d9b ASoC: TWL4030: Fix gain control for earpiece amplifier
The gain control for earpiece amplifier uses 0dB ~ 12dB according to the
TRM, but the present code is implemented to -6dB ~ 6dB.

Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-04-28 16:11:22 +01:00
Peter Ujfalusi
8a1f936acd ASoC: TWL4030: Add 4 channel TDM support
Support for 4 channel TDM (SND_SOC_DAIFMT_DSP_A) for twl4030
codec.
The channel allocations are:
Playback:
TDM         i2s   TWL RX
Channel 1   Left  SDRL2
Channel 3   Right SDRR2
Channel 2   --    SDRL1
Channel 4   --    SDRR1

Capture:
TDM         i2s   TWL TX
Channel 1   Left  TXL1
Channel 3   Right TXR1
Channel 2   --    TXL2
Channel 4   --    TXR2

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-04-23 16:11:17 +01:00