This patch is primarily a port of the integrated IR controller code in
cx23885/cx23888-ir.c. Right now, only the CX2388[57] AV core will
really try to set up IR. This IR support, by design, still requires the
bridge driver to do final IO pin mux configuration and setup of the IR
controller parameters.
For the CX2388[578] chips, enabling the AV Core for IR also starts
sending Audio and Video interrupts to the bridge driver. For
CX2388[578] chips audio and video interrupts are ignored and
acknowledged when they happen.
IR interrupt handling and status logging is exluded for the CX23888
which does not have an IR controller on the AV core.
Note that experimentation reveals that the IR irq enables on the
CX23885 have an inverted logic sense. The CX23887 likely suffers from
the same quirk. For these chips, those irq enable bits are handled
as interrupt disables.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CX2584x and related cores are multifunction subdevices with a number
of internal blocks that act as interrupt sources. Move the v4L2_subdev
interrupt_service_routine callback from v4l_subdev_ir_ops to
v4l2_subdev_core_ops, as the video and audio blocks of a CX2584x and
related cores can generate interrupts along with the IR block. This
change also makes sense for other subdev's that generate interrupts and
do not have an IR block.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Explicitly configure the IR Tx and IR Rx pins to be driven by the
IR Rx and Tx pads from the AV core for CX23888 IR.
For the HVR-1850 and HVR-1290 configure the IR Tx level inversion,
so the Tx LED is off when idle.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a distinction on IR Tx for the CX2388[578] chips of carrier
sense inversion (space is a carrier burst and mark is no burst) and I/O
pin level inversion (0 is high output level, 1 is low output level).
Allow the caller to set these parameters distinctly as v4l2_subdevice
IR parameters. This permits the IR device to be configured and enabled
without the IR Tx LED being on during idle/space time due to an external
hardware level inversion
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add s_io_pin_config core subdev op for the CX2388[578] AV cores.
This is complete for IR_RX, IR_TX, GPIOs 16,19-23, and IRQ_N.
It likely needs work for the I2S signal direction.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a simple log_status function for raw analog video capture device nodes,
to provide insight into the state of the CX2388[578] A/V decoder core.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The offset in the eeprom data for the 79501 version of the HVR-1250 is at 0xc0
vs. the standard 0x80.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was a small window between writing the cx25840 register
address over the i2c bus and reading the register contents back from the
cx25840 device that the i2c adapter lock was released. This change ensures the
adapter lock is not released until the register read is done.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Function i2c_wait_done() never returns negative values, so there is no
point in checking for them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't just check for nacks on zero-length transactions. Check on
other transactions too.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Documentation/i2c/fault-codes says that i2c adapter drivers should
return -ENXIO when no slave acks an address byte.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On laptops, the webcam sometimes disconnects when writing the first main
register (b300). This patch prevents the creation of a new /dev/video<n>
on streaming start.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The added controls are exposure, gain, autogain and backlight compensation.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The JPEG format did not work fine. The Bayer format offers correct VGA (640x480)
resolution, but bad QQVGA (160x120). This last resolution is removed.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bit 7 of the sensor gain register multiplies the 7bits value by two.
It is now always set with half the user gain value.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The start_1 exchange must be done by (reg, val) * 5 and not 8.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sensor enum definition was not at the right place.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (82 commits)
firewire: core: add forgotten dummy driver methods, remove unused ones
firewire: add isochronous multichannel reception
firewire: core: small clarifications in core-cdev
firewire: core: remove unused code
firewire: ohci: release channel in error path
firewire: ohci: use memory barriers to order descriptor updates
tools/firewire: nosy-dump: increment program version
tools/firewire: nosy-dump: remove unused code
tools/firewire: nosy-dump: use linux/firewire-constants.h
tools/firewire: nosy-dump: break up a deeply nested function
tools/firewire: nosy-dump: make some symbols static or const
tools/firewire: nosy-dump: change to kernel coding style
tools/firewire: nosy-dump: work around segfault in decode_fcp
tools/firewire: nosy-dump: fix it on x86-64
tools/firewire: add userspace front-end of nosy
firewire: nosy: note ioctls in ioctl-number.txt
firewire: nosy: use generic printk macros
firewire: nosy: endianess fixes and annotations
firewire: nosy: annotate __user pointers and __iomem pointers
firewire: nosy: fix device shutdown with active client
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (55 commits)
workqueue: mark init_workqueues() as early_initcall()
workqueue: explain for_each_*cwq_cpu() iterators
fscache: fix build on !CONFIG_SYSCTL
slow-work: kill it
gfs2: use workqueue instead of slow-work
drm: use workqueue instead of slow-work
cifs: use workqueue instead of slow-work
fscache: drop references to slow-work
fscache: convert operation to use workqueue instead of slow-work
fscache: convert object to use workqueue instead of slow-work
workqueue: fix how cpu number is stored in work->data
workqueue: fix mayday_mask handling on UP
workqueue: fix build problem on !CONFIG_SMP
workqueue: fix locking in retry path of maybe_create_worker()
async: use workqueue for worker pool
workqueue: remove WQ_SINGLE_CPU and use WQ_UNBOUND instead
workqueue: implement unbound workqueue
workqueue: prepare for WQ_UNBOUND implementation
libata: take advantage of cmwq and remove concurrency limitations
workqueue: fix worker management invocation without pending works
...
Fixed up conflicts in fs/cifs/* as per Tejun. Other trivial conflicts in
include/linux/workqueue.h, kernel/trace/Kconfig and kernel/workqueue.c
* 'v4l_for_2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (243 commits)
V4L/DVB: sms: Convert IR support to use the Remote Controller core
V4L/DVB: sms: properly initialize IR phys and IR name
V4L/DVB: standardize names at rc-dib0700 tables
V4L/DVB: smsusb: enable IR port for Hauppauge WinTV MiniStick
V4L/DVB: dib0700: Fix RC protocol logic to properly handle NEC/NECx and RC-5
V4L/DVB: dib0700: properly implement IR change_protocol
V4L/DVB: dib0700: break keytable into NEC and RC-5 variants
V4L/DVB: dib0700: avoid bad repeat
V4L/DVB: Port dib0700 to rc-core
V4L/DVB: Add a keymap file with dib0700 table
V4L/DVB: dvb-usb: add support for rc-core mode
V4L/DVB: dvb-usb: prepare drivers for using rc-core
V4L/DVB: dvb-usb: get rid of struct dvb_usb_rc_key
V4L/DVB: rj54n1cb0c: fix a comment in the driver
V4L/DVB: V4L2: sh_vou: VOU does support the full PAL resolution too
V4L/DVB: V4L2: sh_mobile_camera_ceu: add support for CSI2
V4L/DVB: V4L2: soc-camera: add a MIPI CSI-2 driver for SH-Mobile platforms
V4L/DVB: V4L2: soc-camera: export soc-camera bus type for notifications
V4L/DVB: V4L2: mediabus: add 12-bit Bayer and YUV420 pixel formats
V4L/DVB: mediabus: fix ambiguous pixel code names
...
Rewrites the siano IR implementation. The previous implementation were
non-standard. As such, it has issues if more than one device registers IR,
as there used to have some static constants used during protocol decoding
phase. Also, it used to implement its on RAW decoder, and only for RC5.
The new code uses RC core subsystem for handling IR. This brings several
new features to the driver, including:
- Allow to dynamically replace the IR keycodes;
- Supports all existing raw decoders (JVC, NEC, RC-5, RC-6, SONY);
- Supports lirc dev;
- Doesn't have race conditions when more than one sms IR is
registered;
- The code size for the IR implementation is very small;
- it exports the IR features via /sys/class/rc.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use a more standard way to name those tables, as they're currently used
by the script that coverts those tables to be loaded via userspace.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the proper gpio port for WinTV MiniStick, with the information provided
by Michael.
Thanks-to: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Simplifies the logic for handling firmware 1.20 RC messages, fixing the
logic.
While here, I tried to use a RC-6 remote controller from my TV set, but it
didn't work with dib0700. Not sure why, but maybe this never worked.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch implements change_protocol callback. With this change,
there's no need for an extra modprobe parameter to specify the
protocol. When a table is loaded (either from in-kernel rc-map
tables or via ir-keytable program), the driver will automatically
change the protocol, in order to work with the given table.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having one big keytable with 2 protocols inside, break it
into two separate tables, being one for NEC and another for RC-5 variants,
and properly identify what variant should be used at the boards entries.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
a 250ms delay is too low for this device. It ends by producing false
repeat events. Increase the delay time to 500 ms to avoid troubles.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allows dvb-usb drivers to use rc-core, instead of the legacy
implementation.
No driver were ported yet to rc-core, so, some small adjustments
may be needed, when starting to migrate the drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a big patch, yet trivial. It just move the RC properties
to a separate struct, in order to prepare the dvb-usb drivers to
use rc-core. There's no change on the behavior of the drivers.
With this change, it is possible to have both legacy and rc-core
based code inside the dvb-usb-remote, allowing a gradual migration
to rc-core, driver per driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dvb-usb has its own IR handle code. Now that we have a Remote
Controller subsystem, we should start using it. So, remove this
struct, in favor of the similar struct defined at the RC subsystem.
This is a big, but trivial patch. It is a 3 line delect, plus
lots of rename on several dvb-usb files.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
RJ54N1CB0C is a Sharp camera sensor.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SH7724 datasheet specifies 480 pixels as the VOU maximum vertical resolution.
This is a bug in the datasheet, VOU also supports the full PAL resolution: 576
lines. Adjust the driver accordingly.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using CEU with CSI2 on SH-Mobile requires some special configuration of the
former. We also have to switch from calling only one subdev .s_mbus_fmt and
.try_mbus_fmt to calling all subdevices. Take care to increment CSI2 driver
use count to prevent it from unloading, while in use.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some SH-Mobile SoCs implement a MIPI CSI-2 controller, that can interface to
several video clients and send data to the CEU or to the Image Signal
Processor. This patch implements a v4l2-subdevice driver for CSI-2 to be used
within the soc-camera framework, implementing the second subdevice in addition
to the actual video clients.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Endianness notation is meaningless for 8 bit YUYV codes. Switch pixel code
names to explicitly state the order of colour components in the data
stream.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds support for the KWorld PlusTV 340U and KWorld UB345-Q ATSC
sticks, which are really the same device. The sticks have an eMPIA
em2870 usb bridge chipset, an LG Electronics LGDT3304 ATSC/QAM
demodulator and an NXP TDA18271HD tuner -- early versions of the 340U
have a a TDA18271HD/C1, later models and the UB435-Q have a C2.
The stick has been tested succesfully with both VSB_8 and QAM_256 signals.
Its using lgdt3304 support added to the lgdt3305 driver by a prior patch,
rather than the current lgdt3304 driver, as its severely lacking in
functionality by comparison (see said patch for details).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In dvb_dvr_release, there is a test dvbdev->users==-1, but users are
never negative. This error results in hung tasks:
task PC stack pid father
bash D ffffffffa000c948 0 3264 3170 0x00000000
ffff88003aec5ce8 0000000000000086 0000000000011f80 0000000000011f80
ffff88003aec5fd8 ffff88003aec5fd8 ffff88003b848670 0000000000011f80
ffff88003aec5fd8 0000000000011f80 ffff88003e02a030 ffff88003b848670
Call Trace:
[<ffffffff813dd4a5>] dvb_dmxdev_release+0xc5/0x130
[<ffffffff8107b750>] ? autoremove_wake_function+0x0/0x40
[<ffffffffa00013a2>] dvb_usb_adapter_dvb_exit+0x42/0x70 [dvb_usb]
[<ffffffffa0000525>] dvb_usb_exit+0x55/0xd0 [dvb_usb]
[<ffffffffa00005ee>] dvb_usb_device_exit+0x4e/0x70 [dvb_usb]
[<ffffffffa000a065>] af9015_usb_device_exit+0x55/0x60 [dvb_usb_af9015]
[<ffffffff813a3f05>] usb_unbind_interface+0x55/0x1a0
[<ffffffff81316000>] __device_release_driver+0x70/0xe0
...
So check against 1 there instead.
BTW why's the TODO there? Adding TODOs to the code without
descriptions is like adding nothing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The UVC host and gadget drivers both define constants and structures in
private header files. Move all those definitions to linux/usb/video.h
where they can be shared by the two drivers (and be available for
userspace applications).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
