__test_and_clear_bit() returns a bitfield with the tested-for bit set.
Make it consistent with the other bitops - of ia64 but also every
other architecture - and return a boolean value.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
In commit 160c1d8e40,
dma_ops->dma_supported = iommu_dma_supported;
This dma_ops->dma_supported is first called in platform_dma_init() during kernel
boot. Then dma_ops->dma_supported will be called recursively in
iommu_dma_supported.
Kernel can not boot because kernel can not get out of iommu_dma_supported until
it runs out of stack memory.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
2.6.31-rc kernels don't boot on my ixp4xx box (ds101), because the libata
driver doesn't find the PCI IDE controller any more. 2.6.30 was fine.
I traced this to a PCI update (1f82de10d6)
in 2.6.30-git19. Diffing the kernel boot logs from 2.6.30-git18 and
2.6.30-git19 illustrates the breakage:
> --- dmesg-2.6.30-git18 2009-08-04 01:45:22.000000000 +0200
> +++ dmesg-2.6.30-git19 2009-08-04 01:45:46.000000000 +0200
> @@ -26,6 +26,13 @@
> pci 0000:00:02.2: PME# supported from D0 D1 D2 D3hot
> pci 0000:00:02.2: PME# disabled
> PCI: bus0: Fast back to back transfers disabled
> +pci 0000:00:01.0: BAR 0: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 1: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 2: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 3: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 4: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:02.0: BAR 4: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:02.1: BAR 4: can't allocate I/O resource [0x10000-0xffff]
> bio: create slab <bio-0> at 0
> SCSI subsystem initialized
> NET: Registered protocol family 2
> @@ -44,11 +51,7 @@
> console [ttyS0] enabled
> serial8250.0: ttyS1 at MMIO 0xc8001000 (irq = 13) is a XScale
> Driver 'sd' needs updating - please use bus_type methods
> -PCI: enabling device 0000:00:01.0 (0140 -> 0141)
> -scsi0 : pata_artop
> -scsi1 : pata_artop
> -ata1: PATA max UDMA/100 cmd 0x1050 ctl 0x1060 bmdma 0x1040 irq 28
> -ata2: PATA max UDMA/100 cmd 0x1058 ctl 0x1064 bmdma 0x1048 irq 28
> +pata_artop 0000:00:01.0: no available native port
> Using configured DiskOnChip probe address 0x50000000
> DiskOnChip found at 0x50000000
> NAND device: Manufacturer ID: 0x98, Chip ID: 0x73 (Toshiba NAND 16MiB 3,3V 8-bit)
The specific change in 1f82de10d6 responsible
for this failure turned out to be the following:
> --- a/drivers/pci/probe.c
> +++ b/drivers/pci/probe.c
> @@ -193,7 +193,7 @@ int __pci_read_base(struct pci_dev *dev, enum pci_bar_type type,
> res->flags |= pci_calc_resource_flags(l) | IORESOURCE_SIZEALIGN;
> if (type == pci_bar_io) {
> l &= PCI_BASE_ADDRESS_IO_MASK;
> - mask = PCI_BASE_ADDRESS_IO_MASK & 0xffff;
> + mask = PCI_BASE_ADDRESS_IO_MASK & IO_SPACE_LIMIT;
> } else {
> l &= PCI_BASE_ADDRESS_MEM_MASK;
> mask = (u32)PCI_BASE_ADDRESS_MEM_MASK;
Every arch except arm's ixp4xx defines IO_SPACE_LIMIT as an all-bits-one
bitmask, typically -1UL but sometimes only a 16-bit 0x0000ffff. But ixp4xx
defines it as 0xffff0000, which is now causing the PCI failures.
Russell King noted that ixp4xx has 64KB PCI IO space, so IO_SPACE_LIMIT
should be 0x0000ffff. This patch makes that change, which fixes the PCI
failures on my ixp4xx box.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Due to an erratum with certain AMD Athlon 64 processors, the
BIOS may need to force enable the LAHF_LM capability.
Unfortunately, in at least one case, the BIOS does this even
for processors that do not support the functionality.
Add a specific check that will clear the feature bit for
processors known not to support the LAHF/SAHF instructions.
Signed-off-by: Kevin Winchester <kjwinchester@gmail.com>
Acked-by: Borislav Petkov <petkovbb@googlemail.com>
LKML-Reference: <4A80A5AD.2000209@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Johannes Stezenbach reported that 'perf stat' does not count
cache-miss and cache-references events on his Pentium-M based
laptop.
This is because we left them blank in p6_perfmon_event_map[],
fill them in.
Reported-by: Johannes Stezenbach <js@sig21.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
My Latitude d630 seems to be handling thermal events in SMI by
lowering the max frequency of the CPU till it cools down but
still leaks the "everything is normal" events.
This spams the console and with high priority printks.
Adjust therm_throt driver to only print messages about the fact
that temperatire returned back to normal when leaving the
throttling state.
Also lower the severity of "back to normal" message from
KERN_CRIT to KERN_INFO.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <20090810051513.0558F526EC9@mailhub.coreip.homeip.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
ALC269 and ALC861-VD parsers override the ADC definitions
unconditionally without checking the spec definition. This causes
the problem when any inconsistent ADC is set up in the device quirk
(like ALC272 with digital-mic).
This patch avoids the overriding by adding the proper checks.
Reference: Novell bnc#529467
https://bugzilla.novell.com/show_bug.cgi?id=529467
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix memory leakage in /security/selinux/hooks.c
The buffer always needs to be freed here; we either error
out or allocate more memory.
Reported-by: iceberg <strakh@ispras.ru>
Signed-off-by: James Morris <jmorris@namei.org>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Commit 783ea7d4ee
(Driver Core: Rework platform suspend/resume, print warning)
added a warning message printed for platform drivers that use the
legacy PM callbacks rather than struct dev_pm_ops. Unfortunately,
this resulted in some confusion and made some people try to convert
drivers by replacing the old callbacks with struct dev_pm_ops in
automatic way, which generally is not a good idea.
Remove the platform device runtime dev_pm_ops warning for now,
because it's annoying to users and it's not really necessary right
now.
[rjw: Modified the changelog to be more informative.]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
queue == __AR9170_NUM_TXQ would cause a bug on the next line.
found by Smatch ( http://repo.or.cz/w/smatch.git ).
Cc: stable@kernel.org
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ar9170-2.fw was missing, the driver erroneously complained
about missing the initialization values file ar9170-1.fw...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit d945cb9cc ("pty: Rework the pty layer to use the normal buffering
logic") dropped the test for 'tty->stopped' in pty_write_room(), which
then causes the n_tty line discipline thing to not throttle the data
properly when the tty is stopped.
So instead of pausing the write due to the tty being stopped, the ldisc
layer would go ahead and push it down to the pty. The pty write()
routine would then refuse to take the data (because it _did_ check
'stopped'), and the data wouldn't actually be written.
This whole stopped test should eventually be moved into the tty ldisc
layer rather than have low-level tty drivers care about these things,
but right now the fix is to just re-instate the missing pty 'stopped'
handling.
Reported-and-tested-by: Artur Skawina <art.08.09@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In OCFS2, allocator locks rank above transaction start. Thus we
cannot extend quota file from inside a transaction less we could
deadlock.
We solve the problem by starting transaction not already in
ocfs2_acquire_dquot() but only in ocfs2_local_read_dquot() and
ocfs2_global_read_dquot() and we allocate blocks to quota files before starting
the transaction. In case we crash, quota files will just have a few blocks
more but that's no problem since we just use them next time we extend the
quota file.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Reboot does not work on my MacBook Pro 13 inch (MacBookPro5,5)
too. It seems all unibody MacBook and MacBookPro require
PCI reboot handling, i guess.
Following model/machine ID list shows unibody MacBook/Pro have
the 5 series of model number:
http://www.everymac.com/systems/by_capability/macs-by-machine-model-machine-id.html
Signed-off-by: Shunichi Fuji <palglowr@gmail.com>
Cc: Ozan Çağlayan <ozan@pardus.org.tr>
LKML-Reference: <30046e3b0908101134p6487ddbftd8776e4ddef204be@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
perf_counter: Zero dead bytes from ftrace raw samples size alignment
perf_counter: Subtract the buffer size field from the event record size
perf_counter: Require CAP_SYS_ADMIN for raw tracepoint data
perf_counter: Correct PERF_SAMPLE_RAW output
perf tools: callchain: Fix bad rounding of minimum rate
perf_counter tools: Fix libbfd detection for systems with libz dependency
perf: "Longum est iter per praecepta, breve et efficax per exempla"
perf_counter: Fix a race on perf_counter_ctx
perf_counter: Fix tracepoint sampling to be part of generic sampling
perf_counter: Work around gcc warning by initializing tracepoint record unconditionally
perf tools: callchain: Fix sum of percentages to be 100% by displaying amount of ignored chains in fractal mode
perf tools: callchain: Fix 'perf report' display to be callchain by default
perf tools: callchain: Fix spurious 'perf report' warnings: ignore empty callchains
perf record: Fix the -A UI for empty or non-existent perf.data
perf util: Fix do_read() to fail on EOF instead of busy-looping
perf list: Fix the output to not include tracepoints without an id
perf_counter/powerpc: Fix oops on cpus without perf_counter hardware support
perf stat: Fix tool option consistency: rename -S/--scale to -c/--scale
perf report: Add debug help for the finding of symbol bugs - show the symtab origin (DSO, build-id, kernel, etc)
perf report: Fix per task mult-counter stat reporting
...
If futex_requeue(requeue_pi=1) finds a futex_q that was created by a call
other the futex_wait_requeue_pi(), the q.rt_waiter may be null. If so,
this will result in an oops from the following call graph:
futex_requeue()
rt_mutex_start_proxy_lock()
task_blocks_on_rt_mutex()
waiter->task dereference
OOPS
We currently WARN_ON() if this is detected, clearly this is inadequate.
If we detect a mispairing in futex_requeue(), bail out, seding -EINVAL to
user-space.
V2: Fix parenthesis warnings.
Signed-off-by: Darren Hart <dvhltc@us.ibm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: John Kacur <jkacur@redhat.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Dinakar Guniguntala <dino@in.ibm.com>
Cc: John Stultz <johnstul@linux.vnet.ibm.com>
LKML-Reference: <4A7CA8C0.7010809@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI hotplug: SGI hotplug: do not use hotplug_slot_attr
PCI hotplug: SGI hotplug: fix build failure
Wei Chong Tan reported a fast-PIT-calibration corner-case:
| pit_expect_msb() is vulnerable to SMI disturbance corner case
| in some platforms which causes /proc/cpuinfo to show wrong
| CPU MHz value when quick_pit_calibrate() jumps to success
| section.
I think that the real issue isn't even an SMI - but the fact
that in the very last iteration of the loop, there's no
serializing instruction _after_ the last 'rdtsc'. So even in
the absense of SMI's, we do have a situation where the cycle
counter was read without proper serialization.
The last check should be done outside the outer loop, since
_inside_ the outer loop, we'll be testing that the PIT has
the right MSB value has the right value in the next iteration.
So only the _last_ iteration is special, because that's the one
that will not check the PIT MSB value any more, and because the
final 'get_cycles()' isn't serialized.
In other words:
- I'd like to move the PIT MSB check to after the last
iteration, rather than in every iteration
- I think we should comment on the fact that it's also a
serializing instruction and so 'fences in' the TSC read.
Here's a suggested replacement.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: "Tan, Wei Chong" <wei.chong.tan@intel.com>
Tested-by: "Tan, Wei Chong" <wei.chong.tan@intel.com>
LKML-Reference: <B28277FD4E0F9247A3D55704C440A140D5D683F3@pgsmsx504.gar.corp.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
mm_for_maps: take ->cred_guard_mutex to fix the race with exec
mm_for_maps: shift down_read(mmap_sem) to the caller
mm_for_maps: simplify, use ptrace_may_access()
Fix the following 'make includecheck' warning:
arch/mn10300/include/asm/pci.h: linux/mm.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
clean up type-casting twice. "size_t" is typedef as "unsigned long" in
64-bit system, and "unsigned int" in 32-bit system, and the intermediate
cast to 'long' is pointless.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This will register the ioctl range used by nilfs2 file system to the
table listed in Documentation/ioctl/ioctl-number.txt.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We compute the perf raw sample size by aligning the raw ftrace
event size plus the buffer size field itself. We do that
instead of aligning only the perf raw sample size, so that we
might economize some in some cases.
But this buffer size field is not stored in the perf raw
sample, we must then substract its size from the buffer once we
computed the alignment unless we may get a useless u32 field in
the buffer.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20090810141129.GA5124@nowhere>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Need to add the REQUEUE_PI checks to the compat_sys_futex API
as well to ensure 32 bit requeue's work fine on a 64 bit
system. Patch is against latest tip
Signed-off-by: Dinakar Guniguntala <dino@in.ibm.com>
Cc: Darren Hart <dvhltc@us.ibm.com>
LKML-Reference: <20090810130142.GA23619@in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Give waitqueue spinlocks their own lockdep classes when they
are initialised from init_waitqueue_head(). This means that
struct wait_queue::func functions can operate other waitqueues.
This is used by CacheFiles to catch the page from a backing fs
being unlocked and to wake up another thread to take a copy of
it.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Cc: linux-cachefs@redhat.com
Cc: torvalds@osdl.org
Cc: akpm@linux-foundation.org
LKML-Reference: <20090810113305.17284.81508.stgit@warthog.procyon.org.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Added REGULATOR, MMC and updated default CMDLINE so RX51 now boots.
Note that the regulator code should be moved from mmc-twl4030.c
to omap_hsmmc.c so it can be a module.
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
twl_mmc_cleanup() must free up the regulators that were
allocated by twl_mmc_late_init().
This eliminates the below error when 'omap_hsmmc' module is
repeatedly loaded and unloaded.
"sysfs: cannot create duplicate filename '/devices/platform
/mmci-omap-hs.0/microamps_requested_vmmc'"
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OTG transceiver to RX51 platform data to prevent kernel NULL pointer
dereference during MUSB initialisation.
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes a wrong setting of resource parameter list in
SMSC911x platform driver data structure for Overo case.
This fixes folowing warning when compiling for Overo board:
warning: initialization from incompatible pointer type
Introduced since commit id:
commit 172ef27544
Author: Steve Sakoman <sakoman@gmail.com>
Date: Mon Feb 2 06:27:49 2009 +0000
ARM: Add SMSC911X support to Overo platform (V2)
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit e85c205ac1 increase vmalloc size.
vmalloc space will overlap with OMAP3 sram virtual address.
Signed-off-by: Li Hong Mei <hong-mei.li@motorola.com>
Signed-off-by: Janboe Ye <yuan-bo.ye@motorola.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
This errata is valid for:
OMAP2420 Errata 1.85 Impacts all 2420 ES rev
OMAP2430 Errata 1.10 Impacts only ES1.0
Description: DMA may hang when several channels are used in parallel
OMAP3430: Not impacted, so remove the errata fix for omap3
Fixed issue reported on cpu_is_omap24xx check reported by Nishant Kamat
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Reviewed-by: Nishant Kamat <nskamat@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to keep these defines limited in the ifdef block
for mach-omap2. It will just cause problems testing for the CPU
revision in the common code, like the next patch does for the DMA
errata.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The problem is minor, but without ->cred_guard_mutex held we can race
with exec() and get the new ->mm but check old creds.
Now we do not need to re-check task->mm after ptrace_may_access(), it
can't be changed to the new mm under us.
Strictly speaking, this also fixes another very minor problem. Unless
security check fails or the task exits mm_for_maps() should never
return NULL, the caller should get either old or new ->mm.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
mm_for_maps() takes ->mmap_sem after security checks, this looks
strange and obfuscates the locking rules. Move this lock to its
single caller, m_start().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
It would be nice to kill __ptrace_may_access(). It requires task_lock(),
but this lock is only needed to read mm->flags in the middle.
Convert mm_for_maps() to use ptrace_may_access(), this also simplifies
the code a little bit.
Also, we do not need to take ->mmap_sem in advance. In fact I think
mm_for_maps() should not play with ->mmap_sem at all, the caller should
take this lock.
With or without this patch, without ->cred_guard_mutex held we can race
with exec() and get the new ->mm but check old creds.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Without the initialization of vmaster NID, the dB information got
confused for ALC269 codec.
Reference: Novell bnc#527361
https://bugzilla.novell.com/show_bug.cgi?id=527361
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
Raw tracepoint data contains various kernel internals and
data from other users, so restrict this to CAP_SYS_ADMIN.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1249896452.17467.75.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
PERF_SAMPLE_* output switches should unconditionally output the
correct format, as they are the only way to unambiguously parse
the PERF_EVENT_SAMPLE data.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1249896447.17467.74.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
futex_requeue() can acquire the lock on behalf of a waiter
early on or during the requeue loop if it is uncontended or in
the event of a lock steal or owner died. On wakeup, the waiter
(in futex_wait_requeue_pi()) cleans up the pi_state owner using
the lock_ptr to protect against concurrent access to the
pi_state. The pi_state is hung off futex_q's on the requeue
target futex hash bucket so the lock_ptr needs to be updated
accordingly.
The problem manifested by triggering the WARN_ON in
lookup_pi_state() about the pid != pi_state->owner->pid. With
this patch, the pi_state is properly guarded against concurrent
access via the requeue target hb lock.
The astute reviewer may notice that there is a window of time
between when futex_requeue() unlocks the hb locks and when
futex_wait_requeue_pi() will acquire hb2->lock. During this
time the pi_state and uval are not in sync with the underlying
rtmutex owner (but the uval does indicate there are waiters, so
no atomic changes will occur in userspace). However, this is
not a problem. Should a contending thread enter
lookup_pi_state() and acquire hb2->lock before the ownership is
fixed up, it will find the pi_state hung off a waiter's
(possibly the pending owner's) futex_q and block on the
rtmutex. Once futex_wait_requeue_pi() fixes up the owner, it
will also move the pi_state from the old owner's
task->pi_state_list to its own.
v3: Fix plist lock name for application to mainline (rather
than -rt) Compile tested against tip/v2.6.31-rc5.
Signed-off-by: Darren Hart <dvhltc@us.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Dinakar Guniguntala <dino@in.ibm.com>
Cc: John Stultz <johnstul@linux.vnet.ibm.com>
LKML-Reference: <4A7F4EFF.6090903@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On an iMac G5, the b43 driver is failing to initialise because trying to
set the dma mask to 30-bit fails. Even though there's only 512MiB of RAM
in the machine anyway:
https://bugzilla.redhat.com/show_bug.cgi?id=514787
We should probably let it succeed if the available RAM in the system
doesn't exceed the requested limit.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If the length is less or equal to frag_prefix_size in the first iteration
we write skb_frags_rx[-1] and read from priv->frag_info[-1]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
