In CLKENA register, can support 16-SD card clocks.
If support correctly, must shift with slot-id.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SD card read was failing (data crc error) on some cards at
maximum possible frequency on P1010 (CCB frequency set to 400MHz).
Some clock deviations are also observed at this frequency.
Hence reduced the mmc clock freq.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Singed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is added just debug message. Almost features need to use the
CMD23. But we didn't see the debug message for sbc. If sbc's message
can see, should be help for debugging. (We can check whether use the
cmd23 or not.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch implements pre_req and post_req in dw_mmc to support
asynchronous mmc request.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Tegra30 differs from Tegra20 in a number of ways. This patch implements a
minimal set of differences in order to get the Cardhu board's SD slot and
eMMC working. Given the diffs between the mainline sdhci-tegra.c and our
downstream versions, I expect we'll eventually need to add many more
differences, hence the seemingly heavy-weight addition of the soc_data
structure.
* Tegra30 doesn't need to override register access to SDHCI_HOST_VERSION or
SDHCI_INT_ENABLE.
* Tegra30 needs quirk SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For FSL ESDHC controllers, when entering sleep the controller will power off,
therefore the registers will lose their values, and the driver should save
the value of registers during suspend and write them back during resume.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some platforms require saving/restoring registers across suspend/resume;
this hook allows them to do that inside their driver.
Signed-off-by: Chris Ball <cjb@laptop.org>
When use the IDMAC, we can also want to use the pdata->blk-setting.
So if pdata->blk-setting is unset, use the default value.
if not, use the pdata->blk-setting.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Support of PCI mode for the dw_mmc driver. This Patch adds the
support for the scenario where the Synopsys Designware IP
is present on the PCI bus. The patch adds the minimal modifications
necessary for the driver to work on PCI platform. Also added separate
files for PCI and PLATFORM modes of operation.
Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds the capability of power off notify for dw-mmc controller.
In order to use Girish's patch:
mmc: core: Add Power Off Notify Feature eMMC 4.5
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC-4.5 data tag feature will be used to store the file system meta-data
in the tagged region of eMMC. This will improve the write and subsequent
read transfer time for the meta data.
Signed-off-by: Saugata Das <saugata.das@linaro.org>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
"[PATCH 0/3] RFC - module.h usage cleanups in fs/ and lib/"
https://lkml.org/lkml/2012/2/29/589
--
Fix up files in fs/ and lib/ dirs to only use module.h if they really
need it.
These are trivial in scope vs. the work done previously. We now have
things where any few remaining cleanups can be farmed out to arch or
subsystem maintainers, and I have done so when possible. What is
remaining here represents the bits that don't clearly lie within a
single arch/subsystem boundary, like the fs dir and the lib dir.
Some duplicate includes arising from overlapping fixes from
independent subsystem maintainer submissions are also quashed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPbNw3AAoJEOvOhAQsB9HWA7wQALrsQ6V6Z+B3KsvSoD5kFnpZ
Y+4uggs+GdUdWmtRrZnTBp896gGuUgBxc3syA2XWd7Oqi49+c5c1m0cFxKyVdIHm
fB+jmxS69soADtHR3cXmxcQshrUzUf2rTn8frcw4O/BmJuplv4xT9uPQzwGaRSZT
gomQsQ1bGnkwjO2jfS8f/N5Mjr8u/z0WF7TTOTUSq+Cv3BervPaSPF1Ea6J8oo+N
4+/n8RlU1HWiI4inrgrFPN6UHmE45BAL2xGbB47LgooHJW8P5kAnU+vxGScaoy1Q
JKX9WKT3VCiwR3VOPa86iLKP3Y8a3VlhyGn+yzzcYkGX/n0tbT7aoRhQm21sGIv0
DoeXWe7aiiY8cEW69G6GIfRPFl+Zh81m1Whbu7IZT/sV3asx6jWmEXE8CgCfeDt5
mNQk9D4Irf6+rmCSbeSVC4L0eFfLxNFouNyh2aus/q+gIjKNKYwZQryHrodK4wpv
UgMKSTZfPrTAWay2gCNWNqo3Zs8e1LDqkftetxeU3jx2kTuaNzBl4Y7mhsX7sLYe
MsFX3JUJ2pn6XWbgqcY+bdr/mzgsCrjzqdf15MTUzEc5SIfVF+XpNNZN1ITwl6UA
/ZH9keBu1mEdCoPU5W74kYwx4p35hIeWJGfc0MRp07ruf941F+SBgMD11B0+06f0
pN0DcITTkD16+sS4x1cB
=Z4w0
-----END PGP SIGNATURE-----
Merge tag 'module-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull cleanup of fs/ and lib/ users of module.h from Paul Gortmaker:
"Fix up files in fs/ and lib/ dirs to only use module.h if they really
need it.
These are trivial in scope vs the work done previously. We now have
things where any few remaining cleanups can be farmed out to arch or
subsystem maintainers, and I have done so when possible. What is
remaining here represents the bits that don't clearly lie within a
single arch/subsystem boundary, like the fs dir and the lib dir.
Some duplicate includes arising from overlapping fixes from
independent subsystem maintainer submissions are also quashed."
Fix up trivial conflicts due to clashes with other include file cleanups
(including some due to the previous bug.h cleanup pull).
* tag 'module-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
lib: reduce the use of module.h wherever possible
fs: reduce the use of module.h wherever possible
includecheck: delete any duplicate instances of module.h
Pull #2 ARM updates from Russell King:
"Further ARM AMBA primecell updates which aren't included directly in
the previous commit. I wanted to keep these separate as they're
touching stuff outside arch/arm/."
* 'amba' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7362/1: AMBA: Add module_amba_driver() helper macro for amba_driver
ARM: 7335/1: mach-u300: do away with MMC config files
ARM: 7280/1: mmc: mmci: Cache MMCICLOCK and MMCIPOWER register
ARM: 7309/1: realview: fix unconnected interrupts on EB11MP
ARM: 7230/1: mmc: mmci: Fix PIO read for small SDIO packets
ARM: 7227/1: mmc: mmci: Prepare for SDIO before setting up DMA job
ARM: 7223/1: mmc: mmci: Fixup use of runtime PM and use autosuspend
ARM: 7221/1: mmc: mmci: Change from using legacy suspend
ARM: 7219/1: mmc: mmci: Change vdd_handler to a generic ios_handler
ARM: 7218/1: mmc: mmci: Provide option to configure bus signal direction
ARM: 7217/1: mmc: mmci: Put power register deviations in variant data
ARM: 7216/1: mmc: mmci: Do not release spinlock in request_end
ARM: 7215/1: mmc: mmci: Increase max_segs from 16 to 128
Pull #1 ARM updates from Russell King:
"This one covers stuff which Arnd is waiting for me to push, as this is
shared between both our trees and probably other trees elsewhere.
Essentially, this contains:
- AMBA primecell device initializer updates - mostly shrinking the
size of the device declarations in platform code to something more
reasonable.
- Getting rid of the NO_IRQ crap from AMBA primecell stuff.
- Nicolas' idle cleanups. This in combination with the restart
cleanups from the last merge window results in a great many
mach/system.h files being deleted."
Yay: ~80 files, ~2000 lines deleted.
* 'for-armsoc' of git://git.linaro.org/people/rmk/linux-arm: (60 commits)
ARM: remove disable_fiq and arch_ret_to_user macros
ARM: make entry-macro.S depend on !MULTI_IRQ_HANDLER
ARM: rpc: make default fiq handler run-time installed
ARM: make arch_ret_to_user macro optional
ARM: amba: samsung: use common amba device initializers
ARM: amba: spear: use common amba device initializers
ARM: amba: nomadik: use common amba device initializers
ARM: amba: u300: use common amba device initializers
ARM: amba: lpc32xx: use common amba device initializers
ARM: amba: netx: use common amba device initializers
ARM: amba: bcmring: use common amba device initializers
ARM: amba: ep93xx: use common amba device initializers
ARM: amba: omap2: use common amba device initializers
ARM: amba: integrator: use common amba device initializers
ARM: amba: realview: get rid of private platform amba_device initializer
ARM: amba: versatile: get rid of private platform amba_device initializer
ARM: amba: vexpress: get rid of private platform amba_device initializer
ARM: amba: provide common initializers for static amba devices
ARM: amba: make use of -1 IRQs warn
ARM: amba: u300: get rid of NO_IRQ initializers
...
Pull vfs pile 1 from Al Viro:
"This is _not_ all; in particular, Miklos' and Jan's stuff is not there
yet."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (64 commits)
ext4: initialization of ext4_li_mtx needs to be done earlier
debugfs-related mode_t whack-a-mole
hfsplus: add an ioctl to bless files
hfsplus: change finder_info to u32
hfsplus: initialise userflags
qnx4: new helper - try_extent()
qnx4: get rid of qnx4_bread/qnx4_getblk
take removal of PF_FORKNOEXEC to flush_old_exec()
trim includes in inode.c
um: uml_dup_mmap() relies on ->mmap_sem being held, but activate_mm() doesn't hold it
um: embed ->stub_pages[] into mmu_context
gadgetfs: list_for_each_safe() misuse
ocfs2: fix leaks on failure exits in module_init
ecryptfs: make register_filesystem() the last potential failure exit
ntfs: forgets to unregister sysctls on register_filesystem() failure
logfs: missing cleanup on register_filesystem() failure
jfs: mising cleanup on register_filesystem() failure
make configfs_pin_fs() return root dentry on success
configfs: configfs_create_dir() has parent dentry in dentry->d_parent
configfs: sanitize configfs_create()
...
Assorted extensions and fixes including:
* Introduction of early/late suspend/hibernation device callbacks.
* Generic PM domains extensions and fixes.
* devfreq updates from Axel Lin and MyungJoo Ham.
* Device PM QoS updates.
* Fixes of concurrency problems with wakeup sources.
* System suspend and hibernation fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=IGhc
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates for 3.4 from Rafael Wysocki:
"Assorted extensions and fixes including:
* Introduction of early/late suspend/hibernation device callbacks.
* Generic PM domains extensions and fixes.
* devfreq updates from Axel Lin and MyungJoo Ham.
* Device PM QoS updates.
* Fixes of concurrency problems with wakeup sources.
* System suspend and hibernation fixes."
* tag 'pm-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (43 commits)
PM / Domains: Check domain status during hibernation restore of devices
PM / devfreq: add relation of recommended frequency.
PM / shmobile: Make MTU2 driver use pm_genpd_dev_always_on()
PM / shmobile: Make CMT driver use pm_genpd_dev_always_on()
PM / shmobile: Make TMU driver use pm_genpd_dev_always_on()
PM / Domains: Introduce "always on" device flag
PM / Domains: Fix hibernation restore of devices, v2
PM / Domains: Fix handling of wakeup devices during system resume
sh_mmcif / PM: Use PM QoS latency constraint
tmio_mmc / PM: Use PM QoS latency constraint
PM / QoS: Make it possible to expose PM QoS latency constraints
PM / Sleep: JBD and JBD2 missing set_freezable()
PM / Domains: Fix include for PM_GENERIC_DOMAINS=n case
PM / Freezer: Remove references to TIF_FREEZE in comments
PM / Sleep: Add more wakeup source initialization routines
PM / Hibernate: Enable usermodehelpers in hibernate() error path
PM / Sleep: Make __pm_stay_awake() delete wakeup source timers
PM / Sleep: Fix race conditions related to wakeup source timer function
PM / Sleep: Fix possible infinite loop during wakeup source destruction
PM / Hibernate: print physical addresses consistently with other parts of kernel
...
Add inline wrappers for device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to hide new parameter from current users of affected interfaces.
Convert current users to use new wrappers instead of direct calls.
Suggested by Russell King [https://lkml.org/lkml/2012/2/3/269].
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Pull trivial tree from Jiri Kosina:
"It's indeed trivial -- mostly documentation updates and a bunch of
typo fixes from Masanari.
There are also several linux/version.h include removals from Jesper."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (101 commits)
kcore: fix spelling in read_kcore() comment
constify struct pci_dev * in obvious cases
Revert "char: Fix typo in viotape.c"
init: fix wording error in mm_init comment
usb: gadget: Kconfig: fix typo for 'different'
Revert "power, max8998: Include linux/module.h just once in drivers/power/max8998_charger.c"
writeback: fix fn name in writeback_inodes_sb_nr_if_idle() comment header
writeback: fix typo in the writeback_control comment
Documentation: Fix multiple typo in Documentation
tpm_tis: fix tis_lock with respect to RCU
Revert "media: Fix typo in mixer_drv.c and hdmi_drv.c"
Doc: Update numastat.txt
qla4xxx: Add missing spaces to error messages
compiler.h: Fix typo
security: struct security_operations kerneldoc fix
Documentation: broken URL in libata.tmpl
Documentation: broken URL in filesystems.tmpl
mtd: simplify return logic in do_map_probe()
mm: fix comment typo of truncate_inode_pages_range
power: bq27x00: Fix typos in comment
...
Conflicts:
arch/arm/mach-lpc32xx/clock.c
arch/arm/mach-pxa/pxa25x.c
arch/arm/mach-pxa/pxa27x.c
The conflicts with pxa are non-obvious, we have multiple branches
adding and removing the same clock settings. According to
Haojian Zhuang, removing the sa1100 rtc dummy clock is the correct
fix here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here's the big serial and tty merge for the 3.4-rc1 tree.
There's loads of fixes and reworks in here from Jiri for the tty layer,
and a number of patches from Alan to help try to wrestle the vt layer
into a sane model.
Other than that, lots of driver updates and fixes, and other minor
stuff, all detailed in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9nihQACgkQMUfUDdst+ylXTQCdFuwVuZgjCts+xDVa1jX2ac84
UogAn3Wr+P7NYFN6gvaGm52KbGbZs405
=2b/l
-----END PGP SIGNATURE-----
Merge tag 'tty-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY/serial patches from Greg KH:
"tty and serial merge for 3.4-rc1
Here's the big serial and tty merge for the 3.4-rc1 tree.
There's loads of fixes and reworks in here from Jiri for the tty
layer, and a number of patches from Alan to help try to wrestle the vt
layer into a sane model.
Other than that, lots of driver updates and fixes, and other minor
stuff, all detailed in the shortlog."
* tag 'tty-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (132 commits)
serial: pxa: add clk_prepare/clk_unprepare calls
TTY: Wrong unicode value copied in con_set_unimap()
serial: PL011: clear pending interrupts
serial: bfin-uart: Don't access tty circular buffer in TX DMA interrupt after it is reset.
vt: NULL dereference in vt_do_kdsk_ioctl()
tty: serial: vt8500: fix annotations for probe/remove
serial: remove back and forth conversions in serial_out_sync
serial: use serial_port_in/out vs serial_in/out in 8250
serial: introduce generic port in/out helpers
serial: reduce number of indirections in 8250 code
serial: delete useless void casts in 8250.c
serial: make 8250's serial_in shareable to other drivers.
serial: delete last unused traces of pausing I/O in 8250
pch_uart: Add module parameter descriptions
pch_uart: Use existing default_baud in setup_console
pch_uart: Add user_uartclk parameter
pch_uart: Add Fish River Island II uart clock quirks
pch_uart: Use uartclk instead of base_baud
mpc5200b/uart: select more tolerant uart prescaler on low baudrates
tty: moxa: fix bit test in moxa_start()
...
For simple modules that contain a single amba_driver without any
additional setup code then ends up being a block of duplicated
boilerplate. This patch adds a new macro, module_amba_driver(),
which replaces the module_init()/module_exit() registrations with
template functions.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* pm-qos:
sh_mmcif / PM: Use PM QoS latency constraint
tmio_mmc / PM: Use PM QoS latency constraint
PM / QoS: Make it possible to expose PM QoS latency constraints
* 'ep93xx-for-arm-soc' of git://github.com/RyanMallon/linux-2.6:
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
(update to v3.3-rc7)
Conflicts:
arch/arm/mach-s3c2440/common.h
* 'next/devel-samsung-mmc' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: change the name from s3c-sdhci to exynos4-sdhci
mmc: sdhci-s3c: add platform data for the second capability
ARM: SAMSUNG: support the second capability for samsung-soc
Make sh_mmcif call dev_pm_qos_expose_latency_limit() to expose
the PM QoS latency limit to user space and specify the initial
value of it as 100 microseconds.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Make tmio_mmc call dev_pm_qos_expose_latency_limit() to expose
the PM QoS latency limit to user space and specify the initial
value of it as 100 microseconds.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch is added host_caps2 in sdhci-s3c.c
It's necessary that use the second capabilities.
And removed the duplicated host_caps.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
All num, magic and owner are set by alloc_tty_driver. No need to
re-set them on each allocation site.
pti driver sets something different to what it passes to
alloc_tty_driver. It is not a bug, since we don't use the lines
parameter in any way. Anyway this is fixed, and now we do the right
thing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even if cards supports 1.8V I/O voltage those should anyway be
initialized at 3.3V I/O according to (e)MMC, SD and SDIO specs.
Some eMMC and embedded SDIO devices are able to be initialized
at 1.8V as well, but it is better to be safe.
Do note that initialization in this context means that the card
has been completely powered off, otherwise the card will remain
at the last I/O voltage level that were negotitiated.
Due to the above being taken care of the suspend/resume issues
for UHS-I SD-cards has been fixed.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
On a system with large pages (64k in my case), the following BUG is
triggered in MMC core:
[ 2.338023] BUG: failure at drivers/mmc/core/core.c:221/mmc_start_request()!
[ 2.338102] Kernel panic - not syncing: BUG!
[ 2.338155] Call trace:
[ 2.338228] [<ffffffc00008635c>] dump_backtrace+0x0/0x120
[ 2.338317] [<ffffffc0003365ec>] dump_stack+0x14/0x1c
[ 2.338403] [<ffffffc000336990>] panic+0xbc/0x1f0
[ 2.338498] [<ffffffc00027a494>] mmc_start_request+0x154/0x184
[ 2.338600] [<ffffffc00027abdc>] mmc_start_req+0x110/0x140
[ 2.338701] [<ffffffc00028604c>] mmc_blk_issue_rw_rq+0x7c/0x39c
[ 2.338804] [<ffffffc00028652c>] mmc_blk_issue_rq+0x1c0/0x468
[ 2.338905] [<ffffffc000287564>] mmc_queue_thread+0x68/0x118
[ 2.338995] [<ffffffc0000bc308>] kthread+0x84/0x8c
This is because of a 64k request with a max_req_size of 64k-1 bytes.
The following patch fixes the problem by limiting the max_blk_count
such that max_blk_count * max_blk_size == max_req_size. I couldn't
pursuade the compiler to emit a shift instead of a div without encoding
the shift explicitly.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
On i.MX53 we have to write a special SDHCI_CMD_ABORTCMD to the
SDHCI_TRANSFER_MODE register during a MMC_STOP_TRANSMISSION
command. This works for SD cards. However, with MMC cards
the MMC_SET_BLOCK_COUNT command is used instead, but this
needs the same handling. Fix MMC cards by testing for the
MMC_SET_BLOCK_COUNT command aswell. Tested on a custom i.MX53
board with a Transcend MMC+ card and eMMC.
The kernel started used MMC_SET_BLOCK_COUNT in 3.0, so this
is a regression for these boards introduced in 3.0; it should
go to 3.0/3.1/3.2-stable.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
A recent commit "mmc: core: Use delayed work in clock gating framework"
(597dd9d79c) introduced a default 200ms delay before clock gating
actually takes place. This means that every time an MMC interface
becomes idle it first stays on for 200ms before gating its clock. This
leads to increased power consumption and is therefore a clear regression.
This patch restores the original behaviour by setting the default delay
to 0. Users prioritising throughput over power efficiency can still
modify the delay via sysfs.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch changes the ARCH name to "ARCH_S3C24XX" for Samsung
S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443,
and S3C2450 SoCs so that we can merge the mach-xxx directories
and plat-s3c24xx dir. to just one mach-s3c24xx for them.
I think this should be sent to upstream via samsung tree because
this touches many samsung stuff.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
[for the gadget part:]
Acked-by: Felipe Balbi <balbi@ti.com>
[for the framebuffer (video) part:]
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
[For the watchdog-part:]
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Some callbacks are set too early -- i.e. we can have dma capabilities but
we can't get a dma channel. So wait to get the dma channel before setting
callbacks and change logs consequently.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[Should be applied to 3.2-stable.]
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Different tree maintainers picked up independently generated
trivial compile fixes based on linux-next testing, resulting
in some cases where a file would have got more than one addition
of module.h once everything was all merged together.
Delete any duplicates so includecheck isn't complaining about
anything related to module.h/export.h changes.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* lpc32xx/drivers: (566 commits)
ARM: LPC32xx: ADC support for mach-lpc32xx
Includes an update to Linux 3.3-rc4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are few existing user drivers of dw_dmac. They will break as soon as we
remove unused fields from struct dw_dma_slave. This patch focuses to fix these
user drivers to use dma_slave_config() routine.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
.device_fc is added in struct dma_slave_config recently. All user drivers, which
want DMA to be the flow controller must pass this field as false. As earlier
driver don't look to use this feature, mark it false for now.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Sometimes a software reset is needed. Then some registers are saved and
restored but the interrupt mask register is missing. It causes issues
with sdio devices whose interrupts are masked after reset.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If the driver is loaded with a card in the slot, mmc_add_host() will
schedule an immediate card-detection work, which will start IO and wait
for command completion. Usually the kernel first returns to the sh_mmcif
probe function, lets it finish and only then schedules the rescan work.
But sometimes, expecially under heavy system load, the work will be
scheduled immediately before returning to the probe method. In this case
it is important for the driver to be fully prepared for IO. For sh_mmcif
this means, that also the timeout work has to be initialised before
calling mmc_add_host(). It is also better to prepare interrupts
beforehand. Besides, since mmc_add_host() does card-detection itself,
there is no need to do it again immediately afterwards.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
When DMA is in use and the card is ejected during IO, DMA transfers have to
be terminated, otherwise the dmaengine driver fails to operate properly,
when the card is re-inserted.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Found this issue during code review. Actually, there are two issues which
both compensate together in lucky case. In unlucky case the bus width
probing might not work as expected.
Signed-off-by: Jurgen Heeks <jurgen.heeks@nokia.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Modified the mmc_poweroff to resume before sending the poweroff
notification command. In sleep mode only AWAKE and RESET commands are
allowed, so before sending the poweroff notification command resume from
sleep mode and then send the notification command.
PowerOff Notify is tested on a Synopsis Designware Host Controller
(eMMC 4.5). The suspend to RAM and resume works fine.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Tested-by: Girish K S <girish.shivananjappa@linaro.org>
Reviewed-by: Saugata Das <saugata.das@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Set Medfield SDIO as non-removable to avoid un-necessary
card detect activity.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There is an understood mismatch between the voltage the host controller is
set to and the voltage supplied to the card by a fixed voltage regulator.
Teaching the driver to accept the mismatch is overly complicated. Instead
just accept the regulator's voltage.
This patch adds MMC_CAP2_BROKEN_VOLTAGE.
If the voltage didn't satisfy between min_uV and max_uV, try to change
the voltage in core.c. When changing the voltage, maybe use
regulator_set_voltage().
In regulator_set_voltage(), check the below condition.
/* sanity check */
if (!rdev->desc->ops->set_voltage &&
!rdev->desc->ops->set_voltage_sel) {
ret = -EINVAL;
goto out;
}
If some board should use the fixed-regulator, always return -EINVAL.
Then, eMMC didn't initialize always.
So if use a fixed-regulator, we need to add the MMC_CAP2_BROKEN_VOLTAGE.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes the failure of low speed mmc card detection.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When accessing the card on some FSL platform boards (e.g p2020, p1010,
mpc8536), the following error is reported with the timeout value calculated:
mmc0: Got data interrupt 0x00000020 even though no data operation was
in progress.
mmc0: Got data interrupt 0x00000020 even though no data operation was
in progress.
So we skip the calculation of timeout and use the max value to fix it.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Gao Guanhua <B22826@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For some FSL ESDHC controllers (e.g. P2020E, Rev1.0), the SDHC can not
work on DMA mode because of the hardware bug, so we set a broken dma flag
and use PIO mode.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Gao Guanhua <B22826@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ensure clocks are always enabled before any interaction with the
host controller driver. This makes sure that there is no race
between host execution and the core layer turning off clocks
in different context with clock gating framework.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The voltage_ranges is supposed to switch from big endian to little endian.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Chris Ball <cjb@laptop.org>
A UHS sdio card that fails initialization at 1.8v signaling is not in
UHS mode. We cannot use the speed in the the cis to reflect the bus
speed as this is the maxiumum value and will not reflect the fact
that the host is operating at a lower (non uhs) bus speed.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Reviewed-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When eSDHC module is enabled on P5020/P3041/P2041/P1010 with eSDHC
version 2.3, there is following errors:
mmc0: Timeout waiting for hardware interrupt.
mmc0: error -110 whilst initialising SD card
mmc0: Unexpected interrupt 0x02000000.
mmc0: Timeout waiting for hardware interrupt.
mmc0: error -110 whilst initialising SD card
mmc0: Unexpected interrupt 0x02000000.
It is because eSDHC controller has different bit setting for PROCTL
register at 0x28 comparing SD specification.
This patch sets DMAS bits correctly for byte operation and does not
change the default value of other field of PROCTL register.
For other FSL chips, such as MPC8536/P2020, PROCTL[DMAS]
bits are reserved and even if they are set to wrong bits, it will not
take effective.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Following removal announce and addition to feature-removal-schedule.txt,
here is the actual source code deletion for Atmel CAP9 family.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use the helper in the rest of the tty drivers. This is a simple
replacement.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of reading a register value everytime we need to
apply a new value for it, maintain a cached copy for it.
This also means we are able to skip writes that are not
needed.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MISC_DEVICES option alone does not select any kernel code and can cause dependency build warnings, such as:
warning: (KS8851 && AX88796_93CX6 && RTL8180 && RTL8187 && ADM8211 && RT2400PCI && RT2500PCI && RT61PCI && RT2800PCI && R8187SE) selects EEPROM_93CX6 which has unmet direct dependencies (MISC_DEVICES)
As the current drivers/misc/Kconfig stands, it is only possible to select the drivers below if MISC_DEVICES option is selected:
source "drivers/misc/c2port/Kconfig"
source "drivers/misc/eeprom/Kconfig"
source "drivers/misc/cb710/Kconfig"
source "drivers/misc/iwmc3200top/Kconfig"
source "drivers/misc/ti-st/Kconfig"
source "drivers/misc/lis3lv02d/Kconfig"
source "drivers/misc/carma/Kconfig"
source "drivers/misc/altera-stapl/Kconfig"
So remove MISC_DEVICES option so that nothing is dependant on it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Corrects a bug in MMCI host driver which silently causes
small reads (< 4 bytes as only used in SDIO) from PL-18X to fail.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Fredrik Soderstedt <fredrik.soderstedt@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the SDIO preparation to be done before the DMA job is setup.
This makes it possible to do DMA for SDIO transfers as well as the
earlier supported pio mode.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Added use of runtime PM autosuspend feature, with a fixed
timeout of 50 ms. This will prevent adding a latency,
although very minor, for _every_ request.
Moreover the runtime_get_sync is now also used in set_ios and
suspend since the runtime resourses are needed here as well.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch switch from using the legacy suspend/resume
to the new way of registering PM callbacks. No functional
change is done.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The purpose of the vdd_handler does not make sense. We remove it
and use a generic approach instead. A new ios_handler is added, the
purpose of which e.g. can be to control GPIO pins to a levelshifter.
Previously the vdd_handler was also used for making additional
changes to the power register bits. This option is superfluous and is
therefore removed.
Adaptaptions from the old vdd_handler to the new ios_handler is done for
mach-ux500 board, which was the only one using the vdd_handler.
This patch is based upon a patch from Sebastian Rasmussen.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ST Micro variant supports bus signal direction indication. A new
member in the variant struct is added for this.
Moreover the actual signal direction configuration is board specific,
thus the amba mmci platform data is extended with a new member to be
able provide mmci with these specific board configurations.
This patch is based upon a patch from Sebastian Rasmussen.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use variant data to store hardware controller deviations concerning
power registers to improve readability of the code.
Signed-off-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch "mmc: core: move ->request() call from atomic context",
is the reason to why this change is possible. This simplifies the
error handling code execution path quite a lot and potentially also
fixes some error handling hang problems.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A significant increase (10-20%) in performance throughput for
USB mass storage is the reason for incrementing the value.
By some reason the USB driver allocates buffers which requires
a scattergather list to contain a lot more than 16 elements to
get optimal performance. This change sets the maximum elements
to 128.
Tests with large reads and large writes (100 MiB) show that the
throughput increase is significant for write (10% for this test)
but not for read. Tests are run on a Linux host with ext4 FS on
the gadget mass storage device. The sg-len still exceeds 16 for
the read tests but the performance gain is low or nothing.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HHrh
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://github.com/rustyrussell/linux
Autogenerated GPG tag for Rusty D1ADB8F1: 15EE 8D6C AB0E 7F0C F999 BFCB D920 0E6C D1AD B8F1
* tag 'for-linus' of git://github.com/rustyrussell/linux:
module_param: check that bool parameters really are bool.
intelfbdrv.c: bailearly is an int module_param
paride/pcd: fix bool verbose module parameter.
module_param: make bool parameters really bool (drivers & misc)
module_param: make bool parameters really bool (arch)
module_param: make bool parameters really bool (core code)
kernel/async: remove redundant declaration.
printk: fix unnecessary module_param_name.
lirc_parallel: fix module parameter description.
module_param: avoid bool abuse, add bint for special cases.
module_param: check type correctness for module_param_array
modpost: use linker section to generate table.
modpost: use a table rather than a giant if/else statement.
modules: sysfs - export: taint, coresize, initsize
kernel/params: replace DEBUGP with pr_debug
module: replace DEBUGP with pr_debug
module: struct module_ref should contains long fields
module: Fix performance regression on modules with large symbol tables
module: Add comments describing how the "strmap" logic works
Fix up conflicts in scripts/mod/file2alias.c due to the new linker-
generated table approach to adding __mod_*_device_table entries. The
ARM sa11x0 mcp bus needed to be converted to that too.
Core:
* Support for the HS200 high-speed eMMC mode.
* Support SDIO 3.0 Ultra High Speed cards.
* Kill pending block requests immediately if card is removed.
* Enable the eMMC feature for locking boot partitions read-only
until next power on, exposed via sysfs.
Drivers:
* Runtime PM support for Intel Medfield SDIO.
* Suspend/resume support for sdhci-spear.
* sh-mmcif now processes requests asynchronously.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LJnN
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
MMC highlights for 3.3:
Core:
* Support for the HS200 high-speed eMMC mode.
* Support SDIO 3.0 Ultra High Speed cards.
* Kill pending block requests immediately if card is removed.
* Enable the eMMC feature for locking boot partitions read-only
until next power on, exposed via sysfs.
Drivers:
* Runtime PM support for Intel Medfield SDIO.
* Suspend/resume support for sdhci-spear.
* sh-mmcif now processes requests asynchronously.
* tag 'mmc-merge-for-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (58 commits)
mmc: fix a deadlock between system suspend and MMC block IO
mmc: sdhci: restore the enabled dma when do reset all
mmc: dw_mmc: miscaculated the fifo-depth with wrong bit operation
mmc: host: Adds support for eMMC 4.5 HS200 mode
mmc: core: HS200 mode support for eMMC 4.5
mmc: dw_mmc: fixed wrong bit operation for SDMMC_GET_FCNT()
mmc: core: Separate the timeout value for cache-ctrl
mmc: sdhci-spear: Fix compilation error
mmc: sdhci: Deal with failure case in sdhci_suspend_host
mmc: dw_mmc: Clear the DDR mode for non-DDR
mmc: sd: Fix SDR12 timing regression
mmc: sdhci: Fix tuning timer incorrect setting when suspending host
mmc: core: Add option to prevent eMMC sleep command
mmc: omap_hsmmc: use threaded irq handler for card-detect.
mmc: sdhci-pci: enable runtime PM for Medfield SDIO
mmc: sdhci: Always pass clock request value zero to set_clock host op
mmc: sdhci-pci: remove SDHCI_QUIRK2_OWN_CARD_DETECTION
mmc: sdhci-pci: get gpio numbers from platform data
mmc: sdhci-pci: add platform data
mmc: sdhci: prevent card detection activity for non-removable cards
...
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Performing MMC block IO with simultaneous STR can lead to a deadlock: the
mmc_pm_notify() function claims the host and then calls bus .remove()
method, which lands in mmc_blk_remove(), which calls mmc_blk_remove_req()
then it goes to -> mmc_cleanup_queue() -> kthread_stop(), which waits for
the mmc-block thread to stop. If the mmc-block thread at that time is
processing block requests, it will also try to claim the host in
mmc_blk_issue_rq() and block there. This patch fixes the problem by
calling .remove() before claiming the host.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If dma is enabled, it'll be cleared when reset all is performed, this can
be observed on some platforms, such as P2041 which has a version 2.3
controller, but platform like P4080 which has a version 2.2 controller,
does not suffer this, so we will check if the dma is enabled, we should
restore it after reset all.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In FIFOTH register, the RX_WMark field (bits[27:16]) defaults to
FIFO_DEPTH - 1. When reading it, bits[26:16] were being used, so
fix it to use the mask 0xfff instead of 0x7ff.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for the HS200 mode on the host side.
Also enables the tuning feature required when the HS200 mode
is selected.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds the support of the HS200 bus speed for eMMC 4.5 devices.
The eMMC 4.5 devices have support for 200MHz bus speed. The function
prototype of the tuning function is modified to handle the tuning
command number which is different in sd and mmc case.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In status register, fifo_count is bit[29:17].
(0x1FFF is correct)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Turning the cache off implies flushing cache which doesn't define
maximum timeout unlike cache-on. This patch will apply the generic
CMD6 timeout only for cache-on. Additionally the kernel message is
added for checking failure case of cache-on.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
With the inclusion of following patch (59b5bc3929b37):
"mmc: sdhci: remove "state" argument from sdhci_suspend_host"
we get a compilation error for sdhci-spear:
drivers/mmc/host/sdhci-spear.c:283:2: error: too many arguments to function
‘sdhci_suspend_host’
This patch fixes this error.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
If there are errors happened in sdhci_suspend_host, handle it so that
when the function returns with an error, the host's behaviour is the
same before this function call, e.g. card detection is enabled and
tuning timer is active, etc.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
UHS_REG should be cleared for non-DDR mode. But currently there is
no way to clear DDR mode, if it is already set once. This patch adds
clearing DDR mode for non-DDR mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes a failure to recognize SD cards reported on a Dell
Vostro with O2 Micro SD card reader. Patch 49c468f ("mmc: sd: add
support for uhs bus speed mode selection") caused the problem, by
setting the SDHCI_CTRL_HISPD flag even for legacy timings.
Signed-off-by: Alexander Elbs <alex@segv.de>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Arindam Nath <arindam.nath@amd.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When suspending host, the tuning timer shoule be deactivated.
And the HOST_NEEDS_TUNING flag should be set after tuning timer is
deactivated.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host may now use MMC_CAP2_NO_SLEEP_CMD to disable the use
of eMMC sleep/awake command.
This option can be used when your platform has a buggy
kernel crash dump software, which is supposed to store
the dump on the eMMC, but is not able to wake up the eMMC
from sleep state.
In particular, failures have been seen with u-boot; even if
it is fixed there, platforms will be slow to update their
bootloader binaries.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Hanumath Prasad <hanumath.prasad@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
As the card-detect irq handler just schedules work to be done by a
thread, we can use request_threaded_irq to do much of the work for
us. This means that interrupts which arrive by handle_nested_irq
actually work.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Kishore Kadiyala <kishorek.kadiyala@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Runtime PM for SDIO is no longer enabled by default (see
5c7f0e083d) so it must now
be enabled per platform, in this case Medfield uses it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
To allow the set_clock host op to disable the SDCLK source when not
needed, always call the host op when the requested clock speed is
zero. Do this even if host->clock already equals zero, because
the SDHCI driver may set that value (without calling the host op)
to force an update at the next (non-zero-speed) call.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Even if a driver provides separate card detection, an interrupt
is still needed to abort mmc requests that are in progress.
SDHCI_QUIRK2_OWN_CARD_DETECTION prevents that, so remove it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
