* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (57 commits)
drm/i915: Handle ERESTARTSYS during page fault
drm/i915: Warn before mmaping a purgeable buffer.
drm/i915: Track purged state.
drm/i915: Remove eviction debug spam
drm/i915: Immediately discard any backing storage for uneeded objects
drm/i915: Do not mis-classify clean objects as purgeable
drm/i915: Whitespace correction for madv
drm/i915: BUG_ON page refleak during unbind
drm/i915: Search harder for a reusable object
drm/i915: Clean up evict from list.
drm/i915: Add tracepoints
drm/i915: framebuffer compression for GM45+
drm/i915: split display functions by chip type
drm/i915: Skip the sanity checks if the current relocation is valid
drm/i915: Check that the relocation points to within the target
drm/i915: correct FBC update when pipe base update occurs
drm/i915: blacklist Acer AspireOne lid status
ACPI: make ACPI button funcs no-ops if not built in
drm/i915: prevent FIFO calculation overflows on 32 bits with high dotclocks
drm/i915: intel_display.c handle latency variable efficiently
...
Fix up trivial conflicts in drivers/gpu/drm/i915/{i915_dma.c|i915_drv.h}
In order to correctly prevent the invalid reuse of a purged buffer, we
need to track such events and warn the user before something bad
happens.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (133 commits)
drm/vgaarb: add VGA arbitration support to the drm and kms.
drm/radeon: some r420s have a CP race with the DMA engine.
drm/radeon/r600/kms: rv670 is not DCE3
drm/radeon/kms: r420 idle after programming GA_ENHANCE
drm/radeon/kms: more fixes to rv770 suspend/resume path.
drm/radeon/kms: more alignment for rv770.c with r600.c
drm/radeon/kms: rv770 blit init called too late.
drm/radeon/kms: move around new init path code to avoid posting at init
drm/radeon/r600: fix some issues with suspend/resume.
drm/radeon/kms: disable VGA rendering engine before taking over VRAM
drm/radeon/kms: Move radeon_get_clock_info() call out of radeon_clocks_init().
drm/radeon/kms: add initial connector properties
drm/radeon/kms: Use surfaces for scanout / cursor byte swapping on big endian.
drm/radeon/kms: don't fail if we fail to init GPU acceleration
drm/r600/kms: fixup number of loops per blit calculation.
drm/radeon/kms: reprogram format in set base.
drm/radeon: avivo chips have no separate int bit for display
drm/radeon/r600: don't do interrupts
drm: fix _DRM_GEM addmap error message
drm: update crtc x/y when only fb changes
...
Fixed up trivial conflicts in firmware/Makefile due to network driver
(cxgb3) and drm (mga/r128/radeon) firmware being listed next to each
other.
VGA arb requires DRM support for non-kms drivers, to turn on/off
irqs when disabling the mem/io regions.
VGA arb requires KMS support for GPUs where we can turn off VGA
decoding. Currently we know how to do this for intel and radeon
kms drivers, which allows them to be removed from the arbiter.
This patch comes from Fedora rawhide kernel.
Signed-off-by: Dave Airlie <airlied@redhat.com>
fix the following 'make includecheck' warning:
include/drm/drm_memory.h: linux/vmalloc.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <1247068169.4382.99.camel@ht.satnam>
Acked-by: Dave Airlie <airlied@redhat.com>
Userspace can query if acceleration is working or not true get
info ioctl and could fallback to software if for some reason
kernel failed to initialize KMS. This should allow to give a
working KMS setup in all case (even with non functionning accel).
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Similar to the madvise() concept, the application may wish to mark some
data as volatile. That is in the event of memory pressure the kernel is
free to discard such buffers safe in the knowledge that the application
can recreate them on demand, and is simply using these as a cache.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add a function that can be used to add the default mode for the output device
without EDID.
It will add the default mode that meets with the requirements of given
hdisplay/vdisplay limit.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For shared tv-out and VGA encoders, we really need to know if
the encoder is just being switched off temporarily in blanking
or if we are really disabling it hard.
Also we need to try harder to disconnect encoders from unused
connectors so we can share more efficently.
(shared encoders stuff is coming in radeon tv-out support)
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds code to the drm_mm to talk to debugfs, and adds
support to radeon to add the VRAM and GTT mm lists to debugfs.
I tested with spinlock debugging and it doesn't give out.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Initially I always meant this code to be shared, but things
ran away from me before I got to it.
This refactors the i915 and radeon kms fbdev interaction layers
out into generic helpers + driver specific pieces.
It moves all the panic/sysrq enhancements to the core file,
and stores a linked list of kernel fbs. This could possibly be
improved to only store the fb which has fbcon on it for panics
etc.
radeon retains some specific codes used for a big endian
workaround.
changes:
fix oops in v1
fix freeing path for crtc_info
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Several functions in the GEM kernel API used int as handle type, but
user API has it __u32 which is also the intended type.
Replace int with u32.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The previous patch assumes the ioctl already existed, when
it actually didn't.
It also didn't return the correct error code.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Common resources, like memory accounting and swap lists should be
global and not per device. Introduce a struct ttm_bo_global to
accomodate this, and register it with sysfs. Add a small sysfs interface
to return the number of active buffer objects.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Use inclusive zones to simplify accounting and its sysfs representation.
Use DMA32 accounting where applicable.
Add a sysfs interface to make the heuristically determined limits
readable and configurable.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Export utility functions for drivers to add specialized devices in the
sysfs drm class subdirectory.
Initially this will be needed form TTM to add a virtual device that
handles power management.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
A micro-optimization on the function ttm_kmap_obj_virtual().
By defining the values of enum ttm_bo_kmap_obj::bo_kmap_type to have a
bit indicating iomem, size of the function ttm_kmap_obj_virtual() will be
reduced by 16 bytes on x86_64 (gcc 4.1.2).
ttm_kmap_obj_virtual() may be heavily used, when buffer objects are
accessed via wrappers, that work for both kinds of memory addresses:
iomem cookies and kernel virtual.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now that we're using the scaling property in the Intel driver I noticed
that the names were a bit confusing. I've corrected them according to
our discussion on IRC and the mailing list, though I've left out
potential new additions for a new scaling property with an integer (or
two) for the scaling factor. None of the drivers implement that today,
but if someone wants to do it, I think it could be done with the
addition of a single new type and a new property to describe the
scaling factor in the X and Y directions.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This implements the busy ioctl along with a current domain check.
returns 0 or -EBUSY
puts the current domain no matter what the answer.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Overscan, saturation, hue. Used in the nouveau driver for GPUs with
integrated TV encoders.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Namely "brightness", "contrast" and "flicker reduction".
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The existing TV connector types are often unsuitable either because
there is no way to probe them until they're actually plugged in or
because they can change during run time (e.g. 7-pin DIN connectors
that behave as S-Video, Component, Composite or SCART depending on the
adaptor plugged in).
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Define some helper functions to make easier to detach a KMS encoder
implementation from the drm module of the GPU it's used in. This is
mainly useful for some external I2C encoders known to be present on
cards with GPUs from several different manufacturers.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add the explanation about DRM debug level in the drmP header file. This is to
explain how/where to use the different DRM debug level.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Two macro definitions of DRM_DEBUG_KMS/MODE can be used to add the debug
info related with KMS. It is confusing.
So remove the macro definition of DRM_DEBUG_MODE. Instead it can be replaced
by the DRM_DEBUG_KMS.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We will have to add a prefix when using the macro defintion of DRM_DEBUG_KMS
/DRM_DEBUG_DRIVER/MODE. It is not convenient. We should use the DRM_NAME
as default prefix.
So remove the prefix in the macro definition of DRM_DEBUG_KMS/DRIVER/MODE.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-radeon-kms' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (35 commits)
drm/radeon: set fb aperture sizes for framebuffer handoff.
drm/ttm: fix highuser vs dma32 confusion.
drm/radeon: Fix size used for benchmarking BO copies.
drm/radeon: Add radeon.test parameter for running BO GPU copy tests.
drm/radeon/kms: allow interruptible waits for objects.
drm/ttm: powerpc: Fix Highmem cache flushing.
x86: Export kmap_atomic_prot() needed for TTM.
drm/ttm: Fix ttm in-kernel copying of pages with non-standard caching attributes.
drm/ttm: Fix an oops and sync object leak.
drm/radeon/kms: vram sizing on certain r100 chips needs workaround.
drm/radeon: Pay more attention to object placement requested by userspace.
drm/radeon: Fall back to evicting BOs with memcpy if necessary.
drm/radeon: Don't unreserve twice on failure to validate.
drm/radeon/kms: fix bandwidth computation on avivo hardware
drm/radeon/kms: add initial colortiling support.
drm/radeon/kms: fix hotspot handling on pre-avivo chips
drm/radeon/kms: enable frac fb divs on rs600/rs690/rs740
drm/radeon/kms: add PLL flag to prefer frequencies <= the target freq
drm/radeon/kms: block RN50 from using 3D engine.
drm/radeon/kms: fix VRAM sizing like DDX does it.
...
This adds new set/get tiling interfaces where the pitch
and macro/micro tiling enables can be set. Along with
a flag to decide if this object should have a surface when mapped.
The only thing we need to allocate with a mapped surface should be
the frontbuffer. Note rotate scanout shouldn't require one, and
back/depth shouldn't either, though mesa needs some fixes.
It fixes the TTM interfaces along Thomas's suggestions, and I've tested
the surface stealing code with two X servers and not seen any lockdep issues.
I've stopped tiling the fbcon frontbuffer, as I don't see there being
any advantage other than testing, I've left the testing commands in there,
just flip the fb_tiled to true in radeon_fb.c
Open: Can we integrate endian swapping in with this?
Future features:
texture tiling - need to relocate texture registers TXOFFSET* with tiling info.
This also merges Michel's cleanup surfaces regs at init time patch
even though it makes sense on its own, this patch really relies on it.
Some PowerMac firmwares set up a tiling surface at the beginning of VRAM
which messes us up otherwise.
that patch is:
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This add support for using dma32 memory on gpus that really need it.
Currently IGPs are left without DMA32 but we might need to change
that unless we can fix rs690.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add the GTF algorithm in kernel space. And this function can be called to
generate the required modeline.
I copied it from the file of xserver/hw/xfree86/modes/xf86gtf.c. What I have
done is to translate it by using integer calculation. This is to avoid
the float-point calculation in kernel space.
At the same tie I also refer to the function of fb_get_mode in
drivers/video/fbmon.c
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Add the CVT algorithm in kernel space. And this function can be called to
generate the required modeline.
I copied it from the file of xserver/hw/xfree86/modes/xf86cvt.c. What I have
done is to translate it by using integer calculation. This is to avoid
the float-point calculation in kernel space.
[airlied:- cleaned up some bits]
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Looks like I managed to mess up most shifts when converting from bitfields. :(
The patch below works on my Thinkpad T500 (as well as on my PowerBook,
where the previous change worked as well, maybe out of luck...). I'd
appreciate more testing and eyes looking over it though.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Tested-by: Michael Pyne <mpyne@kde.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
also for the atomic path by using a common code-path.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It hasn't been used in ages, and having the user tell your how much
memory is being freed at free time is a recipe for disaster even if it
was ever used.
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: switch to using late_initcall
radeon legacy chips: tv dac bg/dac adj updates
drm/radeon: introduce kernel modesetting for radeon hardware
drm: Add the TTM GPU memory manager subsystem.
drm: Memory fragmentation from lost alignment blocks
drm/radeon: fix mobility flags on new PCI IDs.
Add kernel modesetting support to radeon driver, use the ttm memory
manager to manage memory and DRM/GEM to provide userspace API.
In order to avoid backward compatibility issue and to allow clean
design and code the radeon kernel modesetting use different code path
than old radeon/drm driver.
When kernel modesetting is enabled the IOCTL of radeon/drm
driver are considered as invalid and an error message is printed
in the log and they return failure.
KMS enabled userspace will use new API to talk with the radeon/drm
driver. The new API provide functions to create/destroy/share/mmap
buffer object which are then managed by the kernel memory manager
(here TTM). In order to submit command to the GPU the userspace
provide a buffer holding the command stream, along this buffer
userspace have to provide a list of buffer object used by the
command stream. The kernel radeon driver will then place buffer
in GPU accessible memory and will update command stream to reflect
the position of the different buffers.
The kernel will also perform security check on command stream
provided by the user, we want to catch and forbid any illegal use
of the GPU such as DMA into random system memory or into memory
not owned by the process supplying the command stream. This part
of the code is still incomplete and this why we propose that patch
as a staging driver addition, future security might forbid current
experimental userspace to run.
This code support the following hardware : R1XX,R2XX,R3XX,R4XX,R5XX
(radeon up to X1950). Works is underway to provide support for R6XX,
R7XX and newer hardware (radeon from HD2XXX to HD4XXX).
Authors:
Jerome Glisse <jglisse@redhat.com>
Dave Airlie <airlied@redhat.com>
Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
TTM is a GPU memory manager subsystem designed for use with GPU
devices with various memory types (On-card VRAM, AGP,
PCI apertures etc.). It's essentially a helper library that assists
the DRM driver in creating and managing persistent buffer objects.
TTM manages placement of data and CPU map setup and teardown on
data movement. It can also optionally manage synchronization of
data on a per-buffer-object level.
TTM takes care to provide an always valid virtual user-space address
to a buffer object which makes user-space sub-allocation of
big buffer objects feasible.
TTM uses a fine-grained per buffer-object locking scheme, taking
care to release all relevant locks when waiting for the GPU.
Although this implies some locking overhead, it's probably a big
win for devices with multiple command submission mechanisms, since
the lock contention will be minimal.
TTM can be used with whatever user-space interface the driver
chooses, including GEM. It's used by the upcoming Radeon KMS DRM driver
and is also the GPU memory management core of various new experimental
DRM drivers.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (50 commits)
drm: include kernel list header file in hashtab header
drm: Export hash table functionality.
drm: Split out the mm declarations in a separate header. Add atomic operations.
drm/radeon: add support for RV790.
drm/radeon: add rv740 drm support.
drm_calloc_large: check right size, check integer overflow, use GFP_ZERO
drm: Eliminate magic I2C frobbing when reading EDID
drm/i915: duplicate desired mode for use by fbcon.
drm/via: vfree() no need checking before calling it
drm: Replace DRM_DEBUG with DRM_DEBUG_DRIVER in i915 driver
drm: Replace DRM_DEBUG with DRM_DEBUG_MODE in drm_mode
drm/i915: Replace DRM_DEBUG with DRM_DEBUG_KMS in intel_sdvo
drm/i915: replace DRM_DEBUG with DRM_DEBUG_KMS in intel_lvds
drm: add separate drm debugging levels
radeon: remove _DRM_DRIVER from the preadded sarea map
drm: don't associate _DRM_DRIVER maps with a master
drm: simplify kcalloc() call to kzalloc().
intelfb: fix spelling of "CLOCK"
drm: fix LOCK_TEST_WITH_RETURN macro
drm/i915: Hook connector to encoder during load detection (fixes tv/vga detect)
...
this is a TTM preparation patch, it rearranges the mm and
add operations needed to do mm operations in atomic context.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previously we would check size instead of size * nmemb, and so would
never hit the vmalloc path. Also add integer overflow check as in kcalloc,
and allocate GFP_ZERO pages instead of memset()ing them.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now all the DRM debug info will be reported if the boot option of
"drm.debug=1" is added. Sometimes it is inconvenient to get the debug
info in KMS mode. We will get too much unrelated info.
This will separate several DRM debug levels and the debug level can be used
to print the different debug info. And the debug level is controlled by the
module parameter of drm.debug
In this patch it is divided into four debug levels;
drm_core, drm_driver, drm_kms, drm_mode.
At the same time we can get the different debug info by changing the debug
level. This can be done by adding the module parameter. Of course it can
be changed through the /sys/module/drm/parameters/debug after the system is
booted.
Four debug macro definitions are provided.
DRM_DEBUG(fmt, args...)
DRM_DEBUG_DRIVER(prefix, fmt, args...)
DRM_DEBUG_KMS(prefix, fmt, args...)
DRM_DEBUG_MODE(prefix, fmt, args...)
When the boot option of "drm.debug=4" is added, it will print the debug info
using DRM_DEBUG_KMS macro definition.
When the boot option of "drm.debug=6" is added, it will print the debug info
using DRM_DEBUG_KMS/DRM_DEBUG_DRIVER.
Sometimes we expect to print the value of an array.
For example: SDVO command,
In such case the following four DRM debug macro definitions are added:
DRM_LOG(fmt, args...)
DRM_LOG_DRIVER(fmt, args...)
DRM_LOG_KMS(fmt, args...)
DRM_LOG_MODE(fmt, args...)
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When this macro isn't called with 'file_priv' this will result in a build
failure.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Making the drm_crtc.c code recognize the DPMS property and invoke the
connector->dpms function doesn't remove any capability from the driver while
reducing code duplication.
That just highlighted the problem with the existing DPMS functions which
could turn off the connector, but failed to turn off any relevant crtcs. The
new drm_helper_connector_dpms function manages all of that, using the
drm_helper-specific crtc and encoder dpms functions, automatically computing
the appropriate DPMS level for each object in the system.
This fixes the current troubles in the i915 driver which left PLLs, pipes
and planes running while in DPMS_OFF mode or even while they were unused.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For awhile now, many of the GEM code paths have allocated page or
object arrays with the slab allocator. This is nice and fast, but
won't work well if memory is fragmented, since the slab allocator works
with physically contiguous memory (i.e. order > 2 allocations are
likely to fail fairly early after booting and doing some work).
This patch works around the issue by falling back to vmalloc for
>PAGE_SIZE allocations. This is ugly, but much less work than chaining
a bunch of pages together by hand (suprisingly there's not a bunch of
generic kernel helpers for this yet afaik). vmalloc space is somewhat
precious on 32 bit kernels, but our allocations shouldn't be big enough
to cause problems, though they're routinely more than a page.
Note that this patch doesn't address the unchecked
alloc-based-on-ioctl-args in GEM; that needs to be fixed in a separate
patch.
Also, I've deliberately ignored the DRM's "area" junk. I don't think
anyone actually uses it anymore and I'm hoping it gets ripped out soon.
[Updated: removed size arg to new free function. We could unify the
free functions as well once the DRM mem tracking is ripped out.]
fd.o bug #20152 (part 1/3)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This allows userlevel code to discover the pipe number corresponding
to a given CRTC ID. This is necessary for doing pipe-specific
operations such as waiting for vblank on a given CRTC. Failure to use
the right pipe mapping can result in GPU hangs, or at least failure
to actually sync to vblank.
Signed-off-by: Carl Worth <cworth@cworth.org>
[anholt: Style touchups from review]
Signed-off-by: Eric Anholt <eric@anholt.net>
This had been delayed for some time due to failure to work on the one piece
of G41 hardware we had, and lack of success reports from anybody else.
Current hardware appears to be OK.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
[anholt: hand-applied due to conflicts with IGD patches]
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: fix scheduling while holding the new active list spinlock
drm/i915: Allow tiling of objects with bit 17 swizzling by the CPU.
drm/i915: Correctly set the write flag for get_user_pages in pread.
drm/i915: Fix use of uninitialized var in 40a5f0de
drm/i915: indicate framebuffer restore key in SysRq help message
drm/i915: sync hdmi detection by hdmi identifier with 2D
drm/i915: Fix a mismerge of the IGD patch (new .find_pll hooks missed)
drm/i915: Implement batch and ring buffer dumping
Support the Intel 854 Chipset in fbdev.
We test and use the patch on a Thomson IP1101 IPTV-Box. On the VGA-Port
we get a normal signal.
Here is the link to the Mambux-Project: http://www.mambux.de
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Stefan Husemann <shusemann@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Save the bit 17 state of the pages when freeing the page list, and
reswizzle them if necessary when rebinding the pages (in case they were
swapped out). Since we have userland with expectations that the swizzle
enums let it pread and pwrite contents accurately, we can't expose a new
swizzle enum for bit 17 (which it would have to GTT map to handle), so we
handle it down in pread and pwrite by swizzling the copy when bit 17 of the
page address is set.
Signed-off-by: Eric Anholt <eric@anholt.net>
Remove an include that isn't actually needed to prevent needless
rebuilds.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The readq/writeq really need to be static inline on the arches which
don't provide them.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Sometime we need to communicate with HDMI monitor by sending audio or video
info frame, so we have to know monitor type. However if user utilize HDMI-DVI adapter to connect DVI monitor, hardware detection will incorrectly show the monitor is HDMI. HDMI spec tell us that any device containing IEEE registration Identifier will be treated as HDMI device. The patch intends to detect HDMI monitor by this rule.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
shrinks drm_ioctl_desc from 24 bytes to 16 bytes by reordering members
to remove padding.
updates DRM_IOCTL_DEF macro to initialise structure members by name to
handle the structure reorder.
The applied patch reduces data used in drm.ko from 10440 to 9032
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Usually drm read basic EDID, that is enough for us, but since igital display
were introduced i.e. HDMI monitor, sometime we need to interact with monitor by
EDID extension information,
EDID extensions include audio/video data block, speaker allocation and vendor specific data blocks.
This patch intends to read EDID extensions from digital monitor for users.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The old mechanism to formatting proc files is extremely ugly. The
seq_file API was designed specifically for cases like this and greatly
simplifies the process.
Also, most of the files in /proc really don't belong there. This patch
introduces the infrastructure for putting these into debugfs and exposes
all of the proc files in debugfs as well.
Signed-off-by: Ben Gamari <bgamari@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The drm headers are traditionally shared with BSD and
could not use the strict linux integer types. This is
over now, so we can use our own types now.
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The readq/writeq stuff is from Dave Miller, and he
warns users to be careful about using these. Plans are only
r600 to use it so far.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The old mechanism to formatting proc files is extremely ugly. The
seq_file API was designed specifically for cases like this and greatly
simplifies the process.
Also, most of the files in /proc really don't belong there. This patch
introduces the infrastructure for putting these into debugfs and exposes
all of the proc files in debugfs as well.
This contains the i915 hooks rewrite as well, to make bisectability better.
Signed-off-by: Ben Gamari <bgamari@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The kernel shouldn't be in the business of telling user space which
driver to load. The kernel defers mapping PCI IDs to module names
to user space and we should do the same for DRI drivers.
And in fact, that's how it does work today. Nothing uses the
dri_library_name attribute, and the attribute is in fact broken.
For intel devices, it falls back to the default behaviour of returning
the kernel module name as the DRI driver name, which doesn't work for
i965 devices. Nobody has ever hit this problem or filed a bug about this.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Under kernel modesetting, we manage the device at all times, regardless
of VT switching and X servers, so the only decent thing to do is to
claim the PCI device. In that case, we call the suspend/resume hooks
directly from the pci driver hooks instead of the current class device detour.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This changes drm_local_map to use a resource_size for its "offset"
member instead of an unsigned long, thus allowing 32-bit machines
with a >32-bit physical address space to be able to store there
their register or framebuffer addresses when those are above 4G,
such as when using a PCI video card on a recent AMCC 440 SoC.
This patch isn't as "trivial" as it sounds: A few functions needed
to have some unsigned long/int changed to resource_size_t and a few
printk's had to be adjusted.
But also, because userspace isn't capable of passing such offsets,
I had to modify drm_find_matching_map() to ignore the offset passed
in for maps of type _DRM_FRAMEBUFFER or _DRM_REGISTERS.
If we ever support multiple _DRM_FRAMEBUFFER or _DRM_REGISTERS maps
for a given device, we might have to change that trick, but I don't
think that happens on any current driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Once upon a time, the DRM made the distinction between the drm_map
data structure exchanged with user space and the drm_local_map used
in the kernel.
For some reasons, while the BSD port still has that "feature", the
linux part abused drm_map for kernel internal usage as the local
map only existed as a typedef of the struct drm_map.
This patch fixes it by declaring struct drm_local_map separately
(though its content is currently identical to the userspace variant),
and changing the kernel code to only use that, except when it's a
user<->kernel interface (ie. ioctl).
This allows subsequent changes to the in-kernel format
I've also replaced the use of drm_local_map_t with struct drm_local_map
in a couple of places. Mostly by accident but they are the same (the
former is a typedef of the later) and I have some remote plans and
half finished patch to completely kill the drm_local_map_t typedef
so I left those bits in.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The DRM uses its own wrappers to obtain resources from PCI devices,
which currently convert the resource_size_t into an unsigned long.
This is broken on 32-bit platforms with >32-bit physical address
space.
This fixes them, along with a few occurences of unsigned long used
to store such a resource in drivers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Comparing the layouts of struct detail_pixel_timing with
x.org's struct detailed_timings and how those are handled,
it appears that the hsync_positive and vsync_positive
fields are backwards.
This patch fixes https://bugs.freedesktop.org/show_bug.cgi?id=20019
for me. It was tested on 2 monitors, LG FLATRON L225WS 22" and
a YAKUMO 17" for which more details are unknown.
Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In some cases we may receive a mode config that has a different
CRTC<->encoder map that the current configuration. In that case, we
need to disable any re-routed encoders before setting the mode,
otherwise they may not pick up the new CRTC (if the output types are
incompatible for example).
Tested-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This fixes potential fault at fault time if the object was unreferenced
while the mapping still existed. Now, while the mmap_offset only lives
for the lifetime of the object, the object also stays alive while a vma
exists that needs it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check the error paths within intel_pipe_set_base() to first cleanup and
then report back the error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Avoids leaking fbs and associated buffers on release.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Tested-by: Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Adds code to set up fence registers at execbuf time on pre-965 chips as
necessary. Also fixes up a few bugs in the pre-965 tile register support
(get_order != ffs). The number of fences available to the kernel defaults
to the hw limit minus 3 (for legacy X front/back/depth), but a new parameter
allows userspace to override that as needed.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Schedule a vblank signal, kill the process, and we'll go walking over freed
memory. Given that no open-source userland exists using this, nor have I
ever heard of a consumer, just let this code die.
Signed-off-by: Eric Anholt <eric@anholt.net>
Requested-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Create a separate mode_config IDR lock for simplicity. The core DRM
config structures (connector, mode, etc. lists) are still protected by
the mode_config mutex, but the CRTC IDR (used for the various identifier
IDs) is now protected by the mode_config idr_mutex. Simplifies the
locking a bit and removes a warning.
All objects are protected by the config mutex, we may in the future,
split the object further to have reference counts.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When mode setting is first initialized, the driver will call into
drm_helper_initial_config() to set up an initial output and framebuffer
configuration. This routine is responsible for probing the available
connectors, encoders, and crtcs, looking for modes and putting together
something reasonable (where reasonable is defined as "allows kernel
messages to be visible on as many displays as possible").
However, the code was a bit too aggressive in setting default modes when
none were found on a given connector. Even if some connectors had modes,
any connectors found lacking modes would have the default 800x600 mode added
to their mode list, which in some cases could cause problems later down the
line. In my case, the LVDS was perfectly available, but the initial config
code added 800x600 modes to both of the detected but unavailable HDMI
connectors (which are on my non-existent docking station). This ended up
preventing later code from setting a mode on my LVDS, which is bad.
This patch fixes that behavior by making the initial config code walk
through the connectors first, counting the available modes, before it decides
to add any default modes to a possibly connected output. It also fixes the
logic in drm_target_preferred() that was causing zeroed out modes to be set
as the preferred mode for a given connector, even if no modes were available.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This removes the requirement for user space to pin a buffer before
setting a mode that is backed by the pixels from that buffer.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Painfully userspace started using new names that were never actually to be
used from the external repo.
Also fill out the gaps in the structure for old/new userspace compat
Add compat defines for these structs.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The replace fb ioctl replaces the backing buffer object for a modesetting
framebuffer object. This can be acheived by just creating a new
framebuffer backed by the new buffer object, setting that for the crtcs
in question and then removing the old framebuffer object.
Signed-off-by: Kristian Hogsberg <krh@redhat.com>
Acked-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The initially merged modesetting API has some uglies in it, this
cleans up the struct members and ioctl ordering for initial submission.
It also removes the unneeded hotplug infrastructure.
airlied:- I've pulled this patch in from git modesetting-gem tree.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit adds i915 driver support for the DRM mode setting APIs.
Currently, VGA, LVDS, SDVO DVI & VGA, TV and DVO LVDS outputs are
supported. HDMI, DisplayPort and additional SDVO output support will
follow.
Support for the mode setting code is controlled by the new 'modeset'
module option. A new config option, CONFIG_DRM_I915_KMS controls the
default behavior, and whether a PCI ID list is built into the module for
use by user level module utilities.
Note that if mode setting is enabled, user level drivers that access
display registers directly or that don't use the kernel graphics memory
manager will likely corrupt kernel graphics memory, disrupt output
configuration (possibly leading to hangs and/or blank displays), and
prevent panic/oops messages from appearing. So use caution when
enabling this code; be sure your user level code supports the new
interfaces.
A new SysRq key, 'g', provides emergency support for switching back to
the kernel's framebuffer console; which is useful for testing.
Co-authors: Dave Airlie <airlied@linux.ie>, Hong Liu <hong.liu@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add mode setting support to the DRM layer.
This is a fairly big chunk of work that allows DRM drivers to provide
full output control and configuration capabilities to userspace. It was
motivated by several factors:
- the fb layer's APIs aren't suited for anything but simple
configurations
- coordination between the fb layer, DRM layer, and various userspace
drivers is poor to non-existent (radeonfb excepted)
- user level mode setting drivers makes displaying panic & oops
messages more difficult
- suspend/resume of graphics state is possible in many more
configurations with kernel level support
This commit just adds the core DRM part of the mode setting APIs.
Driver specific commits using these new structure and APIs will follow.
Co-authors: Jesse Barnes <jbarnes@virtuousgeek.org>, Jakob Bornecrantz <jakob@tungstengraphics.com>
Contributors: Alan Hourihane <alanh@tungstengraphics.com>, Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use the new core GEM object mapping code to allow GTT mapping of GEM
objects on i915. The fault handler will make sure a fence register is
allocated too, if the object in question is tiled.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add core support for mapping of GEM objects. Drivers should provide a
vm_operations_struct if they want to support page faulting of objects.
The code for handling GEM object offsets was taken from TTM, which was
written by Thomas Hellström.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
...so drm_getunique() is trying to copy some uninitialized data to
userspace. The ECX register contains the number of words that are
left to copy -- so there are 5 * 4 = 20 bytes left. The offset of the
first uninitialized byte (counting from the start of the string) is
also 20 (i.e. 0xf65d2294&((1 << 5)-1) == 20). So somebody tried to
copy 40 bytes when the string was only 19 long.
In drm_set_busid() we have this code:
dev->unique_len = 40;
dev->unique = drm_alloc(dev->unique_len + 1, DRM_MEM_DRIVER);
...
len = snprintf(dev->unique, dev->unique_len, pci:%04x:%02x:%02x.%d",
...so it seems that dev->unique is never updated to reflect the
actual length of the string. The remaining bytes (20 in this case)
are random uninitialized bytes that are copied into userspace.
This patch fixes the problem by setting dev->unique_len after the
snprintf().
airlied- I've had to fix this up to store the alloced size so
we have it for drm_free later.
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Vegard Nossum <vegardno@thuin.ifi.uio.no>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is step one towards having multiple masters sharing a drm
device in order to get fast-user-switching to work.
It splits out the information associated with the drm master
into a separate kref counted structure, and allocates this when
a master opens the device node. It also allows the current master
to abdicate (say while VT switched), and a new master to take over
the hardware.
It moves the Intel and radeon drivers to using the sarea from
within the new master structures.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current sub-module unload exit path is a mess, it tries
to abuse the idr. Just keep a list of devices per driver struct
and free them in-order on rmmod.
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm vblank initialization keeps track of the changes in driver-supplied
frame counts across vt switch and mode setting, but only if you let it by
not tearing down the drm vblank structure.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes hangs on 855-class hardware by avoiding double attachment of the
driver due to the stub second head device having the same pci id as the real
device.
Other DRM drivers probably want this treatment as well, but I'm applying it
just to this one for safety. But we should clean up the drm_pciids.h mess
now so that each driver has its own pci id list header in its own directory.
Lets do that in the next release.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's not used in any other drivers, and doesn't look like it will be from
drm.git master.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This will let userland know when to submit its batchbuffers, before they get
too big to fit in the aperture.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Someone noticed these registers moved around for later chips,
so we redo the codepaths per-chip. PCIE chips don't appear to
require explicit enables.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This should improve performance by avoiding uncached reads by the CPU (the
point of having a status page), and may improve stability. This patch only
affects G33, GM45 and G45 chips as those are the only ones using GTT-based
HWS mappings.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Like the last patch but adds a macro to get at the irq value instead of
dereferencing pdev directly. Should make things easier for the BSD guys and
if we ever support non-PCI devices.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
GEM allows the creation of persistent buffer objects accessible by the
graphics device through new ioctls for managing execution of commands on the
device. The userland API is almost entirely driver-specific to ensure that
any driver building on this model can easily map the interface to individual
driver requirements.
GEM is used by the 2d driver for managing its internal state allocations and
will be used for pixmap storage to reduce memory consumption and enable
zero-copy GLX_EXT_texture_from_pixmap, and in the 3d driver is used to enable
GL_EXT_framebuffer_object and GL_ARB_pixel_buffer_object.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previously, drivers supporting vblank interrupt waits would run the interrupt
all the time, or all the time that any 3d client was running, preventing the
CPU from sleeping for long when the system was otherwise idle. Now, interrupts
are disabled any time that no client is waiting on a vblank event. The new
method uses vblank counters on the chipsets when the interrupts are turned
off, rather than counting interrupts, so that we can continue to present
accurate vblank numbers.
Co-author: Michel Dänzer <michel@tungstengraphics.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is no point in considering FreeBSD et al. in the linux kernel
source code.
Signed-off-by: Carlos R. Mafra <crmafra@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With new userspace libpciaccess we can get a conflicting mapping
on the PCIE GART table in the video RAM. Always try and map it _wc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
With the coming of kernel based modesetting and the memory manager stuff,
the everything in one directory approach was getting very ugly and
starting to be unmanageable.
This restructures the drm along the lines of other kernel components.
It creates a drivers/gpu/drm directory and moves the hw drivers into
subdirectores. It moves the includes into an include/drm, and
sets up the unifdef for the userspace headers we should be exporting.
Signed-off-by: Dave Airlie <airlied@redhat.com>
