ERROR: "foo* bar" should be "foo *bar"
ERROR: "foo * bar" should be "foo *bar"
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Also remove some blank lines that were used to split compat code at -devel
tree.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After adding support for AVerTVHD Volar, DVB_USB_CXUSB must
select MEDIA_TUNER_MXL5005S if !DVB_FE_CUSTOMISE
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add initial support for this device. The AGC and tracking filter
settings for the mxl5003 are known to be wrong, but it generally works.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Allow the following configuration, by passing clock_polarity_flip = 2:
Enable FEC automatic reset. Disable spectrum inversion.
Enable viterbi resynchronization. Set polarity indicator high.
Enable error flag insertion.
Thanks to Daniel Gimpelevich, for discovering that this configuration
is used on the AVerMedia AVerTVHD Volar.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
CC: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
As reported by Stephen Rothwell <sfr@canb.auug.org.au>:
drivers/media/dvb/ttpci/budget-ci.c:50:21: error: tda827x.h: No such file or directory
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
... but two ancient drivers had not noticed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
split the suckers into kernel-memory and user-memory versions,
annotate both properly.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
According to RFC 4326 (4.1) D-bit is MSB in net-endian 16bit.
dvb_net.c did
/* Set D-bit for CRC32 verification,
* if it was set originally. */
ulen |= 0x0080;
which works of little-endian (htons(1<<15) is 0x0080 there), but breaks
on big-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support the bundled remote control of the TT DVB-C 1501
Thanks-to: SG <SiestaGomez@web.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removed some obsolete definitions and one unused variable.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Auto-selects tda10023, for budget-ci, if !DVB_FE_CUSTOMISE. This is needed for
Technotrend budget C-1501 dvb board.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The following experimental patch adds support for the technotrend budget
C-1501 dvb-c card. The parameters used to configure the tda10023 demod
chip are largely determined experimentally, but works quite for me in my
initial tests.
Signed-off-by: Sigmund Augdal <sigmund@snap.tv>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- support for Anysee E30C Plus rev 0.4
- set IO port E
- set correct TS mode
- change deltaf according to latest Windows driver
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- update license comments
- change MODULE_DESCRIPTION from device specific to chipset specific
- correct debug switch from deb_rc to deb_info
- correct MPEG2 stream interval from 1.25 to 1
- change frontend_attach error code from -EIO to -ENODEV
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now that we have a specific lock to protect the network
device unicast and multicast lists, remove extraneous
grabs of the TX lock in cases where the code only needs
address list protection.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netif_addr_{lock,unlock}{,_bh}() helpers.
Use them to protect operations that operate on or read
the network device unicast and multicast address lists.
Also use them in cases where the code simply wants to
block calls into the driver's ->set_rx_mode() and
->set_multicast_list() methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-2.6.27' of git://git.infradead.org/users/dwmw2/firmware-2.6: (64 commits)
firmware: convert sb16_csp driver to use firmware loader exclusively
dsp56k: use request_firmware
edgeport-ti: use request_firmware()
edgeport: use request_firmware()
vicam: use request_firmware()
dabusb: use request_firmware()
cpia2: use request_firmware()
ip2: use request_firmware()
firmware: convert Ambassador ATM driver to request_firmware()
whiteheat: use request_firmware()
ti_usb_3410_5052: use request_firmware()
emi62: use request_firmware()
emi26: use request_firmware()
keyspan_pda: use request_firmware()
keyspan: use request_firmware()
ttusb-budget: use request_firmware()
kaweth: use request_firmware()
smctr: use request_firmware()
firmware: convert ymfpci driver to use firmware loader exclusively
firmware: convert maestro3 driver to use firmware loader exclusively
...
Fix up trivial conflicts with BKL removal in drivers/char/dsp56k.c and
drivers/char/ip2/ip2main.c manually.
...which means allocating our own copy when we want to modify it.
(stupid thinko fixed by mkrufky)
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
This decreases scan time in Queens, New York from 28 minutes to 7 minutes,
with the exact same services found.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix uncorrected block counter and bit error rate to follow DVB API spec:
- Unsupported controls return -ENOSYS.
- UNC must never be set to 0.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the i2c write fails during initialisation, an oops happens
because state->frontend.dvb is still undefined. Fixed.
Thanks to Sigmund Augdal for reporting this bug,
and to Hartmut Birr for suggesting the fix.
Thanks-to: Sigmund Augdal <sigmund@snap.tv>
Thanks-to: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the current modulation and frequency is already set to
the desired parameters, then don't re-tune.
Don't store current frequency until after we've tuned successfully.
Force a re-tune after resume from standby.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In the umt-010 driver the struct umt_properties sets the number of URBs for
transfer to 20. But in dvb-usb.h MAX_NO_URBS_FOR_DATA_STREAM is set to 10.
Not surprisingly this causes an oops for all devices which use the umt-010
chipset when they are inserted.
fix on Kaffeine channel scan for
Initialize stream count using MAX_NO_URBS_FOR_DATA_STREAM.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When an error occurs at firmware loading, sometimes, tda1004x stops answering.
Instead of reporting such error, attach code were assuming that the device were
answering an invalid ID (0xff). This can be seen when enabling debug options:
tda1004x: tda1004x_read_byte: reg=0x0
tda1004x: tda1004x_read_byte: error reg=0x0, ret=-5
Now, instead of reporting an invalid ID, it will report the correct error:
tda10046: chip is not answering. Giving up.
saa7133[0]/dvb: failed to attach tda10046
saa7133[0]/dvb: frontend initialization failed
A possible improvement would be trying to reset the device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A fresh copy of v.29 firmware, using get_firmware, is leading to an invalid
firmware:
DVB: registering new adapter (saa7133[0])
DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
tda1004x: setting up plls for 48MHz sampling clock
tda1004x: found firmware revision ff -- invalid
tda1004x: trying to boot from eeprom
tda1004x: found firmware revision ff -- invalid
tda1004x: waiting for firmware upload...
tda1004x: Error during firmware upload
tda1004x: found firmware revision ff -- invalid
tda1004x: firmware upload failed
Sometimes, loading/unloading this firmware makes tda1004x to return an invalid
ID. However, there were no printk messages to help to identify what were the
cause for the error.
With this patch, it will now print:
Invalid tda1004x ID = 0xff. Can't proceed
saa7133[0]/dvb: failed to attach tda10046
saa7133[0]/dvb: frontend initialization failed
Tested with LifeView FlyDVB-T Hybrid Cardbus/MSI TV @nywhere A/D NB
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
direct dereferencing from user-supplied address
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Endianness annotations and fixes + fixing the handling of
->uncorrected_block_count
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
somebody forgot to to fix this header...
Thanks to Ingo Molnar for pointing this out.
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
testing of the -tip tree found the following build failures on
2.6.26-rc3:
drivers/built-in.o: In function `ttusb_dec_disconnect':
ttusb_dec.c:(.text+0xa2c95): undefined reference to `input_unregister_device'
drivers/built-in.o: In function `dvb_usb_read_remote_control':
dvb-usb-remote.c:(.text+0xa6a94): undefined reference to `input_event'
with this config:
http://redhat.com/~mingo/misc/config-Tue_May_20_03_48_57_CEST_2008.bad
these are due to the media/dvb/usb layer having dependencies on INPUT
functionality, without having that spelled out in the Kconfig file.
this patch makes that dependency explicit (for the drivers affected),
which solves the build error.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch does some small cleanup to mt312.
It changes kconfig description to also list the ZL10313.
It does change some strange symbol names to be consistent with
module name mt312 and naming of all other functions in there.
* vp310_mt312_ops -> mt312_ops
* vp310_mt312_attach -> mt312_attach
Adds a MODULE_AUTHOR for me
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
itd1000_fre_values[] can become static const.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since:
1) FW_LOADER is defined as:
config FW_LOADER
tristate "Userspace firmware loading support"
depends on HOTPLUG
2) several V4L/DVB driver just selects it;
3) select is not smart enough to auto-select HOTPLUG, if select FW_LOADER.
So, All drivers that select FW_LOADER should also depend on HOTPLUG.
An easier solution (for the end-user perspective) would be to "select HOTPLUG".
However, live is not simple. This would cause recursive dependency issues like
this one:
drivers/usb/Kconfig:62:error: found recursive dependency: USB -> USB_OHCI_HCD
-> I2C -> MEDIA_TUNER -> MEDIA_TUNER_XC2028 -> HOTPLUG -> PCCARD -> PCMCIA ->
USB_ARCH_HAS_HCD -> MOUSE_APPLETOUCH -> USB
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
x86.git testing found the following build bug in v2.6.26-rc1:
drivers/built-in.o: In function `cinergyt2_probe':
cinergyT2.c:(.text+0xb6117): undefined reference to `input_allocate_device'
cinergyT2.c:(.text+0xb6230): undefined reference to `input_register_device'
cinergyT2.c:(.text+0xb623d): undefined reference to `input_free_device'
with the following config:
http://redhat.com/~mingo/misc/config-Sun_May__4_22_06_54_CEST_2008.bad
The reason for the bug is that the cinergyT2 driver depends on
CONFIG_INPUT functionality, but if INPUT is modular it's still possible
to build CONFIG_DVB_CINERGYT2=y - which leads to missing symbols.
The solution is to make DVB_CINERGYT2 dependent on INPUT.
[ This solves the build problem - i have not tested the driver on this card. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This change addresses kernel bug #10459: In kernel 2.6.25 the
budget_av driver polls for an CI slot in 100ms intervals (because no
interrupt solution for budget_av cards is feasible due to HW reasons).
If no CI/CAM is connected to the DVB card, polling times out only after 250ms.
This periodic polling leads to high CPU load.
The change increases the polling interval for empty slots from 100ms to 5s.
Intervals for remaining slot states (invalid, in progress, ready) are unchanged,
as they are either temporary conditions or no timeout should occur.
Signed-off-by: Robert Schedel <r.schedel@yahoo.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/dvb/frontends/s5h1420.c: In function `s5h1420_setsymbolrate':
drivers/media/dvb/frontends/s5h1420.c:484: warning: long long unsigned int format, u64 arg (arg 2)
We do not know what type the architecture uses for u64.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Those tuners are currently used only under media/dvb. However,
they can support also analog TV. Better to move them to the same place
as the other hybrid tuners. This would make easier to use those tuners also
by analog drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are some DVB-S tuners together with DVB-S tags, while
others together with tuners. Better to have all of them together.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There were several issues in the past, caused by the hybrid tuner design, since
now, the same tuner can be used by drivers/media/dvb and drivers/media/video.
Kconfig items were rearranged, to split V4L/DVB core from their drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds full support for this demodulator.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Make it unsigned (0/1) rather than signed (0/-1).
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
