Used bootloder address from FLT while loading FW from flash as well.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In case of both target and initiator capabilities reported by fc port,
the fc port port capability is made mutualy exclusive with priority given
for target capabilities.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* hold the hardware_lock throughout the duration of ctx-sp
timeout handling -- could result in use-after-free oops.
* retry a timed-out login-request.
* done() routines are called with the hardware-lock held, issue
qla2x00_mark_device_lost() with proper 'defer' flag.
* FCP2 capabilities are only relevant to target devices.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Hold a reference to the srb (sp) while aborting an I/O -- as the
I/O can/will complete from within the interrupt-context.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The TMFs used for pre-24xx ISPs incorrectly assumed 'cpu' tag
data could be valid. These chips have no multi-q/cpu-affinity
support. This corrects an oops seen on ISP23xx parts.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This helps to correlate submission/completion messages during
triaging.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The CRB drive active register is cleared when driver is unloaded
or when driver enters failed state.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We have 32 (MAXSGENTRIES) scatter gather elements embedded
in the command. With all these, the total command size is
about 576 bytes. However, the last entry in the block fetch table
is 35. (the block fetch table contains the number of 16-byte chunks
the firmware needs to fetch for a given number of scatter gather
elements.) 35 * 16 = 560 bytes, which isn't enough. It needs to be
36. (36 * 16 == 576) or, MAXSGENTRIES + 4. (plus 4 because there's a
bunch of stuff at the front of the command before the first scatter
gather element that takes up 4 * 16 bytes.) Without this fix, the
controller may have to perform two DMA operations to fetch the
command since the first one may not get the whole thing.
Signed-off-by: Don Brace <brace@beardog.cce.hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
before trying to enter simple mode transport method.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The end of the function is reachable both when host is and is not NULL.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E,E1;
identifier f;
statement S1,S2,S3;
@@
if ((E == NULL && ...) || ...)
{
... when != if (...) S1 else S2
when != E = E1
* E->f
... when any
return ...;
}
else S3
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adding DIF Type 2 protection support, as well as turning on 32 byte cdb's,
and setting the cdb length for > 16 byte in the SCSI_IO->control parameter.
Signed-off-by: Martin Petersen <martin.petersen@oracle.com>
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
A driver needs to be ready to take an interrupt as soon as it registers
an interrupt handler. I noticed the following oops when testing kdump:
ipr: IBM Power RAID SCSI Device Driver version: 2.5.0 (February 11, 2010)
ibmvscsi 30000002: SRP_VERSION: 16.a
ibmvscsi 30000002: SRP_VERSION: 16.a
Unable to handle kernel paging request for data at address 0x00000000
...
pc: c000000004085e34: .tasklet_action+0xf4/0x1dc
...
c000000004086fe4 .__do_softirq+0x16c/0x2c0
c00000000403138c .call_do_softirq+0x14/0x24
c00000000400ee14 .do_softirq+0xa0/0x104
c00000000408690c .irq_exit+0x70/0xd0
c00000000400f190 .do_IRQ+0x214/0x2a8
c000000004004804 hardware_interrupt_entry+0x1c/0x98
--- Exception: 501 (Hardware Interrupt) at c00000000400c544 .raw_local_irq_restore+0x48/0x54
c00000000465d2a8 ._raw_spin_unlock_irqrestore+0x74/0xa0
c0000000040e7f00 .__setup_irq+0x2ec/0x3f0
c0000000040e8198 .request_threaded_irq+0x194/0x22c
c00000000446d854 .rpavscsi_init_crq_queue+0x284/0x3f0
c00000000446c764 .ibmvscsi_probe+0x688/0x710
c00000000402903c .vio_bus_probe+0x37c/0x3e4
c000000004403f10 .driver_probe_device+0xec/0x1b8
c000000004404088 .__driver_attach+0xac/0xf4
c000000004403184 .bus_for_each_dev+0x98/0x104
c000000004403c98 .driver_attach+0x40/0x60
c0000000044026f0 .bus_add_driver+0x154/0x324
c0000000044045d0 .driver_register+0xe8/0x1ac
c00000000402b2a8 .vio_register_driver+0x54/0x74
c000000004933ea4 .ibmvscsi_module_init+0x80/0xc0
c000000004009834 .do_one_initcall+0x98/0x1d8
c0000000049005b4 .kernel_init+0x27c/0x33c
c000000004031550 .kernel_thread+0x54/0x70
srp_task needs to be setup before request_irq. The patch below fixes the oops.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
It was possible to overflow the buffer used to print out the formatted
version of the resource path. The fix is to limit the number of
bytes that get formatted.
This patch also updates the ipr_show_resource_path function to display the
resource address for devices that are attached to adapters that don't
support resource paths.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: implement on-demand HPA unlocking
libata: use the enlarged capacity after late HPA unlock
SCSI: implement sd_unlock_native_capacity()
libata-sff: trivial corrections to Kconfig help text
sata_nv: don't diddle with nIEN on mcp55
sata_via: magic vt6421 fix for transmission problems w/ WD drives
Implement sd_unlock_native_capacity() method which calls into
hostt->unlock_native_capacity() if implemented. This will be invoked
by block layer if partitions extend beyond the end of the device and
can be used to implement, for example, on-demand ATA host protected
area unlocking.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Grant patches added an of mach table to struct device_driver. However,
while he changed the macio device code to use that, he left the match
table pointer in struct macio_driver and didn't update drivers to use
the "new" one, thus breaking the probing.
This completes the change by moving all drivers to setup the "new"
one, removing all traces of the old one, and while at it (since it
changes the exact same locations), I also remove two other duplicates
from struct driver which are the name and owner fields.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] fix race in scsi_target_reap
[SCSI] aacraid: Eliminate use after free
[SCSI] arcmsr: Support HW reset for EH and polling scheme for scsi device
[SCSI] bfa: fix system crash when reading sysfs fc_host statistics
[SCSI] iscsi_tcp: remove sk_sleep check
[SCSI] ipr: improve interrupt service routine performance
[SCSI] ipr: set the data list length in the request control block
[SCSI] ipr: fix a register read to use the correct address for 64 bit adapters
[SCSI] ipr: include the resource path in the IOA status area structure
[SCSI] ipr: implement fixes for 64 bit adapter support
[SCSI] be2iscsi: correct return value in mgmt_invalidate_icds()
st_open() suggests that llseek() doesn't work: "We really want to do
nonseekable_open(inode, filp); here, but some versions of tar incorrectly
call lseek on tapes and bail out if that fails. So we disallow pread()
and pwrite(), but permit lseeks."
Instead of using the fallback default_llseek() the driver should use
noop_llseek() which leaves the file->f_pos untouched but succeeds.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Kai Makisara <Kai.Makisara@kolumbus.fi>
Cc: Willem Riede <osst@riede.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__os_scsi_tape_open() suggests that llseek() doesn't work: "We really want
to do nonseekable_open(inode, filp); here, but some versions of tar
incorrectly call lseek on tapes and bail out if that fails. So we
disallow pread() and pwrite(), but permit lseeks."
Instead of using the fallback default_llseek() the driver should use
noop_llseek() which leaves the file->f_pos untouched but succeeds.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Willem Riede <osst@riede.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
osst_read()/osst_write() modify file->f_pos directly instead of the ppos
given to them. The VFS later updates the file->f_pos and overwrites it
with the value of ppos.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Willem Riede <osst@riede.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kill the obsolete HOSTS_C define and the related double inclusion of mvme147.h
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This patch (as1357) fixes a race in SCSI target allocation and
release. Putting a target in the STARGET_DEL state isn't protected by
the host lock, so an old target structure could be reused by a new
device even though it's about to be deleted. The cure is to change
the state while still holding the host lock.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The debugging code using the freed structure is moved before the kfree.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@free@
expression E;
position p;
@@
kfree@p(E)
@@
expression free.E, subE<=free.E, E1;
position free.p;
@@
kfree@p(E)
...
(
subE = E1
|
* E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
1. To support instantaneous report for SCSI device existing by periodic
polling
2. In arcmsr_iop_xfer(), inform AP of F/W's deadlock state to prevent
endless waiting
3. To block the coming SCSI command while the driver is handling bus reset
4. To support HW reset in bus reset error handler
Signed-off-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- C99 knows about USHRT_MAX/SHRT_MAX/SHRT_MIN, not
USHORT_MAX/SHORT_MAX/SHORT_MIN.
- Make SHRT_MIN of type s16, not int, for consistency.
[akpm@linux-foundation.org: fix drivers/dma/timb_dma.c]
[akpm@linux-foundation.org: fix security/keys/keyring.c]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The port data structure related to fc_host statistics collection is
not initialized. This causes system crash when reading the fc_host
statistics. The fix is to initialize port structure during driver
attach.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There is no need to call sk_sleep before calling wake_up_interruptible,
because the wait_queue_head is now with the socket.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
During performance testing on P7 machines it was observed that the interrupt
service routine was doing unnecessary MMIO operations.
This patch rearranges the logic of the routine and moves some of the code out
of the main routine. The result is that there are now fewer MMIO operations in
the performance path of the code.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In bring up testing for the new 64 bit adapters, the first read command failed
after loading the driver. The cause was that the command requires more than
one scatter gather element and the corresponding code to set the data list
length in the request control block was missing. This patch adds the correct
assignment.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix ipr_reset_enable_ioa() to read the correct IOA to host interrupt register
address for 64 bit adapters. We need to read the lower 32 bits, not the upper
32 bits.
Also change the write of the 64 bit mask value to a single writeq instead
of two writel calls.
Finally, use the correct u8 type for the type field in the ipr_resource_entry
structure.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The IOA status area now includes the new resource path field for 64 bit
adapters. This patch changes the driver to fix the ioasa structure and to use
the correct structure definition based on the type of adatper.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Implement some small fixes for 64 bit support that were preventing
the adapter from becoming operational.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This function should return 0 on error. Returning -1 would cause a
crash.
Also there is an extra space before the newline character and a missing
space between the "for" and the "mgmt_invalidate_icds". I put the string
on one line. The current version of checkpatch.pl complains that the
line is too long, but it makes grepping easier.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'bkl/ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/random-tracing:
uml: Pushdown the bkl from harddog_kern ioctl
sunrpc: Pushdown the bkl from sunrpc cache ioctl
sunrpc: Pushdown the bkl from ioctl
autofs4: Pushdown the bkl from ioctl
uml: Convert to unlocked_ioctls to remove implicit BKL
ncpfs: BKL ioctl pushdown
coda: Clean-up whitespace problems in pioctl.c
coda: BKL ioctl pushdown
drivers: Push down BKL into various drivers
isdn: Push down BKL into ioctl functions
scsi: Push down BKL into ioctl functions
dvb: Push down BKL into ioctl functions
smbfs: Push down BKL into ioctl function
coda/psdev: Remove BKL from ioctl function
um/mmapper: Remove BKL usage
sn_hwperf: Kill BKL usage
hfsplus: Push down BKL into ioctl function
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6:
of: change of_match_device to work with struct device
of: Remove duplicate fields from of_platform_driver
drivercore: Add of_match_table to the common device drivers
arch/microblaze: Move dma_mask from of_device into pdev_archdata
arch/powerpc: Move dma_mask from of_device into pdev_archdata
of: eliminate of_device->node and dev_archdata->{of,prom}_node
of: Always use 'struct device.of_node' to get device node pointer.
i2c/of: Allow device node to be passed via i2c_board_info
driver-core: Add device node pointer to struct device
of: protect contents of of_platform.h and of_device.h
of/flattree: Make unflatten_device_tree() safe to call from any arch
of/flattree: make of_fdt.h safe to unconditionally include.
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (38 commits)
net: Expose all network devices in a namespaces in sysfs
hotplug: netns aware uevent_helper
kobj: Send hotplug events in the proper namespace.
netlink: Implment netlink_broadcast_filtered
net/sysfs: Fix the bitrot in network device kobject namespace support
netns: Teach network device kobjects which namespace they are in.
kobject: Send hotplug events in all network namespaces
driver-core: fix Typo in drivers/base/core.c for CONFIG_MODULE
pci: check caps from sysfs file open to read device dependent config space
sysfs: add struct file* to bin_attr callbacks
sysfs: Remove usage of S_BIAS to avoid merge conflict with the vfs tree
sysfs: Don't use enums in inline function declaration.
sysfs-namespaces: add a high-level Documentation file
sysfs: Comment sysfs directory tagging logic
driver core: Implement ns directory support for device classes.
sysfs: Implement sysfs_delete_link
sysfs: Add support for tagged directories with untagged members.
sysfs: Implement sysfs tagged directory support.
kobj: Add basic infrastructure for dealing with namespaces.
sysfs: Remove double free sysfs_get_sb
...
The removal of the 'waitqueue_active()' test in commit d7d05548a6
("[SCSI] iscsi_tcp: fix relogin/shutdown hang") got incorrectly resolved
by David when he back-merged the main git tree into the networking tree
in commit 278554bd65 ("Merge branch 'master' of master.kernel.org:...").
There was a content conflict due to 'sock->sk->sk_sleep' being changed
into 'sk_sleep(sock->sk)' in the networking tree, but David didn't pick
up the iscsi change from the main tree.
Reported-by: James Bottomley <James.Bottomley@suse.de>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (182 commits)
[SCSI] aacraid: add an ifdef'd device delete case instead of taking the device offline
[SCSI] aacraid: prohibit access to array container space
[SCSI] aacraid: add support for handling ATA pass-through commands.
[SCSI] aacraid: expose physical devices for models with newer firmware
[SCSI] aacraid: respond automatically to volumes added by config tool
[SCSI] fcoe: fix fcoe module ref counting
[SCSI] libfcoe: FIP Keep-Alive messages for VPorts are sent with incorrect port_id and wwn
[SCSI] libfcoe: Fix incorrect MAC address clearing
[SCSI] fcoe: fix a circular locking issue with rtnl and sysfs mutex
[SCSI] libfc: Move the port_id into lport
[SCSI] fcoe: move link speed checking into its own routine
[SCSI] libfc: Remove extra pointer check
[SCSI] libfc: Remove unused fc_get_host_port_type
[SCSI] fcoe: fixes wrong error exit in fcoe_create
[SCSI] libfc: set seq_id for incoming sequence
[SCSI] qla2xxx: Updates to ISP82xx support.
[SCSI] qla2xxx: Optionally disable target reset.
[SCSI] qla2xxx: ensure flash operation and host reset via sg_reset are mutually exclusive
[SCSI] qla2xxx: Silence bogus warning by gcc for wrap and did.
[SCSI] qla2xxx: T10 DIF support added.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (49 commits)
libata-sff: separate out BMDMA qc_issue
libata-sff: prd is BMDMA specific
libata-sff: ata_sff_[dumb_]qc_prep are BMDMA specific
libata-sff: separate out BMDMA EH
libata-sff: port_task is SFF specific
libata-sff: ap->[last_]ctl are SFF specific
libata-sff: rename ap->ops->drain_fifo() to sff_drain_fifo()
libata-sff: introduce ata_sff_init/exit() and ata_sff_port_init()
libata-sff: clean up BMDMA initialization
libata-sff: clean up inheritance in several drivers
libata-sff: reorder SFF/BMDMA functions
sata_inic162x: kill PORT_PRD_ADDR initialization
libata: kill ATA_FLAG_DISABLED
libata-sff: kill unused prototype and make ata_dev_select() static
libata-sff: update bmdma host bus error handling
sata_mv: remove unnecessary initialization
sata_inic162x: inic162x is not dependent on CONFIG_ATA_SFF
pata_sch: use ata_pci_sff_init_one()
pata_sil680: Do our own exec_command posting
libata: Remove excess delay in the tf_load path
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
ATA_FLAG_DISABLED is only used by drivers which don't use
->error_handler framework and is largely broken. Its only meaningful
function is to make irq handlers skip processing if the flag is set,
which is largely useless and even harmful as it makes those ports more
likely to cause IRQ storms.
Kill ATA_FLAG_DISABLED and makes the callers disable attached devices
instead. ata_port_probe() and ata_port_disable() which manipulate the
flag are also killed.
This simplifies condition check in IRQ handlers. While updating IRQ
handlers, remove ap NULL check as libata guarantees consecutive port
allocation (unoccupied ports are initialized with dummies) and
long-obsolete ATA_QCFLAG_ACTIVE check (checked by ata_qc_from_tag()).
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Problem description:
--------------------
The problem reported by one of the customer was when a logical array
is deleted(from the SDK, from the GUI, from arcconf) then the
corresponding physical device (/dev/sdb, for example) is not removed
from the Linux namespace. So you end up with a "dead" device
entry. And some of the linux tools go slightly wonky.
Solution:
---------
Based on the notification from FW, the driver calls
"scsi_remove_device" for the DELETED drive. This call not only informs
the scsi device status to the SCSI mid layer and also it will remove
corresponding scsi device entries from the Linux sysfs.
Signed-off-by: Mahesh Rajashekhara <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Problem description:
--------------------
The issue reported by one of the customer was able to read LBA beyond
the array reported size with "sg_read" utility. If N is the last block
address reported, then should not be able to read past N,
i.e. N+1. But in their case, reported last LBA=143134719. So should
not have been able to read with LBA=143134720, but it is read without
failure, which means reported size to the OS is not correct and is
less than the actual last block address.
Solution:
---------
Firmware layer exposes lesser container capacity than the actual
one. It exposes [Actual size - Spitfire space(10MB)] to the OS, IO's
to the 10MB should be prohibited from the Linux driver. Driver checks
LBA boundary, if its greater than the array reported size then sets
sensekey to HARDWARE_ERROR and sends the notification to the MID
layer.
Signed-off-by: Mahesh Rajashekhara <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There are two conditions for ATA pass thru command that falls into
'SRB_STATUS_ERROR' condition.
1. When the "CC" bit is set by the host in ATA pass-through CDB
- Even for the successful completion, SCSI target shall generate
check condition.
- Driver returns a result code of SAM_STAT_CHECK_CONDITION, with a
driver byte of DID_OK to the mid layer.
Below is the snippet of existing code which fills a result code
of SAM_STAT_CHECK_CONDITION:
***********************************
if (le32_to_cpu(srbreply->scsi_status) == SAM_STAT_CHECK_CONDITION) {
int len;
scsicmd->result |= SAM_STAT_CHECK_CONDITION;
..........
************************************
2. When the "CC" bit is reset by the host and if SCSI target generates
a check condition when an error occurs.
- Driver returns a result code of SAM_STAT_CHECK_CONDITION, with a
driver byte of DID_ERROR to the mid layer.
Signed-off-by: Mahesh Rajashekhara <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The default driver setting is "expose_physicals=0", which means raw
physical drives are not exposed to OS. If the user wants to expose
connected physical drives, enable "expose_physicals" module parameter.
With the new JBOD firmware, physical drives are not available for
"expose_physicals>0". In function "aac_expose_phy_device", modified
to reset the appropriate bit in the first byte of inquiry data. This
fix exposes the connected physical drives.
Signed-off-by: Mahesh Rajashekhara <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Problem description:
--------------------
When the JBOD is created from the OS using Adaptec Storage Manager
utility device is not available under FDISK until a system restart is
done.
Solution:
---------
AIF handling: If there is a JBOD drive added to the system, identify
the old one with scsi_device_lookup() and remove it to enable a fresh
scsi_add_device(); else the new JBOD is not available until reboot.
Signed-off-by: Mahesh Rajashekhara <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently fcoe module ref count is used for tracking
active fcoe instances, it means each fcoe instance create
increments the count while destroy dec the count.
The dec is done only if fcoe instance is destroyed from
/sysfs but not if destroyed due to NETDEV_UNREGISTER event.
So this patch moves only module_put doing dec to common
fcoe_if_destroy function, so that dec would occur on ever
fcoe instance destroy.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
All VNports are sending FIP Keep-Alive messages with port_id and wwpn of the parent host instead of it's own port_id and wwpn. Standard FIP descriptor type 11 indicates to send own port_id and port_name.
Signed-off-by: Kaladhar Musunuru <kmusunuru@juniper.net>
Acked-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix typo in memset. Incorrect length parameter to memset resulting non-zero MAC address in FPMA messages.
Signed-off-by: Kaladhar Musunuru <kmusunuru@juniper.net>
Acked-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently rtnl mutex is grabbed during fcoe create, destroy, enable
and disable operations while sysfs s_active read mutex is already
held, but simultaneously other networking events could try grabbing
write s_active mutex while rtnl is already held and that is causing
circular lock warning, its detailed log pasted at end.
In this log, the rtnl was held before write s_active during device
renaming but there are more such cases as Joe reported another
instance with tg3 open at:-
http://www.open-fcoe.org/pipermail/devel/2010-February/008263.html
This patch fixes this issue by not waiting for rtnl mutex during
fcoe ops, that means if rtnl mutex is not immediately available
then restart_syscall() to allow others waiting in line to
grab s_active along with rtnl mutex to finish their work first
under these mutex.
Currently rtnl mutex was grabbed twice during fcoe_destroy call flow,
second grab was from fcoe_if_destroy called from fcoe_destroy after
dropping rtnl mutex before calling fcoe_if_destroy, so instead made
fcoe_if_destroy always called with rtnl mutex held to have this mutex
grabbed only once in this code path.
However left matching rtnl_unlock as-is in its original place as it was
dropped there for good reason since very next call causes synchronous
fip worker flush and if rtnl mutex is still held before flush
then that would cause new circular warning between fip->recv_work and
rtnl mutex, I've added detailed comment for this on fcoe_if_destroy
calling and rtnl muxtes unlocking.
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.33.1linux-stable-2.6.33 #1
-------------------------------------------------------
fcoemon/18823 is trying to acquire lock:
(fcoe_config_mutex){+.+.+.}, at: [<ffffffffa02ba5fc>] fcoe_create+0x27/0x4f7
[fcoe]
but task is already holding lock:
(s_active){++++.+}, at: [<ffffffff8115ef93>] sysfs_get_active_two+0x31/0x48
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (s_active){++++.+}:
[<ffffffff81077bdb>] __lock_acquire+0xb73/0xd2b
[<ffffffff81077e60>] lock_acquire+0xcd/0xf1
[<ffffffff8115e5df>] sysfs_deactivate+0x8b/0xe0
[<ffffffff8115edfb>] sysfs_addrm_finish+0x36/0x55
[<ffffffff8115d0cc>] sysfs_hash_and_remove+0x53/0x6a
[<ffffffff8115f353>] sysfs_remove_link+0x21/0x23
[<ffffffff812b6c93>] device_rename+0x99/0xcb
[<ffffffff8138dbf0>] dev_change_name+0xd5/0x1d2
[<ffffffff8138deee>] dev_ifsioc+0x201/0x2ac
[<ffffffff8138e4ba>] dev_ioctl+0x521/0x632
[<ffffffff81379e43>] sock_do_ioctl+0x3d/0x47
[<ffffffff8137a254>] sock_ioctl+0x213/0x222
[<ffffffff81114614>] vfs_ioctl+0x32/0xa6
[<ffffffff81114b94>] do_vfs_ioctl+0x490/0x4d6
[<ffffffff81114c30>] sys_ioctl+0x56/0x79
[<ffffffff81009b42>] system_call_fastpath+0x16/0x1b
-> #1 (rtnl_mutex){+.+.+.}:
[<ffffffff81077bdb>] __lock_acquire+0xb73/0xd2b
[<ffffffff81077e60>] lock_acquire+0xcd/0xf1
[<ffffffff8142f343>] __mutex_lock_common+0x4b/0x383
[<ffffffff8142f73f>] mutex_lock_nested+0x3e/0x43
[<ffffffff813959f9>] rtnl_lock+0x17/0x19
[<ffffffff8138ccae>] register_netdevice_notifier+0x1e/0x19b
[<ffffffffa02580c1>] 0xffffffffa02580c1
[<ffffffff81002069>] do_one_initcall+0x5e/0x15e
[<ffffffff81084094>] sys_init_module+0xd8/0x23a
[<ffffffff81009b42>] system_call_fastpath+0x16/0x1b
-> #0 (fcoe_config_mutex){+.+.+.}:
[<ffffffff81077a85>] __lock_acquire+0xa1d/0xd2b
[<ffffffff81077e60>] lock_acquire+0xcd/0xf1
[<ffffffff8142f343>] __mutex_lock_common+0x4b/0x383
[<ffffffff8142f73f>] mutex_lock_nested+0x3e/0x43
[<ffffffffa02ba5fc>] fcoe_create+0x27/0x4f7 [fcoe]
[<ffffffff810635b1>] param_attr_store+0x27/0x35
[<ffffffff81063619>] module_attr_store+0x26/0x2a
[<ffffffff8115dae3>] sysfs_write_file+0x108/0x144
[<ffffffff81107bd1>] vfs_write+0xae/0x10b
[<ffffffff81107cee>] sys_write+0x4a/0x6e
[<ffffffff81009b42>] system_call_fastpath+0x16/0x1b
other info that might help us debug this:
3 locks held by fcoemon/18823:
#0: (&buffer->mutex){+.+.+.}, at: [<ffffffff8115da17>]
sysfs_write_file+0x3c/0x144
#1: (s_active){++++.+}, at: [<ffffffff8115ef86>]
sysfs_get_active_two+0x24/0x48
#2: (s_active){++++.+}, at: [<ffffffff8115ef93>]
sysfs_get_active_two+0x31/0x48
stack backtrace:
Pid: 18823, comm: fcoemon Tainted: G W 2.6.33.1linux-stable-2.6.33 #1
Call Trace:
[<ffffffff81076c38>] print_circular_bug+0xa8/0xb6
[<ffffffff81077a85>] __lock_acquire+0xa1d/0xd2b
[<ffffffffa02ba5fc>] ? fcoe_create+0x27/0x4f7 [fcoe]
[<ffffffff81077e60>] lock_acquire+0xcd/0xf1
[<ffffffffa02ba5fc>] ? fcoe_create+0x27/0x4f7 [fcoe]
[<ffffffffa02ba5fc>] ? fcoe_create+0x27/0x4f7 [fcoe]
[<ffffffff8142f343>] __mutex_lock_common+0x4b/0x383
[<ffffffffa02ba5fc>] ? fcoe_create+0x27/0x4f7 [fcoe]
[<ffffffff8106ac70>] ? cpu_clock+0x43/0x5e
[<ffffffff81074e12>] ? lockstat_clock+0x11/0x13
[<ffffffff81074e40>] ? lock_release_holdtime+0x2c/0x127
[<ffffffff8115ef93>] ? sysfs_get_active_two+0x31/0x48
[<ffffffff8142f73f>] mutex_lock_nested+0x3e/0x43
[<ffffffffa02ba5fc>] fcoe_create+0x27/0x4f7 [fcoe]
[<ffffffff810635b1>] param_attr_store+0x27/0x35
[<ffffffff81063619>] module_attr_store+0x26/0x2a
[<ffffffff8115dae3>] sysfs_write_file+0x108/0x144
[<ffffffff81107bd1>] vfs_write+0xae/0x10b
[<ffffffff81076596>] ? trace_hardirqs_on_caller+0x125/0x150
[<ffffffff81107cee>] sys_write+0x4a/0x6e
[<ffffffff81009b42>] system_call_fastpath+0x16/0x1b
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch creates a port_id member in struct fc_lport.
This allows libfc to just deal with fc_lport instances
instead of calling into the fc_host to get the port_id.
This change helps in only using symbols necessary for
operation from the libfc structures. libfc still needs
to change the fc_host_port_id() if the port_id changes
so the presentation layer (scsi_transport_fc) can provide
the user with the correct value, but libfc shouldn't
rely on the presentation layer for operational values.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
It doesn't make sense to update the link speed in the is_link_ok()
routine. Move it to it's own routine and acquire the device speed
when we're configuring the device initially as well as if there are
any netdev events received.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The fcf pointer is checked again after this verification
making the first check redundant. Remote the first check.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
fcoe_create exits using out_nodev label when module is not
yet LIVE but this exit path unlocks the rtnl_lock though
rtnl lock was not held in this case.
So this patch replaces out_nodev with out_nomod to exit
w/o unlocking rtnl_lock.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
After the recent patch "fixes unnecessary seq id jump"
the SCST module fcst stopped working because multi-sequence
write data wasn't finding the sequence after the first frame.
Add back the setting of the seq_id when the first frame arrives.
Also fix indentation on two lines.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
1) Allow transition to NEED RESET state only from READY state for ISP82xx.
2) Avoid infinite ISP aborts when chip reset fails.
3) Code cleanup to remove some of the unused debug code.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The problem occurring is a hw-race where there's an outstanding read-flash
operation occurring while the chip is being reset (done via an sg_reset script).
After the chip is paused, the read-flash operation never completes and the
DPC thread, while trying to complete the reset, is never able to recover,
as the HW appears to be hung...
The fix is to wait for outstanding flash operation prior to doing a sg_reset -h.
And to wait for reset to complete before any flash operations.
Note, during the wait, if any of the operation (reset/flash) does not complete,
failure is returned to the upper layer. The upper layer either need to
fail or retry.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The qla2xxx driver uses a port_id_t to mark the start of its enumerations. gcc
is complaining that wrap.b24 may be used uninitialized, but this doesn't look
to be possible. Silence it.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently we can only issue the task management (TM)
commands via the mailbox mechanism. This is a limitation,
since only one mailbox command can be issued at a time.
The purpose of this effort is to provide support for
issuing and processing the respose to TM and Marker
IOCBs asynchronously. Towards achieving this, the
consolidated srb architecture that is currently used for
BSG and IOCB/Logio commands has been enhanced and used.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently, BSG and IOCB/Logio commands have a different
framework (srb structs). The purpose of this effort is to
consolidate them into a generalized framework for these
as well as other asynchronous operations in the future.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Migrate to a consistent set of debug entries during status-IOCB
handling:
* group CS_TIMEOUT handling with CS_PORT_UNAVAILABLE and the like
(more regrouping of common behaviour).
* drop CS_DATA_OVERRUN handling as it now falls into the
'default' case (still returns DID_ERROR).
* consolidate CS_RESET and CS_ABORTED handling, as we the only
functional difference was a printk() (still returns DID_RESET).
* dropped all the earlier inconsistent [qla_]printk()s sprinkled
throught the needlessly large case-statement. Failure case
I/Os are now logged with a 'standard' format:
<command failure details>
<command generic details>
so, for example a dropped-frame is logged as:
qla2xxx 0000:13:00.0: scsi(16:0:0) Dropped frame(s) detected (4000 of 4000 bytes).
qla2xxx 0000:13:00.0: scsi(16:0:0) FCP command status: 0x15-0x18 (70018) \
oxid=78 ser=76 cdb=280000 len=4000 rsp_info=0 resid=0 fw_resid=4000
which should now convey all relevant information.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The driver should not be unloaded if any application is using it.
To disallow driver unload, driver use count must be incremented.
Application uses this char device as handle and increases driver
use count to avoid possible driver unload.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently error status is cleared only after the uncorrectable fatal errors
in the qla2xxx_pci_slot_reset. This fix is added to clear the error status in
qla2xxx_pci_resume. This way for both fatal and non-fatal errors the error
status gets cleared properly.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=572258
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
With qla2xxx using mid-layer async-scsi-scanning, the link state for
disconnected port is displayed wrong. Additional check for cable presence
is considered to display proper link state.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
commit 70b25f890c
Author: Tejun Heo <tj@kernel.org>
Date: Thu Apr 15 09:00:08 2010 +0900
[SCSI] fix locking around blk_abort_request()
Introduced a reference before check problem, fix this by moving the
lock shorthand code to be right at the point of actual use.
Reported-by: Dan Carpenter <error27@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
dev_node_t was only used to transport some minor/major numbers
from the PCMCIA device drivers to deprecated userspace helpers.
However, only a few drivers made use of it, and the userspace
helpers are deprecated anyways. Therefore, get rid of dev_node_t .
As a first step, remove any usage of dev_node_t from drivers which
only wrote to this typedef/struct, but did not make use of it.
CC: linux-bluetooth@vger.kernel.org
CC: Harald Welte <laforge@gnumonks.org>
CC: linux-mtd@lists.infradead.org
CC: linux-wireless@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-serial@vger.kernel.org
CC: alsa-devel@alsa-project.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Instead of the old pcmcia_request_irq() interface, drivers may now
choose between:
- calling request_irq/free_irq directly. Use the IRQ from *p_dev->irq.
- use pcmcia_request_irq(p_dev, handler_t); the PCMCIA core will
clean up automatically on calls to pcmcia_disable_device() or
device ejection.
- drivers still not capable of IRQF_SHARED (or not telling us so) may
use the deprecated pcmcia_request_exclusive_irq() for the time
being; they might receive a shared IRQ nonetheless.
CC: linux-bluetooth@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-serial@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: linux-usb@vger.kernel.org
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
There's nastyness in the way we currently handle barriers (and
discards): They're effectively filesystem commands, but they get
processed as BLOCK_PC commands. Unfortunately BLOCK_PC commands are
taken by SCSI to be SG_IO commands and the issuer expects to see and
handle any returned errors, however trivial. This leads to a huge
problem, because the block layer doesn't expect this to happen and any
trivially retryable error on a barrier causes an immediate I/O error
to the filesystem.
The only real way to hack around this is to take the usual class of
offending errors (unit attentions) and make them all retryable in the
case of a REQ_HARDBARRIER. A correct fix would involve a rework of
the entire block and SCSI submit system, and so is out of scope for a
quick fix.
Cc: Hannes Reinecke <hare@suse.de>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Some arrays are giving I/O errors with ext3 filesystems when
SYNCHRONIZE_CACHE gets a UNIT_ATTENTION. What is happening is that
these commands have no retries, so the UNIT_ATTENTION causes the
barrier to fail. We should be enable retries here to clear any
transient error and allow the barrier to succeed.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
wd33c93_release() has been empty since ages, and sgiwd93.c no longer calls it
since its conversion to a proper platform driver 2 years ago. Also remove the
callers in the m68k wd33c93 shims.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
used cmd->host_scribble to store iocb command handle.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Per RFC 3720, Login Response Status Code 0x02 should not be retried.
Condensed connection error checking code to a single routine, and
added check for status class 0x02.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Updated firmware ready timeout algorithm to prevent
long delays and use jiffies to time out instead of
counter. Also use msleep_interruptible instead of msleep.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Link Down -> Mark all devices missing
Previously, the driver took no action on a Link Down,
and waited for the I/O on a dead connection to timeout
in the firmware before marking the DDB missing.
Link Up -> Mark all devices online
F/W will do auto login to all the devices only once.
After that its the responsibility of the driver to
relogin to devices whenever there is :
* Any sort of connection failure or
* KATO expires indicating target has logged out or
* I/O times out etc.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If cxgb3i_pdu_init() fails, then it appears that cxgb3i_iscsi_init()
will not be cleaned up, leading to the iscsi transport being left
registered. Fix this by adding a call to cxgb3i_iscsi_cleanup() on the
error path.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Karen Xie <kxie@chelsio.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In the scsi_debug driver, the virtual_gb option ignores the
sector_size, implicitly assuming that is 512 bytes. So if
'virtual_gb=1 sector_size=4096' the result is an 8 GB (virtual) disk.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This fixes a regression introduced with this commit:
commit d3305f3407
Author: Mike Christie <michaelc@cs.wisc.edu>
Date: Thu Aug 20 15:10:58 2009 -0500
[SCSI] libiscsi: don't increment cmdsn if cmd is not sent
in 2.6.32.
When I moved the hdr->cmdsn after init_task, I added
a bug when header digests are used. The problem is
that the LLD may calculate the header digest in init_task,
so if we then set the cmdsn after the init_task call we
change what the digest will be calculated by the target.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In the original code we dereferenced "pm8001_dev" before checking if it
was null. This patch moves the dereference inside the condition.
This was found by a static checker (smatch). I looked, but I couldn't
tell if "pm8001_dev" dev was ever actually null. The approach in this
patch seemed like the safest response.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If a command times out resulting in EH getting invoked, we wait for the
aborted commands to come back after sending the abort. Shorten
the amount of time we wait for these responses, to ensure we don't
get stuck in EH for several minutes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Commands which are completed by the VIOS are placed on a CRQ
in kernel memory for the ibmvfc driver to process. Each CRQ
entry is 16 bytes. The ibmvfc driver reads the first 8 bytes
to check if the entry is valid, then reads the next 8 bytes to get
the handle, which is a pointer the completed command. This fixes
an issue seen on Power 7 where the processor reordered the
loads from memory, resulting in processing command completion
with a stale handle. This could result in command timeouts,
and also early completion of commands.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch removes unnecessary #define's from hpsa. The SCSI midlayer
handles all this for us.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
