ST-Ericsson uses User Interface Boards to extend functionality of
some of their development boards. However, these aren't compatible
with all the supported boards found in Mainline (Snowball for
instance). This patch ensures that the UIBs are only probed on
boards which can actually support them. This in turn saves lots of
unnecessary error messages normally found in Snowball's boot log.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The final piece of the ab8500 puzzle. Here we prevent any of the ab8500-*
drivers from being registered from platform code when Device Tree is
enabled, as we expect DT do probe each of these individually. We also
provide the relevant compatible strings, so that DT knows which nodes
it needs to pay attention to during population.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch applies the correct format requested by the irq
domain. For chained IRQs which use GPIO lines as IRQs, we
stipulate that a two cell request is required. The first cell
contains the requested IRQ and the second can contain flags
pertaining to edge detection and level sensitive values. The
zeroth cell specifies the GPIO controller by use of a phandle.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The patch to disable SMSC911x registration was applied twice in the upstream
kernel by mistake. Git interpreted this as 'take the same entry from a
similar struct' which was close by. This was the wrong thing to do. This patch
rectifies this error and re-enables SMSC911x registration when Device Tree is
not enabled.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Apply db8500 related PRCMU Device Tree settings and clean up some formatting
errors. We also remove one of the PRCMU assigned IRQs, as it is currently not
used.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now the DB8500 has Device Tree support it will be probed when the DT
is parsed, rendering the requirement for platform registration void.
This patch removes DB8500 PRCMU platform registration.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now the SCMC911x is correctly enabled in Device Tree, there is no need
to continue registering it from platform code. In fact, if we continue
doing so, the system will throw an error on boot.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
During Device Tree enablement it is necessary to remove
<hw_component>_add_<device> calls one at at time, as and when particular
devices are DT enabled. This patch provides a temporary solution. Once
the new *of_init_devices function has been fully unpopulated it will be
removed again.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
During Device Tree enablement it is necessary to remove snowball_<device>*
platform_data segments one at at time, as and when particular devices are
DT enabled. This patch provides a temporary solution. Once this new struct
is empty it will be removed again.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull two small kvm fixes from Avi Kivity:
"A build fix for non-kvm archs and a transparent hugepage refcount
bugfix on hosts with 4M pages."
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Export asm-generic/kvm_para.h
KVM: MMU: fix huge page adapted on non-PAE host
Pull s390 patches from Heiko Carstens:
"A couple of s390 patches for the 3.5 merge window. Just a collection
of bug fixes and cleanups."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/uaccess: fix access_ok compile warnings
s390/cmpxchg: select HAVE_CMPXCHG_LOCAL option
s390/cmpxchg: fix sign extension bugs
s390/cmpxchg: fix 1 and 2 byte memory accesses
s390/cmpxchg: fix compile warnings specific to s390
s390/cmpxchg: add missing memory barrier to cmpxchg64
s390/cpu: remove cpu "capabilities" sysfs attribute
s390/kernel: Fix smp_call_ipl_cpu() for offline CPUs
s390/kernel: Introduce memcpy_absolute() function
s390/headers: replace __s390x__ with CONFIG_64BIT where possible
s390/headers: remove #ifdef __KERNEL__ from not exported headers
s390/irq: split irq stats for cpu-measurement alert facilities
s390/kexec: Move early_pgm_check_handler() to text section
s390/kdump: Use real mode for PSW restart and kexec
s390/kdump: Account /sys/kernel/kexec_crash_size changes in OS info
s390/kernel: Remove OS info init function call and diag 308 for kdump
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPx039AAoJEDeqqVYsXL0Ml90H/06bB0sH5gpmJPOcMOcz2y5n
xZH4nHFGFfDUou/NFBkjBFAveBZDFy1WwsSwN44RZobmtkmqj9tfF90R0EoRsew6
kfRKJAn2iYA67WpM33v0ZpI+00VpNBt/sXP6OM08FebPu1aGriTnLm3qaOutyeC4
Q9dMHwhsMBjTcD52TlTlPBFHfOTvpB1FZmw//TwujPZ56upFw+dI1FkvzxdrG68a
ES7h8QBD8GXaM6OC8klCqq36iMjP2wJK3A+9MsERxkGLjfGEGMLC7jV3MgwvfjHY
i5w/EUheOU4SLicu7jBoC9mPHzhsWdl7OCP+E7V2CGXGysKSu4lH65ft1bMRIvg=
=ZAzL
-----END PGP SIGNATURE-----
Merge tag 'parisc-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
Pull misc parisc updates from James Bottomley:
"This is a couple of updates to complete our fixes and one to fix a
compile failure caused during the merge window. Additionally, we now
switch to the generic strncopy_from_user."
* tag 'parisc-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] update parisc to use generic strncpy_from_user()
[PARISC] Fix parisc compile failure after smp: Add task_struct argument to __cpu_up()
[PARISC] fix TLB fault path on PA2.0 narrow systems
[PARISC] fix boot failure on 32-bit systems caused by branch stubs placed before .text
Pull additional x86 fixes from Peter Anvin.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, amd, xen: Avoid NULL pointer paravirt references
x86, mtrr: Fix a type overflow in range_to_mtrr func
x86, realmode: Unbreak the ia64 build of drivers/acpi/sleep.c
x86/mm/pat: Improve scaling of pat_pagerange_is_ram()
x86: hpet: Fix copy-and-paste mistake in earlier change
x86/mce: Fix 32-bit build
x86/bitops: Move BIT_64() for a wider use
This branch contains a few development patches for Samsung and Versatile
Express that were submitted to arm-soc near the beginning of the merge
window. We picked them up with the agreement that they would need to
sit in linux-next for a while, and now they have.
There are also two fixes:
- One long-standing build breakage on ixp4xx due to missing gpiolib
dependencies.
- The other is for some gpio device tree changes needed on lpc32xx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=IA3W
-----END PGP SIGNATURE-----
Merge tag 'devel-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late-merged development and first fixes for arm-soc from Olof Johansson:
"This branch contains a few development patches for Samsung and
Versatile Express that were submitted to arm-soc near the beginning of
the merge window. We picked them up with the agreement that they
would need to sit in linux-next for a while, and now they have.
There are also two fixes:
- One long-standing build breakage on ixp4xx due to missing gpiolib
dependencies.
- The other is for some gpio device tree changes needed on lpc32xx."
* tag 'devel-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: LPC32xx: Adjust dts files to gpio dt binding
ixp4xx: fix compilation by adding gpiolib support
ARM: vexpress: Remove twice included header files
ARM: vexpress: Device Tree updates
ARM: EXYNOS: Support suspend and resume for EXYNOS5250
ARM: EXYNOS: Add Clock register list for save and restore
ARM: EXYNOS: Add PMU table for EXYNOS5250
ARM: EXYNOS: Rename of function for pm.c
ARM: EXYNOS: Remove GIC save & restore function
ARM: dts: Add node for interrupt combiner controller on EXYNOS5250
ARM: S3C24XX: add support for second irq set of S3C2416
ARM: S3C64XX: use timekeeping wrapper on cpuidle
ARM: S3C64XX: declare the states with the new api on cpuidle
ARM: S3C64XX: Hook up carrier class modules on Cragganmore
ARM: S3C64XX: Initial hookup for Bells module on Cragganmore
Pull Sparc updates from David S. Miller:
1) Remove the idiotic situation wherein Leon was a special case in all
of the TLB/cache handling code.
The worst side effect of this bogosity is that you couldn't build a
kernel with Leon support enabled (to get better build coverage), and
test boot it on a non-LEON cpu.
Leon is, in all core respects, programatically identical to the
32-bit SRMMU. Except that they put the TLB registers in a different
alternate address space location.
Through code patching (for fast paths) and run time checks, this
issue is now a thing of the past.
From Sam Ravnborg.
2) There was a mis-merge of arch/sparc/Kconfig for one of the
clockevents changes that went in, causing 32-bit sparc to start
failing to build.
I merged in your tree to get those clockevents changes (and added a
note to the merge commit) then added Stephen Rothwell's fix for the
merge error.
3) Software quad floating point emulation was not working properly on
more recent Niagara chips, because the way the situation is reported
by the cpu has changed.
Nobody noticed because gcc emits calls to software emulation
routines in glibc.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc: (25 commits)
sparc: fix sparc64 build due to leon.h inclusion
sparc32: remove unused variable in head_32.S
sparc32,leon: fix leon bootup
sparc32: Export leon_dma_ops to modules.
sparc32: support leon + sun in dma_make_coherent()
sparc32,leon: always support leon in ioport
sparc32,leon: always include leon_pmc in build
sparc32: refactor cpu_idle()
sparc32: srmmu_probe now knows about leon too
sparc32: drop LEON hack for ASI_M_MMUREGS
sparc32: introduce run-time patching of srmmu access functions
sparc32: introduce support for run-time patching for all shared assembler code
sparc32,leon: fix section mismatch warning
sparc32,leon: always include leon_smp + leon_mm in build
sparc32,leon: always include leon_kernel in build
sparc32,leon: clean up leon.h
sparc32: handle leon in cpu.c
sparc32: handle leon in irq_32.c
sparc32: add support for run-time patching of leon/sun single instructions
sparc32: introduce sparc32_start_kernel called from head_32.S
...
get_unmapped_area() returns -E... on failure, not 0. Moreover, the
wrapper around it is completely pointless.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The GPIO devicetree binding in 3.5 doesn't register the various LPC32xx GPIO
banks via DT subnodes but always all at once, and changes the gpio referencing
to 3 cells (bank, gpio, flags). This patch adjusts the DTS files to this
binding that was just accepted to the gpio subsystem.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Stub out MSR methods that aren't actually needed. This fixes a crash
as Xen Dom0 on AMD Trinity systems. A bigger patch should be added to
remove the paravirt machinery completely for the methods which
apparently have no users!
Reported-by: Andre Przywara <andre.przywara@amd.com>
Link: http://lkml.kernel.org/r/20120530222356.GA28417@andromeda.dapyr.net
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@vger.kernel.org>
* late/soc:
ARM: vexpress: Remove twice included header files
ARM: vexpress: Device Tree updates
ARM: EXYNOS: Support suspend and resume for EXYNOS5250
ARM: EXYNOS: Add Clock register list for save and restore
ARM: EXYNOS: Add PMU table for EXYNOS5250
ARM: EXYNOS: Rename of function for pm.c
ARM: EXYNOS: Remove GIC save & restore function
ARM: dts: Add node for interrupt combiner controller on EXYNOS5250
ARM: S3C24XX: add support for second irq set of S3C2416
Use unsigned long for dealing with jiffies not int. Rename the
callback to something sensible. Use __this_cpu_read/write for
accessing per cpu data.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When boot on sun G5+ with 4T mem, see an overflow in mtrr cleanup as below.
*BAD*gran_size: 2G chunk_size: 2G num_reg: 10 lose cover RAM:
-18014398505283592M
This is because 1<<31 sign extended. Use an unsigned long constant to
fix it. Useful for mem larger than or equal to 4T.
-v2: Use 64bit constant instead of explicit type conversion as suggested
by Yinghai. Description updated too.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Link: http://lkml.kernel.org/r/4FC5A77F.6060505@oracle.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Revert usage of acpi_wakeup_address and move definition
to x86 architecture code in order to make compilation work
in ia64.
[jsakkine: tested compilation in ia64/x86-64 and added
proper commit message]
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Originally-by: H. Peter Anvin <hpa@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Link: http://lkml.kernel.org/r/1338370421-27735-1-git-send-email-jarkko.sakkinen@intel.com
Cc: Tony Luck <tony.luck@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Since nr_cpus_allowed is used outside of sched/rt.c and wants to be
used outside of there more, move it to a more natural site.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-kr61f02y9brwzkh6x53pdptm@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit commit 8e7fbcbc2 ("sched: Remove stale power aware scheduling
remnants and dysfunctional knobs") made a boo-boo with removing the
power aware scheduling muck from the x86 topology bits.
We should unconditionally use the llc_shared mask for multi-core.
Reported-and-tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Borislav Petkov <bp@amd64.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Link: http://lkml.kernel.org/n/tip-lsksc2kfyeveb13avh327p0d@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Function pat_pagerange_is_ram() scales poorly to large address
ranges, because it probes the resource tree for each page.
On a 2.6 GHz Opteron, this function consumes 34 ms for a 1 GB range.
It is called twice during untrack_pfn_vma(), slowing process
cleanup and handicapping the OOM killer.
This replacement consumes less than 1ms, under the same conditions.
Signed-off-by: John Dykstra <jdykstra@cray.com> on behalf of Cray Inc.
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1337980366.1979.6.camel@redwood
[ Small stylistic cleanups and renames ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On s390 access_ok is a macro which discards all parameters and always
returns 1. This can result in compile warnings which warn about unused
variables like this:
fs/read_write.c: In function 'rw_copy_check_uvector':
fs/read_write.c:684:16: warning: unused variable 'buf' [-Wunused-variable]
Fix this by adding a __range_ok() function which consumes all parameters
but still always returns 1.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Now that hopefully all cmpxchg/xchg bugs have been fixed select
HAVE_CMPXCHG_LOCAL option which uncovered a couple of bugs on s390.
The only call site which is affected seems to be within mm/vmstat.c.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For 1 and 2 byte operands for xchg and cmpxchg the old and new values
get or'ed into the larger 4 byte old value before the compare and swap
instruction gets executed. This is done without using the proper byte
mask before or'ing the values.
If the caller passed in negative old or new values these got sign
extended by the caller. Which in turn means that either the old value
never matches, or, even worse, unrelated bytes would be changed in memory.
Luckily there don't seem to be any callers around yet, since that would
have resulted in the specification exception fixed in an earlies patch.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When accessing a 1 or 2 byte memory operand we cannot use the
passed address since the compare and swap instruction only works
for 4 byte aligned memory operands.
Hence we calculate an aligned address so that compare and swap works
correctly. However we don't pass the calculated address to the inline
assembly. This results in incorrect memory accesses and in a
specification exception if used on non 4 byte aligned memory operands.
Since this didn't happen until now, there don't seem to be
too many users of cmpxchg on unaligned addresses.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The cmpxchg macros and functions are a bit different than on other
architectures. In particular the macros do not store the return
value of a __cmpxchg function call in a variable before returning the
value.
This causes compile warnings that only occur on s390 like this one:
net/ipv4/af_inet.c: In function 'build_ehash_secret':
net/ipv4/af_inet.c:241:2: warning: value computed is not used [-Wunused-value]
To get rid of these warnings use the same construct that we already use
for the xchg macro, which was introduced for the same reason.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
All cmpxchg functions imply a memory barrier.
cmpxch64 did not have one for 31 bit code, so add it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It has been a big mistage to add the capabilities attribute to the
cpus in sysfs:
First the attribute only contains the cpu capability of primary cpus,
which however is not necessarily (or better: unlikely) the type of
cpu the kernel runs on, which is typically an IFL.
In addition all information that is necessary is available in
/proc/sysinfo already. So this attribute partially duplicated
informations.
So programs should look into the sysinfo file to retrieve all
informations they are interested in.
Since with this kernel release also the powersavings cpu attributes
are removed this seems to be a good opportunity to remove another
broken interface.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the IPL CPU is offline, currently the pcpu_delegate() function
used by smp_call_ipl_cpu() does not work because pcpu_delegate()
modifies the lowcore of the target CPU. In case of an offline
IPL CPU currently the prefix register is zero but pcpu->lowcore
still points to the old prefix page. Therefore the lowcore changes
done by pcpu_delegate() have no effect.
With this fix pcpu_delegate() now uses memcpy_absolute() and therefore
also prepares the absolute zero lowcore if the target CPU has prefix
register zero.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch introduces the new function memcpy_absolute() that allows to
copy memory using absolute addressing. This means that the prefix swap
does not apply when this function is used.
With this patch also all s390 kernel code that accesses absolute zero
now uses the new memcpy_absolute() function. The old and less generic
copy_to_absolute_zero() function is removed.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull x86 trampoline rework from H. Peter Anvin:
"This code reworks all the "trampoline"/"realmode" code (various bits
that need to live in the first megabyte of memory, most but not all of
which runs in real mode at some point) in the kernel into a single
object. The main reason for doing this is that it eliminates the last
place in the kernel where we needed pages to be mapped RWX. This code
separates all that code into proper R/RW/RX pages."
Fix up conflicts in arch/x86/kernel/Makefile (mca removed next to reboot
code), and arch/x86/kernel/reboot.c (reboot code moved around in one
branch, modified in this one), and arch/x86/tools/relocs.c (mostly same
code came in earlier due to working around the ld bugs just before the
3.4 release).
Also remove stale x86-relocs entry from scripts/.gitignore as per Peter
Anvin.
* commit '61f5446169046c217a5479517edac3a890c3bee7': (36 commits)
x86, realmode: Move end signature into header.S
x86, relocs: When printing an error, say relative or absolute
x86, relocs: More relocations which may end up as absolute
x86, relocs: Workaround for binutils 2.22.52.0.1 section bug
xen-acpi-processor: Add missing #include <xen/xen.h>
acpi, bgrd: Add missing <linux/io.h> to drivers/acpi/bgrt.c
x86, realmode: Change EFER to a single u64 field
x86, realmode: Move kernel/realmode.c to realmode/init.c
x86, realmode: Move not-common bits out of trampoline_common.S
x86, realmode: Mask out EFER.LMA when saving trampoline EFER
x86, realmode: Fix no cache bits test in reboot_32.S
x86, realmode: Make sure all generated files are listed in targets
x86, realmode: build fix: remove duplicate build
x86, realmode: read cr4 and EFER from kernel for 64-bit trampoline
x86, realmode: fixes compilation issue in tboot.c
x86, realmode: move relocs from scripts/ to arch/x86/tools
x86, realmode: header for trampoline code
x86, realmode: flattened rm hierachy
x86, realmode: don't copy real_mode_header
x86, realmode: fix 64-bit wakeup sequence
...
Pull MIPS updates from Ralf Baechle:
"The whole series has been sitting in -next for quite a while with no
complaints. The last change to the series was before the weekend the
removal of an SPI patch which Grant - even though previously acked by
himself - appeared to raise objections. So I removed it until the
situation is clarified. Other than that all the patches have the acks
from their respective maintainers, all MIPS and x86 defconfigs are
building fine and I'm not aware of any problems introduced by this
series.
Among the key features for this patch series is a sizable patchset for
Lantiq which among other things introduces support for Lantiq's
flagship product, the FALCON SOC. It also means that the opensource
developers behind this patchset have overtaken Lantiq's competing
inhouse development team that was working behind closed doors.
Less noteworthy the ath79 patchset which adds support for a few more
chip variants, cleanups and fixes. Finally the usual dose of tweaking
of generic code."
Fix up trivial conflicts in arch/mips/lantiq/xway/gpio_{ebu,stp}.c where
printk spelling fixes clashed with file move and eventual removal of the
printk.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (81 commits)
MIPS: lantiq: remove orphaned code
MIPS: Remove all -Wall and almost all -Werror usage from arch/mips.
MIPS: lantiq: implement support for FALCON soc
MTD: MIPS: lantiq: verify that the NOR interface is available on falcon soc
MTD: MIPS: lantiq: implement OF support
watchdog: MIPS: lantiq: implement OF support and minor fixes
SERIAL: MIPS: lantiq: implement OF support
GPIO: MIPS: lantiq: convert gpio-stp-xway to OF
GPIO: MIPS: lantiq: convert gpio-mm-lantiq to OF and of_mm_gpio
GPIO: MIPS: lantiq: move gpio-stp and gpio-ebu to the subsystem folder
MIPS: pci: convert lantiq driver to OF
MIPS: lantiq: convert dma to platform driver
MIPS: lantiq: implement support for clkdev api
MIPS: lantiq: drop ltq_gpio_request() and gpio_to_irq()
OF: MIPS: lantiq: implement irq_domain support
OF: MIPS: lantiq: implement OF support
MIPS: lantiq: drop mips_machine support
OF: PCI: const usage needed by MIPS
MIPS: Cavium: Remove smp_reserve_lock.
MIPS: Move cache setup to setup_arch().
...
Pull arm updates from Russell King:
"This contains both some fixes found when trying to get the
Assabet+neponset setup as a replacement firewall with a 3c589 PCMCIA
card, and a bunch of changes from Al to fix up the ARM signal
handling, particularly some of the restart behaviour."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: neponset: make sure neponset_ncr_frob() is exported
ARM: fix out[bwl]()
arm: don't open-code ptrace_report_syscall()
arm: bury unused _TIF_RESTORE_SIGMASK
arm: remove unused restart trampoline
arm: new way of handling ERESTART_RESTARTBLOCK
arm: if we get into work_pending while returning to kernel mode, just go away
arm: don't call try_to_freeze() from do_signal()
arm: if there's no handler we need to restore sigmask, syscall or no syscall
arm: trim _TIF_WORK_MASK, get rid of useless test and branch...
arm: missing checks of __get_user()/__put_user() return values
In order to keep consistency with other rtc drivers,rename CONFIG_RTC_MXC
to CONFIG_RTC_DRV_MXC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
[akpm@linux-foundation.org: fix missed arch/arm/configs/imx_v6_v7_defconfig]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When holding the mmap_sem for reading, pmd_offset_map_lock should only
run on a pmd_t that has been read atomically from the pmdp pointer,
otherwise we may read only half of it leading to this crash.
PID: 11679 TASK: f06e8000 CPU: 3 COMMAND: "do_race_2_panic"
#0 [f06a9dd8] crash_kexec at c049b5ec
#1 [f06a9e2c] oops_end at c083d1c2
#2 [f06a9e40] no_context at c0433ded
#3 [f06a9e64] bad_area_nosemaphore at c043401a
#4 [f06a9e6c] __do_page_fault at c0434493
#5 [f06a9eec] do_page_fault at c083eb45
#6 [f06a9f04] error_code (via page_fault) at c083c5d5
EAX: 01fb470c EBX: fff35000 ECX: 00000003 EDX: 00000100 EBP:
00000000
DS: 007b ESI: 9e201000 ES: 007b EDI: 01fb4700 GS: 00e0
CS: 0060 EIP: c083bc14 ERR: ffffffff EFLAGS: 00010246
#7 [f06a9f38] _spin_lock at c083bc14
#8 [f06a9f44] sys_mincore at c0507b7d
#9 [f06a9fb0] system_call at c083becd
start len
EAX: ffffffda EBX: 9e200000 ECX: 00001000 EDX: 6228537f
DS: 007b ESI: 00000000 ES: 007b EDI: 003d0f00
SS: 007b ESP: 62285354 EBP: 62285388 GS: 0033
CS: 0073 EIP: 00291416 ERR: 000000da EFLAGS: 00000286
This should be a longstanding bug affecting x86 32bit PAE without THP.
Only archs with 64bit large pmd_t and 32bit unsigned long should be
affected.
With THP enabled the barrier() in pmd_none_or_trans_huge_or_clear_bad()
would partly hide the bug when the pmd transition from none to stable,
by forcing a re-read of the *pmd in pmd_offset_map_lock, but when THP is
enabled a new set of problem arises by the fact could then transition
freely in any of the none, pmd_trans_huge or pmd_trans_stable states.
So making the barrier in pmd_none_or_trans_huge_or_clear_bad()
unconditional isn't good idea and it would be a flakey solution.
This should be fully fixed by introducing a pmd_read_atomic that reads
the pmd in order with THP disabled, or by reading the pmd atomically
with cmpxchg8b with THP enabled.
Luckily this new race condition only triggers in the places that must
already be covered by pmd_none_or_trans_huge_or_clear_bad() so the fix
is localized there but this bug is not related to THP.
NOTE: this can trigger on x86 32bit systems with PAE enabled with more
than 4G of ram, otherwise the high part of the pmd will never risk to be
truncated because it would be zero at all times, in turn so hiding the
SMP race.
This bug was discovered and fully debugged by Ulrich, quote:
----
[..]
pmd_none_or_trans_huge_or_clear_bad() loads the content of edx and
eax.
496 static inline int pmd_none_or_trans_huge_or_clear_bad(pmd_t
*pmd)
497 {
498 /* depend on compiler for an atomic pmd read */
499 pmd_t pmdval = *pmd;
// edi = pmd pointer
0xc0507a74 <sys_mincore+548>: mov 0x8(%esp),%edi
...
// edx = PTE page table high address
0xc0507a84 <sys_mincore+564>: mov 0x4(%edi),%edx
...
// eax = PTE page table low address
0xc0507a8e <sys_mincore+574>: mov (%edi),%eax
[..]
Please note that the PMD is not read atomically. These are two "mov"
instructions where the high order bits of the PMD entry are fetched
first. Hence, the above machine code is prone to the following race.
- The PMD entry {high|low} is 0x0000000000000000.
The "mov" at 0xc0507a84 loads 0x00000000 into edx.
- A page fault (on another CPU) sneaks in between the two "mov"
instructions and instantiates the PMD.
- The PMD entry {high|low} is now 0x00000003fda38067.
The "mov" at 0xc0507a8e loads 0xfda38067 into eax.
----
Reported-by: Ulrich Obergfell <uobergfe@redhat.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen Rothwell <sfr@canb.auug.org.au> reported following error:
In file included from arch/sparc/kernel/prom_common.c:26:0:
arch/sparc/include/asm/leon.h:221:9: error: unknown type name 'irq_flow_handler_t'
arch/sparc/include/asm/leon.h:224:10: error: unknown type name 'irq_flow_handler_t'
Fix this by:
1) Avoid including leon.h in prom_commen.h (not needed)
2) Include irq.h in leon.h to avoid the missing symbol error
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
head_32.S failed to set cputypval for leon, causing boot to fail.
The boot failed because we failed to recognize this was a LEON
cpu so we did not preoperly run-time patch the the kernel.
This resulted in an early crash.
Reported-by: Daniel Hellstrom <daniel@gaisler.com>
Tested-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Konrad Eisele <konrad@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Rh0r
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"Besides the usual cleanups, this one brings:
* Support for 5 new chipsets: Intel's ICH LPC and SCH Centerton,
ST-E's STAX211, Samsung's MAX77693 and TI's LM3533.
* Device tree support for the twl6040, tps65910, da9502 and ab8500
drivers.
* Fairly big tps56910, ab8500 and db8500 updates.
* i2c support for mc13xxx.
* Our regular update for the wm8xxx driver from Mark."
Fix up various conflicts with other trees, largely due to ab5500 removal
etc.
* tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (106 commits)
mfd: Fix build break of max77693 by adding REGMAP_I2C option
mfd: Fix twl6040 build failure
mfd: Fix max77693 build failure
mfd: ab8500-core should depend on MFD_DB8500_PRCMU
gpio: tps65910: dt: process gpio specific device node info
mfd: Remove the parsing of dt info for tps65910 gpio
mfd: Save device node parsed platform data for tps65910 sub devices
mfd: Add r_select to lm3533 platform data
gpio: Add Intel Centerton support to gpio-sch
mfd: Emulate active low IRQs as well as active high IRQs for wm831x
mfd: Mark two lm3533 zone registers as volatile
mfd: Fix return type of lm533 attribute is_visible
mfd: Enable Device Tree support in the ab8500-pwm driver
mfd: Enable Device Tree support in the ab8500-sysctrl driver
mfd: Add support for Device Tree to twl6040
mfd: Register the twl6040 child for the ASoC codec unconditionally
mfd: Allocate twl6040 IRQ numbers dynamically
mfd: twl6040 code cleanup in interrupt initialization part
mfd: Enable ab8500-gpadc driver for Device Tree
mfd: Prevent unassigned pointer from being used in ab8500-gpadc driver
...
Pull kbuild updates from Michal Marek.
Fixed up nontrivial merge conflict in Makefile as per Stephen Rothwell
and linux-next (and trivial arch/sparc/Makefile changes due to removed
sparc32 logic).
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
mips: Fix KBUILD_CPPFLAGS definition
kbuild: fix ia64 link
kbuild: document KBUILD_LDS, KBUILD_VMLINUX_{INIT,MAIN} and LDFLAGS_vmlinux
kbuild: link of vmlinux moved to a script
kbuild: refactor final link of sparc32
kbuild: drop unused KBUILD_VMLINUX_OBJS from top-level Makefile
kbuild: Makefile: remove unnecessary check for m68knommu ARCH
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=oLXf
-----END PGP SIGNATURE-----
Merge tag 'writeback' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux
Pull writeback tree from Wu Fengguang:
"Mainly from Jan Kara to avoid iput() in the flusher threads."
* tag 'writeback' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
writeback: Avoid iput() from flusher thread
vfs: Rename end_writeback() to clear_inode()
vfs: Move waiting for inode writeback from end_writeback() to evict_inode()
writeback: Refactor writeback_single_inode()
writeback: Remove wb->list_lock from writeback_single_inode()
writeback: Separate inode requeueing after writeback
writeback: Move I_DIRTY_PAGES handling
writeback: Move requeueing when I_SYNC set to writeback_sb_inodes()
writeback: Move clearing of I_SYNC into inode_sync_complete()
writeback: initialize global_dirty_limit
fs: remove 8 bytes of padding from struct writeback_control on 64 bit builds
mm: page-writeback.c: local functions should not be exposed globally
Pull microblaze changes from Michal Simek.
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Setup correct pointer to TLS area
microblaze: Add TLS support to sys_clone
microblaze: ftrace: Pass the first calling instruction for dynamic ftrace
microblaze: Port OOM changes to do_page_fault
microblaze: Do not select GENERIC_GPIO by default
The huge page size is 4M on non-PAE host, but 2M page size is used in
transparent_hugepage_adjust(), so the page we get after adjust the
mapping level is not the head page, the BUG_ON() will be triggered
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
No need for two implementations - we check the cpu model.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
Unconditially define pci32_dma_ops as this is used
for leon.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
With the removal of sun4c we can use the same cpu_idle()
implementation on UP and SMP.
This also fix it so we use the same version independent on LEON
enabled or not.
V2: Fixed whitespace issue pointed out by Josip Rodin.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Josip Rodin <joy@entuzijast.net>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
All users of MMUREGS ASI is now LEON/SUN aware,
so this is no longer required.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
LEON uses a different ASI than SUN for MMUREGS
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
All users of MMUREGS ASI in kernel/ now uses run-time patching.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
Fix following warning:
WARNING: arch/sparc/kernel/built-in.o(.cpuinit.text+0x9f4): Section mismatch in reference from the function leon_callin() to the function .init.text:leon_configure_cache_smp()
The function __cpuinit leon_callin() references
a function __init leon_configure_cache_smp().
If leon_configure_cache_smp is only used by leon_callin then
annotate leon_configure_cache_smp with a matching annotation.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
Fix-up leon specific assembler to use ASI_LEON_MMUREGS
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
- Drop unused stuff accumulated over time
- Drop non-leon stuff
- Include almost all of the header unconditionally
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
A few hardcoded constant were replaced by symbolic
versions to improve readability
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
This will be used to handle that MMUREGS has different ASI for SUN and LEON.
This is the infrastructure only - users will come later.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
We use the compatibility property to determine the
sun models. For leon we use psr.impl and ignore the
result of the getprops call.
Include a hack to allow build as the support code
is not yet converted.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
Use PSR to check if the CPU is LEON and jump to
LEON specific code in this case.
Added a few constants to psr.h to increase readability.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
A few strings have been adopted to show more relevant info.
Julian Calaby <julian.calaby@gmail.com> pointed out one
that I would otherwise have missed.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Fixes this sparc32 defconfig build error:
timekeeping.c:(.text+0x277c4): undefined reference to `arch_gettimeoffset'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull in Linus's tree to get the commits that blew away
ARCH_USES_GETTIMEOFFSET but didn't update Sparc correctly, so
that I can apply Stephen Rothwell's fix for that mis-merge.
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic version is both easier to support and more correct.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is much the same as for SPARC except that we can do the find_zero()
function more efficiently using the count-leading-zeroes instructions.
Tested on 32-bit and 64-bit PowerPC.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lots of normal development commits, but perhaps most notable changes are:
* HDMI rework to properly decouple the HDMI audio part from the HDMI video part.
* Restructure omapdss core driver so that it's possible to implement device
tree support. This included changing how platform data is passed to the
drivers, changing display device registration and improving the panel driver's
ability to configure the underlying video output interface.
* Basic support for DSI packet interleaving
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=I8Se
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.5' of git://github.com/tomba/linux into fbdev-next
Omapdss driver changes for 3.5 merge window.
Lots of normal development commits, but perhaps most notable changes are:
* HDMI rework to properly decouple the HDMI audio part from the HDMI video part.
* Restructure omapdss core driver so that it's possible to implement device
tree support. This included changing how platform data is passed to the
drivers, changing display device registration and improving the panel driver's
ability to configure the underlying video output interface.
* Basic support for DSI packet interleaving
This makes <asm/word-at-a-time.h> actually live up to its promise of
allowing architectures to help tune the string functions that do their
work a word at a time.
David had already taken the x86 strncpy_from_user() function, modified
it to work on sparc, and then done the extra work to make it generically
useful. This then expands on that work by making x86 use that generic
version, completing the circle.
But more importantly, it fixes up the word-at-a-time interfaces so that
it's now easy to also support things like strnlen_user(), and pretty
much most random string functions.
David reports that it all works fine on sparc, and Jonas Bonn reported
that an earlier version of this worked on OpenRISC too. It's pretty
easy for architectures to add support for this and just replace their
private versions with the generic code.
* generic-string-functions:
sparc: use the new generic strnlen_user() function
x86: use the new generic strnlen_user() function
lib: add generic strnlen_user() function
word-at-a-time: make the interfaces truly generic
x86: use generic strncpy_from_user routine
A few device tree updates and an include file fix for versatile.
* 'vexpress-v3.4' of git://git.linaro.org/people/pawelmoll/linux:
ARM: vexpress: Remove twice included header files
ARM: vexpress: Device Tree updates
+ update to 3.4
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a patch series from Shawn Guo that moves from individual
late_initcalls() to using a member in the machine structure to invoke
a platform's late initcalls.
This cleanup is a step in the move towards multiplatform kernels since
it would reduce the need to check for compatible platforms in each and
every initcall.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=21h6
-----END PGP SIGNATURE-----
Merge tag 'cleanup-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull sweeping late_initcall cleanup for arm-soc from Olof Johansson:
"This is a patch series from Shawn Guo that moves from individual
late_initcalls() to using a member in the machine structure to invoke
a platform's late initcalls.
This cleanup is a step in the move towards multiplatform kernels since
it would reduce the need to check for compatible platforms in each and
every initcall."
Fix up trivial conflicts in arch/arm/mach-{exynos/mach-universal_c210.c,
imx/mach-cpuimx51.c, omap2/board-generic.c} due to changes nearby (and,
in the case of cpuimx51.c the board support being deleted)
* tag 'cleanup-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: ux500: use machine specific hook for late init
ARM: tegra: use machine specific hook for late init
ARM: shmobile: use machine specific hook for late init
ARM: sa1100: use machine specific hook for late init
ARM: s3c64xx: use machine specific hook for late init
ARM: prima2: use machine specific hook for late init
ARM: pnx4008: use machine specific hook for late init
ARM: omap2: use machine specific hook for late init
ARM: omap1: use machine specific hook for late init
ARM: msm: use machine specific hook for late init
ARM: imx: use machine specific hook for late init
ARM: exynos: use machine specific hook for late init
ARM: ep93xx: use machine specific hook for late init
ARM: davinci: use machine specific hook for late init
ARM: provide a late_initcall hook for platform initialization
This adds support for the spear13xx platform, which has first been under
review a long time ago and finally been completed after generic spear
work has gone into the clock, dt and pinctrl branches.
Also a number of updates for the samsung socs are part of this branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPuezDAAoJEIwa5zzehBx3mooP/iTHd1wRjr2MzKNx4+LpLWgl
aAXH002xe9Lvu7m75BRvEYWWdRLkyEy9ARM4s2wJCnxU41KmbF65ED1erxK8xaSe
Ako34vzH+HiUCM2DLzIP6FXyJMM7OcfrdGaY/GxOv+U+MzGUHeu3Q+8b0B/yfBnm
M3HdDrpyZHKZP9UM3wVQ4/ilDck6vEjYSV2jC11IaHiDMRD2nSpfRKh8H3+gv65S
gtj9EZpWM8CZg/fCe5lsm3PZnBnqHHW3WVafVnDQfGWeJYqZxMB5QKLU6qf/ntpx
LU2WjXoGaMmGBVZWynrwNEY6GVp3fZrDV30/q8Htf0/fBpEjUncrLHXtw0DxkpnK
UuyoRgn7zxOc3kDzohFNIexp1K3q+PNzXklR9hg7OSVji+9bPd2LIOEnpBeghBGj
WzZIebz5dIdddHlnOl4fRdmxZva2UTuI4bFAJ0izi10Mup7A9lrENnFHG/iVA0rQ
QlqJZoyeDCvbXQqZCgHirYRPhIxXdQj4G5IivfRxQ7Jgjy76Kt9uDp1egwezF/3a
2jVtcK42XokVv3Dhsvq9UNFn9GWdVImZ7eh70XLv+q834zAVxSzjWLtlS8I1Q5WO
7BGIJaICtugNwgYr44Dif6nsoVUmMnSwU5hVw1pApKZspN6EhMhMdp2hw8JPHFUs
mrZdHi1NAWuYSbObc3UB
=W2Ri
-----END PGP SIGNATURE-----
Merge tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc: soc specific changes (part 2) from Olof Johansson:
"This adds support for the spear13xx platform, which has first been
under review a long time ago and finally been completed after generic
spear work has gone into the clock, dt and pinctrl branches.
Also a number of updates for the samsung socs are part of this branch."
Fix up trivial conflicts in drivers/gpio/gpio-samsung.c that look much
worse than they are: the exonys5 init code was refactored in commit
fd454997d6 ("gpio: samsung: refactor gpiolib init for exynos4/5"), and
then commit f10590c983 ("ARM: EXYNOS: add GPC4 bank instance") added a
new gpio chip define and did tiny updates to the init code.
So the conflict diff looks like hell, but it's actually a fairly simple
change.
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
ARM: exynos: fix building with CONFIG_OF disabled
ARM: EXYNOS: Add AUXDATA for i2c controllers
ARM: dts: Update device tree source files for EXYNOS5250
ARM: EXYNOS: Add device tree support for interrupt combiner
ARM: EXYNOS: Add irq_domain support for interrupt combiner
ARM: EXYNOS: Remove a new bus_type instance for EXYNOS5
ARM: EXYNOS: update irqs for EXYNOS5250 SoC
ARM: EXYNOS: Add pre-divider and fout mux clocks for bpll and mpll
ARM: EXYNOS: add GPC4 bank instance
ARM: EXYNOS: Redefine IRQ_MCT_L0,1 definition
ARM: EXYNOS: Modify the GIC physical address for static io-mapping
ARM: EXYNOS: Add watchdog timer clock instance
pinctrl: SPEAr1310: Fix pin numbers for clcd_high_res
SPEAr: Update MAINTAINERS and Documentation
SPEAr13xx: Add defconfig
SPEAr13xx: Add compilation support
SPEAr13xx: Add dts and dtsi files
pinctrl: Add SPEAr13xx pinctrl drivers
pinctrl: SPEAr: Create macro for declaring GPIO PINS
SPEAr13xx: Add common clock framework support
...
These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WeDQ
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc device tree conversions (part 2) from Olof Johansson:
"These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier."
Fix up trivial conflicts due to nearby changes in
drivers/{gpio/gpio,i2c/busses/i2c}-mxs.c
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: dt: tegra: invert status=disable vs status=okay
ARM: dt: tegra: consistent basic property ordering
ARM: dt: tegra: sort nodes based on bus order
ARM: dt: tegra: remove duplicate device_type property
ARM: dt: tegra: consistenly use lower-case for hex constants
ARM: dt: tegra: format regs properties consistently
ARM: dt: tegra: gpio comment cleanup
ARM: dt: tegra: remove unnecessary unit addresses
ARM: dt: tegra: whitespace cleanup
ARM: dt: tegra cardhu: fix typo in SDHCI node name
ARM: dt: tegra: cardhu: register core regulator tps62361
ARM: dt: tegra30.dtsi: Add SMMU node
ARM: dt: tegra20.dtsi: Add GART node
ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra: Add device tree support for AHB
ARM: dts: enable audio support for imx28-evk
ARM: dts: enable i2c device for imx28-evk
i2c: mxs: add device tree probe support
ARM: dts: enable mmc for imx28-evk
...
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
More cleanups, continuing an earlier set with omap and samsung specific
cleanups. These could not go into the first set because they have
dependencies on various other series that in turn depend on the first
cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPuewtAAoJEIwa5zzehBx3J+gQAJKLV8ga5P3adkPAWEceewhX
pBjCgwgegs3V5GWhW3Svwhxpll5Djzzt891sAiZjh5eDZCfWy+CnxDJzyuh4mXok
zRIfEVLZOopTVV3B31Uq7e7cYEy61Hm6QY4yLGknjxKrrc4CG3G1puvrbLvm1RiL
tlFBdbCwwiLM6pnCyi6BTGKfvrbCgqpdaKSNmVjiwiKjAIvB8v++BsRxXXGWAbVR
fq8uyiClIB+xhghhsUBLQ6V+pxF+XrjRnoNtl5tQE4VqUUl81UdbJVDfU3L67Q/V
hFBNLf0uwO4ecu7Alyx+/c6Eax0N9tQ5VVtAkSRekKzID2/CoGp9w5JBwjctZNrm
LuPvzaq11q/GzkmcVjrJ/U3FIxgFta+v6cY2CYtZAAfmxw4oAgr25eMRKTUHDGoy
1F7SD3KOEqT1OFgrHVM9XLYAHL+5i27dnGsk0Nk4qGYZLYVLJ1nxUUNvxV8jfXyJ
AtqlYwm06vQxYLM86nV8g9xHssWBrOrCLEJ51rvjHfG+B5m5BifQlImGsHP1Xhut
gnLvak3r4Xkc6ipeROikY0wH/Ss8aE/F0fP0TZMXH9e45eA0EVQEp+qnJOcld5o4
CR63OTD6u9j9TbIbJXmleItkADfcrk2dCHs1tF42+KA9VJJsWxRjj1+S+NfLVihU
ScTFTiSPHPXAxWAwJIL1
=7UKB
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc cleanups (part 2) from Olof Johansson:
"More cleanups, continuing an earlier set with omap and samsung
specific cleanups. These could not go into the first set because they
have dependencies on various other series that in turn depend on the
first cleanups."
Fixed up conflicts in arch/arm/plat-omap/counter_32k.c due to commit
bd0493eaaf: "move read_{boot,persistent}_clock to the architecture
level" that changed how the persistent clocks were handled. And trivial
conflicts in arch/arm/mach-omap1/common.h due to just independent
changes close to each other.
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
ARM: SAMSUNG: merge plat-s5p into plat-samsung
ARM: SAMSUNG: move options for common s5p into plat-samsung/Kconfig
ARM: SAMSUNG: move setup code for s5p mfc and mipiphy into plat-samsung
ARM: SAMSUNG: move platform device for s5p uart into plat-samsung
ARM: SAMSUNG: move hr timer for common s5p into plat-samsung
ARM: SAMSUNG: move pm part for common s5p into plat-samsung
ARM: SAMSUNG: move interrupt part for common s5p into plat-samsung
ARM: SAMSUNG: move clock part for common s5p into plat-samsung
ARM: S3C24XX: Use common macro to define resources on dev-uart.c
ARM: S3C24XX: move common clock init into common.c
ARM: S3C24XX: move common power-management code to mach-s3c24xx
ARM: S3C24XX: move plat-s3c24xx/dev-uart.c into common.c
ARM: S3C24XX: move plat-s3c24xx/cpu.c
ARM: OMAP2+: Kconfig: convert SOC_OMAPAM33XX to SOC_AM33XX
ARM: OMAP2+: Kconfig: convert SOC_OMAPTI81XX to SOC_TI81XX
GPMC: add ECC control definitions
ARM: OMAP2+: dmtimer: remove redundant sysconfig context restore
ARM: OMAP: AM35xx: convert 3517 detection/flags to AM35xx
ARM: OMAP: AM35xx: remove redunant cpu_is checks for AM3505
ARM: OMAP1: Pass dma request lines in platform data to MMC driver
...
These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of the
samsung iommu code from a platform specific in-kernel interface to the
generic iommu subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hgkg
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc driver specific updates from Olof Johansson:
"These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of
the samsung iommu code from a platform specific in-kernel interface to
the generic iommu subsystem."
Fix up trivial conflicts in arch/arm/mach-exynos/Kconfig
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mmc: dt: Consolidate DT bindings
iommu/exynos: Add iommu driver for EXYNOS Platforms
ARM: davinci: optimize the DMA ISR
ARM: davinci: implement DEBUG_LL port choice
ARM: tegra: Add SMMU enabler in AHB
ARM: tegra: Add Tegra AHB driver
Input: pxa27x_keypad add choice to set direct_key_mask
Input: pxa27x_keypad direct key may be low active
Input: pxa27x_keypad bug fix for direct_key_mask
Input: pxa27x_keypad keep clock on as wakeup source
ARM: dt: tegra: pinmux changes for USB ULPI
ARM: tegra: add USB ULPI PHY reset GPIO to device tree
ARM: tegra: don't hard-code USB ULPI PHY reset_gpio
ARM: tegra: change pll_p_out4's rate to 24MHz
ARM: tegra: fix pclk rate
ARM: tegra: reparent sclk to pll_c_out1
ARM: tegra: Add pllc clock init table
ARM: dt: tegra cardhu: basic audio support
ARM: dt: tegra30.dtsi: Add audio-related nodes
ARM: tegra: add AUXDATA required for audio
...
For the first time, we have one branch that collects just updates to
defconfig files, mostly for adapting to changes in other subsystems.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pvPg
-----END PGP SIGNATURE-----
Merge tag 'defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc defconfig updates from Olof Johansson:
"For the first time, we have one branch that collects just updates to
defconfig files, mostly for adapting to changes in other subsystems."
* tag 'defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: PRIMA2: add prima2_defconfig for CSR SiRFprimaII
ARM: tegra: update defconfig
ARM: tegra: update defconfig
ARM: imx_v6_v7_defconfig: Add SPI NOR support
ARM: imx_v4_v5_defconfig: Let CONFIG_MACH_IMX27_DT be built by default
Now that all drivers are converted to OF we are able to remove some remaining
pieces of orphaned code.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3841/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This throws away the old x86-specific functions in favor of the generic
optimized version.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This changes the interfaces in <asm/word-at-a-time.h> to be a bit more
complicated, but a lot more generic.
In particular, it allows us to really do the operations efficiently on
both little-endian and big-endian machines, pretty much regardless of
machine details. For example, if you can rely on a fast population
count instruction on your architecture, this will allow you to make your
optimized <asm/word-at-a-time.h> file with that.
NOTE! The "generic" version in include/asm-generic/word-at-a-time.h is
not truly generic, it actually only works on big-endian. Why? Because
on little-endian the generic algorithms are wasteful, since you can
inevitably do better. The x86 implementation is an example of that.
(The only truly non-generic part of the asm-generic implementation is
the "find_zero()" function, and you could make a little-endian version
of it. And if the Kbuild infrastructure allowed us to pick a particular
header file, that would be lovely)
The <asm/word-at-a-time.h> functions are as follows:
- WORD_AT_A_TIME_CONSTANTS: specific constants that the algorithm
uses.
- has_zero(): take a word, and determine if it has a zero byte in it.
It gets the word, the pointer to the constant pool, and a pointer to
an intermediate "data" field it can set.
This is the "quick-and-dirty" zero tester: it's what is run inside
the hot loops.
- "prep_zero_mask()": take the word, the data that has_zero() produced,
and the constant pool, and generate an *exact* mask of which byte had
the first zero. This is run directly *outside* the loop, and allows
the "has_zero()" function to answer the "is there a zero byte"
question without necessarily getting exactly *which* byte is the
first one to contain a zero.
If you do multiple byte lookups concurrently (eg "hash_name()", which
looks for both NUL and '/' bytes), after you've done the prep_zero_mask()
phase, the result of those can be or'ed together to get the "either
or" case.
- The result from "prep_zero_mask()" can then be fed into "find_zero()"
(to find the byte offset of the first byte that was zero) or into
"zero_bytemask()" (to find the bytemask of the bytes preceding the
zero byte).
The existence of zero_bytemask() is optional, and is not necessary
for the normal string routines. But dentry name hashing needs it, so
if you enable DENTRY_WORD_AT_A_TIME you need to expose it.
This changes the generic strncpy_from_user() function and the dentry
hashing functions to use these modified word-at-a-time interfaces. This
gets us back to the optimized state of the x86 strncpy that we lost in
the previous commit when moving over to the generic version.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The generic strncpy_from_user() is not really optimal, since it is
designed to work on both little-endian and big-endian. And on
little-endian you can simplify much of the logic to find the first zero
byte, since little-endian arithmetic doesn't have to worry about the
carry bit propagating into earlier bytes (only later bytes, which we
don't care about).
But I have patches to make the generic routines use the architecture-
specific <asm/word-at-a-time.h> infrastructure, so that we can regain
the little-endian optimizations. But before we do that, switch over to
the generic routines to make the patches each do just one well-defined
thing.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=kG4e
-----END PGP SIGNATURE-----
Merge tag 'x86-mce-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull x86/mce merge window patches from Tony Luck:
"Including two that make error_context() checks less sucky"
* tag 'x86-mce-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
x86/mce: Add instruction recovery signatures to mce-severity table
x86/mce: Fix check for processor context when machine check was taken.
MCE: Fix vm86 handling for 32bit mce handler
x86/mce Add validation check before GHES error is recorded
x86/mce: Avoid reading every machine check bank register twice.
Pull tile updates from Chris Metcalf:
"These changes cover a range of new arch/tile features and
optimizations. They've been through LKML review and on linux-next for
a month or so. There's also one bug-fix that just missed 3.4, which
I've marked for stable."
Fixed up trivial conflict in arch/tile/Kconfig (new added tile Kconfig
entries clashing with the generic timer/clockevents changes).
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: default to tilegx_defconfig for ARCH=tile
tile: fix bug where fls(0) was not returning 0
arch/tile: mark TILEGX as not EXPERIMENTAL
tile/mm/fault.c: Port OOM changes to handle_page_fault
arch/tile: add descriptive text if the kernel reports a bad trap
arch/tile: allow querying cpu module information from the hypervisor
arch/tile: fix hardwall for tilegx and generalize for idn and ipi
arch/tile: support multiple huge page sizes dynamically
mm: add new arch_make_huge_pte() method for tile support
arch/tile: support kexec() for tilegx
arch/tile: support <asm/cachectl.h> header for cacheflush() syscall
arch/tile: Allow tilegx to build with either 16K or 64K page size
arch/tile: optimize get_user/put_user and friends
arch/tile: support building big-endian kernel
arch/tile: allow building Linux with transparent huge pages enabled
arch/tile: use interrupt critical sections less
There is no "ARCH=tile" (just like there is no "ARCH=x86") so we need
to pick a default configuration, either tilepro or tilegx, when users
specify ARCH=tile. We'll use tilegx, since that's our current chip.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This is because __builtin_clz(0) returns 64 for the "undefined" case
of 0, since the builtin just does a right-shift 32 and "clz" instruction.
So, use the alpha approach of casting to u32 and using __builtin_clzll().
Cc: stable@vger.kernel.org
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Also create a TILEPRO config setting to use for #ifdefs where it
is cleaner to do so, and make the 64BIT setting depend directly
on the setting of TILEGX.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Commit d065bd810b
(mm: retry page fault when blocking on disk transfer) and
commit 37b23e0525
(x86,mm: make pagefault killable)
The above commits introduced changes into the x86 pagefault handler
for making the page fault handler retryable as well as killable.
These changes reduce the mmap_sem hold time, which is crucial
during OOM killer invocation.
Port these changes to tile.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
[cmetcalf@tilera.com: initialize "flags" after "write" updated.]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
If the kernel unexpectedly takes a bad trap, it's convenient to
have it report the type of trap as part of the error. This gives
customers a bit more context before they call up customer support.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This just adds a few more attributes to the information Linux
can query from the hypervisor for the /sys/hypervisor/board/ directory,
providing part, serial#, revision#, and description for cpu modules
(as opposed to the board itself, or any mezzanine boards).
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The hardwall drain code was not properly implemented for tilegx,
just tilepro, so you couldn't reliably restart an application that
made use of the udn.
In addition, the code was only applicable to the udn (user dynamic
network). On tilegx there is a second user network that is available
(the "idn"), and there is support for having I/O shims deliver
user-level interrupts to applications ("ipi") which functions in a
very similar way to the inter-core permissions used for udn/idn.
So this change also generalizes the code from supporting just the udn
to supports udn/idn/ipi on tilegx.
By default we now use /dev/hardwall/{udn,idn,ipi} with separate
minor numbers for the three devices.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This change adds support for a new "super" bit in the PTE, using the new
arch_make_huge_pte() method. The Tilera hypervisor sees the bit set at a
given level of the page table and gangs together 4, 16, or 64 consecutive
pages from that level of the hierarchy to create a larger TLB entry.
One extra "super" page size can be specified at each of the three levels
of the page table hierarchy on tilegx, using the "hugepagesz" argument
on the boot command line. A new hypervisor API is added to allow Linux
to tell the hypervisor how many PTEs to gang together at each level of
the page table.
To allow pre-allocating huge pages larger than the buddy allocator can
handle, this change modifies the Tilera bootmem support to put all of
memory on tilegx platforms into bootmem.
As part of this change I eliminate the vestigial CONFIG_HIGHPTE support,
which never worked anyway, and eliminate the hv_page_size() API in favor
of the standard vma_kernel_pagesize() API.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
We already had a syscall that did some dcache flushing, but it was
not used in practice. Make it MIPS compatible instead so it can
do both the DCACHE and ICACHE actions. We have code that wants to
be able to use the ICACHE flush mode from userspace so this change
enables that.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This change introduces new flags for the hv_install_context()
API that passes a page table pointer to the hypervisor. Clients
can explicitly request 4K, 16K, or 64K small pages when they
install a new context. In practice, the page size is fixed at
kernel compile time and the same size is always requested every
time a new page table is installed.
The <hv/hypervisor.h> header changes so that it provides more abstract
macros for managing "page" things like PFNs and page tables. For
example there is now a HV_DEFAULT_PAGE_SIZE_SMALL instead of the old
HV_PAGE_SIZE_SMALL. The various PFN routines have been eliminated and
only PA- or PTFN-based ones remain (since PTFNs are always expressed
in fixed 2KB "page" size). The page-table management macros are
renamed with a leading underscore and take page-size arguments with
the presumption that clients will use those macros in some single
place to provide the "real" macros they will use themselves.
I happened to notice the old hv_set_caching() API was totally broken
(it assumed 4KB pages) so I changed it so it would nominally work
correctly with other page sizes.
Tag modules with the page size so you can't load a module built with
a conflicting page size. (And add a test for SMP while we're at it.)
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Use direct load/store for the get_user/put_user.
Previously, we would call out to a helper routine that would do the
appropriate thing and then return, handling the possible exception
internally. Now we inline the load or store, along with a "we succeeded"
indication in a register; if the load or store faults, we write a
"we failed" indication into the same register and then return to the
following instruction. This is more efficient and gives us more compact
code, as well as being more in line with what other architectures do.
The special futex assembly source file for TILE-Gx also disappears in
this change; we just use the same inlining idiom there as well, putting
the appropriate atomic operations directly into futex_atomic_op_inuser()
(and thus into the FUTEX_WAIT function).
The underlying atomic copy_from_user, copy_to_user functions were
renamed using the (cryptic) x86 convention as copy_from_user_ll and
copy_to_user_ll.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The toolchain supports big-endian mode now, so add support for building
the kernel to run big-endian as well.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The change adds some infrastructure for managing tile pmd's more generally,
using pte_pmd() and pmd_pte() methods to translate pmd values to and
from ptes, since on TILEPro a pmd is really just a nested structure
holding a pgd (aka pte). Several existing pmd methods are moved into
this framework, and a whole raft of additional pmd accessors are defined
that are used by the transparent hugepage framework.
The tile PTE now has a "client2" bit. The bit is used to indicate a
transparent huge page is in the process of being split into subpages.
This change also fixes a generic bug where the return value of the
generic pmdp_splitting_flush() was incorrect.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
In general we want to avoid ever touching memory while within an
interrupt critical section, since the page fault path goes through
a different path from the hypervisor when in an interrupt critical
section, and we carefully decided with tilegx that we didn't need
to support this path in the kernel. (On tilepro we did implement
that path as part of supporting atomic instructions in software.)
In practice we always need to touch the kernel stack, since that's
where we store the interrupt state before releasing the critical
section, but this change cleans up a few things. The IRQ_ENABLE
macro is split up so that when we want to enable interrupts in a
deferred way (e.g. for cpu_idle or for interrupt return) we can
read the per-cpu enable mask before entering the critical section.
The cache-migration code is changed to use interrupt masking instead
of interrupt critical sections. And, the interrupt-entry code is
changed so that we defer loading "tp" from per-cpu data until after
we have released the interrupt critical section.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Pull slave-dmaengine updates from Vinod Koul:
"Nothing exciting this time, odd fixes in a bunch of drivers"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: at_hdmac: take maxburst from slave configuration
dmaengine: at_hdmac: remove ATC_DEFAULT_CTRLA constant
dmaengine: at_hdmac: remove some at_dma_slave comments
dma: imx-sdma: make channel0 operations atomic
dmaengine: Fixup dmaengine_prep_slave_single() to be actually useful
dmaengine: Use dma_sg_len(sg) instead of sg->length
dmaengine: Use sg_dma_address instead of sg_phys
DMA: PL330: Remove duplicate header file inclusion
dma: imx-sdma: keep the callbacks invoked in the tasklet
dmaengine: dw_dma: add Device Tree probing capability
dmaengine: dw_dmac: Add clk_{un}prepare() support
dma/amba-pl08x: add support for the Nomadik variant
dma/amba-pl08x: check for terminal count status only
Pull CMA and ARM DMA-mapping updates from Marek Szyprowski:
"These patches contain two major updates for DMA mapping subsystem
(mainly for ARM architecture). First one is Contiguous Memory
Allocator (CMA) which makes it possible for device drivers to allocate
big contiguous chunks of memory after the system has booted.
The main difference from the similar frameworks is the fact that CMA
allows to transparently reuse the memory region reserved for the big
chunk allocation as a system memory, so no memory is wasted when no
big chunk is allocated. Once the alloc request is issued, the
framework migrates system pages to create space for the required big
chunk of physically contiguous memory.
For more information one can refer to nice LWN articles:
- 'A reworked contiguous memory allocator':
http://lwn.net/Articles/447405/
- 'CMA and ARM':
http://lwn.net/Articles/450286/
- 'A deep dive into CMA':
http://lwn.net/Articles/486301/
- and the following thread with the patches and links to all previous
versions:
https://lkml.org/lkml/2012/4/3/204
The main client for this new framework is ARM DMA-mapping subsystem.
The second part provides a complete redesign in ARM DMA-mapping
subsystem. The core implementation has been changed to use common
struct dma_map_ops based infrastructure with the recent updates for
new dma attributes merged in v3.4-rc2. This allows to use more than
one implementation of dma-mapping calls and change/select them on the
struct device basis. The first client of this new infractructure is
dmabounce implementation which has been completely cut out of the
core, common code.
The last patch of this redesign update introduces a new, experimental
implementation of dma-mapping calls on top of generic IOMMU framework.
This lets ARM sub-platform to transparently use IOMMU for DMA-mapping
calls if one provides required IOMMU hardware.
For more information please refer to the following thread:
http://www.spinics.net/lists/arm-kernel/msg175729.html
The last patch merges changes from both updates and provides a
resolution for the conflicts which cannot be avoided when patches have
been applied on the same files (mainly arch/arm/mm/dma-mapping.c)."
Acked by Andrew Morton <akpm@linux-foundation.org>:
"Yup, this one please. It's had much work, plenty of review and I
think even Russell is happy with it."
* 'for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping: (28 commits)
ARM: dma-mapping: use PMD size for section unmap
cma: fix migration mode
ARM: integrate CMA with DMA-mapping subsystem
X86: integrate CMA with DMA-mapping subsystem
drivers: add Contiguous Memory Allocator
mm: trigger page reclaim in alloc_contig_range() to stabilise watermarks
mm: extract reclaim code from __alloc_pages_direct_reclaim()
mm: Serialize access to min_free_kbytes
mm: page_isolation: MIGRATE_CMA isolation functions added
mm: mmzone: MIGRATE_CMA migration type added
mm: page_alloc: change fallbacks array handling
mm: page_alloc: introduce alloc_contig_range()
mm: compaction: export some of the functions
mm: compaction: introduce isolate_freepages_range()
mm: compaction: introduce map_pages()
mm: compaction: introduce isolate_migratepages_range()
mm: page_alloc: remove trailing whitespace
ARM: dma-mapping: add support for IOMMU mapper
ARM: dma-mapping: use alloc, mmap, free from dma_ops
ARM: dma-mapping: remove redundant code and do the cleanup
...
Conflicts:
arch/x86/include/asm/dma-mapping.h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)
iEYEABECAAYFAk+/R7EACgkQ31LbvUHyf1dp9QCfX9xPFDERRWwvyDAAl9zLONxj
K+kAnRNydbw7UglqIYUnreCfNemfMdmg
=w9Td
-----END PGP SIGNATURE-----
Merge tag 'cris-for-linus' of git://jni.nu/cris
Pull CRIS changes from Jesper Nilsson:
"No major changes here, but fixes some compile errors for CRIS, some
small style issues, some documentation and as a bonus nukes a couple
of obsolete rtc-files and related code."
* tag 'cris-for-linus' of git://jni.nu/cris:
cris: Remove old legacy "-traditional" flag from arch-v10/lib/Makefile
CRIS: Remove legacy RTC drivers
cris/mm/fault.c: Port OOM changes to do_page_fault
cris:fix the wrong function declear
CRIS: Add _sdata to vmlinux.lds.S
cris: posix_types.h, include asm-generic/posix_types.h
CRIS: Update documentation
cris/arch-v32: cryptocop: Use kzalloc
net:removed the unused variable
cris:removed the unused variable
CRISv32: Correct name of read_mostly section.
As per commits 2922585b93 ("lib: Sparc's strncpy_from_user is generic
enough, move under lib/") and 92ae03f2ef ("x86: merge 32/64-bit
versions of 'strncpy_from_user()' and speed it up"), and corresponding
discussion on linux-arch.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 8239c25f47 added an argument to our
__cpu_up() function, but didn't notice we have an extra definition for
this in asm/smp.h resulting in a compile failure.
Fix by removing the extraneous parisc definition of __cpu_up(). While
we're at it, remove the duplicated definition of smp_send_reschedule().
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
commit 5e185581d7
Author: James Bottomley <JBottomley@Parallels.com>
[PARISC] fix PA1.1 oops on boot
Didn't quite fix the crash on boot. It moved it from PA1.1 processors to
PA2.0 narrow kernels. The final fix is to make sure the [id]tlb_miss_20 paths
also work. Even on narrow systems, these paths require using the wide
instructions becuase the tlb insertion format is wide. Fix this by
conditioning the dep[wd],z on whether we're being called from _11 or _20[w]
paths.
Tested-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In certain configurations, the resulting kernel becomes too large to boot
because the linker places the long branch stubs for the merged .text section
at the very start of the image. As a result, the initial transfer of control
jumps to an unexpected location. Fix this by placing the head text in a
separate section so the stubs for .text are not at the start of the image.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This function is used by modules (such as the SA1111 PCMCIA driver)
so it needs to be exported.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
out[bwl]() had a side effect that gcc read-back from the register after
writing its value. This causes a problem for at least 3c589_cs, which
spits out lots of "adapter failure, FIFO diagnostic register 2011."
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
UltraSPARC-T2 and later do not use the fp_exception_other trap and do
not set the floating point trap type field in the %fsr at all when you
try to execute an unimplemented FPU operation.
Instead, it uses the illegal_instruction trap and it leaves the
floating point trap type field clear.
So we should not validate the %fsr trap type field when do_mathemu()
is invoked from the illegal instruction handler.
Also, the floating point trap type field is 3 bits, not 4 bits.
Signed-off-by: David S. Miller <davem@davemloft.net>
Setup a pointer to the TLS area in copy_thread.
r10 is 6th argumetn which contains TLS area.
And r21 is the thread reg.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Signed-off-by: David Holsgrove <david.holsgrove@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Formerly unused Args 4/5 now load parent tid / child tid so the brid to
do_fork can pick up TLS from r10. Arg 3 still unused
There is also necessary to fix old glibc which do not setup r9/r10 (arg 4/5).
Simple clearing them is fine.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Signed-off-by: David Holsgrove <david.holsgrove@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Selftest for dynamic ftrace requres to pass address of the first
calling instruction because hash function is calculated from it.
ftrace_update_ftrace_func setups pointer to function which is called
in _mcount function. trace_selftest is not aware about instruction
size (for microblaze 8 - imm and addik) and that's why we have
to pass in r5 address of imm not addik which is in r15.12
For more info look at ftrace_ops_list_func/ftrace.c.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Commit d065bd810b
(mm: retry page fault when blocking on disk transfer) and
commit 37b23e0525
(x86,mm: make pagefault killable)
The above commits introduced changes into the x86 pagefault handler
for making the page fault handler retryable as well as killable.
These changes reduce the mmap_sem hold time, which is crucial
during OOM killer invocation.
Port these changes to microblaze.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
The microblaze architecture does not provide a native GPIO API implementation
nor requires GPIOLIB, but still selects GENERIC_GPIO by default. As a result the
following build error occurs, if GPIOLIB is not selected:
include/asm-generic/gpio.h: In function 'gpio_get_value_cansleep':
include/asm-generic/gpio.h:218: error: implicit declaration of function '__gpio_get_value'
include/asm-generic/gpio.h: In function 'gpio_set_value_cansleep':
include/asm-generic/gpio.h:224: error: implicit declaration of function '__gpio_set_value'
This patch addresses the issue by not selecting GENERIC_GPIO by default. This
causes the GPIO API to be stubbed out if no implementation is provided.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: stable@vger.kernel.org
Tested-by: Michal Simek <monstr@monstr.eu>
Pull KVM changes from Avi Kivity:
"Changes include additional instruction emulation, page-crossing MMIO,
faster dirty logging, preventing the watchdog from killing a stopped
guest, module autoload, a new MSI ABI, and some minor optimizations
and fixes. Outside x86 we have a small s390 and a very large ppc
update.
Regarding the new (for kvm) rebaseless workflow, some of the patches
that were merged before we switch trees had to be rebased, while
others are true pulls. In either case the signoffs should be correct
now."
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
arch/powerpc/kvm/book3s_segment.S and arch/x86/include/asm/kvm_para.h.
I suspect the kvm_para.h resolution ends up doing the "do I have cpuid"
check effectively twice (it was done differently in two different
commits), but better safe than sorry ;)
* 'next' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (125 commits)
KVM: make asm-generic/kvm_para.h have an ifdef __KERNEL__ block
KVM: s390: onereg for timer related registers
KVM: s390: epoch difference and TOD programmable field
KVM: s390: KVM_GET/SET_ONEREG for s390
KVM: s390: add capability indicating COW support
KVM: Fix mmu_reload() clash with nested vmx event injection
KVM: MMU: Don't use RCU for lockless shadow walking
KVM: VMX: Optimize %ds, %es reload
KVM: VMX: Fix %ds/%es clobber
KVM: x86 emulator: convert bsf/bsr instructions to emulate_2op_SrcV_nobyte()
KVM: VMX: unlike vmcs on fail path
KVM: PPC: Emulator: clean up SPR reads and writes
KVM: PPC: Emulator: clean up instruction parsing
kvm/powerpc: Add new ioctl to retreive server MMU infos
kvm/book3s: Make kernel emulated H_PUT_TCE available for "PR" KVM
KVM: PPC: bookehv: Fix r8/r13 storing in level exception handler
KVM: PPC: Book3S: Enable IRQs during exit handling
KVM: PPC: Fix PR KVM on POWER7 bare metal
KVM: PPC: Fix stbux emulation
KVM: PPC: bookehv: Use lwz/stw instead of PPC_LL/PPC_STL for 32-bit fields
...
* Extend the APIC ops implementation and add IRQ_WORKER vector support so that 'perf' can work properly.
* Fix self-ballooning code, and balloon logic when booting as initial domain.
* Move array printing code to generic debugfs
* Support XenBus domains.
* Lazily free grants when a domain is dead/non-existent.
* In M2P code use batching calls
Bug-fixes:
* Fix NULL dereference in allocation failure path (hvc_xen)
* Fix unbinding of IRQ_WORKER vector during vCPU hot-unplug
* Fix HVM guest resume - we would leak an PIRQ value instead of reusing the existing one.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPu9MpAAoJEFjIrFwIi8fJaNQH/RylThiO+O+LBpPrO8VRUw+2
/Io98T7ZK2ggoUeaJx0C8irM0JMFAkxGMcfX3w9fwNt/BTec4s++4JhbN1jYN0da
6a0PqINo+M8y73So6CBfuJDCunaRLGKVG/ibIO3Y3WAff51/H+DMvO7uYYDAE0aA
mikyOxnaty0DiG5i4JGDHGmCzDASfK/jgGccZ03m6522mDx5ZIbTzZWONLfz8dqT
rbxnn9vrNLgEYWuzyLMwW0GymToUtt01xBQvwJLAbhn8lr1WBRBLpxXA+5iYNQrn
Ri25G7keYJhG4uwZfaHnR+4HTrmhlGzK1Z96dkqpGUaeIcdyWmPMp22VtBBiwG8=
=uyRr
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.5-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen updates from Konrad Rzeszutek Wilk:
"Features:
* Extend the APIC ops implementation and add IRQ_WORKER vector
support so that 'perf' can work properly.
* Fix self-ballooning code, and balloon logic when booting as initial
domain.
* Move array printing code to generic debugfs
* Support XenBus domains.
* Lazily free grants when a domain is dead/non-existent.
* In M2P code use batching calls
Bug-fixes:
* Fix NULL dereference in allocation failure path (hvc_xen)
* Fix unbinding of IRQ_WORKER vector during vCPU hot-unplug
* Fix HVM guest resume - we would leak an PIRQ value instead of
reusing the existing one."
Fix up add-add onflicts in arch/x86/xen/enlighten.c due to addition of
apic ipi interface next to the new apic_id functions.
* tag 'stable/for-linus-3.5-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: do not map the same GSI twice in PVHVM guests.
hvc_xen: NULL dereference on allocation failure
xen: Add selfballoning memory reservation tunable.
xenbus: Add support for xenbus backend in stub domain
xen/smp: unbind irqworkX when unplugging vCPUs.
xen: enter/exit lazy_mmu_mode around m2p_override calls
xen/acpi/sleep: Enable ACPI sleep via the __acpi_os_prepare_sleep
xen: implement IRQ_WORK_VECTOR handler
xen: implement apic ipi interface
xen/setup: update VA mapping when releasing memory during setup
xen/setup: Combine the two hypercall functions - since they are quite similar.
xen/setup: Populate freed MFNs from non-RAM E820 entries and gaps to E820 RAM
xen/setup: Only print "Freeing XXX-YYY pfn range: Z pages freed" if Z > 0
xen/gnttab: add deferred freeing logic
debugfs: Add support to print u32 array in debugfs
xen/p2m: An early bootup variant of set_phys_to_machine
xen/p2m: Collapse early_alloc_p2m_middle redundant checks.
xen/p2m: Allow alloc_p2m_middle to call reserve_brk depending on argument
xen/p2m: Move code around to allow for better re-usage.
Pull sparc changes from David S. Miller:
"This has the generic strncpy_from_user() implementation architectures
can now use, which we've been developing on linux-arch over the past
few days.
For good measure I ran both a 32-bit and a 64-bit glibc testsuite run,
and the latter of which pointed out an adjustment I needed to make to
sparc's user_addr_max() definition. Linus, you were right, STACK_TOP
was not the right thing to use, even on sparc itself :-)
From Sam Ravnborg, we have a conversion of sparc32 over to the common
alloc_thread_info_node(), since the aspect which originally blocked
our doing so (sun4c) has been removed."
Fix up trivial arch/sparc/Kconfig and lib/Makefile conflicts.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Fix user_addr_max() definition.
lib: Sparc's strncpy_from_user is generic enough, move under lib/
kernel: Move REPEAT_BYTE definition into linux/kernel.h
sparc: Increase portability of strncpy_from_user() implementation.
sparc: Optimize strncpy_from_user() zero byte search.
sparc: Add full proper error handling to strncpy_from_user().
sparc32: use the common implementation of alloc_thread_info_node()
Pull more relocation fixes from Peter Anvin:
"These are additional symbols that have been found to either be
absolute or look like they might end up being absolute on one version
of GNU ld or another. Unfortunately we have since that a different
GNU ld version, 2.21, can generate bogus absolute symbols; again, this
would have caused a malfunctioning kernel on x86-32 if relocated.
The relocs.c changes changed silent corruption to a build time error.
It is worth noting that if the various barrier symbols we use were
more consistent in the namespace used this probably could be reduced
to a single regexp; if nothing else it looks like there is migration
toward a common __(start|stop)___.* namespace."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, relocs: Add jiffies and jiffies_64 to the relative whitelist
x86-32, relocs: Whitelist more symbols for ld bug workaround
Lots of gpio changes, both to core code and drivers. Changes do touch
architecture code to remove the need for separate arm/gpio.h includes
in most architectures. Some new drivers are added, and a number of
gpio drivers are converted to use irq_domains for gpio inputs used as
interrupts. Device tree support has been amended to allow multiple
gpio_chips to use the same device tree node. Remaining changes are
primarily bug fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=U6hj
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO driver changes from Grant Likely:
"Lots of gpio changes, both to core code and drivers.
Changes do touch architecture code to remove the need for separate
arm/gpio.h includes in most architectures.
Some new drivers are added, and a number of gpio drivers are converted
to use irq_domains for gpio inputs used as interrupts. Device tree
support has been amended to allow multiple gpio_chips to use the same
device tree node.
Remaining changes are primarily bug fixes."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (33 commits)
gpio/generic: initialize basic_mmio_gpio shadow variables properly
gpiolib: Remove 'const' from data argument of gpiochip_find()
gpio/rc5t583: add gpio driver for RICOH PMIC RC5T583
gpiolib: quiet gpiochip_add boot message noise
gpio: mpc8xxx: Prevent NULL pointer deref in demux handler
gpio/lpc32xx: Add device tree support
gpio: Adjust of_xlate API to support multiple GPIO chips
gpiolib: Implement devm_gpio_request_one()
gpio-mcp23s08: dbg_show: fix pullup configuration display
Add support for TCA6424A
gpio/omap: (re)fix wakeups on level-triggered GPIOs
gpio/omap: fix broken context restore for non-OFF mode transitions
gpio/omap: fix missing check in *_runtime_suspend()
gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()
gpio/omap: remove suspend/resume callbacks
gpio/omap: remove retrigger variable in gpio_irq_handler
gpio/omap: remove saved_wakeup field from struct gpio_bank
gpio/omap: remove suspend_wakeup field from struct gpio_bank
gpio/omap: remove saved_fallingdetect, saved_risingdetect
gpio/omap: remove virtual_irq_start variable
...
Conflicts:
drivers/gpio/gpio-samsung.c
Pull alpha updates from Matt Turner:
"This pull adds the implementations of some Tru64 syscalls which allow
some proprietary software such as the C compiler to work on Linux.
Also, it adds some big-endian ioread functions to help us get closer
to building allyesconfig."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: add io{read,write}{16,32}be functions
alpha: implement various OSF/1 stat syscalls
alpha: implement setsysinfo(SSI_LMF) as a no-op
We need to use TASK_SIZE because for 64-bit tasks the value
of STACK_TOP actually sits in the middle of the address space
so we'll get false-negatives.
Adjust the TASK_SIZE definition on sparc64 to accomodate this,
in the context in which user_addr_max() is used we have the
test_thread_flag() definition available but not the one for
test_tsk_thread_flag().
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer updates from Thomas Gleixner.
Various trivial conflict fixups in arch Kconfig due to addition of
unrelated entries nearby. And one slightly more subtle one for sparc32
(new user of GENERIC_CLOCKEVENTS), fixed up as per Thomas.
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
timekeeping: Fix a few minor newline issues.
time: remove obsolete declaration
ntp: Fix a stale comment and a few stray newlines.
ntp: Correct TAI offset during leap second
timers: Fixup the Kconfig consolidation fallout
x86: Use generic time config
unicore32: Use generic time config
um: Use generic time config
tile: Use generic time config
sparc: Use: generic time config
sh: Use generic time config
score: Use generic time config
s390: Use generic time config
openrisc: Use generic time config
powerpc: Use generic time config
mn10300: Use generic time config
mips: Use generic time config
microblaze: Use generic time config
m68k: Use generic time config
m32r: Use generic time config
...
To use this, an architecture simply needs to:
1) Provide a user_addr_max() implementation via asm/uaccess.h
2) Add "select GENERIC_STRNCPY_FROM_USER" to their arch Kcnfig
3) Remove the existing strncpy_from_user() implementation and symbol
exports their architecture had.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: David Howells <dhowells@redhat.com>
Hide details of maximum user address calculation in a new
asm/uaccess.h interface named user_addr_max().
Provide little-endian implementation in find_zero(), which should work
but can probably be improved.
Abstrace alignment check behind IS_UNALIGNED() macro.
Kill double-semicolon, noticed by David Howells.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull main drm updates from Dave Airlie:
"This is the main merge window request for the drm.
It's big, but jam packed will lots of features and of course 0
regressions. (okay maybe there'll be one).
Highlights:
- new KMS drivers for server GPU chipsets: ast, mgag200 and cirrus
(qemu only). These drivers use the generic modesetting drivers.
- initial prime/dma-buf support for i915, nouveau, radeon, udl and
exynos
- switcheroo audio support: so GPUs with HDMI can turn off the sound
driver without crashing stuff.
- There are some patches drifting outside drivers/gpu into x86 and
EFI for better handling of multiple video adapters in Apple Macs,
they've got correct acks except one trivial fixup.
- Core:
edid parser has better DMT and reduced blanking support,
crtc properties,
plane properties,
- Drivers:
exynos: add 2D core accel support, prime support, hdmi features
intel: more Haswell support, initial Valleyview support, more
hdmi infoframe fixes, update MAINTAINERS for Daniel, lots of
cleanups and fixes
radeon: more HDMI audio support, improved GPU lockup recovery
support, remove nested mutexes, less memory copying on PCIE, fix
bus master enable race (kexec), improved fence handling
gma500: cleanups, 1080p support, acpi fixes
nouveau: better nva3 memory reclocking, kepler accel (needs
external firmware rip), async buffer moves on nv84+ hw.
I've some more dma-buf patches that rely on the dma-buf merge for vmap
stuff, and I've a few fixes building up, but I'd decided I'd better
get rid of the main pull sooner rather than later, so the audio guys
are also unblocked."
Fix up trivial conflict due to some duplicated changes in
drivers/gpu/drm/i915/intel_ringbuffer.c
* 'drm-core-next' of git://people.freedesktop.org/~airlied/linux: (605 commits)
drm/nouveau/nvd9: Fix GPIO initialisation sequence.
drm/nouveau: Unregister switcheroo client on exit
drm/nouveau: Check dsm on switcheroo unregister
drm/nouveau: fix a minor annoyance in an output string
drm/nouveau: turn a BUG into a WARN
drm/nv50: decode PGRAPH DATA_ERROR = 0x24
drm/nouveau/disp: fix dithering not being enabled on some eDP macbooks
drm/nvd9/copy: initialise copy engine, seems to work like nvc0
drm/nvc0/ttm: use copy engines for async buffer moves
drm/nva3/ttm: use copy engine for async buffer moves
drm/nv98/ttm: add in a (disabled) crypto engine buffer copy method
drm/nv84/ttm: use crypto engine for async buffer copies
drm/nouveau/ttm: untangle code to support accelerated buffer moves
drm/nouveau/fbcon: use fence for sync, rather than notifier
drm/nv98/crypt: non-stub implementation of the engine hooks
drm/nouveau/fifo: turn all fifo modules into engine modules
drm/nv50/graph: remove ability to do interrupt-driven context switching
drm/nv50: remove manual context unload on context destruction
drm/nv50: remove execution engine context saves on suspend
drm/nv50/fifo: use hardware channel kickoff functionality
...
Pull more networking updates from David Miller:
"Ok, everything from here on out will be bug fixes."
1) One final sync of wireless and bluetooth stuff from John Linville.
These changes have all been in his tree for more than a week, and
therefore have had the necessary -next exposure. John was just away
on a trip and didn't have a change to send the pull request until a
day or two ago.
2) Put back some defines in user exposed header file areas that were
removed during the tokenring purge. From Stephen Hemminger and Paul
Gortmaker.
3) A bug fix for UDP hash table allocation got lost in the pile due to
one of those "you got it.. no I've got it.." situations. :-)
From Tim Bird.
4) SKB coalescing in TCP needs to have stricter checks, otherwise we'll
try to coalesce overlapping frags and crash. Fix from Eric Dumazet.
5) RCU routing table lookups can race with free_fib_info(), causing
crashes when we deref the device pointers in the route. Fix by
releasing the net device in the RCU callback. From Yanmin Zhang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (293 commits)
tcp: take care of overlaps in tcp_try_coalesce()
ipv4: fix the rcu race between free_fib_info and ip_route_output_slow
mm: add a low limit to alloc_large_system_hash
ipx: restore token ring define to include/linux/ipx.h
if: restore token ring ARP type to header
xen: do not disable netfront in dom0
phy/micrel: Fix ID of KSZ9021
mISDN: Add X-Tensions USB ISDN TA XC-525
gianfar:don't add FCB length to hard_header_len
Bluetooth: Report proper error number in disconnection
Bluetooth: Create flags for bt_sk()
Bluetooth: report the right security level in getsockopt
Bluetooth: Lock the L2CAP channel when sending
Bluetooth: Restore locking semantics when looking up L2CAP channels
Bluetooth: Fix a redundant and problematic incoming MTU check
Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C
Bluetooth: Fix EIR data generation for mgmt_device_found
Bluetooth: Fix Inquiry with RSSI event mask
Bluetooth: improve readability of l2cap_seq_list code
Bluetooth: Fix skb length calculation
...
