Impact: fix system hang on some systems operating with HZ_1000
On a system that stalled with HZ_1000, the first value written to
T0_CMP (when the main counter was not stopped) did not trigger an
interrupt. Instead after the main counter wrapped around (after
several minutes) an interrupt was triggered and afterwards the
periodic interrupt took effect.
This can be fixed by implementing HPET spec recommendation for
programming the periodic mode (i.e. stopping the main counter).
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Mark Hounschell <markh@compro.net>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, vm86: fix preemption bug
x86, olpc: fix model detection without OFW
x86, hpet: fix for LS21 + HPET = boot hang
x86: CPA avoid repeated lazy mmu flush
x86: warn if arch_flush_lazy_mmu_cpu is called in preemptible context
x86/paravirt: make arch_flush_lazy_mmu/cpu disable preemption
x86, pat: fix warn_on_once() while mapping 0-1MB range with /dev/mem
x86/cpa: make sure cpa is safe to call in lazy mmu mode
x86, ptrace, mm: fix double-free on race
Between 2.6.23 and 2.6.24-rc1 a change was made that broke IBM LS21
systems that had the HPET enabled in the BIOS, resulting in boot hangs
for x86_64.
Specifically commit b8ce335906, which
merges the i386 and x86_64 HPET code.
Prior to this commit, when we setup the HPET timers in x86_64, we did
the following:
hpet_writel(HPET_TN_ENABLE | HPET_TN_PERIODIC | HPET_TN_SETVAL |
HPET_TN_32BIT, HPET_T0_CFG);
However after the i386/x86_64 HPET merge, we do the following:
cfg = hpet_readl(HPET_Tn_CFG(timer));
cfg |= HPET_TN_ENABLE | HPET_TN_PERIODIC |
HPET_TN_SETVAL | HPET_TN_32BIT;
hpet_writel(cfg, HPET_Tn_CFG(timer));
However on LS21s with HPET enabled in the BIOS, the HPET_T0_CFG register
boots with Level triggered interrupts (HPET_TN_LEVEL) enabled. This
causes the periodic interrupt to be not so periodic, and that results in
the boot time hang I reported earlier in the delay calibration.
My fix: Always disable HPET_TN_LEVEL when setting up periodic mode.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Implement Linus's suggestion: introduce the hpet_cnt_ahead()
helper function to compare hpet time values - like other
wrapping counter comparisons are abstracted away elsewhere.
(jiffies, ktime_t, etc.)
Reported-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There's a small problem with hpet_rtc_reinit function - it checks
for the:
hpet_readl(HPET_COUNTER) - hpet_t1_cmp > 0
to continue increasing both the HPET_T1_CMP (register) and the
hpet_t1_cmp (variable).
But since the HPET_COUNTER is always 32-bit, if the hpet_t1_cmp
is 64-bit this condition will always be FALSE once the latter hits
the 32-bit boundary, and we can have a situation, when we don't
increase the HPET_T1_CMP register high enough.
The result - timer stops ticking, since HPET_T1_CMP becomes less,
than the COUNTER and never increased again.
The solution is (based on Linus's suggestion) to not compare 64-bits
(on 64-bit x86), but to do the comparison on 32-bit signed
integers.
Reported-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: Fix debugobjects warning
debugobject enabled kernels spit out a warning in hpet code due to a
workqueue which is initialized on stack.
Add INIT_WORK_ON_STACK() which calls init_timer_on_stack() and use it
in hpet.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
hrtimers: fix warning in kernel/hrtimer.c
x86: make sure we really have an hpet mapping before using it
x86: enable HPET on Fujitsu u9200
linux/timex.h: cleanup for userspace
posix-timers: simplify de_thread()->exit_itimers() path
posix-timers: check ->it_signal instead of ->it_pid to validate the timer
posix-timers: use "struct pid*" instead of "struct task_struct*"
nohz: suppress needless timer reprogramming
clocksource, acpi_pm.c: put acpi_pm_read_slow() under CONFIG_PCI
nohz: no softirq pending warnings for offline cpus
hrtimer: removing all ur callback modes, fix
hrtimer: removing all ur callback modes, fix hotplug
hrtimer: removing all ur callback modes
x86: correct link to HPET timer specification
rtc-cmos: export second NVRAM bank
Fixed up conflicts in sound/drivers/pcsp/pcsp.c and sound/core/hrtimer.c
manually.
Impact: prepare the hpet code for Xen dom0 booting
When booting in Xen dom0, the hpet isn't really accessible, so make
sure the mapping is non-NULL before use.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: auto-enable HPET on Fujitsu u9200
HPET timer is listed in the ACPI table, but needs a quirk entry in order to
work. Unfortunately, the quirk code runs after first HPET hpet_enable() which
has already determined that the timer doesn't work (reads 0xFFFFFFFF). This
patch allows hpet_enable() to be called again after running the quirk code.
Signed-off-by: Janne Kulmala <janne.t.kulmala@tut.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Impact: change existing irq_chip API
Not much point with gentle transition here: the struct irq_chip's
setaffinity method signature needs to change.
Fortunately, not widely used code, but hits a few architectures.
Note: In irq_select_affinity() I save a temporary in by mangling
irq_desc[irq].affinity directly. Ingo, does this break anything?
(Folded in fix from KOSAKI Motohiro)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Ingo Molnar <mingo@redhat.com>
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: jeremy@xensource.com
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Impact: fix build warning
this warning:
arch/x86/kernel/hpet.c:36: warning: ‘hpet_num_timers’ defined but not used
Triggers because hpet_num_timers is unused in the !CONFIG_PCI_MSI case.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: make global variable static
Fix this sparse warning:
arch/x86/kernel/hpet.c:36:18: warning: symbol 'hpet_num_timers' was
not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some functions that may be called from this handler require that
interrupts are disabled. Also, combining IRQF_DISABLED and
IRQF_SHARED does not reliably disable interrupts in a handler, so
remove IRQF_SHARED from the irq flags (this irq is not shared anyway).
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Cc: mingo@elte.hu
Cc: venkatesh.pallipadi@intel.com
Cc: "Will Newton" <will.newton@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In hpet_next_event() we check that the value we just wrote to
HPET_Tn_CMP(timer) has reached the chip. Currently, we're checking that
the value we wrote to HPET_Tn_CMP(timer) is in HPET_T0_CMP, which, if
timer is anything other than timer 0, is likely to fail.
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Cc: mingo@elte.hu
Cc: venkatesh.pallipadi@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It is possible to flood the console with call traces if the WARN_ON
condition is true because of the frequency with which this function is
called.
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Cc: mingo@elte.hu
Cc: venkatesh.pallipadi@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix the below compile warnings due to recent HPET MSI changes
arch/x86/kernel/hpet.c:48: warning: 'hpet_devs' defined but not used
arch/x86/kernel/hpet.c:50: warning: 'per_cpu__cpu_hpet_dev' defined but not used
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Initialize a per CPU HPET MSI timer when possible. We retain the HPET
timer 0 (IRQ 0) and timer 1 (IRQ 8) as is when legacy mode is being used. We
setup the remaining HPET timers as per CPU MSI based timers. This per CPU
timer will eliminate the need for timer broadcasting with IRQ 0 when there
is non-functional LAPIC timer across CPU deep C-states.
If there are more CPUs than number of available timers, CPUs that do not
find any timer to use will continue using LAPIC and IRQ 0 broadcast.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Preparatory patch before the actual HPET MSI changes. Sets up hpet_set_mode
and hpet_next_event for the MSI related changes. Just the code
refactoring and should be zero functional change.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
After fixing the u32 thinko I sill had occasional hickups on ATI chipsets
with small deltas. There seems to be a delay between writing the compare
register and the transffer to the internal register which triggers the
interrupt. Reading back the value makes sure, that it hit the internal
match register befor we compare against the counter value.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We use the HPET only in 32bit mode because:
1) some HPETs are 32bit only
2) on i386 there is no way to read/write the HPET atomic 64bit wide
The HPET code unification done by the "moron of the year" did
not take into account that unsigned long is different on 32 and
64 bit.
This thinko results in a possible endless loop in the clockevents
code, when the return comparison fails due to the 64bit/332bit
unawareness.
unsigned long cnt = (u32) hpet_read() + delta can wrap over 32bit.
but the final compare will fail and return -ETIME causing endless
loops.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The minimum reprogramming delta was hardcoded in HPET ticks,
which is stupid as it does not work with faster running HPETs.
The C1E idle patches made this prominent on AMD/RS690 chipsets,
where the HPET runs with 25MHz. Set it to 5us which seems to be
a reasonable value and fixes the problems on the bug reporters
machines. We have a further sanity check now in the clock events,
which increases the delta when it is not sufficient.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Tested-by: Dmitry Nezhevenko <dion@inhex.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
AMD SB700 based systems with spread spectrum enabled use a SMM based
HPET emulation to provide proper frequency setting. The SMM code is
initialized with the first HPET register access and takes some time to
complete. During this time the config register reads 0xffffffff. We
check for max. 1000 loops whether the config register reads a non
0xffffffff value to make sure that HPET is up and running before we go
further. A counting loop is safe, as the HPET access takes thousands
of CPU cycles. On non SB700 based machines this check is only done
once and has no side effects.
Based on a quirk patch from: crane cai <crane.cai@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Minor /dev/hpet updates and bugfixes:
* Remove dead code, mostly remnants of an incomplete/unusable
kernel interface ... noted when addressing "sparse" warnings:
+ hpet_unregister() and a routine it calls
+ hpet_task and all references, including hpet_task_lock
+ hpet_data.hd_flags (and HPET_DATA_PLATFORM)
* Correct and improve boot message:
+ displays *counter* (shared between comparators) bit width,
not *timer* bit widths (which are often mixed)
+ relabel "timers" as "comparators"; this is less confusing,
they are not independent like normal timers are (sigh)
+ display MHz not Hz; it's never less than 10 MHz.
* Tighten and correct the userspace interface code
+ don't accidentally program comparators in 64-bit mode using
32-bit values ... always force comparators into 32-bit mode
+ provide the correct bit definition flagging comparators with
periodic capability ... the ABI is unchanged
* Update Documentation/hpet.txt
+ be more correct and current
+ expand description a bit
+ don't mention that now-gone kernel interface
Plus, add a FIXME comment for something that could cause big trouble
on systems with more capable HPETs than at least Intel seems to ship.
It seems that few folk use this userspace interface; it's not very
usable given the general lack of HPET IRQ routing. I'm told that
the only real point of it any more is to mmap for fast timestamps;
IMO that's handled better through the gettimeofday() vsyscall.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This fixes kernel http://bugzilla.kernel.org/show_bug.cgi?id=11112 (bogus
RTC update IRQs reported) for rtc-cmos, in two ways:
- When HPET is stealing the IRQs, use the first IRQ to grab
the seconds counter which will be monitored (instead of
using whatever was previously in that memory);
- In sane IRQ handling modes, scrub out old IRQ status before
enabling IRQs.
That latter is done by tightening up IRQ handling for rtc-cmos everywhere,
also ensuring that when HPET is used it's the only thing triggering IRQ
reports to userspace; net object shrink.
Also fix a bogus HPET message related to its RTC emulation.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Report-by: W Unruh <unruh@physics.ubc.ca>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While reading through the HPET code I realized that the
computation of .mult variables could be done with less
lines of code, resulting in a 1.6% text size saving
for hpet.o
So I propose the following patch, which applies against
today's Linus -git tree.
>From 0c6507e400e9ca5f7f14331e18f8c12baf75a9d3 Mon Sep 17 00:00:00 2001
From: Carlos R. Mafra <crmafra@ift.unesp.br>
Date: Mon, 5 May 2008 19:38:53 -0300
The computation of clocksource_hpet.mult
tmp = (u64)hpet_period << HPET_SHIFT;
do_div(tmp, FSEC_PER_NSEC);
clocksource_hpet.mult = (u32)tmp;
can be streamlined if we note that it is equal to
clocksource_hpet.mult = div_sc(hpet_period, FSEC_PER_NSEC, HPET_SHIFT);
Furthermore, the computation of hpet_clockevent.mult
uint64_t hpet_freq;
hpet_freq = 1000000000000000ULL;
do_div(hpet_freq, hpet_period);
hpet_clockevent.mult = div_sc((unsigned long) hpet_freq,
NSEC_PER_SEC, hpet_clockevent.shift);
can also be streamlined with the observation that hpet_period and hpet_freq are
inverse to each other (in proper units).
So instead of computing hpet_freq and using (schematically)
div_sc(hpet_freq, 10^9, shift) we use the trick of calling with the
arguments in reverse order, div_sc(10^6, hpet_period, shift).
The different power of ten is due to frequency being in Hertz (1/sec)
and the period being in units of femtosecond. Explicitly,
mult = (hpet_freq * 2^shift)/10^9 (before)
mult = (10^6 * 2^shift)/hpet_period (after)
because hpet_freq = 10^15/hpet_period.
The comments in the code are also updated to reflect the changes.
As a result,
text data bss dec hex filename
2957 425 92 3474 d92 arch/x86/kernel/hpet.o
3006 425 92 3523 dc3 arch/x86/kernel/hpet.o.old
a 1.6% reduction in text size.
Signed-off-by: Carlos R. Mafra <crmafra@ift.unesp.br>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Al Viro pointed out that there's a missing readl() of timer->hpet_config,
found by Sparse.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove the magic number in the third argment of div_sc().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The commits:
commit 37a47db8d7
Author: Balaji Rao <balajirrao@gmail.com>
Date: Wed Jan 30 13:30:03 2008 +0100
x86: assign IRQs to HPET timers, fix
and
commit e3f37a54f6
Author: Balaji Rao <balajirrao@gmail.com>
Date: Wed Jan 30 13:30:03 2008 +0100
x86: assign IRQs to HPET timers
have been identified to cause a regression on some platforms due to
the assignement of legacy IRQs which makes the legacy devices
connected to those IRQs disfunctional.
Revert them.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=10382
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
the previous patch in the old RTC driver. It also removes the direct
rtc_interrupt() call from arch/x86/kernel/hpetc.c so that there's finally no
(code) dependency to CONFIG_RTC in arch/x86/kernel/hpet.c.
Because of this, it's possible to compile the drivers/char/rtc.ko driver as
module and still use the HPET emulation functionality. This is also expressed
in Kconfig.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Robert Picco <Robert.Picco@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
enabled, then interrupts don't work for the rtc-cmos driver which results in
RTC_AIE*, RTC_PIE* and RTC_ALM being unusable. This affects hwclock from
util-linux-ng at least on i386 since that uses RTC_PIE_ON. (For x86-64, a
polling method is used for unknown reasons.)
This patch series now
1. export the functions from arch/x86/kernel/hpet.c that the old char/rtc
driver uses to work around that problem,
2. makes it possible to compile the old rtc driver as module, while still
having CONFIG_HPET_EMULATE_RTC enabled and
3. makes use of the exported functions in (1) in the new rtc-cmos driver.
This patch:
This patch makes the RTC emulation functions in arch/x86/kernel/hpet.c usable
for kernel modules. It
- exports the functions (EXPORT_SYMBOL_GPL()),
- adds an interface to register the interrupt callback function
instead of using only a fixed callback function and
- replaces the rtc_get_rtc_time() function which depends on
CONFIG_RTC with a call to get_rtc_time() which is defined in
include/asm-generic/rtc.h.
The only dependency to CONFIG_RTC is the call to rtc_interrupt() which is
removed by the next patch. After this, there's no (code) dependency of
this functions to CONFIG_RTC=y any more.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Robert Picco <Robert.Picco@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lucas Woods <woodzy@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Looks like IRQ 31 is assigned to timer 3, even without the patch!
I wonder who wrote the number 31. But the manual says that it is
zero by default.
I think we should check whether the timer has been allocated an IRQ before
proceeding to assign one to it. Here is a patch that does this.
Signed-off-by: Balaji Rao <balajirrao@gmail.com>
Tested-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The userspace API for the HPET (see Documentation/hpet.txt) did not work. The
HPET_IE_ON ioctl was failing as there was no IRQ assigned to the timer
device. This patch fixes it by allocating IRQs to timer blocks in the HPET.
arch/x86/kernel/hpet.c | 13 +++++--------
drivers/char/hpet.c | 45 ++++++++++++++++++++++++++++++++++++++-------
include/linux/hpet.h | 2 +-
3 files changed, 44 insertions(+), 16 deletions(-)
Signed-off-by: Balaji Rao <balajirrao@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
I was confused by FSEC = 10^15 NSEC statement, plus small whitespace
fixes. When there's copyright, there should be GPL.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In the current code, RTC_AIE doesn't work if the RTC relies on
CONFIG_HPET_EMULATE_RTC because the code sets the RTC_AIE flag in
hpet_set_rtc_irq_bit(). The interrupt handles does accidentally check
for RTC_PIE and not RTC_AIE when comparing the time which was set in
hpet_set_alarm_time().
I now verified on a test system here that without the patch applied,
the attached test program fails on a system that has HPET with
2.6.24-rc7-default. That's not critical since I guess the problem has
been there for several kernel releases, but as the fix is quite
obvious.
Configuration is CONFIG_RTC=y and CONFIG_HPET_EMULATE_RTC=y.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If HPET was enabled by pci quirks, we use i8253 as initial clockevent
because pci quirks doesn't run until pci is initialized.
The above means the kernel (or something) is assuming HPET legacy
replacement is disabled and can use i8253 at boot.
If we used kexec, it isn't true. So, this patch disables HPET legacy
replacement for kexec in machine_shutdown().
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (74 commits)
fix do_sys_open() prototype
sysfs: trivial: fix sysfs_create_file kerneldoc spelling mistake
Documentation: Fix typo in SubmitChecklist.
Typo: depricated -> deprecated
Add missing profile=kvm option to Documentation/kernel-parameters.txt
fix typo about TBI in e1000 comment
proc.txt: Add /proc/stat field
small documentation fixes
Fix compiler warning in smount example program from sharedsubtree.txt
docs/sysfs: add missing word to sysfs attribute explanation
documentation/ext3: grammar fixes
Documentation/java.txt: typo and grammar fixes
Documentation/filesystems/vfs.txt: typo fix
include/asm-*/system.h: remove unused set_rmb(), set_wmb() macros
trivial copy_data_pages() tidy up
Fix typo in arch/x86/kernel/tsc_32.c
file link fix for Pegasus USB net driver help
remove unused return within void return function
Typo fixes retrun -> return
x86 hpet.h: remove broken links
...
