We use a similar technique to ppc32: We set a thread local flag
to indicate that we are about to enter or have entered the stop
state, and have fixup code in the async interrupt entry code that
reacts to this flag to make us return to a different location
(sets NIP to LINK in our case).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
--
v2. Fix lockdep bug
Re-mask interrupts when coming back from idle
Enables support for HMC initiated partition hibernation. This is
a firmware assisted hibernation, since the firmware handles writing
the memory out to disk, along with other partition information,
so we just mimic suspend to ram.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the decrementer and timekeeping code was moved over to using
the generic clockevents and timekeeping infrastructure, several
variables and functions have been obsolete and effectively unused.
This deletes them.
In particular, wakeup_decrementer() is no longer needed since the
generic code reprograms the decrementer as part of the process of
resuming the timekeeping code, which happens during sysdev resume.
Thus the wakeup_decrementer calls in the suspend_enter methods for
52xx platforms have been removed. The call in the powermac cpu
frequency change code has been replaced by set_dec(1), which will
cause a timer interrupt as soon as interrupts are enabled, and the
generic code will then reprogram the decrementer with the correct
value.
This also simplifies the generic_suspend_en/disable_irqs functions
and makes them static since they are not referenced outside time.c.
The preempt_enable/disable calls are removed because the generic
code has disabled all but the boot cpu at the point where these
functions are called, so we can't be moved to another cpu.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Version 3 of this patch is updated with documentation added to
Documentation/ABI. There are no changes to any of the C code from v2
of the patch.
In order to support kernel DLPAR of CPU resources we need to provide an
interface to add (probe) and remove (release) the resource from the system.
This patch Creates new generic probe and release sysfs files to facilitate
cpu probe/release. The probe/release interface provides for allowing each
arch to supply their own routines for implementing the backend of adding
and removing cpus to/from the system.
This also creates the powerpc specific stubs to handle the arch callouts
from writes to the sysfs files.
The creation and use of these files is regulated by the
CONFIG_ARCH_CPU_PROBE_RELEASE option so that only architectures that need the
capability will have the files created.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some of the PCI features we have in ppc32 we will need on ppc64
platforms in the future. These include support for:
* ppc_md.pci_exclude_device
* indirect config cycles
* early config cycles
We also simplified the logic in fake_pci_bus() to assume it will always
get a valid pci_controller. Since all current callers seem to pass it
one.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The guts of do_IRQ() isn't really the right place to be documenting
the ppc_md.get_irq() interface. So move the comment into machdep.h
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds the necessary bits and pieces to powerpc implementation of
ioremap to benefit from caller tracking in /proc/vmallocinfo, at least
for ioremap's done after mem init as the older ones aren't tracked.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We essentially adopt the 64-bit dma code, with some changes to support
32-bit systems, including HIGHMEM. dma functions on 32-bit are now
invoked via accessor functions which call the correct op for a device based
on archdata dma_ops. If there is no archdata dma_ops, this defaults
to dma_direct_ops.
In addition, the dma_map/unmap_page functions are added to dma_ops
because we can't just fall back on map/unmap_single when HIGHMEM is
enabled. In the case of dma_direct_*, we stop using map/unmap_single
and just use the page version - this saves a lot of ugly
ifdeffing. We leave map/unmap_single in the dma_ops definition,
though, because they are needed by the iommu code, which does not
implement map/unmap_page. Ideally, going forward, we will completely
eliminate map/unmap_single and just have map/unmap_page, if it's
workable for 64-bit.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
from include/asm-powerpc. This is the result of a
mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-08-04 12:02:00 +10:00
Renamed from include/asm-powerpc/machdep.h (Browse further)
