* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (35 commits)
Input: wistron - add support for Acer TravelMate 2424NWXCi
Input: wistron - fix setting up special buttons
Input: add KEY_BLUETOOTH and KEY_WLAN definitions
Input: add new BUS_VIRTUAL bus type
Input: add driver for stowaway serial keyboards
Input: make input_register_handler() return error codes
Input: remove cruft that was needed for transition to sysfs
Input: fix input module refcounting
Input: constify input core
Input: libps2 - rearrange exports
Input: atkbd - support Microsoft Natural Elite Pro keyboards
Input: i8042 - disable MUX mode on Toshiba Equium A110
Input: i8042 - get rid of polling timer
Input: send key up events at disconnect
Input: constify psmouse driver
Input: i8042 - add Amoi to the MUX blacklist
Input: logips2pp - add sugnature 56 (Cordless MouseMan Wheel), cleanup
Input: add driver for Touchwin serial touchscreens
Input: add driver for Touchright serial touchscreens
Input: add driver for Penmount serial touchscreens
...
The key mappings are the same as the older Acer TravelMate 240.
Signed-off-by: Ashutosh Naik <ashutosh.naik@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If either wifi or bluetooth button has been detected, the code
would break off the loop. But there are laptops that have both
types of buttons, so the loop has to continue checking.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
ppc can boot one single binary on prep, chrp and pmac boards. ppc64 can
boot one single binary on pseries and G5 boards. pmac has no legacy io,
probing for PC style legacy hardware (or accessing the legacy io area
regulary) may lead to a hard crash:
* add check for parport_pc, exit on pmac. 32bit chrp has no
->check_legacy_ioport, the probe is always called. 64bit chrp has
check_legacy_ioport, check for a "parallel" node
* add check for isapnp, only PReP boards may have real ISA slots. 32bit
PReP will have no ->check_legacy_ioport, the probe is always called.
* update code in i8042_platform_init. Run ->check_legacy_ioport first,
always call request_region. No functional change. Remove whitespace
before i8042_reset init.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for keypad driver running on different TI
OMAP(http://www.ti.com/omap) processor based boards like OSK, H2, H3, H4,
Persuas and Nokia 770.
Signed-off-by: Komal Shah <komal_shah802003@yahoo.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds some simple PM stubs and the basic APM interfaces,
primarily for use by hp6xx, where the existing userland
expects it.
Signed-off-by: Andriy Skulysh <askulysh@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for stowaway and stowaway compatible (eg. dicota inutPDA)
serial keyboards. Reported to work on palm zire71 and palm tungsten T3.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Now that input_free_device is basically an alias for input_put_device
we need to acquire a reference to input module right when we allocate
device because input_dev_release releases reference to input module
unconditionally.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Microsoft Natural Elite Pro keyboard produces unisual response to
the GET ID command - single byte 0xaa (normally keyboards produce
2-byte response). Fail GET ID command so atkbd gets a change to
do alternate probe.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When keyboard controller is in active multiplexing mode ALPS touchpad
may get detected twice. Since the box does not have external PS/2
ports simply disabling MUX mode is safe solution.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove polling timer that was used to detect keybord/mice hotplug and
register both IRQs right away instead of waiting for a driver to
attach to a port.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Emit key up events for all pressed keys/buttons when disconnecting
an input device. Cures "stuck" enter key effect when unloading
keyboard module.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This was introduced in commit 3d0f0fa0cb:
bounds checking is performed against period[32] while indexing delay[4].
Spotted by Coverity, CID 1376.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
ALPS touchpad on Amoi laptops (Amoi is a vendor in China) is not
detected when keyboard controller is in MUX mode, add to blacklist.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- Use the touch status bit rather than the pressure bits to
distinguish a BTN_TOUCH event. Non-pressure-sensitive touchscreens
always report full pressure
- Report ABS_PRESSURE information only if the touchscreen supports it
Signed-off-by: Shaun Jackman <sjackman@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix 10-byte protocol checksum calculation and do not discard packet early
unless it is missing lead in byte.
Signed-off-by: Shaun Jackman <sjackman@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Trackpoint driver was not sending the magic knock sequence upon resume
causing incorrect device behavior after resuming from disk.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
MX300 does not have an EXTRA_BTN - it is a simple wheel mouse with
an additional task-switcher button, which is reported as side button
(and not task button).
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The userspace interface of the force feedback part is changed and
documentation in uinput.h is updated accordingly. MODULE_VERSION
is also incremented to reflect the revision.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Consolidate core implementing memoryless devices in one module; added
support for gain and envelopes and periodic => rumble conversion.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Implement a new force feedback interface, in which all non-driver-specific
operations are separated to a common module. This includes handling effect
type validations, locking, etc.
The effects are now file descriptor specific instead of the previous strange
half-process half-fd specific behaviour. The effect memory of devices is not
emptied if the root user opens and closes the device while another user is
using effects. This is a minor change and most likely no force feedback
aware programs are affected by this negatively.
Otherwise the userspace interface is left unaltered.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Move fixp-arith.h from drivers/usb/input to drivers/input, as the part of
force feedback support that requires trigonometric functions is being moved
there.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This will allow building input core module from several files
which is needed for the reworked force feedback support.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Although the Spaceball 4000FLX Lefty is already supported by the
spaceball driver, it does not register properly due to SPACEBALL_MAX_ID
being set too low. Increment SPACEBALL_MAX_ID such that the 4000FLX Lefty
is properly recognized.
Signed-off-by: Nick Martin <nim+linux@nimlabs.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The start() method need to be called every time we create
a new handle. This includes not only registering new devices
but also when registering new handlers.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Create input_inject_event() function which is to be used by input
handlers as opposed to input_event() which is reserved for drivers
implementing input devices. The difference is that if device is
"grabbed" by some process input_inject_event() will ignore events
unless sent from the handle that is currently owns the device.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
