Fix kernel-doc comments so that they don't produce errors.
Also cut some extraneous copy-paste text.
Error(linhead//drivers/pci/pci.c:1133): duplicate section name 'Description'
Error(linhead//drivers/pci/pci.c:1189): duplicate section name 'Description'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/pci/pci.c needs pm_wakeup.h since it uses device_set_wakup_capable().
The latter also needs to be stubbed out for !CONFIG_PM.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The recently introduced pci_prepare_to_sleep() needs the following fix,
because there are systems which are not power manageable by ACPI (ie.
ACPI doesn't provide methods to put the device into low power states and
back), but require ACPI hooks to be executed for wake-up to work.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If the offset of PCI device's PM capability in its configuration space,
the mask of states that the device supports PME# from and the D1 and D2
support bits are cached in the corresponding struct pci_dev, the PCI
device PM code can be simplified quite a bit.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce functions pci_prepare_to_sleep() and pci_back_from_sleep(),
to be used by the PCI drivers that want to place their devices into
the lowest power state appropiate for them (PCI_D3hot, if the device
is not supposed to wake up the system, or the deepest state from
which the wake-up is possible, otherwise) while the system is being
prepared to go into a sleeping state and to put them back into D0
during the subsequent transition to the working state.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* Introduce function acpi_pm_device_sleep_wake() for enabling and
disabling the system wake-up capability of devices that are power
manageable by ACPI.
* Introduce function acpi_bus_can_wakeup() allowing other (dependent)
subsystems to check if ACPI is able to enable the system wake-up
capability of given device.
* Introduce callback .sleep_wake() in struct pci_platform_pm_ops and
for the ACPI PCI 'driver' make it use acpi_pm_device_sleep_wake().
* Introduce callback .can_wakeup() in struct pci_platform_pm_ops and
for the ACPI 'driver' make it use acpi_bus_can_wakeup().
* Move the PME# handlig code out of pci_enable_wake() and split it
into two functions, pci_pme_capable() and pci_pme_active(),
allowing the caller to check if given device is capable of
generating PME# from given power state and to enable/disable the
device's PME# functionality, respectively.
* Modify pci_enable_wake() to use the new ACPI callbacks and the new
PME#-related functions.
* Drop the generic .platform_enable_wakeup() callback that is not
used any more.
* Introduce device_set_wakeup_capable() that will set the
power.can_wakeup flag of given device.
* Rework PCI device PM initialization so that, if given device is
capable of generating wake-up events, either natively through the
PME# mechanism, or with the help of the platform, its
power.can_wakeup flag is set and its power.should_wakeup flag is
unset as appropriate.
* Make ACPI set the power.can_wakeup flag for devices found to be
wake-up capable by it.
* Make the ACPI wake-up code enable/disable GPEs for devices that
have the wakeup.flags.prepared flag set (which means that their
wake-up power has been enabled).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Rework pci_set_power_state() so that the platform callback is
invoked before the native mechanism, if necessary. Also, make
the function check if the device is power manageable by the
platform before invoking the platform callback.
This may matter if the device dependent on additional power
resources controlled by the platform is being put into D0, in which
case those power resources must be turned on before we attempt to
handle the device itself.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce function pointer platform_pci_power_manageable to be used
by the platform-related code to point to a function allowing us to
check if given device is power manageable by the platform.
Introduce acpi_pci_power_manageable() playing that role for ACPI.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Convert printks to use dev_printk().
I converted pr_debug() to dev_dbg(). Both use KERN_DEBUG and are enabled
only when DEBUG is defined.
I converted printk(KERN_DEBUG) to dev_printk(KERN_DEBUG), not to dev_dbg(),
because dev_dbg() is only enabled when DEBUG is defined.
I converted DBG(KERN_INFO) (only in setup-bus.c) to dev_info(). The DBG()
name makes it sound like debug, but it's been enabled forever, so dev_info()
preserves the previous behavior.
I tried to make the resource assignment formats more consistent, e.g.,
"BAR %d: got res [%#llx-%#llx] bus [%#llx-%#llx] flags %#lx\n"
instead of sometimes using "start-end" and sometimes using "size@start".
I'm not attached to one or the other; I'd just like them consistent.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since the second argument of acpi_pci_choose_state() and
platform_pci_choose_state() is never used, remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI Express ASPM defines a protocol for PCI Express components in the D0
state to reduce Link power by placing their Links into a low power state
and instructing the other end of the Link to do likewise. This
capability allows hardware-autonomous, dynamic Link power reduction
beyond what is achievable by software-only controlled power management.
However, The device should be configured by software appropriately.
Enabling ASPM will save power, but will introduce device latency.
This patch adds ASPM support in Linux. It introduces a global policy for
ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control
it. The interface can be used as a boot option too. Currently we have
below setting:
-default, BIOS default setting
-powersave, highest power saving mode, enable all available ASPM
state and clock power management
-performance, highest performance, disable ASPM and clock power
management
By default, the 'default' policy is used currently.
In my test, power difference between powersave mode and performance mode
is about 1.3w in a system with 3 PCIE links.
Note: some devices might not work well with aspm, either because chipset
issue or device issue. The patch provide API (pci_disable_link_state),
driver can disable ASPM for specific device.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Revert as it is reported to cause problems for people.
commit 4348a2dc49
Author: Shaohua Li <shaohua.li@intel.com>
Date: Wed Oct 24 10:45:08 2007 +0800
pcie: utilize pcie transaction pending bit
PCIE has a mechanism to wait for Non-Posted request to complete. I think
pci_disable_device is a good place to do this.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to the regression reported at
http://bugzilla.kernel.org/show_bug.cgi?id=10065
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Soeren Sonnenburg <kernel@nn7.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During the last step of hibernation in the "platform" mode (with the
help of ACPI) we use the suspend code, including the devices'
->suspend() methods, to prepare the system for entering the ACPI S4
system sleep state.
But at least for some devices the operations performed by the
->suspend() callback in that case must be different from its operations
during regular suspend.
For this reason, introduce the new PM event type PM_EVENT_HIBERNATE and
pass it to the device drivers' ->suspend() methods during the last phase
of hibernation, so that they can distinguish this case and handle it as
appropriate. Modify the drivers that handle PM_EVENT_SUSPEND in a
special way and need to handle PM_EVENT_HIBERNATE in the same way.
These changes are necessary to fix a hibernation regression related
to the i915 driver (ref. http://lkml.org/lkml/2008/2/22/488).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds PCI's accessor for segment_boundary_mask in device_dma_parameters.
The default segment_boundary is set to 0xffffffff, same to the block layer's
default value (and the scsi mid layer uses the same value).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds struct device_dma_parameters in struct pci_dev and properly
sets up a pointer in struct device.
The default max_segment_size is set to 64K, same to the block layer's
default value.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Mostly-acked-by: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 6c723d5bd8.
It caused build errors on non-x86 platforms, config file confusion, and
even some boot errors on some x86-64 boxes. All around, not quite ready
for prime-time :(
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6: (64 commits)
PCI: make pci_bus a struct device
PCI: fix codingstyle issues in include/linux/pci.h
PCI: fix codingstyle issues in drivers/pci/pci.h
PCI: PCIE ASPM support
PCI: Fix fakephp deadlock
PCI: modify SB700 SATA MSI quirk
PCI: Run ACPI _OSC method on root bridges only
PCI ACPI: AER driver should only register PCIe devices with _OSC
PCI ACPI: Added a function to register _OSC with only PCIe devices.
PCI: constify function pointer tables
PCI: Convert drivers/pci/proc.c to use unlocked_ioctl
pciehp: block new requests from the device before power off
pciehp: workaround against Bad DLLP during power off
pciehp: wait for 1000ms before LED operation after power off
PCI: Remove pci_enable_device_bars() from documentation
PCI: Remove pci_enable_device_bars()
PCI: Remove users of pci_enable_device_bars()
PCI: Add pci_enable_device_{io,mem} intefaces
PCI: avoid save the same type of cap multiple times
PCI: correctly initialize a structure for pcie_save_pcix_state()
...
PCI Express ASPM defines a protocol for PCI Express components in the D0
state to reduce Link power by placing their Links into a low power state
and instructing the other end of the Link to do likewise. This
capability allows hardware-autonomous, dynamic Link power reduction
beyond what is achievable by software-only controlled power management.
However, The device should be configured by software appropriately.
Enabling ASPM will save power, but will introduce device latency.
This patch adds ASPM support in Linux. It introduces a global policy for
ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control
it. The interface can be used as a boot option too. Currently we have
below setting:
-default, BIOS default setting
-powersave, highest power saving mode, enable all available ASPM
state
and clock power management
-performance, highest performance, disable ASPM and clock power
management
By default, the 'default' policy is used currently.
In my test, power difference between powersave mode and performance mode
is about 1.3w in a system with 3 PCIE links.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that all in-tree users are gone, this removes pci_enable_device_bars()
completely.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pci_enable_device_bars() interface isn't well suited to PCI
because you can't actually enable/disable BARs individually on
a device. So for example, if a device has 2 memory BARs 0 and 1,
and one of them (let's say 1) has not been successfully allocated
by the firmware or the kernel, then enabling memory decoding
shouldn't be permitted for the entire device since it will decode
whatever random address is still in that BAR 1.
So a device must be either fully enabled for IO, for Memory, or
for both. Not on a per-BAR basis.
This provides two new functions, pci_enable_device_io() and
pci_enable_device_mem() to replace pci_enable_device_bars(). The
implementation internally builds a BAR mask in order to be able
to use existing arch infrastructure.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Avoid adding the same type of cap multiple times, otherwise we will see dead loop.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
save_state->cap_nr should be correctly set, otherwise we can't find the
saved cap at resume.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pci_save/store_state has multiple bugs, which will cause cap can't be
saved/restored correctly. Below 3 patches fix them.
fix the typo in pci_save_pcix_state
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCIE has a mechanism to wait for Non-Posted request to complete. I think
pci_disable_device is a good place to do this.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the needlessly global pci_restore_bars() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's no reason not to allow multiple calls to pcim_enable_device().
Calls after the first one can simply be noop. All PCI resources will
be released when the initial pcim_enable_device() resource is
released.
This allows more flexibility to managed PCI users.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Introduce pci_domains_supported global, hardcoded to zero if
!CONFIG_PCI_DOMAINS.
* Introduce 'nodomains' boot option, which clears pci_domains_supported
on platforms that enable it by default (x86, x86-64, and others when
they are converted to use this).
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For cases in which CONFIG_PCIEAER=y (such as distro kernels), allow users
to disable PCIE Advanced Error Reporting by using "pci=noaer" on the
kernel command line.
This can be used to work around hardware or (kernel) software problems.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replacing n & (n - 1) for power of 2 check by is_power_of_2(n)
Signed-off-by: vignesh babu <vignesh.babu@wipro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix undocumented function parameters in PCI and drivers/base.
Warning(linux-2.6.23-rc1//drivers/pci/pci.c:1526): No description found for parameter 'rq'
Warning(linux-2.6.23-rc1//drivers/base/firmware_class.c:245): No description found for parameter 'bin_attr'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: Kconfig: remove CONFIG_ACPI_SLEEP from source
ACPI: quiet ACPI Exceptions due to no _PTC or _TSS
ACPI: Remove references to ACPI_STATE_S2 from acpi_pm_enter
ACPI: Kconfig: always enable CONFIG_ACPI_SLEEP on X86
ACPI: Kconfig: fold /proc/acpi/sleep under CONFIG_ACPI_PROCFS
ACPI: Kconfig: CONFIG_ACPI_PROCFS now defaults to N
ACPI: autoload modules - Create __mod_acpi_device_table symbol for all ACPI drivers
ACPI: autoload modules - Create ACPI alias interface
ACPI: autoload modules - ACPICA modifications
ACPI: asus-laptop: Fix failure exits
ACPI: fix oops due to typo in new throttling code
ACPI: ignore _PSx method for hotplugable PCI devices
ACPI: Use ACPI methods to select PCI device suspend state
ACPI, PNP: hook ACPI D-state to PNP suspend/resume
ACPI: Add acpi_pm_device_sleep_state helper routine
ACPI: Implement the set_target() callback from pm_ops
Some odd ACPI implementations choke if certain controller is disabled
when ACPI suspend is invoked but we still need to make sure the PCI
device is enabled during resume. Simply using pci_enable_device()
unbalances device enable count. Export __pci_reenable_device().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
applied after Rafel's 'PM: Update global suspend and hibernation
operations framework' patch set
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Check for PCI_CAP_ID_PM before checking the device state. Apparently fixes
some log spam via the 3c59x driver.
Signed-off-by: Andrew Lunn <andrew.lunn@ascom.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As suggested by Andrew, add pci_try_set_mwi(), which does not require
return-value checking.
- add pci_try_set_mwi() without __must_check
- make it return 0 on success, errno if the "try" failed or error
- review callers
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch introduces an interface to read and write PCI-X / PCI-Express
maximum read byte count values from PCI config space. There is a second
function that returns the maximum _designed_ read byte count, which marks the
maximum value for a device, since some drivers try to set MMRBC to the
highest allowed value and rely on such a function.
Based on patch set by Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Peter Oruba <peter.oruba@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Functions marked __devinit will be removed after kernel init. But being
exported they are potentially called by a module much later.
So the safer choice seems to be to keep the function even in the non
CONFIG_HOTPLUG case.
This silence the follwoing section mismatch warnings:
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_add_device from __ksymtab_gpl between '__ksymtab_pci_bus_add_device' (at offset 0x20) and '__ksymtab_pci_walk_bus'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_create_bus from __ksymtab_gpl between '__ksymtab_pci_create_bus' (at offset 0x40) and '__ksymtab_pci_stop_bus_device'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_max_busnr from __ksymtab_gpl between '__ksymtab_pci_bus_max_busnr' (at offset 0xc0) and '__ksymtab_pci_assign_resource_fixed'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_claim_resource from __ksymtab_gpl between '__ksymtab_pci_claim_resource' (at offset 0xe0) and '__ksymtab_pcie_port_bus_type'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_add_devices from __ksymtab between '__ksymtab_pci_bus_add_devices' (at offset 0x70) and '__ksymtab_pci_bus_alloc_resource'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_scan_bus_parented from __ksymtab between '__ksymtab_pci_scan_bus_parented' (at offset 0x90) and '__ksymtab_pci_root_buses'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_assign_resources from __ksymtab between '__ksymtab_pci_bus_assign_resources' (at offset 0x4d0) and '__ksymtab_pci_bus_size_bridges'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_size_bridges from __ksymtab between '__ksymtab_pci_bus_size_bridges' (at offset 0x4e0) and '__ksymtab_pci_setup_cardbus'
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Warning(linux-2621-rc3g7/drivers/pci/pci.c:1283): No description found for parameter 'dev'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds a new API which can be used to issue various types
of PCI-E reset, including PCI-E warm reset and PCI-E hot reset.
This is needed for an ipr PCI-E adapter which does not properly
implement BIST. Running BIST on this adapter results in PCI-E
errors. The only reliable reset mechanism that exists on this
hardware is PCI Fundamental reset (warm reset). Since driving
this type of reset is architecture unique, this provides the
necessary hooks for architectures to add this support.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This defines a platform hook to enable/disable a device as a wakeup event
source. It's initially for use with ACPI, but more generally it could be used
whenever enable_irq_wake()/disable_irq_wake() don't suffice.
The hook is called -- if available -- inside pci_enable_wake(); and the
semantics of that call are enhanced so that support for PCI PME# is no longer
needed. It can now work for devices with "legacy PCI PM", when platform
support allows it. (That support would use some board-specific signal for for
the same purpose as PME#.)
[akpm@linux-foundation.org: Make it compile with CONFIG_PM=n]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because we do not reserve space for the pci-x and pci-e state in struct
pci dev we need to dynamically allocate it. However because we need
to support restore being called multiple times after a single save
it is never safe to free the buffers we have allocated to hold the
state.
So this patch modifies the save routines to first check to see
if we have already allocated a state buffer before allocating
a new one. Then the restore routines are modified to not free
the state after restoring it. Simple and it fixes some subtle
error path handling bugs, that are hard to test for.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are two ways pci_save_state and pci_restore_state are used. As
helper functions during suspend/resume, and as helper functions around
a hardware reset event. When used as helper functions around a hardware
reset event there is no reason to believe the calls will be paired, nor
is there a good reason to believe that if we restore the msi state from
before the reset that it will match the current msi state. Since arch
code may change the msi message without going through the driver, drivers
currently do not have enough information to even know when to call
pci_save_state to ensure they will have msi state in sync with the other
kernel irq reception data structures.
It turns out the solution is straight forward, cache the state in the
existing msi data structures (not the magic pci saved things) and
have the msi code update the cached state each time we write to the hardware.
This means we never need to read the hardware to figure out what the hardware
state should be.
By modifying the caching in this manner we get to remove our save_state
routines and only need to provide restore_state routines.
The only fields that were at all tricky to regenerate were the msi and msi-x
control registers and the way we regenerate them currently is a bit dependent
upon assumptions on how we use the allow msi registers to be configured and used
making the code a little bit brittle. If we ever change what cases we allow
or how we configure the msi bits we can address the fragility then.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sanity check in pcim_pin_device() was too restrictive in that it didn't
allow multiple calls to the function, which is against the devres
philosohpy of fire-and-forget. Track pinned status separately and allow
pinning multiple times.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
