flush_scheduled_work() is on its way out. This patch contains simple
conversions to replace flush_scheduled_work() usage with direct
cancels and flushes.
Directly cancel the used works on driver detach and flush them in
other cases.
The conversions are mostly straight forward and the only dangers are,
* Forgetting to cancel/flush one or more used works.
* Cancelling when a work should be flushed (ie. the work must be
executed once scheduled whether the driver is detaching or not).
I've gone over the changes multiple times but it would be much
appreciated if you can review with the above points in mind.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Divy Le Ray <divy@chelsio.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: Vasanthy Kolluri <vkolluri@cisco.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Andrew Gallatin <gallatin@myri.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: netdev@vger.kernel.org
fix a race at the end of NAPI complete processing, it had
better do __napi_complete() first before re-enable interrupt.
Signed-off-by:Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix rtl_chip_info buffer overrun when we can't identify the chip.
(i = ARRAY_SIZE (rtl_chip_info) in this case)
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ioread32() returns a 32-bit integer on all platforms.
There is no need to cast its return value.
Signed-off-by: Junchang Wang <junchangwang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Use netif_<level>
Convert formats like %8.8 to %08
Remove periods from formats
Coalesce long formats
Use print_hex_dump
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section
in every case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The id_table field of the struct pci_driver is constant in <linux/pci.h>
so it is worth to make pci_device_id also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: David S. Miller <davem@davemloft.net>
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a couple of cases collapse some extra code like:
int retval = NETDEV_TX_OK;
...
return retval;
into
return NETDEV_TX_OK;
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev() used to install a default implementation of this
operation, but it must now be explicitly installed in struct
net_device_ops.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.
Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also convert DPRINTK to pr_debug and dev_printk to dev_<foo>.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While ifconfig eth0 up kernel calls open() of 8139 driver(8139too.c).
In rtl8139_hw_start() of rtl8139_open(), 8139 driver enable RX before
setting up the DMA buffer address. In this interval where RX was
enabled and DMA buffer address is not yet set up, any incoming
broadcast packet would be send to a strange physical address:
0x003e8800 which is the default value of DMA buffer address.
Unfortunately, this address is used by Linux kernel. So kernel panics.
This patch fix it by setting up DMA buffer address before RX enabled
and everything is fine even under broadcast packets attack.
Signed-off-by: Jonathan Lin <jon.lin@vatics.com>
Signed-off-by: Amos Kong <jianjun@zeuux.org>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
unify the struct's name of "struct rtl8139_private *np" to "struct rtl8139_private *tp"
most of them like this:
struct rtl8139_private *tp = netdev_priv(dev);
Signed-off-by: Amos Kong <jianjun@zeuux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar patch as for 8139cp posted yesterday, so the same comment:
So far there was not a chance to set a mac address on running 8139too device.
This is for example needed when you want to use this NIC as a bonding slave in
bonding device in mode balance-alb. This simple patch allows it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers lost the ability to set ethernet address accidently
during the net_device_ops conversion.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using call by reference use the PTR_ERR macros to handle
return value with error case. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to new network device ops interface.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8139 drivers are a source of error messages that confuse users.
Since this device can not be disambiguated by normal PCI device
id's two drivers match the same info. But the module utilities
seem to correctly handle this overlap, they try one driver, then
if that doesn't load try the other. Therefore there is no need for
a message to be logged with error level severity, just using info
level instead. Can't be completely silent because user might have
configure one driver and forgot the other one.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The write barrier should be used before starting a DMA transfer. This fixes
a problem, where almost all packets received on another machine had garbled
content. Tested with an RTL8100C on a MIPS machine.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I would like to submit a correction to the driver
drivers/net/8139too.c,
which in no way changes the compiled driver, but does change
the value of a previously incorrect value for the configuration
register address of Flash PROM on the network processor rtl8139C.
This corrected value is in accordance with the datasheet
for rtl8139C, and in addition this new value is indeed used
in other functional drivers that use this adapter for
programming a Flash memory chip in situ. But as said,
the two new constants are never referenced in the driver
maintained by you: they are only informational and correct!
Mats Erik Andersson, meand@users.sourceforge.net
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch uses netdev_alloc_skb. This sets skb->dev and allows
arch specific allocation. Also cleanup the alignment code.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The OQO model 2 has an RTL8139 from Atheros that doesn't like MMIO.
It fails on modprobe, with a 'PCI Bus error' message.
Force it to always use polled IO.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is needed to support devices that only work with PIO without
penalising devices that work fine with MMIO in distro kernels.
It also allows us to eventually use PIO as a fallback when setting
up MMIO fails.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
synchronize_irq() is superfluous when free_irq() call immediately follows it,
because free_irq() also does a synchronize_irq() call of its own.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Clean up the following errors and warnings reported by checkpatch.pl:
+ ERROR: Macros with complex values should be enclosed in parenthesis
+ WARNING: __func__ should be used instead of gcc specific __FUNCTION__
+ WARNING: plain inline is preferred over __inline__
+ WARNING: Use #include <linux/io.h> instead of <asm/io.h>
+ WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
The changes were verified with by comparing the "objdump -d 8139too.ko"
output which is exactly the same for the old and new version in case of
config CONFIG_8139TOO=m, CONFIG_8139TOO_PIO=n, CONFIG_8139TOO_TUNE_TWISTER=n,
CONFIG_8139TOO_8129=n, CONFIG_8139_OLD_RX_RESET=n.
Software versions used: gcc 4.2.3, objdump 2.18.0.20080103, on elf32-i386.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use net_device_stats from net_device structure instead of local.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Updates the 8139too driver to work with recently added
(a724605cb7) declared coherent memory
patch for the Dreamcast.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
