* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: rs600: use correct mask for SW interrupt
gpu/drm/radeon/radeon_irq.c: move a dereference below a NULL test
drm/radeon/radeon_device.c: move a dereference below a NULL test
drm/radeon/radeon_fence.c: move a dereference below the NULL test
drm/radeon/radeon_connectors.c: add a NULL test before dereference
drm/radeon/kms: fix memory leak
drm/kms: Fix &&/|| confusion in drm_fb_helper_connector_parse_command_line()
drm/edid: Fix CVT width/height decode
drm/edid: Skip empty CVT codepoints
drm: remove address mask param for drm_pci_alloc()
drm/radeon/kms: add missing breaks in i2c and ss lookups
drm/radeon/kms: add primary dac adj values table
drm/radeon/kms: fallback to default connector table
* korg/drm-radeon-next:
drm/radeon/kms: rs600: use correct mask for SW interrupt
gpu/drm/radeon/radeon_irq.c: move a dereference below a NULL test
drm/radeon/radeon_device.c: move a dereference below a NULL test
drm/radeon/radeon_fence.c: move a dereference below the NULL test
drm/radeon/radeon_connectors.c: add a NULL test before dereference
drm/radeon/kms: fix memory leak
drm/radeon/kms: add missing breaks in i2c and ss lookups
drm/radeon/kms: add primary dac adj values table
drm/radeon/kms: fallback to default connector table
The mask happens to be the same, but the IH is reading the status, not the
not the control register.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If a NULL value is possible, the dereference should only occur after the
NULL test.
Coverity CID: 13338
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If a NULL value is possible, the dereference should only occur after the
NULL test.
Coverity CID: 13335
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If a NULL value is possible, the dereference should only occur after the
NULL test.
Coverity CID: 13334
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The encoder variable can be NULL in this function so I believe it should
be checked before dereference.
Coverity CID: 13253
[airlied: extremely unlikely to happen]
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Stanse found a memory leak in radeon_master_create. master_priv is not
freed/assigned on all paths. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_pci_alloc() has input of address mask for setting pci dma
mask on the device, which should be properly setup by drm driver.
And leave it as a param for drm_pci_alloc() would cause confusion
or mistake would corrupt the correct dma mask setting, as seen on
intel hw which set wrong dma mask for hw status page. So remove
it from drm_pci_alloc() function.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (23 commits)
drm/i915: remove full registers dump debug
drm/i915: Add DP dpll limit on ironlake and use existing DPLL search function
drm/i915: Select the correct BPC for LVDS on Ironlake
drm/i915: Make the BPC in FDI rx/transcoder be consistent with that in pipeconf on Ironlake
drm/i915: Enable/disable the dithering for LVDS based on VBT setting
drm/i915: Permit pinning whilst the device is 'suspended'
drm/i915: Hold struct mutex whilst pinning power context bo.
drm/i915: fix unused var
drm/i915: Storage class should be before const qualifier
drm/i915: remove render reclock support
drm/i915: Fix RC6 suspend/resume
drm/i915: execbuf2 support
drm/i915: Reload hangcheck timer too for Ironlake
drm/i915: only enable hotplug for detected outputs
drm/i915: Track whether cursor needs physical address in intel_device_info
drm/i915: Implement IS_* macros using static tables
drm/i915: Move PCI IDs into i915 driver
drm/i915: Update LVDS connector status when receiving ACPI LID event
drm/i915: Add MALATA PC-81005 to ACPI LID quirk list
drm/i915: implement new pm ops for i915
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] lpfc 8.3.7: Update Driver version to 8.3.7
[SCSI] lpfc 8.3.7: Fix discovery failures.
[SCSI] lpfc 8.3.7: Fix SCSI protocol related errors.
[SCSI] lpfc 8.3.7: Fix hardware/SLI relates issues
[SCSI] lpfc 8.3.7: Fix NPIV operation errors
[SCSI] lpfc 8.3.7: Fix FC protocol errors
[SCSI] stex: fix scan of nonexistent lun
[SCSI] pmcraid: fix to avoid twice scsi_dma_unmap for a command
[SCSI] qla2xxx: Update version number to 8.03.01-k9.
[SCSI] qla2xxx: Added to EEH support.
[SCSI] qla2xxx: Extend base EEH support in qla2xxx.
[SCSI] qla2xxx: Fix for a multiqueue bug in CPU affinity mode
[SCSI] qla2xxx: Get the link data rate explicitly during device resync.
[SCSI] cxgb3i: Fix a login over vlan issue
This one reverts 9e3a6d155e.
As reported by http://bugzilla.kernel.org/show_bug.cgi?id=14485,
this dump will cause hang problem on some machine. If something
really needs this kind of full registers dump, that could be done
within intel-gpu-tools.
Cc: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For some clocks, the old Ironlake DPLL calculator wold give m/n/p
combinations that didn't match the spreadsheet of what HW validation
tests. Instead, use the G4X DPLL calculator, which does a better job
at it.
So we use the intel_g4x_find_best_pll to calculate the DPLL for CRT/HDMI/LVDS
on ironlake. At the same time to consider the dpll setting for display port, we
add the display port DPLL limit on ironlake, which will directly use the
function of intel_find_pll_ironlake_dp to get the corresponding dpll setting.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Select the correct BPC for LVDS on Ironlake. If it is 18-bit LVDS panel,
the BPC will be 6. When it is 24-bit LVDS panel, the BPC will 8.
At the same time the BPC will be 8 when the output device is CRT/HDMI/DP.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Make the BPC in FDI rx/transcoder be consistent with that in pipeconf on Ironlake.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Enable/disable the dithering for LVDS based on VBT setting. On the 965/g4x
platform the dithering flag is defined in LVDS register. And on the ironlake
the dithering flag is defined in pipeconf register.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
As pinning (allocating and binding GTT memory) does not actually invoke
GPU commands, it is safe, and indeed is attempted, during resumption
from suspension:
[drm:intel_init_clock_gating] *ERROR* failed to pin power context: -16
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
Hugh found an error path where we were attempting to unref a bo without
holding the struct mutex:
[drm:intel_init_clock_gating] *ERROR* failed to pin power context: -16
------------[ cut here ]------------
WARNING: at drivers/gpu/drm/drm_gem.c:438 drm_gem_object_free+0x20/0x5e()
Hardware name: ESPRIMO Mobile V5505
Modules linked in: snd_pcm_oss snd_mixer_oss snd_seq snd_seq_device
Pid: 3793, comm: s2ram Not tainted 2.6.33-rc2 #4
Call Trace:
[<7815298e>] warn_slowpath_common+0x59/0x6b
[<781529b3>] warn_slowpath_null+0x13/0x18
[<78317c1a>] ? drm_gem_object_free+0x20/0x5e
[<78317c1a>] drm_gem_object_free+0x20/0x5e
[<78317bfa>] ? drm_gem_object_free+0x0/0x5e
[<7829df11>] kref_put+0x38/0x45
[<7833a5f0>] intel_init_clock_gating+0x232/0x271
[<78317bfa>] ? drm_gem_object_free+0x0/0x5e
[<7832c307>] i915_restore_state+0x21a/0x2b3
[<7832379d>] i915_resume+0x3c/0xbb
[<78174fe5>] ? trace_hardirqs_on_caller+0xfc/0x123
[<7831c756>] ? drm_class_resume+0x0/0x3e
[<7831c78d>] drm_class_resume+0x37/0x3e
[<78351e0a>] legacy_resume+0x1e/0x51
[<78351ece>] device_resume+0x91/0xab
[<7831c756>] ? drm_class_resume+0x0/0x3e
[<78352226>] dpm_resume+0x58/0x10f
[<783522fb>] dpm_resume_end+0x1e/0x2c
[<78180f80>] suspend_devices_and_enter+0x61/0x84
[<78180ff8>] enter_state+0x55/0x83
[<7818091c>] state_store+0x94/0xaa
[<7829d09e>] kobj_attr_store+0x1e/0x23
[<782098e0>] sysfs_write_file+0x66/0x99
[<781cd2f0>] vfs_write+0x8a/0x108
[<781cd408>] sys_write+0x3c/0x63
[<78125c10>] sysenter_do_call+0x12/0x36
---[ end trace a343537f29950fda ]---
It is in fact slightly more insiduous that first appears since we are
attempting to not just free the object without the lock, but are trying
to do the whole bo manipulation without holding the lock.
Reported-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
drivers/gpu/drm/i915/i915_dma.c: In function 'i915_driver_load':
drivers/gpu/drm/i915/i915_dma.c:1114: warning: 'll_base' may be used uninitialized in this function
Partly this is because gcc isn't smart enough. But `ll_base' does get used
uninitialised in the DRM_DEBUG() call.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
This code generally fails to adjust the render clock, and when it does,
it conflicts with some other register settings and can cause problems.
So remove this code altogether. I'm reworking it now to do the right
thing, but the only bit it will share is the VBT check for whether
reclocking is supported, so I'm leaving that bit.
Reverts most of 652c393a33 ("add dynamic
clock frequency control"), though for many the regressions showed up
in the later 181a5336d6 ("Fix render
reclock availability detection").
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
We restored RC6 twice on resume, even with modesetting off. Instead,
only restore it once and skip RC6 initialization entirely in non-KMS mode.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch adds a new execbuf ioctl, execbuf2, for use by clients that
want to control fence register allocation more finely. The buffer
passed in to the new ioctl includes a new relocation type to indicate
whether a given object needs a fence register assigned for the command
buffer in question.
Compatibility with the existing execbuf ioctl is implemented in terms
of the new code, preserving the assumption that fence registers are
required for pre-965 rendering commands.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: Remove pre-emptive clear_fence_reg()]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
[anholt: Removed dmesg spam]
Signed-off-by: Eric Anholt <eric@anholt.net>
* master.kernel.org:/home/rmk/linux-2.6-arm: (22 commits)
ARM: 5865/1: nuc900 ethernet driver needs mii
ARM: 5864/1: Implement arch_reset() in NUC900
ARM: 5863/1: fix bugs of clock source of NUC900
ARM: 5858/1: Remove unused vma_vm_flags macro from v7wbi_flush_user_tlb_range
imx/mx3: depend on USB_ULPI for otg_ulpi_create
ARM: MX3: make CPU revision number detection work on all boards
mx25: pdk: add platform code for FEC support
mx25: add support for FEC on i.MX25
mx25: s/NO_PAD_CTL/NO_PAD_CTRL/
mx31moboard: fix usbh device names
mx3: add support for the mt9v022 camera sensor to pcm037 platform
mx27: mxt_td60: Remove not used UART pins
[ARM] pxa/poodle: fix incorrect 'gpio_card_detect' of MMC
[ARM] pxa/zylonite: simplify reduntant gpio settings on mmc slot
[ARM] pxa/ttc_dkb: remove duplicate macro definition
[ARM] pxa/zeus: provide power-source information when APM is enabled
[ARM] pxa/zeus: relax memory timings on Zeus ethernet ports
[ARM] pxa/zeus: make internal zeus_get_pcb_info static
[ARM] pxa/littleton: select CPU_PXA300 and CPU_PXA310
[ARM] pxa/littleton: add UART3 GPIO config
...
Look up primary dac adj values from the table if
there is no bios or bios dac table to reference.
The lookup table may need to be adjusted for certain
families.
Should fix kernel bug 14945.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
if necessary for combios
Some early combios radeon cards don't have a connector
table or dac table in the bios, if they do not, fallback
to the default tables.
Should fix kernel bug 14963.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
nuc900 ethernet driver uses mii_xx_xx serials api, so mii module should be selected.
Signed-off-by: lijie <eltshanli@gmail.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In bbc_envctrl_init() we have to unlink the fan and temp instances
from the lists because our caller is going to free up the 'bp' object
if we return an error.
We can't rely upon bbc_envctrl_cleanup() to do this work for us in
this case.
Reported-by: Patrick Finnegan <pat@computer-refuge.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We kill the guest, but then we blatt random stuff.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] Update default configuration.
[S390] Have param.h simply include <asm-generic/param.h>.
[S390] qdio: convert global statistics to per-device stats
We wrap the smm calls and other bits with the BKL push down as a
precaution but they can probably go
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nobody seems to want to own I2O patches so sending this one directly.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The BKL is in this function because of the BKL pushdown (see commit
f8f2c79d59)
It is not needed here because the mutex_lock sonypi_device.lock provides
the necessary locking.
sonypi_misc_ioctl can be converted to unlocked ioctls since it relies on
its own locking (the mutex sonypi_device.lock) and not the bkl
Document that llseek is not needed by explictly setting it to no_llseek
LKML-Reference: <alpine.LFD.2.00.0910192019420.3563@localhost.localdomain>
Signed-off-by: John Kacur <jkacur@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix discovery failures:
- Move all accesses to the fc_flag field inside the host lock.
- Restore link state after going through linkdown processing for FCF DEAD event.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix SCSI protocol related errors:
- Avoid I/O failures during EEH and HBA/CNA reset by correcting when
we block the targets on the adapter.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix hardware/SLI relates issues:
- Fix CNA uses more than one EQ when in INTx interrupt mode.
- Fix driver tries to process failed read FCF record mailbox request.
- Fix allocating single receive buffer breaks FCoE receive queue.
- Support new read FCF record mailbox error case.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix NPIV operation errors:
- Fix vport not logging out of fabric when being deleted
- Fix vport fails to discover targets after devloss timeout.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix FC protocol errors:
- Fix multi-frame unsolicited sequences not queued properly
- Fix frames for unsolicited sequences not being associated with sequence.
- Fix unsolicited frame buffer sizes are not set properly
- Fix Sequence count for unsolicited frame headers not byte swapped.
- Fix Multi-frame sequence response frames go to wrong DID.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
During a manual scan, a user can send command to a nonexistent
lun, precisely at the point of max_lun. Normally it's possible
(but not required) that the firmware has the knowledge that it
is an invalid lun. In the particular case when max_lun is 256,
however, the nonexistent lun 256 will be confused with lun 0,
because the lun member in a request message is only u8, and 256
will become 0. So we need to fix the problem, at least, at the
driver level.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Revamp the qdio performance statistics and move them from procfs to
debugfs using the seq_file interface. Since the statistics are not
intended for the general user the removal of /proc/qdio_perf should
not surprise anyone.
The per device statistics are disabled by default, writing 1 to
/<debugfs mountpoint>/qdio/<device bus ID>/statistics enables the
statistics for the given device.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Commit 239007b844 ("genirq: Convert irq_desc.lock to raw_spinlock")
seems to have missed this driver, leaving it to use the normal spin-lock
functions for the irq descriptor lock, which is now a raw lock.
Reported-and-compile-tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduced by commit 5b889bf23 ("PCI: Fix build if quirks are not
enabled"), which made the pci_dev_reset_methods[] array static and
'const', but didn't then change the code to match, and use a const
pointer when moving it to quirks.c.
Trivially fixed by just adding the required 'const' to the iterator
variable.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
