user_util.h isn't needed any more, so delete it and remove all includes of it.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a number of problems associated with network interface hotplug.
The userspace initialization function can fail in some cases, but the
failure was never passed back to eth_configure, which proceeded with the
configuration. This results in a zombie device that is present, but can't
work. This is fixed by allowing the initialization routines to return an
error, which is checked, and the configuration aborted on failure.
eth_configure failed to check for many failures. Even when it did check,
it didn't undo whatever initializations has already happened, so a present,
but partially initialized and non-working device could result. It now
checks everything that can fail, and bails out, undoing whatever had been
done.
The return value of eth_configure was always ignored, so it is now just
void.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bunch of formatting violations in the drivers:
return(n) -> return n
whitespace fixes
emacs formatting comment removal
breaking if(foo) return(n) into two lines
There are also a couple of errno use bugs:
using errno in a printk when the failure put errno into a local variable
saving errno after a printk, which can change it
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Memory allocated by mcast_user_init must be freed in the matching mcast_remove.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
user.h is too generic a header name. I've split out allocation routines from
it.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make lots of structures const in order to make it obvious that they need no
locking.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
printk clears the host errno (I verified this in debugging and it's reasonable
enough, given that it ends via a write call on some fd, especially since
printk() goes on /dev/tty0 which is often the host stdout). So save errno
earlier. There's no reason to change the printk calls to use -err rather than
errno - the assignment can't clear errno.
And in the first failure path, we used to return 0 too (and this time more
clearly), which is totally wrong. 0 is a success fd, which is then registered
and gives a "registering fd twice" warning.
Finally, fix up some whitespace.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The poster child for this patch is the third tuntap_user hunk. When an ioctl
fails, it properly closes the opened file descriptor and returns. However,
the close resets errno to 0, and the 'return errno' that follows returns 0
rather than the value that ioctl set. This caused the caller to believe that
the device open succeeded and had opened file descriptor 0, which caused no
end of interesting behavior.
The rest of this patch is a pass through the UML sources looking for places
where errno could be reset before being passed back out. A common culprit is
printk, which could call write, being called before errno is returned.
In some cases, where the code ends up being much smaller, I just deleted the
printk.
There was another case where a caller of run_helper looked at errno after a
failure, rather than the return value of run_helper, which was the errno value
that it wanted.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
linux/inet.h isn't needed, and on my system, is empty.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Byte-swapping of the port and IP address passed in to the multicast driver by
the user used to happen in different places, which was a bug in itself. The
port also was swapped before being printk-ed, which led to a misleading
message. This patch moves the port swapping to the same place as the IP
address swapping. It also cleans up the error paths of mcast_open.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
