Blindly setting 1.2V in the initial structure may not even match the
default voltages stored in the voltage table which are supported for
the domain. For example, OMAP3430 core domain does not use 1.2V and
ends up generating a warning on the first transition.
Further, since omap2_set_init_voltage is called as part of the pm
framework's initialization sequence to configure the voltage required
for the current OPP, the call does(and has to) setup the system
voltage(curr_volt as a result) using the right mechanisms appropriate
for the system at that point of time. This also overrides
initialization we are currently doing in voltage.c making it
redundant. So, remove the wrong and redundant initialization.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 has two different Devices IVA and DSP. DSP is bound
with IVA for DVFS. The registration of IVA dev in API
'omap2_init_processor_devices' was missing. Init dev for
'iva_dev' is added.
This also fixes the following error seen during boot as
omap2_set_init_voltage can now find the iva device
omap2_set_init_voltage: Invalid parameters!
omap2_set_init_voltage: Unable to put vdd_iva to its init voltage
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
So that omap_vram_set_sdram_vram() is called before
omap_vram_reserve_sdram_memblock().
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If an error occurs in the L3 on any other initiator than MPU,
the interrupt goes unhandled given that the 'base' register
was calculated with the initialized err_source value (which
coincidentally points to MPU) and not with the actual source
of the error.
Removed parenthesis that are not needed for the touched lines.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fixes broken build when using binutils 2.21.
Signed-off-by: Oskar Andero <oskar.andero@sonyericsson.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: Fix warning 's3c_pm_show_resume_irqs' defined but not used
ARM: SAMSUNG: Fix build failure in PM CRC check code
ARM: S5P: Remove unused s3c_pm_check_resume_pin
There are optional bits that may complement a personality ID. It is
therefore wrong to simply test against the absolute current->personality
value to determine the effective personality. The PER_LINUX_32BIT is
itself just PER_LINUX with one of those optional bits set.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Our SET_PERSONALITY() implementation was overwriting all existing
personality flags, including ADDR_NO_RANDOMIZE, making them unavailable
to processes being exec'd after a call to personality() in user space.
This prevents the gdb test suite from running successfully.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This config option isn't actually used anywhere and can be safely
removed. The last user was traps.c before commit 082f47a ([ARM]
always allow dump_stack() to produce a backtrace, 2007-07-05).
Reviewed-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
s3c_pm_show_resume_irqs() is used by some s3c_pm_arch_show_resume_irqs()
implementations, which get included through mach/pm-core.h. Add __maybe_unused
to silence warnings when it isn't used (e.g. on S3C64XX platforms).
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes build error that occurs on enabling the Samsung
specific PM CRC check code. Missed removing this reference of
s3c_sleep_save_phys during move to generic cpu suspend/resume
support.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The s3c_pm_check_resume_pin() is not being used and can be safely
removed to fix the build warning.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This fixes the failure to register the IRQ_RTCAlrm alarm as a wakeup
event. It is misinterpreted as a gpio irq not a PWER bitmask. Fixed
this by converting the incorrect IRQ_TO_IRQ() to a correct version of
irq_to_gpio().
Reported-by: Nick Bane <nickbane1@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Avoid to mismatch between NR_BUILTIN_GPIO and gpio interrupt number.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Avoid to mismatch between NR_BUILTIN_GPIO and GPIO interrupt number
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The patch below removes an unused config variable found by using a kernel
cleanup script.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
VFP registers d16-d31 are callee saved registers and must be preserved
during function calls, including fork(). The VFP configuration should
also be preserved. The patch copies the full VFP state to the child
process.
Reported-by: Paul Wright <paul.wright@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds THREAD_NOTIFY_COPY for calling registered handlers
during the copy_thread() function call. It also changes the VFP handler
to use a switch statement rather than if..else and ignore this event.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The HIGHPTE config option depends on !OUTER_CACHE. However, there is no
set_pte_ext() function that does outer cache maintenance by physical
address, hence no need for such restriction.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit a737823d ("ARM: perf: ensure overflows aren't missed due to IRQ
latency") changed the way that event deltas are calculated on overflow
so that we don't miss events when the new count value overtakes the
previous one.
Unfortunately, we forget to count the event that passes through zero so
we end up being off by 1. This patch adds on the correction.
Reported-by: Chris Moore <moore@free.fr>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DBGVCR, used for configuring vector catch debug events, is UNKNOWN
out of reset on ARMv7. When enabling monitor mode, this must be zeroed
to avoid UNPREDICTABLE behaviour.
This patch adds the zeroing code to the debug reset path.
Cc: stable <stable@kernel.org>
Reported-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
ARM: arch-shmobile: only run FSI init on respective boards
ARM: arch-shmobile: only run HDMI init on respective boards
ARM: mach-shmobile: Correctly check for CONFIG_MACH_MACKEREL
If several boards are enabled in the kernel configuration,
fsi_init_pm_clock() functions from board-ap4evb.c
will run on any of them. Prevent this by calling these functions from the
.init_machine() callback instead of using device_initcall().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If several boards are enabled in the kernel configuration,
hdmi_init_pm_clock() functions from board-ap4evb.c and board-mackerel.c
will run on any of them. Prevent this by calling these functions from the
.init_machine() callback instead of using device_initcall().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
I made a bit of a thinko when adding Mackerel to the boards
that support zboot using MMCIF.
Reported-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Offering CONFIG_PM_SLEEP for CPUs which do not support suspend leads to
build errors, so only set CONFIG_ARCH_SUSPEND_POSSIBLE if we have a CPU
selected which supports suspend.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CONFIG_PM is now set whenever we support either runtime PM in addition
to suspend and hibernate. This causes build errors when runtime PM is
enabled on a platform, but the CPU does not have the appropriate support
for suspend.
So, switch this code to use CONFIG_PM_SLEEP rather than CONFIG_PM to
allow runtime PM to be enabled without causing build errors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Checking 'rate < 0' doesn't work because 'rate' is unsigned.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Colin Cross <ccross@android.com>
Change af90f10d38 "ARM: 6759/1: smp: Select local timers vs broadcast
timer support runtime" missed a return statement, causing a compile
warning:
arch/arm/mach-msm/timer.c:272: warning: 'return' with no value, in
function returning non-void
Trivially return 0 for success when running on cpu 0 (to match the
comment and previous behavior).
Signed-off-by: David Brown <davidb@codeaurora.org>
The qsd8x50 board file contains a few references to machine_is_...
macros that are otherwise unused, and contain no machine definition.
The recent purge of unused machine definitions breaks the compilation
of this target.
Since the machine cannot ever be used, just remove the bogus checks.
Signed-off-by: David Brown <davidb@codeaurora.org>
Change b0f18edaf6
(arm: tegra: Remove unused bogus irq enable/disable magic)
introduces warnings:
arch/arm/mach-tegra/gpio.c: In function 'tegra_gpio_resume':
arch/arm/mach-tegra/gpio.c:260: warning: unused variable 'i'
arch/arm/mach-tegra/gpio.c: In function 'tegra_gpio_suspend':
arch/arm/mach-tegra/gpio.c:283: warning: unused variable 'i'
Fix them, and fix a coding style issue on the same lines.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Erik Gilling <konkers@konkers.net>
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
avr32: Fix missing irq namespace conversion
powerpc: qe_ic: Rename get_irq_desc_data and get_irq_desc_chip
genirq: Remove the now obsolete config options and select statements
arm: versatile : Fix typo introduced in irq namespace cleanup
sound: Fixup the last user of the old irq functions
genirq: Remove obsolete comment
genirq: Remove now obsolete set_irq_wake()
sh: Fix irq cleanup fallout
x86: apb_timer: Fixup genirq fallout
genirq: Fix misnamed label in handle_edge_eoi_irq
Fix up crazy conflict in arch/powerpc/include/asm/qe_ic.h:
- commit eead4d5c63 ("powerpc: qe_ic: Rename get_irq_desc_data and
get_irq_desc_chip") made the helper functions use
irq_desc_get_handler_data() instead of the legacy (and no longer
existing) get_irq_desc_data.
- commit d4db35e8dc ("powerpc/qe_ic: Fix another breakage from the
irq_data conversion") used irq_desc_get_chip_data() instead.
According to Thomas, the former is the correct direct conversion, but it
does look like both should work (arch/powerpc/sysdev/qe_lib/qe_ic.c
seems to initialize both to the same thing), and the chip data in some
ways is the more logical. Somebody should really decide on one of the
other.
This merge picks irq_desc_get_handler_data() as the straightforward pure
conversion to new names, as per Thomas.
Commit 6845664(arm: Cleanup the irq namespace) introduces a typo
causing a build failure for the versatile platform.
[ tglx: Sorry, my bad. Have no idea how I fatfingered that ]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
LKML-Reference: <20110330060229.27397.7628.stgit@ponder>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (26 commits)
mmc: SDHI should depend on SUPERH || ARCH_SHMOBILE
mmc: tmio_mmc: Move some defines into a shared header
mmc: tmio: support aggressive clock gating
mmc: tmio: fix power-mode interpretation
mmc: tmio: remove work-around for unmasked SDIO interrupts
sh: fix SDHI IO address-range
ARM: mach-shmobile: fix SDHI IO address-range
mmc: tmio: only access registers above 0xff, if available
mfd: remove now redundant sh_mobile_sdhi.h header
sh: convert boards to use linux/mmc/sh_mobile_sdhi.h
ARM: mach-shmobile: convert boards to use linux/mmc/sh_mobile_sdhi.h
mmc: tmio: convert the SDHI MMC driver from MFD to a platform driver
sh: ecovec: use the CONFIG_MMC_TMIO symbols instead of MFD
mmc: tmio: split core functionality, DMA and MFD glue
mmc: tmio: use PIO for short transfers
mmc: tmio-mmc: Improve DMA stability on sh-mobile
mmc: fix mmc_app_send_scr() for dma transfer
mmc: sdhci-esdhc: enable esdhc on imx53
mmc: sdhci-esdhc: use writel/readl as general APIs
mmc: sdhci: add the abort CMDTYPE bits definition
...
Reorder
irq_set_chip()
irq_set_chip_data()
irq_set_handler()
to
irq_set_chip()
irq_set_handler()
irq_set_chip_data()
so the next patch can combine irq_set_chip() and irq_set_handler() to
irq_set_chip_and_handler().
Automated conversion with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Avoid the whole lazy disable dance in the demux handler by providing a
irq_disable() callback.
Use the proper accessor functions and tidy up gpio_irq_handler()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make use of the new functionality which ensures that irq_set_type is
called with the chip masked. Unmask is only done when the interrupt is
not disabled.
Retrieve the trigger type from irq_data in unmask
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
