Impact: makes device isolation the default for AMD IOMMU
Some device drivers showed double-free bugs of DMA memory while testing
them with AMD IOMMU. If all devices share the same protection domain
this can lead to data corruption and data loss. Prevent this by putting
each device into its own protection domain per default.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This reverts commit e51af66308, which was
wrongly hoovered up and submitted about a month after a better fix had
already been merged.
The better fix is commit cbda1ba898
("PCI/iommu: blacklist DMAR on Intel G31/G33 chipsets"), where we do
this blacklisting based on the DMI identification for the offending
motherboard, since sometimes this chipset (or at least a chipset with
the same PCI ID) apparently _does_ actually have an IOMMU.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'kvm-updates/2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: Fix pit memory leak if unable to allocate irq source id
KVM: ia64: fix vmm_spin_{un}lock for !CONFIG_SMP
KVM: VMX: Set IGMT bit in EPT entry
KVM: Require the PCI subsystem
x86: KVM guest: fix section mismatch warning in kvmclock.c
KVM: ia64: Use guest signal mask when blocking
KVM: MMU: increase per-vcpu rmap cache alloc size
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (47 commits)
ACPI: pci_link: remove acpi_irq_balance_set() interface
fujitsu-laptop: Add DMI callback for Lifebook S6420
ACPI: EC: Don't do transaction from GPE handler in poll mode.
ACPI: EC: lower interrupt storm treshold
ACPICA: Use spinlock for acpi_{en|dis}able_gpe
ACPI: EC: restart failed command
ACPI: EC: wait for last write gpe
ACPI: EC: make kernel messages more useful when GPE storm is detected
ACPI: EC: revert msleep patch
thinkpad_acpi: fingers off backlight if video.ko is serving this functionality
sony-laptop: fingers off backlight if video.ko is serving this functionality
msi-laptop: fingers off backlight if video.ko is serving this functionality
fujitsu-laptop: fingers off backlight if video.ko is serving this functionality
eeepc-laptop: fingers off backlight if video.ko is serving this functionality
compal: fingers off backlight if video.ko is serving this functionality
asus-acpi: fingers off backlight if video.ko is serving this functionality
Acer-WMI: fingers off backlight if video.ko is serving this functionality
ACPI video: if no ACPI backlight support, use vendor drivers
ACPI: video: Ignore devices that aren't present in hardware
Delete an unwanted return statement at evgpe.c
...
This removes the acpi_irq_balance_set() interface from the PCI
interrupt link driver.
x86 used acpi_irq_balance_set() to tell the PCI interrupt link
driver to configure links to minimize IRQ sharing. But the link
driver can easily figure out whether to turn on IRQ balancing
based on the IRQ model (PIC/IOAPIC/etc), so we can get rid of
that external interface.
It's better for the driver to figure this out at init-time. If
we set it externally via the x86 code, the interface reduces
modularity, and we depend on the fact that acpi_process_madt()
happens before we process the kernel command line.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There is a potential issue that, when guest using pagetable without vmexit when
EPT enabled, guest would use PAT/PCD/PWT bits to index PAT msr for it's memory,
which would be inconsistent with host side and would cause host MCE due to
inconsistent cache attribute.
The patch set IGMT bit in EPT entry to ignore guest PAT and use WB as default
memory type to protect host (notice that all memory mapped by KVM should be WB).
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
WARNING: arch/x86/kernel/built-in.o(.text+0x1722c): Section mismatch
in reference from the function kvm_setup_secondary_clock() to the
function .devinit.text:setup_secondary_APIC_clock()
The function kvm_setup_secondary_clock() references
the function __devinit setup_secondary_APIC_clock().
This is often because kvm_setup_secondary_clock lacks a __devinit
annotation or the annotation of setup_secondary_APIC_clock is wrong.
Signed-off-by: Md.Rakib H. Mullick <rakib.mullick@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: handle HRTIMER_CB_IRQSAFE_UNLOCKED correctly from softirq context
nohz: disable tick_nohz_kick_tick() for now
irq: call __irq_enter() before calling the tick_idle_check
x86: HPET: enter hpet_interrupt_handler with interrupts disabled
x86: HPET: read from HPET_Tn_CMP() not HPET_T0_CMP
x86: HPET: convert WARN_ON to WARN_ON_ONCE
The page fault path can use two rmap_desc structures, if:
- walk_addr's dirty pte update allocates one rmap_desc.
- mmu_lock is dropped, sptes are zapped resulting in rmap_desc being
freed.
- fetch->mmu_set_spte allocates another rmap_desc.
Increase to 4 for safety.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
While investigating the failure of hibernation on 32-bit x86 with
CONFIG_NUMA set, as described in this message
http://marc.info/?l=linux-kernel&m=122634118116226&w=4
I asked some people for help and I was told that it wasn't really
worth the effort, because CONFIG_NUMA was generally broken on 32-bit
x86 systems and it shouldn't be used in such configs. For this
reason, make CONFIG_NUMA depend on BROKEN instead of EXPERIMENTAL on
x86-32.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Pavel Machek <pavel@suse.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some functions that may be called from this handler require that
interrupts are disabled. Also, combining IRQF_DISABLED and
IRQF_SHARED does not reliably disable interrupts in a handler, so
remove IRQF_SHARED from the irq flags (this irq is not shared anyway).
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Cc: mingo@elte.hu
Cc: venkatesh.pallipadi@intel.com
Cc: "Will Newton" <will.newton@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In hpet_next_event() we check that the value we just wrote to
HPET_Tn_CMP(timer) has reached the chip. Currently, we're checking that
the value we wrote to HPET_Tn_CMP(timer) is in HPET_T0_CMP, which, if
timer is anything other than timer 0, is likely to fail.
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Cc: mingo@elte.hu
Cc: venkatesh.pallipadi@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It is possible to flood the console with call traces if the WARN_ON
condition is true because of the frequency with which this function is
called.
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Cc: mingo@elte.hu
Cc: venkatesh.pallipadi@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: optimize sched_clock() a bit
sched: improve sched_clock() performance
sched_clock() uses cycles_2_ns() needlessly - which is an irq-disabling
variant of __cycles_2_ns().
Most of the time sched_clock() is called with irqs disabled already.
The few places that call it with irqs enabled need to be updated.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
in scheduler-intense workloads native_read_tsc() overhead accounts for
20% of the system overhead:
659567 system_call 41222.9375
686796 schedule 435.7843
718382 __switch_to 665.1685
823875 switch_mm 4526.7857
1883122 native_read_tsc 55385.9412
9761990 total 2.8468
this is large part due to the rdtsc_barrier() that is done before
and after reading the TSC.
But sched_clock() is not a precise clock in the GTOD sense, using such
barriers is completely pointless. So remove the barriers and only use
them in vget_cycles().
This improves lat_ctx performance by about 5%.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, xen: fix use of pgd_page now that it really does return a page
Fix the counter overflow check for CPUs with counter width > 32
I had a similar change in a different patch that I didn't submit
and I didn't notice the problem earlier because it was always
tested together.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Xen requires that all mappings of pagetable pages are read-only, so
that they can't be updated illegally. As a result, if a page is being
turned into a pagetable page, we need to make sure all its mappings
are RO.
If the page had been used for ioremap or vmalloc, it may still have
left over mappings as a result of not having been lazily unmapped.
This change makes sure we explicitly mop them all up before pinning
the page.
Unlike aliases created by kmap, the there can be vmalloc aliases even
for non-high pages, so we must do the flush unconditionally.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Linux Memory Management List <linux-mm@kvack.org>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
Revert "x86: default to reboot via ACPI"
x86: align DirectMap in /proc/meminfo
AMD IOMMU: fix lazy IO/TLB flushing in unmap path
x86: add smp_mb() before sending INVALIDATE_TLB_VECTOR
x86: remove VISWS and PARAVIRT around NR_IRQS puzzle
x86: mention ACPI in top-level Kconfig menu
x86: size NR_IRQS on 32-bit systems the same way as 64-bit
x86: don't allow nr_irqs > NR_IRQS
x86/docs: remove noirqbalance param docs
x86: don't use tsc_khz to calculate lpj if notsc is passed
x86, voyager: fix smp_intr_init() compile breakage
AMD IOMMU: fix detection of NP capable IOMMUs
Impact: fix 32-bit Xen guest boot crash
On 32-bit PAE, pud_page, for no good reason, didn't really return a
struct page *. Since Jan Beulich's fix "i386/PAE: fix pud_page()",
pud_page does return a struct page *.
Because PAE has 3 pagetable levels, the pud level is folded into the
pgd level, so pgd_page() is the same as pud_page(), and now returns
a struct page *. Update the xen/mmu.c code which uses pgd_page()
accordingly.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit c7ffa6c262.
the assumptio of this change was that this would not break
any existing machine. Andrey Borzenkov reported troubles with
the ACPI reboot method: the system would hang on reboot, necessiating
a power cycle. Probably more systems are affected as well.
Also, there are patches queued up for v2.6.29 to disable virtualization
on emergency_restart() - which was the original motivation of
this change.
Reported-by: Andrey Borzenkov <arvidjaar@mail.ru>
Bisected-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: right-align /proc/meminfo consistent with other fields
When the split-LRU patches added Inactive(anon) and Inactive(file) lines
to /proc/meminfo, all counts were moved two columns rightwards to fit in.
Now move x86's DirectMap lines two columns rightwards to line up.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Lazy flushing needs to take care of the unmap path too which is not yet
implemented and leads to stale IO/TLB entries. This is fixed by this
patch.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Impact: fix rare x2apic hang
On x86, x2apic mode accesses for sending IPI's don't have serializing
semantics. If the IPI receivner refers(in lock-free fashion) to some
memory setup by the sender, the need for smp_mb() before sending the
IPI becomes critical in x2apic mode.
Add the smp_mb() in native_flush_tlb_others() before sending the IPI.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix warning message when PARAVIRT is set in config
Remove stale #ifdef components from our IRQ sizing logic.
x86/Voyager is the only holdout.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: clarify menuconfig text
Mention ACPI in the top-level menu to give a clue as to where
it lives. This matches what ia64 does.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: make NR_IRQS big enough for system with lots of apic/pins
If lots of IO_APIC's are there (or can be there), size the same way
as 64-bit, depending on MAX_IO_APICS and NR_CPUS.
This fixes the boot problem reported by Ben Hutchings on a 32-bit
server with 5 IO-APICs and 240 IO-APIC pins.
Signed-off-by: Yinghai <yinghai@kernel.org>
Tested-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix boot hang on 32-bit systems with more than 224 IO-APIC pins
On some 32-bit systems with a lot of IO-APICs probe_nr_irqs() can
return a value larger than NR_IRQS. This will lead to probe_irq_on()
overrunning the irq_desc array.
I hit this when running net-next-2.6 (close to 2.6.28-rc3) on a
Supermicro dual Xeon system. NR_IRQS is 224 but probe_nr_irqs() detects
5 IOAPICs and returns 240. Here are the log messages:
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
Tue Nov 4 16:53:47 2008 IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x02] address[0xfec81000] gsi_base[24])
Tue Nov 4 16:53:47 2008 IOAPIC[1]: apic_id 2, version 32, address 0xfec81000, GSI 24-47
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x03] address[0xfec81400] gsi_base[48])
Tue Nov 4 16:53:47 2008 IOAPIC[2]: apic_id 3, version 32, address 0xfec81400, GSI 48-71
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x04] address[0xfec82000] gsi_base[72])
Tue Nov 4 16:53:47 2008 IOAPIC[3]: apic_id 4, version 32, address 0xfec82000, GSI 72-95
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x05] address[0xfec82400] gsi_base[96])
Tue Nov 4 16:53:47 2008 IOAPIC[4]: apic_id 5, version 32, address 0xfec82400, GSI 96-119
Tue Nov 4 16:53:47 2008 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
Tue Nov 4 16:53:47 2008 ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Tue Nov 4 16:53:47 2008 Enabling APIC mode: Flat. Using 5 I/O APICs
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: improve wakeup affinity on NUMA systems, tweak SMP systems
Given the fixes+tweaks to the wakeup-buddy code, re-tweak the domain
balancing defaults on NUMA and SMP systems.
Turn on SD_WAKE_AFFINE which was off on x86 NUMA - there's no reason
why we would not want to have wakeup affinity across nodes as well.
(we already do this in the standard NUMA template.)
lat_ctx on a NUMA box is particularly happy about this change:
before:
| phoenix:~/l> ./lat_ctx -s 0 2
| "size=0k ovr=2.60
| 2 5.70
after:
| phoenix:~/l> ./lat_ctx -s 0 2
| "size=0k ovr=2.65
| 2 2.07
a 2.75x speedup.
pipe-test is similarly happy about it too:
| phoenix:~/sched-tests> ./pipe-test
| 18.26 usecs/loop.
| 14.70 usecs/loop.
| 14.38 usecs/loop.
| 10.55 usecs/loop. # +WAKE_AFFINE on domain0+domain1
| 8.63 usecs/loop.
| 8.59 usecs/loop.
| 9.03 usecs/loop.
| 8.94 usecs/loop.
| 8.96 usecs/loop.
| 8.63 usecs/loop.
Also:
- disable SD_BALANCE_NEWIDLE on NUMA and SMP domains (keep it for siblings)
- enable SD_WAKE_BALANCE on SMP domains
Sysbench+postgresql improves all around the board, quite significantly:
.28-rc3-11474e2c .28-rc3-11474e2c-tune
-------------------------------------------------
1: 571 688 +17.08%
2: 1236 1206 -2.55%
4: 2381 2642 +9.89%
8: 4958 5164 +3.99%
16: 9580 9574 -0.07%
32: 7128 8118 +12.20%
64: 7342 8266 +11.18%
128: 7342 8064 +8.95%
256: 7519 7884 +4.62%
512: 7350 7731 +4.93%
-------------------------------------------------
SUM: 55412 59341 +6.62%
So it's a win both for the runup portion, the peak area and the tail.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix udelay when "notsc" boot parameter is passed
With notsc passed on commandline, tsc may not be used for
udelays, make sure that we do not use tsc_khz to calculate
the lpj value in such cases.
Reported-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'io-mappings-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
io mapping: clean up #ifdefs
io mapping: improve documentation
i915: use io-mapping interfaces instead of a variety of mapping kludges
resources: add io-mapping functions to dynamically map large device apertures
x86: add iomap_atomic*()/iounmap_atomic() on 32-bit using fixmaps
Impact: cleanup
clean up ifdefs: change #ifdef CONFIG_X86_32/64 to
CONFIG_HAVE_ATOMIC_IOMAP.
flip around the #ifdef sections to clean up the structure.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix x86/Voyager build
Looks like this became static on the rest of x86. Fix it up by adding
an external definition to mach-voyager/setup.c
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix AMDC1E and XTOPOLOGY conflict in cpufeature
x86: build fix
This makes the late e820 resources use 'insert_resource_expand_to_fit()'
instead of doing a 'reserve_region_with_split()', and also avoids
marking them as IORESOURCE_BUSY.
This results in us being perfectly happy to use pre-existing PCI
resources even if they were marked as being in a reserved region, while
still avoiding any _new_ allocations in the reserved regions. It also
makes for a simpler and more accurate resource tree.
Example resource allocation from Jonathan Corbet, who has firmware that
has an e820 reserved entry that covered a big range (e0000000-fed003ff),
and that had various PCI resources in it set up by firmware.
With old kernels, the reserved range would force us to re-allocate all
pre-existing PCI resources, and his reserved range would end up looking
like this:
e0000000-fed003ff : reserved
fec00000-fec00fff : IOAPIC 0
fed00000-fed003ff : HPET 0
where only the pre-allocated special regions (IOAPIC and HPET) were kept
around.
With 2.6.28-rc2, which uses 'reserve_region_with_split()', Jonathan's
resource tree looked like this:
e0000000-fe7fffff : reserved
fe800000-fe8fffff : PCI Bus 0000:01
fe800000-fe8fffff : reserved
fe900000-fe9d9aff : reserved
fe9d9b00-fe9d9bff : 0000:00:1f.3
fe9d9b00-fe9d9bff : reserved
fe9d9c00-fe9d9fff : 0000:00:1a.7
fe9d9c00-fe9d9fff : reserved
fe9da000-fe9dafff : 0000:00:03.3
fe9da000-fe9dafff : reserved
fe9db000-fe9dbfff : 0000:00:19.0
fe9db000-fe9dbfff : reserved
fe9dc000-fe9dffff : 0000:00:1b.0
fe9dc000-fe9dffff : reserved
fe9e0000-fe9fffff : 0000:00:19.0
fe9e0000-fe9fffff : reserved
fea00000-fea7ffff : 0000:00:02.0
fea00000-fea7ffff : reserved
fea80000-feafffff : 0000:00:02.1
fea80000-feafffff : reserved
feb00000-febfffff : 0000:00:02.0
feb00000-febfffff : reserved
fec00000-fed003ff : reserved
fec00000-fec00fff : IOAPIC 0
fed00000-fed003ff : HPET 0
and because the reserved entry had been split and moved into the
individual resources, and because it used the IORESOURCE_BUSY flag, the
drivers that actually wanted to _use_ those resources couldn't actually
attach to them:
e1000e 0000:00:19.0: BAR 0: can't reserve mem region [0xfe9e0000-0xfe9fffff]
HDA Intel 0000:00:1b.0: BAR 0: can't reserve mem region [0xfe9dc000-0xfe9dffff]
with this patch, the resource tree instead becomes
e0000000-fed003ff : reserved
fe800000-fe8fffff : PCI Bus 0000:01
fe9d9b00-fe9d9bff : 0000:00:1f.3
fe9d9c00-fe9d9fff : 0000:00:1a.7
fe9d9c00-fe9d9fff : ehci_hcd
fe9da000-fe9dafff : 0000:00:03.3
fe9db000-fe9dbfff : 0000:00:19.0
fe9db000-fe9dbfff : e1000e
fe9dc000-fe9dffff : 0000:00:1b.0
fe9dc000-fe9dffff : ICH HD audio
fe9e0000-fe9fffff : 0000:00:19.0
fe9e0000-fe9fffff : e1000e
fea00000-fea7ffff : 0000:00:02.0
fea80000-feafffff : 0000:00:02.1
feb00000-febfffff : 0000:00:02.0
fec00000-fec00fff : IOAPIC 0
fed00000-fed003ff : HPET 0
ie the one reserved region now ends up surrounding all the PCI resources
that were allocated inside of it by firmware, and because it is not
marked BUSY, drivers have no problem attaching to the pre-allocated
resources.
Reported-and-tested-by: Jonathan Corbet <corbet@lwn.net>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: introduce new APIs, separate kmap code from CONFIG_HIGHMEM
This takes the code used for CONFIG_HIGHMEM memory mappings except that
it's designed for dynamic IO resource mapping.
These fixmaps are available even with CONFIG_HIGHMEM turned off.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: build fix on certain UP configs
fix:
arch/x86/kernel/cpu/common.c: In function 'cpu_init':
arch/x86/kernel/cpu/common.c:1141: error: 'boot_cpu_id' undeclared (first use in this function)
arch/x86/kernel/cpu/common.c:1141: error: (Each undeclared identifier is reported only once
arch/x86/kernel/cpu/common.c:1141: error: for each function it appears in.)
Pull in asm/smp.h on UP, so that we get the definition of
boot_cpu_id.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: fix irq vectors.
lguest: fix early_ioremap.
lguest: fix example launcher compile after moved asm-x86 dir.
do_IRQ: cannot handle IRQ -1 vector 0x20 cpu 0
------------[ cut here ]------------
kernel BUG at arch/x86/kernel/irq_32.c:219!
We're not ISA: we have a 1:1 mapping from vectors to irqs.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
dmi_scan_machine breaks under lguest:
lguest: unhandled trap 14 at 0xc04edeae (0xffa00000)
This is because we use current_cr3 for the read_cr3() paravirt
function, and it isn't set until the first cr3 change. We got away
with it until this happened.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
fix:
arch/x86/kernel/cpu/common.c: In function 'early_identify_cpu':
arch/x86/kernel/cpu/common.c:553: error: 'struct cpuinfo_x86' has no member named 'cpu_index'
as cpu_index is only available on SMP.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
