In the course of the recent unification of the NMI watchdog an assignment
to timer_ack to switch off unnecesary POLL commands to the 8259A in the
case of a watchdog failure has been accidentally removed. The statement
used to be limited to the 32-bit variation as since the rewrite of the
timer code it has been relevant for the 82489DX only. This change brings
it back.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is no such entity as ISA IRQ2. The ACPI spec does not make it
explicitly clear, but does not preclude it either -- all it says is ISA
legacy interrupts are identity mapped by default (subject to overrides),
but it does not state whether IRQ2 exists or not. As a result if there is
no IRQ0 override, then IRQ2 is normally initialised as an ISA interrupt,
which implies an edge-triggered line, which is unmasked by default as this
is what we do for edge-triggered I/O APIC interrupts so as not to miss an
edge.
To the best of my knowledge it is useless, as IRQ2 has not been in use
since the PC/AT as back then it was taken by the 8259A cascade interrupt
to the slave, with the line position in the slot rerouted to newly-created
IRQ9. No device could thus make use of this line with the pair of 8259A
chips. Now in theory INTIN2 of the I/O APIC may be usable, but the
interrupt of the device wired to it would not be available in the PIC mode
at all, so I seriously doubt if anybody decided to reuse it for a regular
device.
However there are two common uses of INTIN2. One is for IRQ0, with an
ACPI interrupt override (or its equivalent in the MP table). But in this
case IRQ2 is gone entirely with INTIN0 left vacant. The other one is for
an 8959A ExtINTA cascade. In this case IRQ0 goes to INTIN0 and if ACPI is
used INTIN2 is assumed to be IRQ2 (there is no override and ACPI has no
way to report ExtINTA interrupts). This is where a problem happens.
The problem is INTIN2 is configured as a native APIC interrupt, with a
vector assigned and the mask cleared. And the line may indeed get active
and inject interrupts if the master 8959A has its timer interrupt enabled
(it might happen for other interrupts too, but they are normally masked in
the process of rerouting them to the I/O APIC). There are two cases where
it will happen:
* When the I/O APIC NMI watchdog is enabled. This is actually a misnomer
as the watchdog pulses are delivered through the 8259A to the LINT0
inputs of all the local APICs in the system. The implication is the
output of the master 8259A goes high and low repeatedly, signalling
interrupts to INTIN2 which is enabled too!
[The origin of the name is I think for a brief period during the
development we had a capability in our code to configure the watchdog to
use an I/O APIC input; that would be INTIN2 in this scenario.]
* When the native route of IRQ0 via INTIN0 fails for whatever reason -- as
it happens with the system considered here. In this scenario the timer
pulse is delivered through the 8259A to LINT0 input of the local APIC of
the bootstrap processor, quite similarly to how is done for the watchdog
described above. The result is, again, INTIN2 receives these pulses
too. Rafael's system used to escape this scenario, because an incorrect
IRQ0 override would occupy INTIN2 and prevent it from being unmasked.
My conclusion is IRQ2 should be excluded from configuration in all the
cases and the current exception for ACPI systems should be lifted. The
reason being the exception not only being useless, but harmful as well.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Unlike the 32-bit one, the 64-bit variation of the LVT0 setup code for
the "8259A Virtual Wire" through the local APIC timer configuration does
not fully configure the relevant irq_chip structure. Instead it relies on
the preceding I/O APIC code to have set it up, which does not happen if
the I/O APIC variants have not been tried.
The patch includes corresponding changes to the 32-bit variation too
which make them both the same, barring a small syntactic difference
involving sequence of functions in the source. That should work as an aid
with the upcoming merge.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
IRQ0 is edge-triggered, but the "8259A Virtual Wire" through the local
APIC configuration in the 32-bit version uses the "fasteoi" handler
suitable for level-triggered APIC interrupt. Rewrite code so that the
"edge" handler is used. The 64-bit version uses different code and is
unaffected.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The RING0_INT_FRAME macro defines a CFI_STARTPROC.
So we should really be using CFI_ENDPROC after it.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add pseudo-feature bits to describe whether the CPU supports sysenter
and/or syscall from ia32-compat userspace. This removes a hardcoded
test in vdso32-setup.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Yinghai Lu reported crashes on 64-bit x86:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
IP: [<ffffffff80253b17>] hrtick_start_fair+0x89/0x173
[...]
And with a long session of debugging and a lot of difficulty, tracked it down
to this commit:
--------------->
8fbbc4b45c is first bad commit
commit 8fbbc4b45c
Author: Alok Kataria <akataria@vmware.com>
Date: Tue Jul 1 11:43:34 2008 -0700
x86: merge tsc_init and clocksource code
<--------------
The problem is that the TSC unification missed these Makefile rules
in arch/x86/kernel/Makefile:
# Do not profile debug and lowlevel utilities
CFLAGS_REMOVE_tsc_64.o = -pg
CFLAGS_REMOVE_tsc_32.o = -pg
...
CFLAGS_tsc_64.o := $(nostackp)
...
which rules make sure that various instrumentation and debugging
facilities are disabled for code that might end up in a VDSO - such as
the TSC code.
Reported-and-bisected-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conflicts:
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when more than 4g memory is installed, don't map the big hole below 4g.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
also let mem= to print out modified e820 map too
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Integration generated a duplicate call to use_tsc_delay.
Particularly, the one that is done before we check for general
tsc usability seems wrong.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/kernel/visws_quirks.c: In function ‘visws_early_detect’:
arch/x86/kernel/visws_quirks.c:293: error: ‘no_broadcast’ undeclared (first use in this function)
arch/x86/kernel/visws_quirks.c:293: error: (Each undeclared identifier is reported only once
arch/x86/kernel/visws_quirks.c:293: error: for each function it appears in.)
make[1]: *** [arch/x86/kernel/visws_quirks.o] Error 1
make: *** [arch/x86/kernel/visws_quirks.o] Error 2
Signed-off-by: Ingo Molnar <mingo@elte.hu>
this is the big move: flip over VISWS to generic arch support.
From this commit on CONFIG_X86_VISWS is just another (default-disabled)
option that turns on certain quirks - no other complications.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
copy arch/x86/mach-visws/setup_visws.c, apic_visws.c and traps_visws.c
files to arch/x86/kernel/, in preparation of the switchover to a
non-subarch setup for VISWS.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
first step: make the VISWS subarch boot on a regular PC.
We take various shortcuts for that. We copy the generic arch setup file over
into the VISWS setup file.
This is the only step that is not expected to boot on a real VISWS.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add early quirks support.
In preparation of enabling the generic architecture to boot on a VISWS.
This will allow us to remove the VISWS subarch and all its complications.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When an interrupt is rerouted to a different I/O APIC pin the relevant
entry of the irq_2_pin list should get updated accordingly so that
operations are performed on the correct redirection entry.
This is already done by the 32-bit variation of the code and here is a
complementing 64-bit implementation. Should make someone's decision less
tough when merging the two. ;)
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit 90221a61a71b7ad659d8741cf1e404506b174982.
This too was just temporary diagnostics - not needed now that we've
got the final fix via:
| commit e2079c4386
| Author: Rafael J. Wysocki <rjw@sisk.pl>
| Date: Tue Jul 8 16:12:26 2008 +0200
|
| x86: fix C1E && nx6325 stability problem
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit a74a1cc3df0be89658bc735c8aed80c8392e2c15.
This was just temporary diagnostics commit - not needed now that we've
got the final fix.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
even on 64bit systems with less than 4G RAM, we can now use fixmap
to handle acpi SIT near end of ram.
change e820_end to e820_end_of_ram again?
or e820_ram_pfn?
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
and let 64-bit to fall back to use fixmap too.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
to avoid warning from find_low_pfn_range for high pages size etc
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/kernel/acpi/boot.c: In function ‘dmi_ignore_irq0_timer_override’:
arch/x86/kernel/acpi/boot.c:1443: error: implicit declaration of function ‘force_mask_ioapic_irq_2’
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The problems are that, with the ACPI vs timer overring issue _fixed_,
after using the box for some time (between several seconds and 1 hour, at
random) processes get very high CPU loads (once I've got X using 107% of
the CPU, for example) and the system becomes unresponsive, as though there
were interrupts lost or something similar.
Andreas Herrman reproduced similar problems:
> Ok, now I've reproduced the stability problem.
> - Using tip/master,
> - reverting e38502eb8aa82314d5ab0eba45f50e6790dadd88 and
> - applying your patch from this posting
> http://marc.info/?l=linux-kernel&m=121539354224562&w=4
>
> Starting X, firefox, gimp, tuxpaint and doing some drawing in tuxpaint
> results in a slow system. Drawing is almost not possible anymore --
> Selections of new colors, cursors etc. is performed with huge delay
> if it's performed at all.
>
> BTW, the code sets up timer IRQ as Virtual Wire IRQ:
>
> Jul 8 14:57:58 kodscha IO-APIC (apicid-pin) 2-22, 2-23 not connected.
> Jul 8 14:57:58 kodscha ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
> Jul 8 14:57:58 kodscha ...trying to set up timer as Virtual Wire IRQ... works.
>
> and both INT0 and INT2 of IOAPIC are masked:
>
> Jul 8 14:57:58 kodscha NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
> Jul 8 14:57:58 kodscha 00 000 1 0 0 0 0 0 0 00
> Jul 8 14:57:58 kodscha 01 003 0 0 0 0 0 1 1 31
> Jul 8 14:57:58 kodscha 02 003 1 0 0 0 0 0 0 30
>
> I've also seen strange CPU utilization -- with syslog-ng:
>
> top - 15:33:06 up 35 min, 4 users, load average: 1.70, 0.68, 0.37
> Tasks: 64 total, 4 running, 60 sleeping, 0 stopped, 0 zombie
> Cpu0 : 0.0%us,100.0%sy, 0.0%ni, 0.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st
> Cpu1 : 6.4%us, 87.2%sy, 0.0%ni, 5.8%id, 0.0%wa, 0.6%hi, 0.0%si, 0.0%st
> Mem: 895384k total, 283568k used, 611816k free, 35492k buffers
> Swap: 1959920k total, 0k used, 1959920k free, 163044k cached
>
> PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
> 4632 root 20 0 17216 800 580 S 104 0.1 0:34.22 syslog-ng
> 28505 root 20 0 205m 11m 4024 S 6 1.3 0:21.16 X
> 28518 root 20 0 56292 5652 4492 S 1 0.6 0:01.80 fluxbox
> 1 root 20 0 3724 608 508 S 0 0.1 0:00.36 init
>
> So far I have no clue why C1E-idle in conjunction with virtual wire
> mode causes this strange behaviour.
>
> ... and I start to think about the root cause of all this.
>
> I've performed similar tests under X with the IRQ0/INT0 configuration and
> I did not see above symptoms.
So lets fall back to the IRQ0/INT0 configuration on this box.
This basically restores the dont-use-the-lapic-timer exception mechanism
that was unconditional on this box prior commit 8750bf5 ("x86: add C1E
aware idle function").
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When system have 4g less ram installed, and acpi table sit
near end of ram, make max_pfn cover them too,
so 64bit kernel don't need to mess up fixmap.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: "Suresh Siddha" <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is for consistency with i386.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is for consistency with i386. We call use_tsc_delay()
at tsc initialization for x86_64, so we'll be always using it.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/smpboot.c: In function 'do_boot_cpu':
arch/x86/kernel/smpboot.c:943: warning: label 'restore_state' defined but not used
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
- order of local variable declarations
- minor code changes
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Acked-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
- local caching of smp_processor_id() in default_do_nmi()
- v2: do not split default_do_nmi over two lines
On Wed, Jul 02, 2008 at 08:12:20PM +0400, Cyrill Gorcunov wrote:
> | -static notrace __kprobes void default_do_nmi(struct pt_regs *regs)
> | +static notrace __kprobes void
> | +default_do_nmi(struct pt_regs *regs)
> | [ ... ]
> | -asmlinkage notrace __kprobes void default_do_nmi(struct pt_regs *regs)
> | +asmlinkage notrace __kprobes void
> | +default_do_nmi(struct pt_regs *regs)
>
> Hi Alexander, good done, thanks! But why did you split default_do_nmi
> definition by two lines? I think it would be better to keep them as it
> was before, ie by a single line
>
> static notrace __kprobes void default_do_nmi(struct pt_regs *regs)
Thanks! Here is the replacement patch with default_do_nmi left on
a single line.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Acked-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
- if (cond) block -> if (!cond) goto end_of_block
- local caching of current
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Acked-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Reorder headers and collect globals in traps_32.c and traps_64.c
Code size and data size are unaffected by the changes. Code
itself is changed due to different ordering of data and bss.
The bss segment changed size due to a change in the packing
of the variables.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Acked-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch does not change the generated object files.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rename the paravirtualized calculate_cpu_khz to calibrate_tsc.
In all cases, we actually calibrate_tsc and use that as the cpu_khz value.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Dan Hecht <dhecht@vmware.com>
Cc: Dan Hecht <dhecht@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Unify the clocksource code.
Unify the tsc_init code.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Dan Hecht <dhecht@vmware.com>
Cc: Dan Hecht <dhecht@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge the tsc calibration code for the 32bit and 64bit kernel.
The paravirtualized calculate_cpu_khz for 64bit now points to the correct
tsc_calibrate code as in 32bit.
Original native_calculate_cpu_khz for 64 bit is now called as calibrate_cpu.
Also moved the recalibrate_cpu_khz function in the common file.
Note that this function is called only from powernow K7 cpu freq driver.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Dan Hecht <dhecht@vmware.com>
Cc: Dan Hecht <dhecht@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move the basic global variable definitions and sched_clock handling in the
common "tsc.c" file.
- Unify notsc kernel command line handling for 32 bit and 64bit.
- Functional changes for 64bit.
- "tsc_disabled" is updated if "notsc" is passed at boottime.
- Fallback to jiffies for sched_clock, incase notsc is passed on
commandline.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Dan Hecht <dhecht@vmware.com>
Cc: Dan Hecht <dhecht@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add lapic resource into kernel resource map and mark it as busy
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
CC: Maciej W. Rozycki <macro@linux-mips.org>
so when it is called after early_param, e820_saved get updated too.
esp for mpc update.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
seperate reserve_setup_data into e820_reserved_setup_data,
and reserve_early_setup_data.
So could use e820_reserved_setup_data to backup e820 with setup_data.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Bernhard Walle <bwalle@suse.de>
Cc: Ying Huang <ying.huang@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so other path that will override memory_setup or
machine_specific_memory_setup could have e820_saved too.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch uses the /sys/firmware/memmap interface provided in the last patch
on the x86 architecture when E820 is used. The patch copies the E820
memory map very early, and registers the E820 map afterwards via
firmware_map_add_early().
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Acked-by: Greg KH <gregkh@suse.de>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: kexec@lists.infradead.org
Cc: yhlu.kernel@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Consistently set _PAGE_GLOBAL in _PAGE_KERNEL flags. This makes 32-
and 64-bit code consistent, and removes some special cases where
__PAGE_KERNEL* did not have _PAGE_GLOBAL set, causing confusion as a
result of the inconsistencies.
This patch only affects x86-64, which generally always supports PGD.
The x86-32 patch is next.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
call it right after we are done with MADT/mptable handling, instead of
doing that in setup_per_cpu_areas() later on...
this way for_possible_cpu() can be used early.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when acpi=off, cpu_to_apicid is ready after get_smp_config
so need to move init_cpu_to_node after it.
otherwise, we will get wrong cpu->node mapping, and it will rely on
amd_detect_cmp() to correct it - but that is too late as
setup_per_cpu_data is already called before that so we will get
per_cpu_data on the wrong node.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
move out e820_register_active_regions from non numa zones_sizes_init()
and remove numa version zones_sizes_init().
and let 32 bit call remove_all_active_ranges() in setup_arch() directly
like 64-bit
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so it has a more meaningful name.
also change it to static.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch removes the need of the crashkernel=...@offset parameter to define
a fixed offset for crashkernel reservation. That feature can be used together
with a relocatable kernel where the kexec-tools relocate the kernel and
get the actual offset from /proc/iomem.
The use case is a kernel where the .text+.data+.bss is after 16M physical
memory (debug kernel with lockdep on x86_64 can cause that) which caused a
major pain in autoconfiguration in our distribution.
Also, that patch unifies crashdump architectures a bit since IA64 has
that semantics from the very beginning of the kdump port.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: vgoyal@redhat.com
Cc: Bernhard Walle <bwalle@suse.de>
Cc: kexec@lists.infradead.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
e820_search_gap also take a end_addr parameter to limit search from
start_addr to end_addr.
Signed-off-by: AloK N Kataria <akataria@vmware.com>
Acked-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: "lenb@kernel.org" <lenb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* When CONFIG_DEBUG_PER_CPU_MAPS is set, the node passed to
node_to_cpumask and node_to_cpumask_ptr should be validated.
If invalid, then a dump_stack is performed and a zero cpumask
is returned.
v2: Slightly different version to remove a compiler warning.
v3: Redone to reflect moving setup.c -> setup_percpu.c
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: "akpm@linux-foundation.org" <akpm@linux-foundation.org>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar wrote:
> -tip auto-testing found pagetable corruption (CPA self-test failure):
>
> [ 32.956015] CPA self-test:
> [ 32.958822] 4k 2048 large 508 gb 0 x 2556[ffff880000000000-ffff88003fe00000] miss 0
> [ 32.964000] CPA ffff88001d54e000: bad pte 1d4000e3
> [ 32.968000] CPA ffff88001d54e000: unexpected level 2
> [ 32.972000] CPA ffff880022c5d000: bad pte 22c000e3
> [ 32.976000] CPA ffff880022c5d000: unexpected level 2
> [ 32.980000] CPA ffff8800200ce000: bad pte 200000e3
> [ 32.984000] CPA ffff8800200ce000: unexpected level 2
> [ 32.988000] CPA ffff8800210f0000: bad pte 210000e3
>
> config and full log can be found at:
>
> http://redhat.com/~mingo/misc/config-Mon_Jun_30_11_11_51_CEST_2008.bad
> http://redhat.com/~mingo/misc/log-Mon_Jun_30_11_11_51_CEST_2008.bad
Phew. OK, I've worked this out. Short version is that's it's a false
alarm, and there was no real failure here. Long version:
* I changed the code to create the physical mapping pagetables to
reuse any existing mapping rather than replace it. Specifically,
reusing an pud pointed to by the pgd caused this symptom to appear.
* The specific PUD being reused is the one created statically in
head_64.S, which creates an initial 1GB mapping.
* That mapping doesn't have _PAGE_GLOBAL set on it, due to the
inconsistency between __PAGE_* and PAGE_*.
* The CPA test attempts to clear _PAGE_GLOBAL, and then checks to
see that the resulting range is 1) shattered into 4k pages, and 2)
has no _PAGE_GLOBAL.
* However, since it didn't have _PAGE_GLOBAL on that range to start
with, change_page_attr_clear() had nothing to do, and didn't
bother shattering the range,
* resulting in the reported messages
The simple fix is to set _PAGE_GLOBAL in level2_ident_pgt.
An additional fix to make CPA testing more robust by using some other
pagetable bit (one of the unused available-to-software ones). This
would solve spurious CPA test warnings under Xen which uses _PAGE_GLOBAL
for its own purposes (ie, not under guest control).
Also, we should revisit the use of _PAGE_GLOBAL in asm-x86/pgtable.h,
and use it consistently, and drop MAKE_GLOBAL. The first time I
proposed it it caused breakages in the very early CPA code; with luck
that's all fixed now.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ying Huang would like setup_data to be reserved, but not included in the
no save range.
Here we try to modify the e820 table to reserve that range early.
also add that in early_res in case bootloader messes up with the ramdisk.
other solution would be
1. add early_res_to_highmem...
2. early_res_to_e820...
but they could reserve another type memory wrongly, if early_res has some
resource reserved early, and not needed later, but it is not removed from
early_res in time. Like the RAMDISK (already handled).
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: andi@firstfloor.org
Tested-by: Huang, Ying <ying.huang@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Looks like the setup.c unification missed the early_ioremap init from
the early_ioremap unification. Unconditionally call early_ioremap_init().
needed for "x86/paravirt: groundwork for 64-bit Xen support".
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
change the enable_local_apic to static force_enable_local_apic for 32bit
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when 64bit resource is not enabled, we get:
arch/x86/kernel/e820.c: In function ‘e820_reserve_resources’:
arch/x86/kernel/e820.c:1217: warning: comparison is always false due to limited range of data type
because res->start/end is resource_t aka u32. it will overflow.
fix it with temp end of u64
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
instead of calling it from trap_init()
also move init ioapic mapping out of apic_32.c
so 32 bit do same as 64 bit
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
do that in init_memory_mapping
also remove one init_ohci1394_dma_on_all_controllers
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
asm-x86/paravirt.h already have protection with CONFIG_PARAVIRT inside
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch brings back limiting of the E820 map when a user-defined
E820 map is specified. While the behaviour of i386 (32 bit) was to limit
the E820 map (and /proc/iomem), the behaviour of x86-64 (64 bit) was not to
limit.
That patch limits the E820 map again for both x86 architectures.
Code was tested for compilation and booting on a 32 bit and 64 bit system.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Acked-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: kexec@lists.infradead.org
Cc: vgoyal@redhat.com
Cc: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
64-bit Xen pushes a couple of extra words onto an exception frame.
Add a hook to deal with them.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In a 64-bit system, we need separate sysret/sysexit operations to
return to a 32-bit userspace.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citirx.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There's no need to combine restoring the user rsp within the sysret
pvop, so split it out. This makes the pvop's semantics closer to the
machine instruction.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citirx.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Don't conflate sysret and sysexit; they're different instructions with
different semantics, and may be in use at the same time (at least
within the same kernel, depending on whether its an Intel or AMD
system).
sysexit - just return to userspace, does no register restoration of
any kind; must explicitly atomically enable interrupts.
sysret - reloads flags from r11, so no need to explicitly enable
interrupts on 64-bit, responsible for restoring usermode %gs
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citirx.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is needed when the kernel is running on RING3, such as under Xen.
x86_64 has a weird feature that makes it #GP on iret when SS is a null
descriptor.
This need to be tested on bare metal to make sure it doesn't cause any
problems. AMD specs say SS is always ignored (except on iret?).
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We must do this because load_TLS() may need to clear %fs and %gs.
(e.g. under Xen).
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We must leave lazy mode before switching the %fs and %gs selectors.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Split x86_64_start_kernel() into two pieces:
The first essentially cleans up after head_64.S. It clears the
bss, zaps low identity mappings, sets up some early exception
handlers.
The second part preserves the boot data, reserves the kernel's
text/data/bss, pagetables and ramdisk, and then starts the kernel
proper.
This split is so that Xen can call the second part to do the set up it
needs done. It doesn't need any of the first part setups, because it
doesn't boot via head_64.S, and its redundant or actively damaging.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Set __PAGE_OFFSET to the most negative possible address +
16*PGDIR_SIZE. The gap is to allow a space for a hypervisor to fit.
The gap is more or less arbitrary, but it's what Xen needs.
When booting native, kernel/head_64.S has a set of compile-time
generated pagetables used at boot time. This patch removes their
absolutely hard-coded layout, and makes it parameterised on
__PAGE_OFFSET (and __START_KERNEL_map).
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add hooks which are called at pgd_alloc/free time. The pgd_alloc hook
may return an error code, which if non-zero, causes the pgd allocation
to be failed. The hooks may be used to allocate/free auxillary
per-pgd information.
also fix:
> * Ingo Molnar <mingo@elte.hu> wrote:
>
> include/asm/pgalloc.h: In function ‘paravirt_pgd_free':
> include/asm/pgalloc.h:14: error: parameter name omitted
> arch/x86/kernel/entry_64.S: In file included from
> arch/x86/kernel/traps_64.c:51:include/asm/pgalloc.h: In function ‘paravirt_pgd_free':
> include/asm/pgalloc.h:14: error: parameter name omitted
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
In file included from arch/x86/kernel/setup.c:118:
include/asm/highmem.h:64: error: expected identifier or ‘(' before ‘do'
include/asm/highmem.h:64: error: expected identifier or ‘(' before ‘while'
include/asm/highmem.h:67: error: expected identifier or ‘(' before ‘do'
include/asm/highmem.h:67: error: expected identifier or ‘(' before ‘while'
Signed-off-by: Ingo Molnar <mingo@elte.hu>
