[ Upstream commit 48171d0ea7caccf21c9ee3ae75eb370f2a756062 ]
I noticed that we can get a -EREMOTEIO errors on at least omap4 duovero:
twl6040 0-004b: Failed to write 2d = 19: -121
And then any following register access will produce errors.
There 2d offset above is register ACCCTL that gets written on twl6040
powerup. With error checking added to the related regcache_sync() call,
the -EREMOTEIO error is reproducable on twl6040 powerup at least
duovero.
To fix the error, we need to wait until twl6040 is accessible after the
powerup. Based on tests on omap4 duovero, we need to wait over 8ms after
powerup before register write will complete without failures. Let's also
make sure we warn about possible errors too.
Note that we have twl6040_patch[] reg_sequence with the ACCCTL register
configuration and regcache_sync() will write the new value to ACCCTL.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e364e87ad7f2c636276c773d718cda29d62b741 ]
MODULE_DEVICE_TABLE(of, <of_match_table> should be called to complete DT
OF mathing mechanism and register it.
Before this patch:
modinfo drivers/mfd/tps65912-spi.ko | grep alias
alias: spi:tps65912
After this patch:
modinfo drivers/mfd/tps65912-spi.ko | grep alias
alias: of:N*T*Cti,tps65912C*
alias: of:N*T*Cti,tps65912
alias: spi:tps65912
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20bb907f7dc82ecc9e135ad7067ac7eb69c81222 ]
Since commit 6e2bd956936 ("i2c: omap: Use noirq system sleep pm ops to idle device for suspend")
on gta04 we have handle_twl4030_pih() called in situations where pm_runtime_get()
in i2c-omap.c returns -EACCES.
[ 86.474365] Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
[ 86.485473] printk: Suspending console(s) (use no_console_suspend to debug)
[ 86.555572] Disabling non-boot CPUs ...
[ 86.555664] Successfully put all powerdomains to target state
[ 86.563720] twl: Read failed (mod 1, reg 0x01 count 1)
[ 86.563751] twl4030: I2C error -13 reading PIH ISR
[ 86.563812] twl: Read failed (mod 1, reg 0x01 count 1)
[ 86.563812] twl4030: I2C error -13 reading PIH ISR
[ 86.563873] twl: Read failed (mod 1, reg 0x01 count 1)
[ 86.563903] twl4030: I2C error -13 reading PIH ISR
This happens when we wakeup via something behing twl4030 (powerbutton or rtc
alarm). This goes on for minutes until the system is finally resumed.
Disable the irq on suspend and enable it on resume to avoid
having i2c access problems when the irq registers are checked.
Fixes: 6e2bd956936 ("i2c: omap: Use noirq system sleep pm ops to idle device for suspend")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ae7b8eda27b33b1f688dfdebe4d46f690a8f9162 upstream.
There is a potential NULL pointer dereference in case devm_kzalloc()
fails and returns NULL.
Fix this by adding a NULL check on *lookup*
This bug was detected with the help of Coccinelle.
Fixes: b2e6355559 ("i2c: gpio: Convert to use descriptors")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9e28989d41c0eab57ec0bb156617a8757406ff8a ]
When mc13xxx_reg_read() fails, "old_adc0" is uninitialized and will
contain random value. Further execution uses "old_adc0" even when
mc13xxx_reg_read() fails.
The fix checks the return value of mc13xxx_reg_read(), and exits
the execution when it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75d4c5e03c2ae9902ab521024b10291f6fc9515b ]
Use devm_regmap_add_irq_chip and clean up error path in probe
and also the remove function.
Reported-by: Christian Hohnstaedt <Christian.Hohnstaedt@wago.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18e294ddafaeb80a1e2e10c9bd750a6cb8388d5b ]
The driver adds different MFD child devices via mfd_add_devices() and
hence it is required to call mfd_remove_devices() to remove MFD child
devices.
Fixes: 5e0115581b ("cros_ec: Move cros_ec_dev module to drivers/mfd")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea90e7b47f0a8bd2fe14e9a88f523de7c67db90a ]
Parts of the AXP803 are compatible with their counterparts on the AXP813.
These include the GPIO, ADC, AC and battery power supplies.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 753a8d083e085c6f552c7982749de4cc7c40e2ac ]
In the axp20x driver, the various mfd_cell lists had varying amounts
of indentation, sometimes even within the same list. For the axp288,
there's no alignment at all.
Re-align the right hand side of the assignments with the least amount
of tabs possible. Also collapse the closing bracket and the opening
bracket of the next entry onto the same line for the axp288, to be
consistent with all the other mfd_cell lists.
This patch is whitespace change only. No functionality is modified.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 504e4175829c44328773b96ad9c538e4783a8d22 ]
This is required as part of the initialization sequence on certain SoCs.
If these registers are not initialized, the hardware can be unresponsive.
This fixes the driver on apq8060 (HP TouchPad device).
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0aff01e7aa6ad2d6998ef1323843212d1db8b04 ]
Because BD9571MWV_DVFS_MONIVDAC is not defined in the volatile table,
the physical register value is not updated by regmap and DVFS doesn't
work as expected. Fix it!
Fixes: d3ea212720 ("mfd: Add ROHM BD9571MWV-M MFD PMIC driver")
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
[wsa: rebase, add 'Fixes', reword commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10628e3ecf544fa2e4e24f8e112d95c37884dc98 ]
This function is supposed to return zero on success or negative error
codes on error. Unfortunately, there is a bug so it sometimes returns
non-zero, positive numbers on success.
I noticed this bug during review and I can't test it. It does appear
that the return is sometimes propogated back to _regmap_read() where all
non-zero returns are treated as failure so this may affect run time.
Fixes: 47c1697508 ("mfd: Align ab8500 with the abx500 interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a177276aa098aa47a100d51a13eaaef029604b6d ]
If the PMIC ID is unknown, the current code would call
irq_domain_remove and panic, as pmic->irq_domain is only
initialized by mt6397_irq_init.
Return immediately with an error, if the chip ID is unsupported.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a3888f62fe66429fad3be7f2ba962e1e08c26fd6 ]
When building the kernel with Clang, the following section mismatch
warnings appear:
WARNING: vmlinux.o(.text+0x7239cc): Section mismatch in reference from
the function db8500_prcmu_probe() to the function
.init.text:init_prcm_registers()
The function db8500_prcmu_probe() references
the function __init init_prcm_registers().
This is often because db8500_prcmu_probe lacks a __init
annotation or the annotation of init_prcm_registers is wrong.
WARNING: vmlinux.o(.text+0x723e28): Section mismatch in reference from
the function db8500_prcmu_probe() to the function
.init.text:fw_project_name()
The function db8500_prcmu_probe() references
the function __init fw_project_name().
This is often because db8500_prcmu_probe lacks a __init
annotation or the annotation of fw_project_name is wrong.
db8500_prcmu_probe should not be marked as __init so remove the __init
annotation from fw_project_name and init_prcm_registers.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8838555089f0345b87f4277fe5a8dd647dc65589 ]
When building the kernel with Clang, the following section mismatch
warning appears:
WARNING: vmlinux.o(.text+0x3d84a3b): Section mismatch in reference from
the function twl_probe() to the function
.init.text:unprotect_pm_master()
The function twl_probe() references
the function __init unprotect_pm_master().
This is often because twl_probe lacks a __init
annotation or the annotation of unprotect_pm_master is wrong.
Remove the __init annotation on the *protect_pm_master functions so
there is no more mismatch.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b40ee006fe6a8a25093434e5d394128c356a48f3 ]
Use PLATFORM_DEVID_AUTO to number mfd cells while registering, so that
different instances are uniquely identified. This is required in order
to support registering of multiple instances of same ti_am335x_tscadc IP.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ac4ca4b9f4623ba5e1ea7a582f286567c611e027 upstream.
The tps6586x driver creates an irqchip that is used by its various child
devices for managing interrupts. The tps6586x-rtc device is one of its
children that uses the tps6586x irqchip. When using the tps6586x-rtc as
a wake-up device from suspend, the following is seen:
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.001 seconds) done.
OOM killer disabled.
Freezing remaining freezable tasks ... (elapsed 0.000 seconds) done.
Disabling non-boot CPUs ...
Entering suspend state LP1
Enabling non-boot CPUs ...
CPU1 is up
tps6586x 3-0034: failed to read interrupt status
tps6586x 3-0034: failed to read interrupt status
The reason why the tps6586x interrupt status cannot be read is because
the tps6586x interrupt is not masked during suspend and when the
tps6586x-rtc interrupt occurs, to wake-up the device, the interrupt is
seen before the i2c controller has been resumed in order to read the
tps6586x interrupt status.
The tps6586x-rtc driver sets it's interrupt as a wake-up source during
suspend, which gets propagated to the parent tps6586x interrupt.
However, the tps6586x-rtc driver cannot disable it's interrupt during
suspend otherwise we would never be woken up and so the tps6586x must
disable it's interrupt instead.
Prevent the tps6586x interrupt handler from executing on exiting suspend
before the i2c controller has been resumed by disabling the tps6586x
interrupt on entering suspend and re-enabling it on resuming from
suspend.
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48a2ca0ee3994df53da230c7079a18a70ec914f9 upstream.
This reverts commit 3aa2177e47.
That commit triggered a new WARN when unloading the module (see at the
end of the commit message). When a class_dev is embedded in a structure
then that class_dev is the thing that controls the lifetime of that
structure, for that reason device managed allocations can't be used here.
See Documentation/kobject.txt.
Revert the above patch, so the struct is allocated using kzalloc and we
have a release function for it that frees the allocated memory, otherwise
it is broken.
------------[ cut here ]------------
Device 'cros_ec' does not have a release() function, it is broken and must be fixed.
WARNING: CPU: 3 PID: 3675 at drivers/base/core.c:895 device_release+0x80/0x90
Modules linked in: btusb btrtl btintel btbcm bluetooth ...
CPU: 3 PID: 3675 Comm: rmmod Not tainted 4.20.0-rc4 #76
Hardware name: Google Kevin (DT)
pstate: 40000005 (nZcv daif -PAN -UAO)
pc : device_release+0x80/0x90
lr : device_release+0x80/0x90
sp : ffff00000c47bc70
x29: ffff00000c47bc70 x28: ffff8000e86b0d40
x27: 0000000000000000 x26: 0000000000000000
x25: 0000000056000000 x24: 0000000000000015
x23: ffff8000f0bbf860 x22: ffff000000d320a0
x21: ffff8000ee93e100 x20: ffff8000ed931428
x19: ffff8000ed931418 x18: 0000000000000020
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000400 x14: 0000000000000143
x13: 0000000000000000 x12: 0000000000000400
x11: 0000000000000157 x10: 0000000000000960
x9 : ffff00000c47b9b0 x8 : ffff8000e86b1700
x7 : 0000000000000000 x6 : ffff8000f7d520b8
x5 : ffff8000f7d520b8 x4 : 0000000000000000
x3 : ffff8000f7d58e68 x2 : ffff8000e86b0d40
x1 : 37d859939c964800 x0 : 0000000000000000
Call trace:
device_release+0x80/0x90
kobject_put+0x74/0xe8
device_unregister+0x20/0x30
ec_device_remove+0x34/0x48 [cros_ec_dev]
platform_drv_remove+0x28/0x48
device_release_driver_internal+0x1a8/0x240
driver_detach+0x40/0x80
bus_remove_driver+0x54/0xa8
driver_unregister+0x2c/0x58
platform_driver_unregister+0x10/0x18
cros_ec_dev_exit+0x1c/0x2d8 [cros_ec_dev]
__arm64_sys_delete_module+0x16c/0x1f8
el0_svc_common+0x84/0xd8
el0_svc_handler+0x2c/0x80
el0_svc+0x8/0xc
---[ end trace a57c4625f3c60ae8 ]---
Cc: stable@vger.kernel.org
Fixes: 3aa2177e47 ("mfd: cros_ec: Use devm_kzalloc for private data")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9612f8f503804d2fd2f63aa6ba1e58bba4612d96 ]
The IRQ work is added before the struct rtc is allocated and registered,
but this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.
Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
before calling menelaus_add_irq_work.
Also, this solves a possible leak as the RTC is never released.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It currently only works if the parent bus uses "simple-bus". We
currently try to probe children with non-existing compatible values.
And we're missing .probe.
I noticed this while testing devices configured to probe using ti-sysc
interconnect target module driver. For that we also may want to rebind
the driver, so let's remove __init and __exit.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull i2c updates from Wolfram Sang:
- the core has now a lockless variant of i2c_smbus_xfer. Some open
coded versions of this got removed in drivers. This also enables
proper SCCB support in regmap.
- locking got a more precise naming. i2c_{un}lock_adapter() had to go,
and we know use i2c_lock_bus() consistently with flags like
I2C_LOCK_ROOT_ADAPTER and I2C_LOCK_SEGMENT to avoid ambiguity.
- the gpio fault injector got a new delicate testcase
- the bus recovery procedure got fixed to handle the new testcase
correctly
- a new quirk flag for controllers not able to handle zero length
messages together with driver updates to use it
- new drivers: FSI bus attached I2C masters, GENI I2C controller, Owl
family S900
- and a good set of driver improvements and bugfixes
* 'i2c/for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (77 commits)
i2c: rcar: implement STOP and REP_START according to docs
i2c: rcar: refactor private flags
i2c: core: ACPI: Make acpi_gsb_i2c_read_bytes() check i2c_transfer return value
i2c: core: ACPI: Properly set status byte to 0 for multi-byte writes
dt-bindings: i2c: rcar: Add r8a774a1 support
dt-bindings: i2c: sh_mobile: Add r8a774a1 support
i2c: imx: Simplify stopped state tracking
i2c: imx: Fix race condition in dma read
i2c: pasemi: remove hardcoded bus numbers on smbus
i2c: designware: Add SPDX license tag
i2c: designware: Convert to use struct i2c_timings
i2c: core: Parse SDA hold time from firmware
i2c: designware-pcidrv: Mark expected switch fall-through
i2c: amd8111: Mark expected switch fall-through
i2c: sh_mobile: use core to detect 'no zero length read' quirk
i2c: xlr: use core to detect 'no zero length' quirk
i2c: rcar: use core to detect 'no zero length' quirk
i2c: stu300: use core to detect 'no zero length' quirk
i2c: pmcmsp: use core to detect 'no zero length' quirk
i2c: mxs: use core to detect 'no zero length' quirk
...
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
- New Device Support
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
- New Functionality
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
- Fix-ups
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
- Bug Fixes
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501
-----BEGIN PGP SIGNATURE-----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=4Yj4
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
New Device Support:
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
New Functionality:
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
Fix-upsL
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
Bug Fixes:
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501"
* tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (60 commits)
mfd: madera: Add register definitions for accessory detect
mfd: sm501: Set coherent_dma_mask when creating subdevices
mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC
mfd: bd71837: Core driver for ROHM BD71837 PMIC
media: platform: cros-ec-cec: Fix dependency on MFD_CROS_EC
mfd: sec-core: Export OF module alias table
mfd: as3722: Disable auto-power-on when AC OK
mfd: axp20x: Support AXP806 in I2C mode
mfd: axp20x: Add self-working mode support for AXP806
dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806
mfd: wm8994: Allow to configure CS/ADDR Pulldown from dts
mfd: wm8994: Allow to configure Speaker Mode Pullup from dts
mfd: rave-sp: Emulate CMD_GET_STATUS on device that don't support it
mfd: rave-sp: Add legacy watchdog ping command translation
mfd: rave-sp: Add legacy EEPROM access command translation
mfd: rave-sp: Initialize flow control and parity of the port
mfd: rave-sp: Fix incorrectly specified checksum type
mfd: rave-sp: Remove unused defines
mfd: hi655x: Fix regmap area declared size for hi655x
mfd: ti_am335x_tscadc: Fix struct clk memory leak
...
ROHM BD71837 PMIC MFD driver providing interrupts and support
for three subsystems:
- clk
- Regulators
- input/power-key
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In case of Device Tree platforms, even though the Samsung PMIC sec
device is instantiated from DT, the driver is still matched through I2C
module alias. That is because I2C core always reports an I2C module
alias instead of DT one.
This could change in the future so export DT module alias.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On ams AS3722, power on when AC OK is enabled by default.
Making this option as disable by default and enable only
when platform need this explicitly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Bibek Basu <bbasu@nvidia.com>
Tested-by: Bibek Basu <bbasu@nvidia.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Pine64 H64 board uses an AXP806 PMIC in I2C and self-working mode.
The H64 SoC does not have the usual RSB controller.
This patch adds AXP806 to the list of devices supported in I2C mode.
In theory, all RSB-based PMICs can also be used in I2C mode.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP806 can operate in a standalone "self-working" mode, in which it
is also responsible for power control of the overall system. This mode
is similar to the master mode, but the EN/PWRON pin functions as a power
button, instead of a level-triggered enable switch.
This patch adds code checking for the new "x-powers,self-working-mode"
property, and a separate mfd_cell list that includes the power button
(PEK) sub-device.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For designs where CS/ADDR pin is floating, it is useful to
allow dts to define whether to keep internal pull down or not.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Configuring Speaker Mode Pullup was already supported in pdata, but not
in the dts.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
CMD_GET_STATUS is not supported by some devices implementing
RDU2-compatible ICD as well as "legacy" devices. To account for that
fact, add code that obtains the same information (app/bootloader FW
version) using several different commands.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is needed to make rave-sp-wdt driver to properly ping the
watchdog on "legacy" firmware.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is needed to make rave-sp-eeprom driver work on "legacy"
firmware.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Relying on serial port defaults for flow control and parity can result
in complete breakdown of communication with RAVE SP on some platforms
where defaults are not what we need them to be. One such case is
VF610-base ZII SPU3 board (not supported upstream). To avoid this
problem in the future, add code to explicitly configure both.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove unusded defines that are a leftover from earlier iterations of
the driver.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixes https://bugs.linaro.org/show_bug.cgi?id=3903
LTP Functional tests have caused a bad paging request when triggering
the regmap_read_debugfs() logic of the device PMIC Hi6553 (reading
regmap/f8000000.pmic/registers file during read_all test):
Unable to handle kernel paging request at virtual address ffff0
[ffff00000984e000] pgd=0000000077ffe803, pud=0000000077ffd803,0
Internal error: Oops: 96000007 [#1] SMP
...
Hardware name: HiKey Development Board (DT)
...
Call trace:
regmap_mmio_read8+0x24/0x40
regmap_mmio_read+0x48/0x70
_regmap_bus_reg_read+0x38/0x48
_regmap_read+0x68/0x170
regmap_read+0x50/0x78
regmap_read_debugfs+0x1a0/0x308
regmap_map_read_file+0x48/0x58
full_proxy_read+0x68/0x98
__vfs_read+0x48/0x80
vfs_read+0x94/0x150
SyS_read+0x6c/0xd8
el0_svc_naked+0x30/0x34
Code: aa1e03e0 d503201f f9400280 8b334000 (39400000)
Investigations have showed that, when triggered by debugfs read()
handler, the mmio regmap logic was reading a bigger (16k) register area
than the one mapped by devm_ioremap_resource() during hi655x-pmic probe
time (4k).
This commit changes hi655x's max register, according to HW specs, to be
the same as the one declared in the pmic device in hi6220's dts, fixing
the issue.
Cc: <stable@vger.kernel.org> #v4.9 #v4.14 #v4.16 #v4.17
Signed-off-by: Rafael David Tinoco <rafael.tinoco@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some Arizona CODECs have a small timing window where they will
NAK an I2C transaction if it happens before the boot done bit is
set. This can cause the read of the register containing the boot
done bit to fail until it is set. Since regmap_read_poll_timeout
will abort polling if a read fails it can't be reliably used to
poll the boot done bit over I2C.
Do a partial revert of ef84f885e0 ("mfd: arizona: Refactor
arizona_poll_reg"), removing the regmap_read_poll_timeout but
leaving the refactoring to make the arizona_poll_reg take more
sensible arguments.
Fixes: ef84f885e0 ("mfd: arizona: Refactor arizona_poll_reg")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Ice Lake has the same LPSS than Intel Cannon Lake. Add the new IDs
to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For some errors, the wm8994_device_init function was returning or
jumping to the wrong point in the error path.
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add const to the declaration of various local variables of type
kempld_platform_data for which the referenced value is always only
dereferenced or passed to a const parameter, to record the fact that
kempld_platform_data_generic is declared as const.
The semantic match that finds this issue is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier i,j;
@@
const struct i j = { ... };
@ok@
identifier r.i;
position p;
@@
const struct i@p *
@@
identifier r.i;
position p != ok.p;
@@
* struct i@p *
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Immutable Branch which moves the cros_ec_i2c and cros_ec_spi
transport drivers from mfd to platform/chrome. Changes in arm are a simple
rename in defconfigs. Change in input is a rename in help text.
-----BEGIN PGP SIGNATURE-----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=EhHj
-----END PGP SIGNATURE-----
Merge branches 'ib-mfd-4.19', 'ib-mfd-gpio-pinctrl-4.19', 'ib-mfd-i915-media-platform-4.19' and 'ib-mfd-regulator-4.19', tag 'ib-platform-chrome-mfd-move-cros-ec-transport-for-4.19' into ibs-for-mfd-merged
Immutable branch (mfd, chrome) due for the v4.19 window
Immutable Branch which moves the cros_ec_i2c and cros_ec_spi
transport drivers from mfd to platform/chrome. Changes in arm are a simple
rename in defconfigs. Change in input is a rename in help text.
The EC can expose a CEC bus, thus add the cros-ec-cec MFD sub-device
when the CEC feature bit is present.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Locking the root adapter for __i2c_transfer will deadlock if the
device sits behind a mux-locked I2C mux. Switch to the finer-grained
i2c_lock_bus with the I2C_LOCK_SEGMENT flag. If the device does not
sit behind a mux-locked mux, the two locking variants are equivalent.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
