wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This 'legacy' OMAP2420 McBSP2 muxing code is currently broken after recent
conversion to new mux code. The omap_mcbsp_request calling this code is
usually called after booting whereas the omap_mux_init_signal is __init
marked so null pointer dereference would occur.
Fix this by removing the muxing code and let the bootloader or board file to
do it if necessary. Remove also omap2_mcbsp_ops as there is no use for it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP SRG (Sample Rate Generator) and FSG (Frame Sync
Generator) is only needed to be enabled, when McBSP
is master.
In McBSP slave mode, the SRG, and FSG can be kept disabled,
which might save some power at the end in this configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Updates to enable omap aes
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
[tony@atomide.com: updated to use CONFIG_ARCH_OMAP2/3 instead of old 24XX/34XX]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix this and similar build warnings when building with
omap_4430sdp_defconfig.
CC arch/arm/mach-omap2/board-4430sdp.o
In file included from arch/arm/mach-omap2/board-4430sdp.c:36:
arch/arm/plat-omap/include/plat/usb.h:109: warning: return type defaults to 'int'
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Bootloader on Nokia N800 and N810 muxes I2C codec port pins for EAC block.
As there is no driver and use for EAC, mux those pins for McBSP instead
since N810 ASoC drivers can use it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Second i2c bus on Nokia N800 and N810 shares both common and hw specific
peripherals. Register now this bus and add board info with tlv320aic3x for
N810. Common peripherals may be added as an additional board info to
omap_register_i2c_bus(2, ...);
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Move n8x0_i2c_board_info_1 out from #ifdef CONFIG_MENELAUS block,
register i2c1 in n8x0_init_machine and do a few clean-ups around these.
Code looks better if board infos are grouped together
- Mark n8x0_i2c_board_info_1 and n8x0_menelaus_platform_data with __initdata
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes these compiler warnings:
CC arch/arm/mach-omap2/mux.o
arch/arm/mach-omap2/mux.c: In function 'omap_mux_init_gpio':
arch/arm/mach-omap2/mux.c:90: warning: 'gpio_mux' may be used uninitial
ized in this function
CC arch/arm/plat-omap/gpio.o
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_resume_after_idle':
arch/arm/plat-omap/gpio.c:2152: warning: 'l' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_prepare_for_idle':
arch/arm/plat-omap/gpio.c:2085: warning: 'l2' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c:2085: warning: 'l1' may be used uninitialized
in this function
CC arch/arm/mach-omap2/board-omap4panda.o
arch/arm/mach-omap2/board-omap4panda.c: In function 'omap4_panda_init':
arch/arm/mach-omap2/board-omap4panda.c:277: warning: unused variable 's
tatus'
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If a GPIO bank has more than one GPIO with debounce enabled, the
debounce clock will not be fully disabled before going to
idle/suspend.
In the idle path, we just do a single clk_disable() of the bank's
debounce clock. If there are multiple debounce-enabled GPIOs in the
bank, that clocks usage count will be > 1, so the clk_disable() will
not actually disable the clock.
So the fix is to clk_disable() for every debounce-enabled GPIO in the
bank (and an equivalent clk_enable() of course.)
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The OMAP4 L3 interconnect is split in 3 part for power saving reason.
Because of that there is no l3_main like on OMAP2 & 3 but 3 differentes
l3_main_X instances.
In the case of OMAP4, query only the l3_main_1 part. The clock and
voltage are shared across the 3 instances.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The current version contains only the interconnects and the
mpu hwmods.
The remaining hwmods will be introduced by further patches on
top of this one.
- enable as well omap_hwmod.c build for OMAP4 Soc
Please not that this file uses the new naming convention for
naming HW IPs. This convention will be backported soon for previous
OMAP2 & 3 data files.
new name trm name
------------- -------------------
counter_32k synctimer_32k
l3_main l3
timerX gptimerX / dmtimerX
mmcX mmchsX / sdmmcX
dma_system sdma
smartreflex_X sr_X / sr?
usb_host_fs usbfshost
usb_otg_hs hsusbotg
usb_tll_hs usbtllhs_config
wd_timerX wdtimerX
ipu cortexm3 / ducati
dsp c6x / tesla
iva ivahd / iva2.2
kbd kbdocp / keyboard
mailbox system_mailbox
mpu cortexa9 / chiron
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In order to help differentiate omap_devices from normal
platform_devices, make them all a parent of a new common parent
device.
Then, in order to determine if a platform_device is also an
omap_device, checking the parent is all that is needed.
Users of this feature are the runtime PM core for OMAP, where we need
to know if a device being passed in is an omap_device or not in order
to know whether to call the omap_device API with it.
In addition, all omap_devices will now show up under /sys/devices/omap
instead of /sys/devices/platform
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This reverts commit 0007122ad8.
The dereference method of checking for a valid omap_device when
wrapping a platform_device is rather unsafe and dangerous.
Instead, a better way of checking for a valid omap-device is
to use a common parent device for all omap_devices, then a check
can simply be made using the device parent. The only user of this
API was the initial version of the runtime PM core for OMAP. This
has now been switched to check device parent, so there are no more
users of this API.
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When the clockdomain layer initializes, place all clockdomains into
software-supervised mode, and clear all wakeup and sleep dependencies
immediately, rather than waiting for the PM code to do this later.
This fixes a major bug where critical sleep dependencies added by the
hwmod code are cleared during late PM init.
As a side benefit, the _init_{wk,sleep}dep_usecount() functions are no
longer needed, so remove them.
Kevin Hilman <khilman@deeprootsystems.com> did all the really hard work on
this, identifying the problem and finding the bug.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The set_pwrdm_state() is needed on omap4 as well so move
this routine to common pm.c file so that it's available for omap3/4
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Commit 8e2efde9 added milliseconds suspend wakeup time support but
same interface is not exported through debugfs
This patch enables the debugfs hook for wakeup_timer_milliseconds
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch moves omap2_pm_wakeup_on_timer() and pm debug entries
form pm34xx.c to pm-debug.c and export it, so that it is available
to other OMAPs
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP4 has an iva device and a dsp devcice where as OMAP2/3
has only an iva device. In this file the iva device in the
system is registered under the name dsp_dev and the API
to retrieve the iva device is omap2_get_dsp_device.
This patch renames the dsp_dev to iva_dev, renames
omap2_get_dsp_device to omap2_get_iva_device,
registers dsp_dev for OMAP4 and adds a new API
omap4_get_dsp_device to retrieve the dep_dev.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In an effort to simplify the core idle path, move any device-specific
special case handling from the core PM idle path into the CPUidle
pre-idle checking path.
This keeps the core, interrupts-disabled idle path streamlined and
independent of any device-specific handling, and also allows CPUidle
to do the checking only for certain C-states as needed. This patch
has the device checks in place for all states with the CHECK_BM flag,
namely all states >= C2.
This patch was inspired by a similar patch written by Tero Kristo as
part of a larger series to add INACTIVE state support.
NOTE: This is a baby-step towards decoupling device idle (or system
idle) from CPU idle. Eventually, CPUidle should only manage the CPU,
and device/system idle should be managed elsewhere.
Cc: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This change adds in MMC and I2C support to the HTC Herald board, as well
as adding the HTCPLD driver for the PLD used on this phone. It also
adds in the gpio-keys entries for the front directional keys and
selector and the cursor keys on the slide-out keyboard, and gpio-leds
support for the LEDs attached to the htcpld.
Additionally, SPI bus support (using the spi100k driver) and
touchscreen support (using the ads7846 driver) were added.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch:
- adds more documentation to the hwmod code
- fixes some documentation typos elsewhere in the file
- changes the _sysc_*() function names to appear in (verb, noun) order,
to match the rest of the function names.
This patch should not result in any functional change.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Benoît Cousson <b-cousson@ti.com>
For every optional clock present per hwmod per omap-device, this function
adds an entry in the clocks list of the form <dev-id=dev_name, con-id=role>,
if an entry is already present in the list of the form <dev-id=NULL, con-id=role>.
The function is called from within the framework inside omap_device_build_ss(),
after omap_device_register.
This allows drivers to get a pointer to its optional clocks based on its role
by calling clk_get(<dev*>, <role>).
Link to discussions related to this patch:
http://www.spinics.net/lists/linux-omap/msg34809.html
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: simplified loop iterator; removed the superfluous clk_get(),
using the clk_get() in clk_add_alias() instead]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
If a module's OCP slave port is programmed to be in smartidle,
its also necessary that they have module level wakeup enabled.
Update _sysc_enable in hwmod framework to do this.
The thread "[PATCH 7/8] : Hwmod api changes" archived here:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg34212.html
has additional technical information on the rationale of this patch.
Sergei Shtylyov <sshtylyov@mvista.com> identified an indentation
problem with this patch - thanks, Sergei.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
[paul@pwsan.com: revised patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Some modules (like GPIO, DSS...) require optionals clock to be enabled
in order to complete the sofreset properly.
Add a HWMOD_CONTROL_OPT_CLKS_IN_RESET flag to force all optional clocks
to be enabled before reset. Disabled them once the reset is done.
TODO:
For the moment it is very hard to understand from the HW spec, which
optional clock is needed and which one is not. So the current approach
will enable all the optional clocks.
Paul proposed a much finer approach that will allow to tag only the needed
clock in the optional clock table. This might be doable as soon as we have
a clear understanding of these dependencies.
Reported-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
In OMAP3 a specific SYSSTATUS register was used to get the softreset status.
Starting in OMAP4, some IPs does not have SYSSTATUS register and instead
use the SYSC softreset bit to provide the status.
Other cases might exist:
- Some IPs like McBSP does have a softreset control but no reset status.
- Some IPs that represent subsystem, like the DSS, can contains
a reset status without softreset control. The status is the aggregation
of all the sub modules reset status.
- Add a new flag (SYSC_HAS_RESET_STATUS) to identify the new programming model
and replace the previous SYSS_MISSING, that was used to flag IP with
softreset control but without the SYSSTATUS register, with a specific
SYSS_HAS_RESET_STATUS flag.
- MCSPI and MMC contains both programming models, so the legacy one
will be prevented by removing the syss offset field that become useless.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Expose an hardreset API from hwmod in order to assert / deassert all the
individual reset lines that belong to an hwmod. This API is needed by
some of the more complicated processor drivers, e.g., DSP/Bridge,
Syslink, etc.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Force the softreset of every IPs during the _setup phase.
IPs that cannot support softreset or that should not
be reset must set the HWMOD_INIT_NO_RESET flag in the
hwmod struct.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Most processor IPs does have a hardreset signal controlled by the PRM.
This is different of the softreset used for local IP reset from the
SYSCONFIG register.
The granularity can be much finer than orginal HWMOD, for ex, the IVA
hwmod contains 3 reset lines, the IPU 3 as well, the DSP 2...
Since this granularity is needed by the driver, we have to ensure
than one hwmod exist for each hardreset line.
- Store reset lines as hwmod resources that a driver can query by name like
an irq or sdma line.
- Add two functions for asserting / deasserting reset lines in hwmods
processor that require manual reset control.
- Add one functions to get the current reset state.
- If an hwmod contains only one line, an automatic assertion / de-assertion
is done.
-> de-assert the hardreset line only during enable from disable transition
-> assert the hardreset line only during shutdown
Note: The hwmods with hardreset line and HWMOD_INIT_NO_RESET flag must be
kept in INITIALIZED state.
They can be properly enabled only if the hardreset line is de-asserted
before.
For information here is the list of IPs with HW reset control
on an OMAP4430 device:
RM_DSP_RSTCTRL
1,1,'RST2','RW','1','DSP - MMU, cache and slave interface reset control'
0,0,'RST1','RW','1','DSP - DSP reset control'
RM_IVA_RSTCTRL
2,2,'RST3','RW','1','IVA logic and SL2 reset control'
1,1,'RST2','RW','1','IVA Sequencer2 reset control'
0,0,'RST1','RW','1','IVA sequencer1 reset control'
RM_IPU_RSTCTRL
2,2,'RST3','RW','1','IPU MMU and CACHE interface reset control.'
1,1,'RST2','RW','1','IPU Cortex M3 CPU2 reset control.'
0,0,'RST1','RW','1','IPU Cortex M3 CPU1 reset control.'
PRM_RSTCTRL
1,1,'RST_GLOBAL_COLD_SW','RW','0','Global COLD software reset control.'
0,0,'RST_GLOBAL_WARM_SW','RW','0','Global WARM software reset control.'
RM_CPU0_CPU0_RSTCTRL
RM_CPU1_CPU1_RSTCTRL
0,0,'RST','RW','0','Cortex A9 CPU0&1 warm local reset control'
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: made the hardreset functions static; moved the register
twiddling into prm*.c functions in previous patches; changed the
function names to conform with hwmod practice]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
This patch adds hard-reset support for processor modules (e.g., DSP, IVA)
on OMAP2/3 platforms. It's based on the OMAP4 hard-reset support that Benoît
developed in the previous patch.
This patch is a collaboration between Benoît Cousson <b-cousson@ti.com>
and Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Most processor modules (e.g., DSP, IVA, IPU) on OMAPs can be reset
under the control of the PRM. This patch adds an API for this purpose
for OMAP4 devices:
int omap4_prm_is_hardreset_asserted(void __iomem *rstctrl_reg, u8 shift);
int omap4_prm_assert_hardreset(void __iomem *rstctrl_reg, u8 shift);
int omap4_prm_deassert_hardreset(void __iomem *rstctrl_reg, u8 shift);
This API is intended to be used only by the hwmod code - a subsequent
patch will add that support to hwmod.
This patch is a collaboration between Benoît Cousson <b-cousson@ti.com>
and Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Since OMAP4 is using an absolute address, the current PRM accessors
are not useable.
OMAP4 adaptation for these API are currently ongoing, so define temp
version until the proper ones are defined.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently omap_hwmod_mutex is being used to protect both the list
access/modification and concurrent access to hwmod functions. This
patch separates these two types of locking.
First, omap_hwmod_mutex is used only to protect access and
modification of omap_hwmod_list. Also cleaned up some comments
referring to this mutex that are no longer needed.
Then, for protecting concurrent access to hwmod functions, use a
per-hwmod mutex. This protects concurrent access to a single hwmod,
but would allow concurrent access to different hwmods.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[paul@pwsan.com: added structure documentation; changed mutex variable
name]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP4 platform has different register bits for Warm and Cold Resets.
Write one into appropriate bits.
Signed-off-by: Rajeev Kulkarni <rajeevk@ti.com>
Cc: Leed Aguilar <leed.aguilar@ti.com>
[b-cousson@ti.com: Change the define with the proper one from omap4 headers]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
The reset function wrongly used the state flag as a bit mask and was trying
to re-enable after a reset.
hwmod is still enabled for the PRCM point of view after a softreset
so there is no need to re-enable.
Remove the state check from omap_hwmod_reset since the _reset
function is checking that as well and in addition can generate
a warning
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
[b-cousson@ti.com: remove the wrong test, remove the re-enable]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The disable function was disabling clocks and dependencies
from both enable and idle state. Since idle function is already
disabling both, an enable -> idle -> disable sequence will
try to disable twice the clocks and thus generate a
"Trying disable clock XXX with 0 usecount" warning.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
On OMAP1, we do not have omap_device + omap_hwmod to manage the
device-specific idle, enable and shutdown. Instead, just
enable/disable device clocks automatically at the runtime PM level.
This allows drivers to not have any OMAP1 specific clock management
and allows them to simply use the runtime PM API to manage clocks.
OMAP1 compile fixes Manjunatha GK <manjugk@ti.com>
Cc: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Implement the new runtime PM framework as a thin layer on top of the
omap_device API. OMAP specific runtime PM methods are registered with
the as custom methods on the platform_bus.
In order to determine if a device is an omap_device, its parent device
is checked. All omap_devices have a new 'omap_device_parent_ device
as their parent device, so checking for this parent is used to check
for valid omap_devices. If a device is an omap_device, then the
appropriate omap_device functions are called for it. If not, only the
generic runtime PM functions are called.
Device driver's ->runtime_idle() hook is called when the runtime PM
usecount reaches zero for that device. Driver's ->runtime_suspend()
hooks are called just before the device is disabled (via
omap_device_idle()), and device driver ->runtime_resume() hooks are
called just after device has been enabled (via omap_device_enable().)
OMAP4 build support from Rajendra Nayak <rnayak@ti.com>.
OMAP2 build support from Charulatha V <charu@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Charulatha V <charu@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes omap3 hardcodings from pm-debug.c
so that enabling PM debugfs support does break compilation
for other OMAP's. This is a preparatory patch for supporting
OMAP4 pm entries through PM debugfs.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cleanup indentation around IO wakeup enable, the '\' terminator is
not required in C when wrapping an expression past end-of-line.
Whitespace change only.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The dma request line attribute was named dma channel, which leads
to confusion with the real dma channel definition.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
We need to make sure that only the first do_signal() to be handled on
the way out syscall will bother with syscall restarts; additionally, the
check on the "signal has user handler" path had been wrong - compare
with restart prevention in sigreturn()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
do_signal() should place the syscall number in gr7, not gr8 when
handling ERESTART_WOULDBLOCK.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use force_sigsegv() rather than force_sig(SIGSEGV, ...) as the former
resets the SEGV handler pointer which will kill the process, rather than
leaving it open to an infinite loop if the SEGV handler itself caused a
SEGV signal.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a) sa_handler might be maliciously set to point to kernel memory;
blindly dereferencing it in FDPIC case is a Bad Idea(tm).
b) I'm not sure you need that set_fs(USER_DS) there at all, but if you
do, you'd better do it *before* checking the frame you've decided to
use with access_ok(), lest sigaltstack() becomes a convenient
roothole.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reset restart_block.fn on executing a sigreturn such that any currently
pending system call restarts will be forced to return -EINTR.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
