- Remove a redundant exported gate control function
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also add in some more device ID's
Signed-off-by: Oleg Roitburd <oroitburd@gmail.com>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID 1b80:e39a for KWorld TV Stick II (395UR).
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID 1b80:e383 for KWorld USB DVB-T Stick Mobile (UB383-T).
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Current dvb_demux_tscheck processing doesn't allow to enable check on loaded
module. dvb_demux_tscheck can be enabled only when loading module (
dvb_dmx_init should be called to enable dvb_demux_tscheck ). This patch fix
this issue.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The version number in the CA_PMT message sent to the hardware was
alwaysed set to zero. This could cause problems if the PMT would
change during decryption of a channel since the new CA_PMT would have
the same version number as the old. The version number is now copied
from the original PMT.
Signed-off-by: Henrik Kurelid <henrik@kurelid.se>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The condition (msg[i].addr == 0xd0) is checked twice the second one
is not necessary.
This will remove the following compiler warning:
az6027.c: In function 'az6027_i2c_xfer':
az6027.c:942: warning: 'index' may be used uninitialized in this function
az6027.c:943: warning: 'value' may be used uninitialized in this function
az6027.c:944: warning: 'length' may be used uninitialized in this function
az6027.c:945: warning: 'req' may be used uninitialized in this function
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use NULL when calling a function with pointer parameter, initializing a
pointer and returning a pointer. This will remove the following sparse
warning at different locations (see "make C=1"):
* warning: Using plain integer as NULL pointer
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Address a problem found in MythTV where if we are in digital mode, switch to
analog mode, and the switch back to digital mode, the first tuning request
after switching back to digital mode gets dropped. This is because the au8522
maintains internal state, and would think the demod was already tuned to the
target frequency.
Thanks to Zaphod Beeblebrox for reporting this issue.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With applications like MythTV, switching inputs results in closing the digital
side and then immediately opening the analog side. This exposes a race
condition where the dvb_frontend kernel thread powers down the chip and closes
the i2c gate even though we're in the middle of bringing up the analog part
of the chip (since the shutdown of the dvb_frontend kernel thread occurs
asychronously).
Introduce a construct to keep track of what mode we're in, and drop requests
to power down or management the gate if we've already switched to analog mode.
Thanks to Zaphod Beeblebrox for reporting this issue.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This requires changing all users of dvb_usercopy to
omit the inode argument.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Never call dvb_frontend_detach if we failed to attach a frontend. This fixes
the following oops, which will be triggered by a missing stv090x module:
[ 8.172997] DVB: registering new adapter (TT-Budget S2-1600 PCI)
[ 8.209018] adapter has MAC addr = 00:d0:5c:cc:a7:29
[ 8.328665] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 8.328753] Intel ICH 0000:00:1f.5: setting latency timer to 64
[ 8.562047] DVB: Unable to find symbol stv090x_attach()
[ 8.562117] BUG: unable to handle kernel NULL pointer dereference at 000000ac
[ 8.562239] IP: [<e08b04a3>] dvb_frontend_detach+0x4/0x67 [dvb_core]
Ref http://bugs.debian.org/575207
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Send one DiSEqC byte to make sure that the pin is set to low level.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Reviewed-by: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
In mlx4, using char * to store mc address in private structure instead.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add ALDI/MEDION netbook E1222 to qurik reset table
Input: ALPS - fix stuck buttons on some touchpads
Input: wm831x-on - convert to use genirq
Input: ads7846 - add wakeup support
Input: appletouch - fix integer overflow issue
Input: ad7877 - increase pen up imeout
Input: ads7846 - add support for AD7843 parts
Input: bf54x-keys - fix system hang when pressing a key
Input: alps - add support for the touchpad on Toshiba Tecra A11-11L
Input: remove BKL, fix input_open_file() locking
Input: serio_raw - remove BKL
Input: mousedev - remove BKL
Input: add driver for TWL4030 vibrator device
Input: enable remote wakeup for PNP i8042 keyboard ports
Input: scancode in get/set_keycodes should be unsigned
Input: i8042 - use platfrom_create_bundle() helper
Input: wacom - merge out and in prox events
Input: gamecon - fix off by one range check
Input: wacom - replace WACOM_PKGLEN_PENABLED
The HID layer has some scan codes of the form 0xffbc0000 for logitech
devices which do not work if scancode is typed as signed int, so we need
to switch to unsigned it instead. While at it keycode being signed does
not make much sense either.
Acked-by: Márton Németh <nm127@freemail.hu>
Acked-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (23 commits)
firewire: ohci: extend initialization log message
firewire: ohci: fix IR/IT context mask mixup
firewire: ohci: add module parameter to activate quirk fixes
firewire: ohci: use an ID table for quirks detection
firewire: ohci: reorder struct fw_ohci for better cache efficiency
firewire: ohci: remove unused dualbuffer IR code
firewire: core: combine a bit of repeated code
firewire: core: change type of a data buffer
firewire: cdev: increment ABI version number
firewire: cdev: add more flexible cycle timer ioctl
firewire: core: rename an internal function
firewire: core: fix an information leak
firewire: core: increase stack size of config ROM reader
firewire: core: don't fail device creation in case of too large config ROM blocks
firewire: core: fix "giving up on config rom" with Panasonic AG-DV2500
firewire: remove incomplete Bus_Time CSR support
firewire: get_cycle_timer optimization and cleanup
firewire: ohci: enable cycle timer fix on ALi and NEC controllers
firewire: ohci: work around cycle timer bugs on VIA controllers
firewire: make PCI device id constant
...
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (362 commits)
V4L-DVB: cx88-dvb: remove extra attribution for core
V4L/DVB: v4l: soc_camera: fix bound checking of mbus_fmt[] index
V4L/DVB: Add support for SMT7020 to cx88
V4L/DVB: radio-si470x: Use UTF-8 encoding on a comment
V4L/DVB: MAINTAINERS: Telegent tlg2300 section fix
V4L/DVB: gspca_stv06xx: Add support for camera button
V4L/DVB: gspca_ov519: add support for the button on ov511 based cams
V4L/DVB: gspca_ov519: Add support for the button on ov518 based cams
V4L/DVB: gspca_ov519: add support for the button on ov519 based cams
V4L/DVB: gspca_main: Fix a compile error when CONFIG_INPUT is not set
V4L/DVB: gspca_main: some input error handling fixes
V4L/DVB: gspca_main: Allow use of input device creation code for non int. inputs
V4L/DVB: gspca_pac7302: much improved exposure control
V4L/DVB: gspca_sonixb: Make sonixb driver handle pas106 and pas202 cameras
V4L/DVB: gspca_sonixb: pas106: fixup bright ctrl and add gain and exposure ctrls
V4L/DVB: Documentation: gspca.txt: update known mr97310a cams
V4L/DVB: gspca_mr97310a: add support for the Sakar 1638x CyberPix
V4L/DVB: gscpa_sonixb: limit ov7630 max framerate at 640x480
V4L/DVB: gspca_sonixb: pas202: fixup brightness ctrl and add gain and exposure ctrls
V4L/DVB: gscpa_sonixb: Differentiate between sensors with a coarse and fine expo ctrl
...
ULE (Unidirectional Lightweight Encapsulation RFC 4326) decapsulation
has a bug that causes endless loop when Payload Pointer of MPEG2-TS
frame is 182 or 183. Anyone who sends malicious MPEG2-TS frame will
cause the receiver of ULE SNDU to go into endless loop.
This patch was generated and tested against linux-2.6.32.9 and should
apply cleanly to linux-2.6.33 as well because there was only one typo
fix to dvb_net.c since v2.6.32.
This bug was brought to you by modern day Santa Claus who decided to
shower the satellite dish at Keio University with heavy snow causing
huge burst of errors. We, receiver end, received Santa Claus's gift in
the form of kernel bug.
Care has been taken not to introduce more bug by fixing this bug, but
please scrutinize the code for I always produces buggy code.
Signed-off-by: Ang Way Chuang <wcang79@gmail.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The parenthesis was misplaced, tmp is set to 0 or break occurs,
while debugging opera1_usb_i2c_msgxfer() retval was not shown.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
CC: Marco Gittler <g.marco@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix sparse warnings in media/dvb/frontends:
drivers/media/dvb/frontends/dibx000_common.c:177:13: warning: non-ANSI function declaration of function 'systime'
drivers/media/dvb/frontends/tda665x.c:136:55: warning: right shift by bigger than source value
[mchehab@redhat.com: removed the change at dib0090 since it got fixed by a previous patch]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Userspace is allowed to coalesce events between SYNCs. And since the code
emits UP right after DOWN for the same key, it may be missed
(up+down=nothing). Add an extra sync in between UP and DOWN events to disable
the coalesce.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/dvb-usb/az6027.c:390: warning: excess elements in struct initializer
drivers/media/dvb/dvb-usb/az6027.c:390: warning: (near initialization for ‘az6027_rc_keys[0]’)
drivers/media/dvb/dvb-usb/az6027.c:391: warning: excess elements in struct initializer
drivers/media/dvb/dvb-usb/az6027.c:391: warning: (near initialization for ‘az6027_rc_keys[1]’)
drivers/media/dvb/dvb-usb/az6027.c:759: warning: ‘az6027_read_mac_addr’ defined but not used
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/dvb-usb/az6027.c:759: warning: ‘az6027_read_mac_addr’ defined but not used
While there's some code that uses it, it is currently commented. So, comment also
the function itself.
CC: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/dvb-usb/az6027.c:390: warning: excess elements in struct initializer
drivers/media/dvb/dvb-usb/az6027.c:390: warning: (near initialization for ‘az6027_rc_keys[0]’)
drivers/media/dvb/dvb-usb/az6027.c:391: warning: excess elements in struct initializer
drivers/media/dvb/dvb-usb/az6027.c:391: warning: (near initialization for ‘az6027_rc_keys[1]’)
CC: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no driver for new NXP TDA18218 tuner which is used by few recent
af9015 designs. af9015 uses number 179 as ID for that tuner. Inform this
tuner is not supported when device using that tuner is meet.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID 0413:6a04 for Leadtek WinFast DTV2000DS.
Thanks to Gavin Ramm <gavin_ramm@hotmail.com> for reporting this.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID 1b80:e402 for DigitalNow TinyTwin version 2.
Thanks to Trevor Phillips <trevor.phillips@gmail.com> for reporting this.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Switch second and third memset parameter to stamp the length buffer bytes
by 0xff's, not 255 bytes by low 8 bits of Length.
Cc: linux-media@vger.kernel.org, linux-kernel@vger.kernel.org, jirislaby@gmail.com, Matthias Benesch <twoof7@freenet.de>, Ralph Metzler <rjkm@metzlerbros.de>, Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Matthias Benesch <twoof7@freenet.de>
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Cc: Oliver Endriss <o.endriss@gmx.de>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In each case, the NULL test has been performed already.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression *x;
expression e;
identifier l;
@@
if (x == NULL || ...) {
... when forall
return ...; }
... when != goto l;
when != x = e
when != &x
*x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove check "state->dst_type == DST_DTYPE_IS_CABLE" in function
dst_get_tuna (around line 1352) to select the correct checksum
computation
Fill in the .caps field in struct dst_dvbc_ops (around line 1824) with
all the supported QAM modulation methods to match the capabilities of
the card as implemented in function dst_set_modulation (around line
502). Note that beginning with linux kernel version 2.6.32 the
modulation method is checked (by function
dvb_frontend_check_parameters in file
drivers/media/dvb/dvb-core/dvb_frontend.c) and thus tuning fails if
you use a modulation method that is not present in the .caps field.
This patch has been tested on a Twinhan VP2031A DVB-C card with the
2.6.32.2 kernel.
Signed-off-by: Klaas de Waal <klaas.de.waal@gmail.com>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
if the AGC2 > 1400 then no signal on this frequency for STV0900 Cut 3.0. For
Cut 2.0 this value is 700.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After merging the scsi-post-merge tree, today's linux-next build (powerpc
allyesconfig) failed like this:
drivers/media/dvb/ngene/ngene-core.c: In function 'ngene_release_buffers':
drivers/media/dvb/ngene/ngene-core.c:1443: error: implicit declaration of function 'vfree'
drivers/media/dvb/ngene/ngene-core.c: In function 'ngene_get_buffers':
drivers/media/dvb/ngene/ngene-core.c:1454: error: implicit declaration of function 'vmalloc'
drivers/media/dvb/ngene/ngene-core.c:1454: warning: assignment makes pointer from integer without a cast
drivers/media/dvb/ngene/ngene-core.c:1461: warning: assignment makes pointer from integer without a cast
drivers/media/dvb/ngene/ngene-core.c:1467: warning: assignment makes pointer from integer without a cast
drivers/media/dvb/ngene/ngene-core.c: In function 'ngene_probe':
drivers/media/dvb/ngene/ngene-core.c:1836: warning: assignment makes pointer from integer without a cast
Caused by commit b54c755d6263efe376f3dfc8c72c8e7b4fb4f4c1 ("V4L/DVB: ngene: Initial check-in").
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use I2C_CLASS_TV_DIGITAL, not I2C_ADAP_CLASS_TV_DIGITAL.
Remove initialisation of bus_lock mutex.
Thanks to Mauro for pointing out.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Thanks-to: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cards 18c3:abc3/18c3:abc4 should be displayed as 'Linux4Media cineS2'.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Request might already have been processed when the interrupt arrives.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implement workaround for comamnd timeout.
Use FW15 and avoid switching DMA on and off.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set ADC1 and ADC2 range of the stv0900 to 1Vpp.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adapt to current stv090x + stv6110 drivers.
[mchehab@redhat.com: removed compilation hack added by me on a prev patch]
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trivial I2C related fixes/cleanups
- Remove Unused I2C ID
- point the I2C device to the physical device
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If parameter "one_adapter" is set, only one adapter per device will be attached.
Otherwise an adapter for every frontend will be attached.
Signed-off-by: Matthias Benesch <twoof7@freenet.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove kernel version check for dvb_[un]register_adapter.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changed severity of some diagnostic messages.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add Micronas nGene PCIe bridge driver.
The source code was provided by Micronas / Ralph Metzler,
and has been reformatted to comply with Linux Codingstyle.
Signed-off-by: Matthias Benesch <twoof7@freenet.de>
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
So as a final patch, add support for hash and one hash entry
for MSI digi vox mini II:
iManufacturer 1 Afatech
iProduct 2 DVB-T 2
iSerial 3 010101010600001
It is now handled with proper IR and key map tables.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add af9015_setup structure to hold (right now only remote) setup
of distinct receivers.
Add af9015_setup_match for matching ids against tables.
This is for easier matching different kind of ids against tables
to obtain setups. Currently module parameters and usb vendor ids
are switched into and matched against tables. Hashes will follow.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is just a code shuffle without functional changes. For easier
review of later changes, i.e. preparation.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This will be useful for matching of IR tables later.
We read the eeprom anyway for dumping. Switch the dumping to
print_hex_dump_bytes and compute hash above that by
hash = 0;
for (u32 VAL) in (eeprom):
hash *= GOLDEN_RATIO_PRIME_32
hash += VAL; // while preserving endinaness
The computation is moved earlier to the flow, namely from
af9015_af9013_frontend_attach to af9015_read_config, so that
we can access the sum in af9015_read_config already.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mad guess.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Manu Abraham <manu@linuxtv.org>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/frontends/stv090x.c: In function 'stv090x_blind_search':
drivers/media/dvb/frontends/stv090x.c:1967: warning: 'coarse_fail' may be used uninitialized in this function
Cc: Manu Abraham <manu@linuxtv.org>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Manu Abraham <manu@linuxtv.org>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If in a cold state and the download succeeded ret is zero, but we
should return -ENOMEM.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the file local parameters static.
This will remove the following sparse warnings (see "make C=1"):
* warning: symbol 'ir_pos' was not declared. Should it be static?
* warning: symbol 'ir_word' was not declared. Should it be static?
* warning: symbol 'ir_toggle' was not declared. Should it be static?
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds support to Pinnacle PCTV310e hybrid tuner card, for DVB-T and
remote control, still no analog video.
[mchehab@redhat.com: fix CodingStyle issues]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
state->internal allocation may fail as well as the allocation of
stv0900_first_inode or new_node->next_inode in append_internal().
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The init and exit functions are needlessly complex. Remove the bloat:
* Drop irrelevant/outdated comments.
* Remove useless bt878_pci_driver_registered global variable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before each FCP transdaction, the entire 512 bytes of the FCP frame were
cleared, then values filled in.
Clear only the bytes between filled-in bytes and end of the
- request frame, or
- response frame if data from a larger response will be needed, or
- whole frame if data from a variable length response will be taken.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
FCP transactions as well as CMP transactions were serialized with
mutex_lock_interruptible. It is extremely unlikly though that a signal
will arrive while a concurrent process holds the mutex. And even if one
does, the duration of a transaction is reasonably short (1.2 seconds if
all retries time out, usually much shorter).
Hence simplify the code to plain mutex_lock.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a portability fix and reduces stack usage.
The DMA mapping API cannot map on-stack addresses, as explained in
Documentation/DMA-mapping.txt. Convert the two cases of on-stack packet
payload buffers in firedtv (payload of write requests in avc_write and
of lock requests in cmp_lock) to slab-allocated memory.
We use the 512 bytes sized FCP frame buffer in struct firedtv for this
purpose. Previously it held only incoming FCP responses, now it holds
pending FCP requests and is then overwriten by an FCP response from the
tuner subunit. Ditto for CMP lock requests and responses. Accesses to
the payload buffer are serialized by fdtv->avc_mutex.
As a welcome side effect, stack usage of the AV/C transaction functions
is reduced by 512 bytes.
Alas, avc_register_remote_control() is a special case: It previously
did not wait for a response. To fit better in with the other FCP
transactions, let it wait for an interim response.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
'extern' is not needed at function definition.
This will remove the following sparse warning (see "make C=1"):
* function 'dib0090_dcc_freq' with external linkage has definition
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some functions are only used locally so mark them static.
This will remove the following sparse warnings (see "make C=1"):
* symbol 'extract_mask_pos' was not declared. Should it be static?
* symbol 'stv0900_initialize' was not declared. Should it be static?
* symbol 'stv0900_get_mclk_freq' was not declared. Should it be static?
* symbol 'stv0900_set_mclk' was not declared. Should it be static?
* symbol 'stv0900_get_err_count' was not declared. Should it be static?
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The functions stv0900_sw_algo() and stv0900_set_dvbs1_track_car_loop() are only used
locally so mark them static.
This will remove the following sparse warnings (see "make C=1"):
* symbol 'stv0900_sw_algo' was not declared. Should it be static?
* symbol 'stv0900_set_dvbs1_track_car_loop' was not declared. Should it be static?
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is for better readability and smaller size of code lines.
Also it is for future improvements like GPIO handling.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is for better readability and smaller size of code.
Also it is similar to other drivers.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The PCI card contains dm1105 PCI bridge and ds3000 demod.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
22-kHz tone can be driven in two ways:
1. LNBH24 can produce 22kHz continuous tone when TEN=1 ( 22 KHz tone output is
always activated ).
2. LNBH24 can reproduce 22kHz tone timings from DSQIN or EXTM pin's when TEN=0.
From LNBH24 datasheet:
"In order to improve design flexibility an external tone input pin is
available (EXTM). The EXTM is a Logic input pin which activates the 22 kHz
tone output, on the VoTX pin, by using the LNBH24 integrated tone generator
(similar to the DSQIN pin function). In fact, the output tone waveform
characteristics will always be internally controlled by the LNBH24 tone
generator and the EXTM signal will be used as a timing control for DiSEqC tone
data encoding on the VoTX output."
In NetUP Dual DVB-S2-CI card 22kHz tone timings on EXTM pin produced by
STV0900 demod:
.set_tone = stv0900_set_tone
redefine to "set_tone = lnbp21_set_tone" is not correct for "NetUP Dual
DVB-S2-CI card".
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Exit stv090x_algo() if the tuner did not lock. This might happen due to
missing signal or invalid/incomplete tuning parameters.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The I2C gate must also be disabled, if a tuner command failed.
Otherwise the tuner mutex would be locked forever.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When mclk is not 0 then it will never be set to the correct value and
the Demodulator will not work.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This gives the STV090x and improved clock signal (rectangle instead of sine).
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using clk_div member of stv6110x_config structure the tuner's clock
output divider can be configured. It is set in stv6110x_attach.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is needed when clock input is driven from tuner and an output
divider different from 1 is used.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before there was used a static register map that could lead to issues
when there are are multiple adapters with the STV6110(A).
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function stv6110x_write_regs is used to write several registers at once.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This could be useful for p.e. Common Interface applications where data rate is limited.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With this change it is possible to have the same I2C address for both tuners.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the STV0900 features two demodulation paths in one chip there is
some information used by both instances of the driver when used in
dual mode. This information is now shared in an internal structure
referenced by I2C adapter and address.
Do initialisation of the demodulator only once when used in dual mode.
Moved global mutex demod_lock to internal structure.
Moved dev_ver and mclk to internal structure.
Removed unused tuner_refclk from stv090x_state.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In automatic S/S2 detection mode, locking of a DVB-S transponder could
fail when coming from a DVB-S2 transponder. This change fixes the issue
by first disabling DVB-S and DVB-S2 mode before enabling it again.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
22-kHz tone can be driven in two ways:
1. LNBH24 can produce 22kHz continuous tone when TEN=1 ( 22 KHz tone output is
always activated ).
2. LNBH24 can reproduce 22kHz tone timings from DSQIN or EXTM pin's when TEN=0.
From LNBH24 datasheet:
"In order to improve design flexibility an external tone input pin is
available (EXTM). The EXTM is a Logic input pin which activates the 22 kHz
tone output, on the VoTX pin, by using the LNBH24 integrated tone generator
(similar to the DSQIN pin function). In fact, the output tone waveform
characteristics will always be internally controlled by the LNBH24 tone
generator and the EXTM signal will be used as a timing control for DiSEqC tone
data encoding on the VoTX output."
In NetUP Dual DVB-S2-CI card 22kHz tone timings on EXTM pin produced by
STV0900 demod:
.set_tone = stv0900_set_tone
redefine to "set_tone = lnbp21_set_tone" is not correct for "NetUP Dual
DVB-S2-CI card".
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trivial patch which adds the __init/__exit macros to the module_init/
module_exit functions of
drivers/media/dvb/bt8xx/bt878.c
Please have a look at the small patch and either pull it through
your tree, or please ack' it so Jiri can pull it through the trivial
tree.
Patch against linux-next-tree, 22. Dez 08:38:18 CET 2009
but also present in linus tree.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
And a little code refactoring/neatening around the removals
Reduces object size a little bit:
new:
$ size drivers/media/dvb/frontends/si21xx.o
text data bss dec hex filename
8984 56 1816 10856 2a68 drivers/media/dvb/frontends/si21xx.o
old:
$ size drivers/media/dvb/frontends/si21xx.o
text data bss dec hex filename
9084 56 1792 10932 2ab4 drivers/media/dvb/frontends/si21xx.o
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stanse found an unreachable statement in zl10039_attach. There is
a `break' followed by `goto error'. Remove that break, so that it
can handle the error.
Cc: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stanse found a memory leak in smscore_gpio_configure. buffer is not
freed/assigned on all paths. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I was initially concerned about the weird array index (the 2 bumps
into the next row of the array). Matthias Schwarzott look at the
datasheet and it turns out it should be zl10036_init_tab[1][0] |= 0x01;
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If there is ever going to be a FireDTV or FloppyDTV firmware which does
not provide a minimal ASCII textual descriptor for Model_Id --- or if
the descriptor is provided indirectly in a descriptor directory ---
the ieee1394 variant of the device probe of firedtv would dereference a
NULL pointer. The firewire variant of firedtv's device probe is not
affected.
The fix makes sure that such an unexpected firmware is safely recognized
by fdtv_alloc as an unknown firmware.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the NULL test is necessary, then the dereference should be moved below
the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When firmware 1.20 was introduced, the dib0700 switched from a polling model
using a USB control message, to the messages being delivered on a USB bulk
pipe. The code I originally added would do a blocking read on the pipe with a
50ms timeout. Because the dvb-usb-remote code makes use of the global
workqueue, this resulted in the global workqueue being blocked 50% of the
time. Also, the synchronous urb_bulk_msg() call would burn excess CPU time
(reflected as an abnormal increase in the system's load average when devices
were connected).
Rework the logic so that we now setup an asynchronous callback on the bulk
pipe, so that we now only handle RC data when it arrives on the pipe. Note
that we provide a stub function for the RC polling callback so that we can
continue to leverage the shared code in dvb-usb-rc for the setting up of the
input device.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, if RF is locked but demod is not locked, it will report:
>>> tuning status == 0x03
This happens, for example, if the device is on DVB-T, and the video
standard is ISDB-T.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After taking a look at the driver's history and doing some tests with
DVB and ISDB-T, it was noticed that the stats were incomplete, for
ISDB-T, and weren't working for DVB.
Fixed the code and added a debug code to print the complete stats at
dmesg. This debug is useful to improve the stats of this driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Based on a patch originally written by Michael Krufky <mkrufky@linuxtv.org>
for a preliminar S2API spec.
The patch were ported to the S2API and had the ISDB-T API additions to
honor the auto mode, while keep allowing manual tuning.
Tested with both the original dvb-apps and the new dvb-apps-isdbt scan,
that uses a different channel.conf and uses S2API with ISDB-T extensions.
Thanks-to: Michael Krufky <mkrufky@linuxtv.org> for his first version
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Siano series of patches seemed to cause a regression on reporting DTV
statistics. Due to that, signal indication weren't received, preventing
applications like scan to work.
Tested with ISDB-T signals and got the same scan result as with a
dib0700/dib8000 device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Activate ISDB-T mode using module option default_mode=6.
hack: use 4 lower bits in frequency for segment number
[mchehab@redhat.com: fix merge conflicts and CodingStyle]
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Improves ATBM8830 reception by using per card AGC configuration rather
than register default.
Signed-off-by: David T. L. Wong <davidtlwong@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card based on stv0903 demod, stb6100 tuner.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When preparing the linux-next patches, I got those errors:
include/media/ir-core.h:29: warning: left shift count >= width of type
In file included from include/media/ir-common.h:29,
from drivers/media/video/ir-kbd-i2c.c:50:
drivers/media/video/ir-kbd-i2c.c: In function ‘ir_probe’:
drivers/media/video/ir-kbd-i2c.c:324: warning: left shift count >= width of type
Unfortunately, enum is 32 bits on i386. As we define IR_TYPE_OTHER as 1<<63,
it won't work on non 64 bits arch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds an structure to ir_input_register to contain IR device characteristics,
like supported protocols and a callback to handle protocol event changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cxusb uses the atbm8830 and lgs8gxx (not lgs8gl5) frontends and the
max2165 tuner, so it needs to select them.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I'm trying to fix it on the GCC side (PR43007), but the module is
quite stupid in using ULL constants to operate on u32 values:
static int apply_frontend_param (struct dvb_frontend* fe, struct
dvb_frontend_parameters *param)
{
...
static const u32 ppm = 8000;
u32 spi_bias;
...
spi_bias *= 1000ULL;
spi_bias /= 1000ULL + ppm/1000;
which causes current GCC 4.5 to emit calls to __udivdi3 for i?86 again.
This patch fixes this issue.
Signed-off-by: Richard Guenther <rguenther@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A DVB demultiplexer device can be used to set up either a PES filter or
a section filter. In the former case, the ts field of the feed union of
struct dmxdev_filter is used, in the latter case the sec field of the
same union is used.
The ts field is a struct list_head, and is currently initialized in the
open() method of the demux device. When for a given demuxer a section
filter is set up, the sec field is played with, thus if a PES filter
needs to be set up after that the ts field will be corrupted, causing a
kernel oops.
This fix moves the list head initialization to
dvb_dmxdev_pes_filter_set(), so that the ts field is properly
initialized every time a PES filter is set up.
Signed-off-by: Francesco Lavra <francescolavra@interfree.it>
Cc: stable <stable@kernel.org>
Reviewed-by: Andy Walls <awalls@radix.net>
Tested-by: hermann pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As dvb_dmx_swfilter_packet() is protected by a spinlock, it shouldn't sleep.
However, vmalloc() may call sleep. So, move the initialization of
dvb_demux::cnt_storage field to a better place.
Reviewed-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dvb_dmx_init tries to allocate virtual memory for 2 pointers: filter and feed.
If the second vmalloc fails, filter is freed, but the pointer keeps pointing
to the old place. Later, when dvb_dmx_release() is called, it will try to
free an already freed memory, causing an OOPS.
Reviewed-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trivial patch which adds the __init/__exit macros to the module_init/
module_exit functions of
drivers/media/dvb/bt8xx/bt878.c
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'mantis' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (117 commits)
V4L/DVB (13851): Fix Input dependency for Mantis
V4L/DVB(13824a): mantis: Fix __devexit bad annotations
V4L/DVB (13808b): mantis: replace DMA_nnBIT_MASK to DMA_BIT_MASK(32)
V4L/DVB (13808): [Mantis/Hopper] Build update for Mantis/Hopper based cards
V4L/DVB(13808a): mantis: convert it to the new ir-core register/unregister functions
V4L/DVB (13812): [Mantis/Hopper] Update Copyright header
V4L/DVB (13811): [MB86A16] Update Copyright header
V4L/DVB (13810): [MB86A16] Use DVB_* macros
V4L/DVB (13809): Fix Checkpatch violations
V4L/DVB (13807): Fix: Free device in the device registration failure case
V4L/DVB (13806): Register and Initialize Remote control
V4L/DVB (13805): Fix: Unregister the frontend before detaching
V4L/DVB (13804): Remove unused I2C Adapter ID
V4L/DVB (13803): Remove unused dependency on CU1216
V4L/DVB (13802): [Mantis/Hopper] Fix all build related warnings
V4L/DVB (13801): [MB86A16] Use the search callback
V4L/DVB (13800): [Mantis] I2C optimization. Required delay is much lesser than 1mS.
V4L/DVB (13799): [Mantis] Unregister frontend
V4L/DVB (13798): [Mantis] Enable power for all cards, use byte mode only on relevant devices
V4L/DVB (13797): [Mantis/Hopper/TDA665x] Large overhaul,
...
WARNING: drivers/media/dvb/mantis/built-in.o(.devinit.text+0x13d7): Section mismatch in reference from the function mantis_pci_probe() to the function .devexit.text:mantis_i2c_exit()
The function __devinit mantis_pci_probe() references
a function __devexit mantis_i2c_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_i2c_exit() so it may be used outside an exit section.
WARNING: drivers/media/dvb/mantis/built-in.o(.devinit.text+0x1433): Section mismatch in reference from the function mantis_pci_probe() to the function .devexit.text:mantis_pci_exit()
The function __devinit mantis_pci_probe() references
a function __devexit mantis_pci_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_pci_exit() so it may be used outside an exit section.
WARNING: drivers/media/dvb/mantis/built-in.o(.devinit.text+0x185e): Section mismatch in reference from the function hopper_pci_probe() to the function
.devexit.text:mantis_i2c_exit()
The function __devinit hopper_pci_probe() references
a function __devexit mantis_i2c_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_i2c_exit() so it may be used outside an exit section.
WARNING: drivers/media/dvb/mantis/built-in.o(.devinit.text+0x18ba): Section mismatch in reference from the function hopper_pci_probe() to the function .devexit.text:mantis_pci_exit()
The function __devinit hopper_pci_probe() references
a function __devexit mantis_pci_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_pci_exit() so it may be used outside an exit section.
WARNING: drivers/media/dvb/built-in.o(.devinit.text+0x68b8): Section mismatch in reference from the function mantis_pci_probe() to the function .devexit.text:mantis_i2c_exit()
The function __devinit mantis_pci_probe() references
a function __devexit mantis_i2c_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_i2c_exit() so it may be used outside an exit section.
WARNING: drivers/media/dvb/built-in.o(.devinit.text+0x6914): Section mismatch in reference from the function mantis_pci_probe() to the function .devexit.text:mantis_pci_exit()
The function __devinit mantis_pci_probe() references
a function __devexit mantis_pci_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_pci_exit() so it may be used outside an exit section.
WARNING: drivers/media/dvb/built-in.o(.devinit.text+0x6d3f): Section mismatch in reference from the function hopper_pci_probe() to the function .devexit.text:mantis_i2c_exit()
The function __devinit hopper_pci_probe() references
a function __devexit mantis_i2c_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_i2c_exit() so it may be used outside an exit section.
WARNING: drivers/media/dvb/built-in.o(.devinit.text+0x6d9b): Section mismatch in reference from the function hopper_pci_probe() to the function .devexit.text:mantis_pci_exit()
The function __devinit hopper_pci_probe() references
a function __devexit mantis_pci_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_pci_exit() so it may be used outside an exit section.
WARNING: drivers/media/built-in.o(.devinit.text+0x14634): Section mismatch in reference from the function mantis_pci_probe() to the function .devexit.text:mantis_i2c_exit()
The function __devinit mantis_pci_probe() references
a function __devexit mantis_i2c_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_i2c_exit() so it may be used outside an exit section.
WARNING: drivers/media/built-in.o(.devinit.text+0x14690): Section mismatch in reference from the function mantis_pci_probe() to the function .devexit.text:mantis_pci_exit()
The function __devinit mantis_pci_probe() references
a function __devexit mantis_pci_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_pci_exit() so it may be used outside an exit section.
WARNING: drivers/media/built-in.o(.devinit.text+0x14abb): Section mismatch in reference from the function hopper_pci_probe() to the function .devexit.text:mantis_i2c_exit()
The function __devinit hopper_pci_probe() references
a function __devexit mantis_i2c_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_i2c_exit() so it may be used outside an exit section.
WARNING: drivers/media/built-in.o(.devinit.text+0x14b17): Section mismatch in reference from the function hopper_pci_probe() to the function .devexit.text:mantis_pci_exit()
The function __devinit hopper_pci_probe() references
a function __devexit mantis_pci_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_pci_exit() so it may be used outside an exit section.
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/mantis/mantis_pci.c: In function ‘mantis_pci_init’:
drivers/media/dvb/mantis/mantis_pci.c:76: warning: ‘DMA_nnBIT_MASK’ is deprecated
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Matthias Wachter <mathias@waechter.wiz.at>
for pointing it out.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Initial go at VP-3028, VP-3030 devices.
* I2C communication improvements,
* Add TDA665x support
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not rely on the PCI ID alone
Signed-off-by: Niklas Edmundsson <nikke@acc.umu.se>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Marko Viitamaki <mau2@suomi24.fi>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
do not use the event manager to handle the fast events
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Ershov and Igor for pointing it out.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dnumgis got hit with this bug, using a temporary workaround
for the time being rather than digging deep at this point.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
(Need to sanitize this cleanly for different Slaves)
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Magnus Horlin <magnus@alefors.se>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to hotwings <user.vdr@gmail.com> for pointing out the bug
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
