For some reason, some early WD drives spin up and down drives
erratically when the link is put into slumber mode which can reduce
the life expectancy of the device significantly. Unfortunately, we
don't have full list of devices and given the nature of the issue it'd
be better to err on the side of false positives than the other way
around. Let's disable LPM on all WD devices which match one of the
known problematic model prefixes and are SATA-I.
As horkage list doesn't support matching SATA capabilities, this is
implemented as two horkages - WD_BROKEN_LPM and NOLPM. The former is
set for the known prefixes and sets the latter if the matched device
is SATA-I.
Note that this isn't optimal as this disables all LPM operations and
partial link power state reportedly works fine on these; however, the
way LPM is implemented in libata makes it difficult to precisely map
libata LPM setting to specific link power state. Well, these devices
are already fairly outdated. Let's just disable whole LPM for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Nikos Barkas <levelwol@gmail.com>
Reported-and-tested-by: Ioannis Barkas <risc4all@yahoo.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=57211
Cc: stable@vger.kernel.org
Certain drives cannot handle queued TRIM commands properly, even
though support is indicated in the IDENTIFY DEVICE buffer. This patch
allows for disabling the commands for the affected drives and apply it
to the Micron/Crucial M500 SSDs which exhibit incorrect protocol
behavior when issued queued TRIM commands, which could lead to silent
data corruption.
tj: Merged two unnecessarily split patches and made minor edits
including shortening horkage name.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/g/1387246554-7311-1-git-send-email-marc.ceeeee@gmail.com
Cc: stable@vger.kernel.org # 3.12+
We've received multiple reports in Fedora via (BZ 907193)
that the Seagate Momentus SpinPoint M8 errors out when enabling AA:
[ 2.555905] ata2.00: failed to enable AA (error_mask=0x1)
[ 2.568482] ata2.00: failed to enable AA (error_mask=0x1)
Add the ATA_HORKAGE_BROKEN_FPDMA_AA for this specific harddisk.
Reported-by: Nicholas <arealityfarbetween@googlemail.com>
Signed-off-by: Michele Baldessari <michele@acksyn.org>
Tested-by: Nicholas <arealityfarbetween@googlemail.com>
Acked-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
After commit bcdde7e221 (sysfs: make __sysfs_remove_dir() recursive)
Mika Westerberg sees traces analogous to the one below in Thunderbolt
hot-remove testing:
WARNING: CPU: 0 PID: 4 at fs/sysfs/group.c:214 sysfs_remove_group+0xc6/0xd0()
sysfs group ffffffff81c6f1e0 not found for kobject 'host7'
Modules linked in:
CPU: 0 PID: 4 Comm: kworker/0:0 Not tainted 3.12.0+ #13
Hardware name: /D33217CK, BIOS GKPPT10H.86A.0042.2013.0422.1439 04/22/2013
Workqueue: kacpi_hotplug acpi_hotplug_work_fn
0000000000000009 ffff8801002459b0 ffffffff817daab1 ffff8801002459f8
ffff8801002459e8 ffffffff810436b8 0000000000000000 ffffffff81c6f1e0
ffff88006d440358 ffff88006d440188 ffff88006e8b4c28 ffff880100245a48
Call Trace:
[<ffffffff817daab1>] dump_stack+0x45/0x56
[<ffffffff810436b8>] warn_slowpath_common+0x78/0xa0
[<ffffffff81043727>] warn_slowpath_fmt+0x47/0x50
[<ffffffff811ad319>] ? sysfs_get_dirent_ns+0x49/0x70
[<ffffffff811ae526>] sysfs_remove_group+0xc6/0xd0
[<ffffffff81432f7e>] dpm_sysfs_remove+0x3e/0x50
[<ffffffff8142a0d0>] device_del+0x40/0x1b0
[<ffffffff8142a24d>] device_unregister+0xd/0x20
[<ffffffff8144131a>] scsi_remove_host+0xba/0x110
[<ffffffff8145f526>] ata_host_detach+0xc6/0x100
[<ffffffff8145f578>] ata_pci_remove_one+0x18/0x20
[<ffffffff812e8f48>] pci_device_remove+0x28/0x60
[<ffffffff8142d854>] __device_release_driver+0x64/0xd0
[<ffffffff8142d8de>] device_release_driver+0x1e/0x30
[<ffffffff8142d257>] bus_remove_device+0xf7/0x140
[<ffffffff8142a1b1>] device_del+0x121/0x1b0
[<ffffffff812e43d4>] pci_stop_bus_device+0x94/0xa0
[<ffffffff812e437b>] pci_stop_bus_device+0x3b/0xa0
[<ffffffff812e437b>] pci_stop_bus_device+0x3b/0xa0
[<ffffffff812e44dd>] pci_stop_and_remove_bus_device+0xd/0x20
[<ffffffff812fc743>] trim_stale_devices+0x73/0xe0
[<ffffffff812fc78b>] trim_stale_devices+0xbb/0xe0
[<ffffffff812fc78b>] trim_stale_devices+0xbb/0xe0
[<ffffffff812fcb6e>] acpiphp_check_bridge+0x7e/0xd0
[<ffffffff812fd90d>] hotplug_event+0xcd/0x160
[<ffffffff812fd9c5>] hotplug_event_work+0x25/0x60
[<ffffffff81316749>] acpi_hotplug_work_fn+0x17/0x22
[<ffffffff8105cf3a>] process_one_work+0x17a/0x430
[<ffffffff8105db29>] worker_thread+0x119/0x390
[<ffffffff8105da10>] ? manage_workers.isra.25+0x2a0/0x2a0
[<ffffffff81063a5d>] kthread+0xcd/0xf0
[<ffffffff81063990>] ? kthread_create_on_node+0x180/0x180
[<ffffffff817eb33c>] ret_from_fork+0x7c/0xb0
[<ffffffff81063990>] ? kthread_create_on_node+0x180/0x180
The source of this problem is that SCSI hosts are removed from
ATA ports after calling ata_tport_delete() which removes the
port's sysfs directory, among other things. Now, after commit
bcdde7e221, the sysfs directory is removed along with all of
its subdirectories that include the SCSI host's sysfs directory
and its subdirectories at this point. Consequently, when
device_del() is finally called for any child device of the SCSI
host and tries to remove its "power" group (which is already
gone then), it triggers the above warning.
To make the warnings go away, change the removal ordering in
ata_port_detach() so that the SCSI host is removed from the
port before ata_tport_delete() is called.
References: https://bugzilla.kernel.org/show_bug.cgi?id=65281
Reported-and-tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The endianness attribute on the 'aux' local variable is wrong, and can
lead to wrong endianness on big-endian machines,
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add support for the following ATA opcodes, which are present
in SATA 3.1 and T13 ATA ACS-3:
SEND FPDMA QUEUED
RECEIVE FPDMA QUEUED
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
SATA 3.1 added an "auxiliary" field to the host-to-device FIS.
Populate the host-to-device FIS with the new field via the
taskfile struct.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Binding ACPI handle to SCSI device has several drawbacks, namely:
1 During ATA device initialization time, ACPI handle will be needed
while SCSI devices are not created yet. So each time ACPI handle is
needed, instead of retrieving the handle by ACPI_HANDLE macro,
a namespace scan is performed to find the handle for the corresponding
ATA device. This is inefficient, and also expose a restriction on
calling path not holding any lock.
2 The binding to SCSI device tree makes code complex, while at the same
time doesn't bring us any benefit. All ACPI handlings are still done
in ATA module, not in SCSI.
Rework the ATA ACPI binding code to bind ACPI handle to ATA transport
devices(ATA port and ATA device). The binding needs to be done only once,
since the ATA transport devices do not go away with hotplug. And due to
this, the flush_work call in hotplug handler for ATA bay is no longer
needed.
Tested on an Intel test platform for binding and runtime power off for
ODD(ZPODD) and hard disk; on an ASUS S400C for binding and normal boot
and S3, where its SATA port node has _SDD and _GTF control methods when
configured as an AHCI controller and its PATA device node has _GTF
control method when configured as an IDE controller. SATA PMP binding
and ATA hotplug is not tested.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Dirk Griesbach <spamthis@freenet.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
"Overview of changes:
- The rest of maintainer email address updates.
- Some core updates - more robust default behavior for port
multipliers, better error reporting for SG_IO commands, and a way
to better work around now ancient and probably pretty rare PATA ->
SATA bridges with ATAPI devices.
- sata_rcar stabilization.
- Some hardware PCI ID additions and one-off low level driver
updates."
* 'for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
AHCI: use ATA_BUSY
libata-zpodd: must use ata_tf_init()
ahci: AHCI-mode SATA patch for Intel Coleto Creek DeviceIDs
ata_piix: IDE-mode SATA patch for Intel Coleto Creek DeviceIDs
libata: cleanup SAT error translation
ahci: sata: add support for exynos5440 sata
libata: skip SRST for all SIMG [34]7x port-multipliers
ahci: remove pmp link online check in FBS EH
sata highbank: add bit-banged SGPIO driver support
ahci: make ahci_transmit_led_message into a function pointer
sata_rcar: fix compilation warning in sata_rcar_thaw()
sata_highbank: increase retry count but shorten duration for Calxeda controller
ata: use pci_get_drvdata()
ipr: qc_fill_rtf() method should not store alternate status register
sata_rcar: add 'base' local variable to some functions
sata_rcar: correct 'sata_rcar_sht'
sata_rcar: kill superfluous code in sata_rcar_bmdma_fill_sg()
libata: do not limit R-Car SATA driver to shmobile
ata: use platform_{get,set}_drvdata()
AHCI: Make distinct names for ports in /proc/interrupts
...
libata/for-3.10-fixes never got submitted during v3.10 cycle. Merge
it into for-3.11 so that it can be routed together with other changes
scheduled for v3.11.
Three trivial conflicts in drivers/ata/sata_rcar.c. All are caused by
1b20f6a9ad ("sata_rcar: add 'base' local variable to some functions")
conflicting with logic updates in for-3.10-fixes. The offending
commit simply adds local variable @base on functions which
dereferences sata_rcar_priv->base multiple times. The resolutions are
trivial - applying s/priv->base/base/ in the conflicting logic
updates.
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 30dcf76acc "libata: migrate ACPI code over to new bindings"
mistakenly dropped the code to register hotplug notificaion handler
for ATA port/devices, causing regression for people using ATA bay,
as kernel bug #59871 shows.
Fix this by adding back the hotplug notification handler registration
code. Since this code has to be run once and notification needs to
be installed on every ATA port/devices handle no matter if there is
actual device attached, we can't do this in binding time for ATA
device ACPI handle, as the binding only occurs when a SCSI device is
created, i.e. there is device attached. So introduce the
ata_acpi_hotplug_init() function to loop scan all ATA ACPI handles
and if it is available, install the notificaion handler for it during
ATA init time.
With the ATA ACPI handle binding to SCSI device tree, it is possible
now that when the SCSI hotplug work removes the SCSI device, the ACPI
unbind function will find that the corresponding ACPI device has
already been deleted by dock driver, causing a scaring message like:
[ 128.263966] scsi 4:0:0:0: Oops, 'acpi_handle' corrupt
Fix this by waiting for SCSI hotplug task finish in our notificaion
handler, so that the removal of ACPI device done in ACPI unbind
function triggered by the removal of SCSI device is run earlier when
ACPI device is still available.
[rjw: Rebased]
References: https://bugzilla.kernel.org/show_bug.cgi?id=59871
Reported-bisected-and-tested-by: Dirk Griesbach <spamthis@freenet.de>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: 3.6+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0. If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.
Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.
To reduce overall code bloat, make the changes described above.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Some device require DMADIR to be enabled, but are not detected as such
by atapi_id_dmadir. One such example is "Asus Serillel 2"
SATA-host-to-PATA-device bridge: the bridge itself requires DMADIR,
even if the bridged device does not.
As atapi_dmadir module parameter can cause problems with some devices
(as per Tejun Heo's memory), enabling it globally may not be possible
depending on the hardware.
This patch adds atapi_dmadir in the form of a "force" horkage value,
allowing global, per-bus and per-device control.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
While registering host controller track port number based upon number
of ports available on the controller, export port_no attribute through
/sys. This patch is needed by udev for composing persistent links in
/dev/disk/by-path.
/sys/devices/pci0000:00/0000:00:1f.2/ata8/ata_port/ata8
total 0
lrwxrwxrwx. 1 root root 0 Mar 6 12:43 device -> ../../../ata8
-r--r--r--. 1 root root 4096 Mar 6 12:43 idle_irq
-r--r--r--. 1 root root 4096 Mar 6 12:43 nr_pmp_links
-r--r--r--. 1 root root 4096 Mar 6 12:43 port_no
drwxr-xr-x. 2 root root 0 Mar 6 12:42 power
lrwxrwxrwx. 1 root root 0 Mar 6 12:41 subsystem -> ../../../../../../class/ata_port
-rw-r--r--. 1 root root 4096 Mar 6 12:40 uevent
1
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Jeff moved on to a greener pasture.
s/Maintained by: Jeff Garzik/Maintained by: Tejun Heo/g
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Commit 803739d25c ("[libata] replace
sata_settings with devslp_timing"), which was also Cc: stable, used a
stack buffer to receive data from ata_read_log_page(), which triggers
the following warning:
ahci 0000:00:1f.2: DMA-API: device driver maps memory fromstack [addr=ffff880140469948]
Fix this by using ap->sector_buf instead of a stack buffer.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For system freeze, if the port is already runtime suspended, leave it
alone and just return. The port will be resumed on thaw before it will
be used.
And since we will call get_noresume for every device during prepare
phase, and the port is resumed during thaw phase, it can't be in runtime
suspended state during the poweroff phase. So remove the
runtime_suspended check in poweroff callback.
And for all suspend(freeze/suspend/poweroff/etc.), there is no need to
touch the device, so set no_autopsy and no_recovery for them all.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We need to do different things for system PM and runtime PM, e.g. we do
not need to enable runtime wake for ZPODD when we are doing system
suspend, etc.
Currently, we use PMSG_SUSPEND for both system suspend and runtime
suspend and PMSG_ON for both system resume and runtime resume. Change
this by using PMSG_AUTO_SUSPEND for runtime suspend and PMSG_AUTO_RESUME
for runtime resume. And since PMSG_ON means no transition, it is changed
to PMSG_RESUME for ata port's system resume.
The ata_acpi_set_state is modified accordingly, and the sata case and
pata case is seperated for easy reading.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For ODDs, the upper layer will poll for media change every few
seconds, which will make it enter and leave suspend state very
often. And as each suspend will also cause a hard/soft reset,
the gain of runtime suspend is very little while the ODD may
malfunction after constantly being reset. So the idle callback
here will not proceed to suspend if a non-ZPODD capable ODD is
attached to the port.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ODD can be enabled for ZPODD if the following three conditions are
satisfied:
1 The ODD supports device attention;
2 The platform can runtime power off the ODD through ACPI;
3 The ODD is either slot type or drawer type.
For such ODDs, zpodd_init is called and a new structure is allocated for
it to store ZPODD related stuffs.
And the zpodd_dev_enabled function is used to test if ZPODD is currently
enabled for this ODD.
A new config CONFIG_SATA_ZPODD is added to selectively build ZPODD code.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
NCQ capability was used to check availability of SATA Settings page
from Identify Device Data Log, which contains DevSlp timing variables.
It does not work on some HDDs and leads to error messages.
IDENTIFY word 78 bit 5(Hardware Feature Control) can't work either
because it is only the sufficient condition of Identify Device data
log, not the necessary condition.
This patch replaced ata_device->sata_settings with ->devslp_timing
to only save DevSlp timing variables(8 bytes), instead of the whole
SATA Settings page(512 bytes).
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=51881
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This reverts commit de90cd71f6.
Shane Huang writes:
Please suspend this patch because I just received two new
DevSlp drives but found word 78 bit 5 is _not_ set.
I'm checking with the drive vendor whether he gave me
the wrong information. If bit 5 is not the necessary and
sufficient condition, I will implement another patch to
replace ata_device->sata_settings into ->devslp_timing.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This relatively simple boiler-plate code is repeated in several platform
drivers. We should implement a common version in libata.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_device->dma_mode's initial value is zero, which is not a valid dma
mode, but ata_dma_enabled will return true for this value. This patch
sets dma_mode to 0xff in reset function, so that ata_dma_enabled will
not return true for this case, or it will cause problem for pata_acpi.
The corrsponding bugzilla page is at:
https://bugzilla.kernel.org/show_bug.cgi?id=49151
Reported-by: Phillip Wood <phillip.wood@dunelm.org.uk>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Szymon Janc <szymon@janc.net.pl>
Tested-by: Dutra Julio <dutra.julio@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
NCQ capability was used to check availability of SATA Settings page
from Identify Device Data Log, which contains DevSlp timing variables.
It does not work on some HDDs and leads to error messages.
IDENTIFY word 78 bit 5(Hardware Feature Control) should be used.
Quoting SATA spec 3.1:
If Hardware Feature Control is supported, then:
a) IDENTIFY DEVICE data word 78 bit 5 (see 13.2.1.18) shall be
set to one;
b) the SET FEATURES Select Hardware Feature Control subcommand
shall be supported (see 13.3.8);
c) page 08h of the Identify Device Data log (see 13.7.7) shall
be supported;
This patch is not tested on SATA HDD with DevSlp supported.
Reported-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_timing_find_mode could return NULL which is not checked by all
low-level ATA drivers using it and cause a NULL ptr deref. Warn at least
so that possible issues can get fixed easily.
Signed-off-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a large set of updates, mostly for drivers (qla2xxx [including support
for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa, be2iscsi, isci,
lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas). There's also a rework for tape
adding virtually unlimited numbers of tape drives plus a set of dif fixes for
sd and a fix for a live lock on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQaqCFAAoJEDeqqVYsXL0MKJ4IALg/Obnk0/fNvBUNIrh5zRmj
r9UlXFJnlEDT03qRGdn8okgWMChbgaD1ZrwDTQnjNsabVQoTXI6oO6/uL2c8crpY
BFBwJvkNJS99nbcZv10CpJ3K7ykmRnKlkYon12iknhGwdtU+XJ14Z4PUcZkI9jmg
sBQQ6uNVWyosaONNE+k6o+dw6OTttJkzRX8e9in3thstxNTcG+h9iB1zZ/ETkSEj
tD4MyOgDiPf8kPV2awQThQGpni9Tu3SQr5dEn/iUUktUjiYsDNQuyaAk+QzyhUU7
D35iIJnIHlXTSTMQkrG4qpJHBvqPkWlYJzaOmheQryQ3vzp2C5Ly/hS9il45uIQ=
=49u9
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This is a large set of updates, mostly for drivers (qla2xxx [including
support for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa,
be2iscsi, isci, lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas).
There's also a rework for tape adding virtually unlimited numbers of
tape drives plus a set of dif fixes for sd and a fix for a live lock
on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
Fix up trivial conflict in drivers/scsi/qla2xxx/qla_nx.c due to new PCI
helper function use in a function that was removed by this pull.
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (198 commits)
[SCSI] st: remove st_mutex
[SCSI] sd: Ensure we correctly disable devices with unknown protection type
[SCSI] hpsa: gen8plus Smart Array IDs
[SCSI] qla4xxx: Update driver version to 5.03.00-k1
[SCSI] qla4xxx: Disable generating pause frames for ISP83XX
[SCSI] qla4xxx: Fix double clearing of risc_intr for ISP83XX
[SCSI] qla4xxx: IDC implementation for Loopback
[SCSI] qla4xxx: update copyrights in LICENSE.qla4xxx
[SCSI] qla4xxx: Fix panic while rmmod
[SCSI] qla4xxx: Fail probe_adapter if IRQ allocation fails
[SCSI] qla4xxx: Prevent MSI/MSI-X falling back to INTx for ISP82XX
[SCSI] qla4xxx: Update idc reg in case of PCI AER
[SCSI] qla4xxx: Fix double IDC locking in qla4_8xxx_error_recovery
[SCSI] qla4xxx: Clear interrupt while unloading driver for ISP83XX
[SCSI] qla4xxx: Print correct IDC version
[SCSI] qla4xxx: Added new mbox cmd to pass driver version to FW
[SCSI] scsi_dh_alua: Enable STPG for unavailable ports
[SCSI] scsi_remove_target: fix softlockup regression on hot remove
[SCSI] ibmvscsi: Fix host config length field overflow
[SCSI] ibmvscsi: Remove backend abstraction
...
1) Apply -- and then revert -- the FUA feature. Caused
disk corruption in linux-next, proving it cannot be turned on by
default.
Net effect to upstream tree: zero
2) New AHCI platform driver sata_highbank
3) Improve SCSI MODE SENSE handling; support MODE SELECT
4) AHCI: support aggressive device sleep (power mgmt)
5) sata_fsl: minor fix
6) pata_arasan: clk support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=i3EH
-----END PGP SIGNATURE-----
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata changes from Jeff Garzik:
"Minor libata updates, nothing notable.
1) Apply -- and then revert -- the FUA feature. Caused disk
corruption in linux-next, proving it cannot be turned on by
default.
Net effect to upstream tree: zero
2) New AHCI platform driver sata_highbank
3) Improve SCSI MODE SENSE handling; support MODE SELECT
4) AHCI: support aggressive device sleep (power mgmt)
5) sata_fsl: minor fix
6) pata_arasan: clk support"
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: Fix warnings when no PCI
[libata] Makefile: Fix build error in sata_highbank
[libata] export ata_dev_set_feature()
libata-core: use ATA_LBA in ata_build_rw_tf()
ata/ahci_platform: Add clock framework support
pata_arasan: add Device Tree probing capability
pata_arasan: Add clk_{un}prepare() support
ata: add platform driver for Calxeda AHCI controller
sata_fsl: add workaround for data length mismatch on freescale V2 controller
ahci: implement aggressive SATA device sleep support
ata: define enum constants for IDENTIFY DEVICE
Revert "libata: enable SATA disk fua detection on default"
[libata] scsi: implement MODE SELECT command
[libata] scsi: support MODE SENSE request for changeable and default parameters
[libata] scsi: Remove unlikely() from FUA check
libata: enable SATA disk fua detection on default
Since READ/WRITE FPDMA QUEUED commands are 48-bit, bit 6 of the device register
means LBA, the same as for READ/WRITE DMA EXT commands. So use ATA_LBA instead
of the bare number in ata_build_rw_tf()'s branch dedicated to the NCQ commands.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Device Sleep is a feature as described in AHCI 1.3.1 Technical Proposal.
This feature enables an HBA and SATA storage device to enter the DevSleep
interface state, enabling lower power SATA-based systems.
Aggressive Device Sleep enables the HBA to assert the DEVSLP signal as
soon as there are no commands outstanding to the device and the port
specific Device Sleep idle timer has expired. This enables autonomous
entry into the DevSleep interface state without waiting for software
in power sensitive systems.
This patch enables Aggressive Device Sleep only if both host controller
and device support it.
Tested on AMD reference board together with Device Sleep supported device
sample.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Reviewed-by: Aaron Lu <aaron.lwe@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
commit d70e551c8e, Add " 2GB ATA Flash
Disk"/"ADMA428M" to DMA blacklist, should have added a space before 2GB.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libsas and ipr pass flags to ata_host_init that are meant for the port.
ata_host flags:
ATA_HOST_SIMPLEX = (1 << 0), /* Host is simplex, one DMA channel per host only */
ATA_HOST_STARTED = (1 << 1), /* Host started */
ATA_HOST_PARALLEL_SCAN = (1 << 2), /* Ports on this host can be scanned in parallel */
ATA_HOST_IGNORE_ATA = (1 << 3), /* Ignore ATA devices on this host. */
flags passed by libsas:
ATA_FLAG_SATA = (1 << 1),
ATA_FLAG_PIO_DMA = (1 << 7), /* PIO cmds via DMA */
ATA_FLAG_NCQ = (1 << 10), /* host supports NCQ */
The only one that aliases is ATA_HOST_STARTED which is a 'don't care' in
the libsas and ipr cases since ata_hosts from these sources are not
registered with libata.
Reported-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Brian King <brking@us.ibm.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reuse ata_port_{suspend|resume}_common for sas. This path is chosen
over adding coordination between ata-tranport and sas-transport because
libsas wants to revalidate the domain at resume-time at the host level.
It can not validate links have resumed properly until libata has had a
chance to perform its revalidation, and any sane placing of an ata_port
in the sas-transport model would delay it's resumption until after the
host.
Export the common portion of port suspend/resume (bypass pm_runtime),
and allow sas to perform these operations asynchronously (similar to the
libsas async-ata probe implmentation). Async operation is determined by
having an external, rather than stack based, location for storing the
result of the operation.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jacek Danecki <jacek.danecki@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hotplug testing with libsas currently encounters a 55 second wait for
link recovery to give up. In the case where the user trusts the
response time of their devices permit the recovery attempts to be
limited to one.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently, SATA disk fua detection is disabled on default because most of
devices don't support this feature at that time. With the development of
technology, more and more SATA disks support this feature. So now we can enable
this detection on default.
Although fua detection is defined as a kernel module parameter, it is too hard
to set its value because it must be loaded and set before system starts up.
That needs to modify initrd file. So it is inconvenient for administrator who
needs to manage a huge number of servers.
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Michael Eitelwein writes:
I have an external SATA drive that was slowed down by bridge limits. I
found a solution in a thread on this list posted in 2008: It introduces
whitelist entries in libata-core.c for devices with well working bridges
(e.g. email on Fri, 31 Oct 2008 01:45:27 -0400).
I added my device to this whitelist in a custom built kernel and it
works fine for weeks now. How can I have this device added on the
whitelist within the official kernel? Is this whitelist mechanism still
supported or is there a smarter way to achieve whitelisting?
I added the following whitelist entry for my Buffalo DriveStation
Quattro "BUFFALO HD-QSU2/R5":
/* Devices that do not need bridging limits applied */
{ "MTRON MSP-SATA*", NULL, ATA_HORKAGE_BRIDGE_OK, },
{ "BUFFALO HD-QSU2/R5", NULL, ATA_HORKAGE_BRIDGE_OK, },
Reported-by: Michael Eitelwein <michael@eitelwein.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Two bits were appended to the end of the bitfield
list in struct scsi_device. Resolve that conflict
by including both bits.
Conflicts:
include/scsi/scsi_device.h
When using my Seagate FreeAgent GoFlex eSATAp external disk enclosure,
interface errors are always seen until 1.5Gbps is negotiated [1]. This
occurs using any disk in the enclosure, and when the disk is connected
directly with a generic passive eSATAp cable, we see stable 3Gbps
operation as expected.
Blacklist 3Gbps mode to avoid dataloss and the ~30s delay bus reset
and renegotiation incurs.
Signed-off-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When managing shost->host_eh_scheduled libata assumes that there is a
1:1 shost-to-ata_port relationship. libsas creates a 1:N relationship
so it needs to manage host_eh_scheduled cumulatively at the host level.
The sched_eh and end_eh port port ops allow libsas to track when domain
devices enter/leave the "eh-pending" state under ha->lock (previously
named ha->state_lock, but it is no longer just a lock for ha->state
changes).
Since host_eh_scheduled indicates eh without backing commands pinning
the device it can be deallocated at any time. Move the taking of the
domain_device reference under the port_lock to guarantee that the
ata_port stays around for the duration of eh.
Reviewed-by: Jacek Danecki <jacek.danecki@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
