Set card.fully_routed to request the ASoC core calculated unused codec
pins, and call snd_soc_dapm_nc_pin() for them. Remove the open-coded
calls.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Set card.fully_routed to request the ASoC core calculated unused codec
pins, and call snd_soc_dapm_nc_pin() for them. Remove the open-coded
calls.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A card is fully routed if the DAPM route table describes all connections on
the board.
When a card is fully routed, some operations can be automated by the ASoC
core. The first, and currently only, such operation is described below, and
implemented by this patch.
Codecs often have a large number of external pins, and not all of these pins
will be connected on all board designs. Some machine drivers therefore call
snd_soc_dapm_nc_pin() for all the unused pins, in order to tell the ASoC core
never to activate them.
However, when a card is fully routed, the information needed to derive the
set of unused pins is present in card->dapm_routes. In this case, have
the ASoC core automatically call snd_soc_dapm_nc_pin() for each unused
codec pin.
This has been tested with soc/tegra/tegra_wm8903.c and soc/tegra/trimslice.c.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When devices are instantiated from device-tree, pdev->id is set to -1.
Rework the driver so it doesn't depend on the ID.
Tegra I2S instantiated from board files are configured with pdev
name "tegra-i2s" and ID 0 or 1. The driver core then names the
device "tegra-i2s.0" or "tegra-i2s.1". This is not changing.
When a device is instantiated from device-tree, it will have
pdev->name="" and pdev->id=-1. For this reason, the pdev->id value is
not something we can rely on.
This patch doesn't actually change any names though:
When a device is instantiated from device-tree, the overall device name
will be "${unit_address}.${node_name}". This causes issues such as
clk_get() failures due to lack of a device-name match. To solve that,
AUXDATA was invented, to force a specific device name, thus allowing
dev_name() to return the same as the non-device-tree case. Tegra
currently uses AUXDATA for the I2S controllers. Eventually, AUXDATA will
go away, most likely replaced by phandle-based references within the
device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are cases where there is no working codec on the soc-audio devices,
and snd_soc_suspend() will skip such device when suspending. Yet its
counterpart snd_soc_resume() does not check this, causing complaints
about spinlock lockup:
[ 176.726087] BUG: spinlock lockup on CPU#0, kworker/0:2/1067, d8ab82a8
[ 176.732539] [<80014a14>] (unwind_backtrace+0x0/0xec) from [<805b3fc8>] (dump_stack+0x20/0x24)
[ 176.741082] [<805b3fc8>] (dump_stack+0x20/0x24) from [<80322208>] (do_raw_spin_lock+0x118/0x158)
[ 176.749882] [<80322208>] (do_raw_spin_lock+0x118/0x158) from [<805b7874>] (_raw_spin_lock_irqsave+0x5c/0x68)
[ 176.759723] [<805b7874>] (_raw_spin_lock_irqsave+0x5c/0x68) from [<8002a020>] (__wake_up+0x2c/0x5c)
[ 176.768781] [<8002a020>] (__wake_up+0x2c/0x5c) from [<804a6de8>] (soc_resume_deferred+0x3c/0x2b0)
[ 176.777666] [<804a6de8>] (soc_resume_deferred+0x3c/0x2b0) from [<8004ee20>] (process_one_work+0x2e8/0x50c)
[ 176.787334] [<8004ee20>] (process_one_work+0x2e8/0x50c) from [<8004fd08>] (worker_thread+0x1c8/0x2e0)
[ 176.796566] [<8004fd08>] (worker_thread+0x1c8/0x2e0) from [<80053ec8>] (kthread+0xa4/0xb0)
[ 176.804843] [<80053ec8>] (kthread+0xa4/0xb0) from [<8000ea70>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 85e7652("ASoC: Constify snd_soc_dai_ops structs") accidentally
introduced a few duplicated consts. This patch cleans it up.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Just checking the code in cs42l51_fill_cache():
The cache pointer points to codec->reg_cache + 1.
I think it is because CS42L51_FIRSTREG is 0x01,
so codec->reg_cache[0] is not used here.
Then we read CS42L51_NUMREGS bytes to cache.
So we need reg_cache_size to be CS42L51_NUMREGS + 1.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_platform_driver saves some boiler-plate code.
The devm_ APIs remove the need to manually clean up allocations,
thus removing some code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_platform_driver saves some boiler-plate code.
The devm_ APIs remove the need to manually clean up allocations,
thus removing some code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 1ee46ebd("ASoC: Make the DAI ops constant in the DAI structure")
introduced the possibility to have constant DAI ops structures, yet this is
barley used in both existing drivers and also new drivers being submitted,
although none of them modifies its DAI ops structure. The later is not
surprising since existing drivers are often used as templates for new drivers.
So this patch just constifies all existing snd_soc_dai_ops structs to eliminate
the issue altogether.
The patch was generated with the following coccinelle semantic patch:
// <smpl>
@@
identifier ops;
@@
-struct snd_soc_dai_ops ops =
+const struct snd_soc_dai_ops ops =
{ ... };
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
SoC Audio support for PlayPaq with WM8510 got added in commit 9aaca9683b
("[ALSA] Revised AT32 ASoC Patch"). That support depends on
BOARD_PLAYPAQ. That Kconfig symbol didn't exist when that support got
added in v2.6.27. It still doesn't. It has never been possible to even
build this driver. Drop it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_platform_drive saves some boiler-plate code.
The devm_ APIs remove the need to manually clean up allocations,
thus removing some code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This removes potentially machine-specific routing knowledge from the
I2S driverinto the machine drivers, which is better equipped to know
what the appropriate routing configuration is.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_platform_drive saves some boiler-plate code.
The devm_ APIs remove the need to manually clean up allocations,
thus removing some code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit ac601555 ("ASoC: Return early with -EINVAL if invalid dai format is
detected") requires the machine driver to tell the CS4270 codec driver
whether the CS4270 should be configured for master or slave operation.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace the manual register restore mechanism in cs4270.c and call the
generic snd_soc_cache_sync() handler instead.
This factors code out in favour of core facilities and also fixes a
bus confusion that is most probably caused by intermixing i2c-regmap
functions and i2c_smbus_* accessors.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds <linux/modules.h> to fix following build errors.
sound/soc/codecs/wm8994.c: In function 'wm8994_readable':
sound/soc/codecs/wm8994.c:58: warning: unused variable 'wm8994'
sound/soc/samsung/smdk_wm8994.c:176: error: expected declaration specifiers or '...' before string constant
sound/soc/samsung/smdk_wm8994.c:176: warning: data definition has no type or storage class
sound/soc/samsung/smdk_wm8994.c:176: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
sound/soc/samsung/smdk_wm8994.c:176: warning: function declaration isn't a prototype
sound/soc/samsung/smdk_wm8994.c:177: error: expected declaration specifiers or '...' before string constant
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the case of ((max9877_regs[reg] >> shift) & mask) != val
but ((max9877_regs[reg2] >> shift) & mask) == val2,
current code does not update the registers.
Fix the logic to update registers if either val or val2 is changed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet:
The BIT[5:4] of ADC Control Register 2 is to control the word width.
00 = 25 Bits
01 = 20 Bits
10 = 16 Bits
11 = Invalid
Thus, the AD1836_ADC_WORD_OFFSET should be defined as 4.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Fix below smatch warning:
sound/soc/codecs/cs42l73.c +1030 cs42l73_set_dai_fmt(53) error: inv is never equal to 1024 (wrong type 0 - 255).
sound/soc/codecs/cs42l73.c +1032 cs42l73_set_dai_fmt(55) error: inv is never equal to 768 (wrong type 0 - 255).
sound/soc/codecs/cs42l73.c +1036 cs42l73_set_dai_fmt(59) error: inv is never equal to 1024 (wrong type 0 - 255).
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current code defines some bits with left shift to the proper bit defined in
datasheet, but some don't.
Unify the definition with proper left shift and adjust the code accordingly.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The driver only supports I2C so doesn't need to do things conditionally.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
They're all volatile so shouldn't have defaults and as we've got pages
into the DSP memory the registers themselves aren't that useful - a
further patch adding support for the DSPs will provide direct diagnostic
access to the DSP memories.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's done in cs42l73_set_bias_level when the dapm.bias_level is switching
from SND_SOC_BIAS_OFF to SND_SOC_BIAS_STANDBY.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return -ENODEV instead of 0 if device id mismatch.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Alexander Sverdlin <subaparts@yandex.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the array.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the arrays.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the array.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the arrays.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
