* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] stex: switch to block timeout
[SCSI] make scsi_eh_try_stu use block timeout
[SCSI] megaraid_sas: switch to block timeout
[SCSI] ibmvscsi: switch to block timeout
[SCSI] aacraid: switch to block timeout
[SCSI] zfcp: prevent double decrement on host_busy while being busy
[SCSI] zfcp: fix deadlock between wq triggered port scan and ERP
[SCSI] zfcp: eliminate race between validation and locking
[SCSI] zfcp: verify for correct rport state before scanning for SCSI devs
[SCSI] zfcp: returning an ERR_PTR where a NULL value is expected
[SCSI] zfcp: Fix opening of wka ports
[SCSI] zfcp: fix remote port status check
[SCSI] fc_transport: fix old bug on bitflag definitions
[SCSI] Fix hang in starved list processing
stex sets the timeout in its slave configure routine for all devices.
This now needs to update the request queue timeout in block.
Cc: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi_eh_try_stu() was still using the timeout parameter in the device
which is now not set (i.e. zero filled) meaning that it waited no time
at all for the start unit command to complete (leading the routine to
conclude failure every time). This lead to a 2.6.27 regression:
http://bugzilla.kernel.org/show_bug.cgi?id=12120
Where firewire devices that were non spec compliant wouldn't spin up.
Fix this by using the block queue timeout value instead.
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
megaraid_sas sets the timeout in its slave configure routine for devices
on special channels. This now needs to update the request queue timeout
in block.
Cc: "Yang, Bo" <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ibmvscsi sets the timeout in its slave configure routine for disk
devices. This now needs to update the request queue timeout in block.
Cc: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
aacraid updates the timeout in its slave configure routine if it is too
small. This now needs to update the request queue timeout in block.
Cc: AACRAID list <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
PCI side of driver should be devinit, not init
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code
if (shost->dma_channel != NO_ISA_DMA)
free_dma(shost->dma_channel);
in there is triggerable only if we have CONFIG_ISA (we only set ->dma_channel to
something other than NO_ISA_DMA under #ifdef CONFIG_ISA). OTOH, free_dma() is
not guaranteed to be there in absense of CONFIG_ISA. IOW, driver runs into
undefined symbols on PCI-but-not-ISA configs (e.g. on frv) and it's a false
positive.
Fix: put the entire if () under #ifdef CONFIG_ISA; behaviour doesn't change and
dependency on free_dma() disappears for !CONFIG_ISA.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Close possible infinite loop with interrupts off when devices are
added back to the starved list.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=11898
Reported-by: <alex.shi@intel.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
dpt_i2o.c::adpt_i2o_to_scsi() reads the value at (reply+5) which
should contain the length in bytes of the transferred data. This
would be correct if reply was a u32 *. However it is a void * here,
so we need to read the value at (reply+20) instead.
The value at (reply+5) is usually 0xff0000, which is apparently
'large enough' and didn't cause any trouble until 2.6.27 where
commit 427e59f09f
Author: James Bottomley <James.Bottomley@HansenPartnership.com>
Date: Sat Mar 8 18:24:17 2008 -0600
[SCSI] make use of the residue value
caused this to become visible through e.g. iostat -x .
Signed-off-by: Miquel van Smoorenburg <mikevs@xs4all.net>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Drivers want to be able to return DID_TRANSPORT_DISRUPTED and
have it do the right thing for commands like tape and passthrouh
as far as retries go. The LLDs previously used DID_BUS_BUSY or DID_ERROR
which followed the cmd->retries limit, but DID_TRANSPORT_DISRUPTED
was skipping that check so it could have caused a problem with tape
commands.
This patch has DID_TRANSPORT_DISRUPTED check the cmd->retries/cmd->allowed.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Reed noted
(https://bugzilla.novell.com/show_bug.cgi?id=421330) that the
driver was incorrectly returning a SUCCESS status if the driver's
request to the firmware to abort a command failed. By doing so,
the mid-layer believed, incorrectly, that the command has
completed and has been returned (ultimately clearing
scsi_cmnd.request_buffer) yet the driver still has the command.
What should correctly happen is a mid-layer escalation
(device-reset, etc.) of recovery during which the driver will
eventually return the outstanding commands to the mid-layer.
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For 23XX ISPs, max_vports may return an invalid value.
Do not honour it.
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use correct block size (4K) for erase command 0x20 for Atmel
Flash. Use dword addresses for determining sector boundary.
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi_cmnd->cmnd was changed from a static array to a pointer post
2.6.25. It breaks mega_internal_command():
static int
mega_internal_command(adapter_t *adapter, megacmd_t *mc, mega_passthru *pthru)
{
...
scb = &adapter->int_scb;
memset(scb, 0, sizeof(scb_t));
scmd = &adapter->int_scmd;
memset(scmd, 0, sizeof(Scsi_Cmnd));
sdev = kzalloc(sizeof(struct scsi_device), GFP_KERNEL);
scmd->device = sdev;
scmd->device->host = adapter->host;
scmd->host_scribble = (void *)scb;
scmd->cmnd[0] = MEGA_INTERNAL_CMD;
mega_internal_command() uses scsi_cmnd allocated internally so
scmd->cmnd is NULL here. This patch adds a static array for cdb to
adapter_t and uses it here. This also uses
scsi_allocate_command/scsi_free_command, the recommended way to
allocate struct scsi_cmnd since the driver might use sense_buffer in
struct scsi_cmnd.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: Boaz Harrosh <bharrosh@panasas.com>
Tested-by: Pascal Terjan <pterjan@gmail.com>
Reported-by: Pascal Terjan <pterjan@gmail.com>
Acked-by: "Yang, Bo" <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
fdomain_cs: Sort out modules with duplicate description
pcmcia: Whine harder about use of EXCLUSIVE
pcmcia: IRQ_TYPE_EXCLUSIVE is long obsoleted
The iscsi_ibft.c changes are almost certainly a bugfix as the
pointer 'ip' is a u8 *, so they never print the last 8 bytes
of the IPv6 address, and the eight bytes they do print have
a zero byte with them in each 16-bit word.
Other than that, this should cause no difference in functionality.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (21 commits)
[SCSI] sd: fix computation of the full size of the device
[SCSI] lib: string_get_size(): don't hang on zero; no decimals on exact
[SCSI] sun3x_esp: Convert && to ||
[SCSI] sd: remove command-size switching code
[SCSI] 3w-9xxx: remove unnecessary local_irq_save/restore for scsi sg copy API
[SCSI] 3w-xxxx: remove unnecessary local_irq_save/restore for scsi sg copy API
[SCSI] fix netlink kernel-doc
[SCSI] sd: Fix handling of NO_SENSE check condition
[SCSI] export busy state via q->lld_busy_fn()
[SCSI] refactor sdev/starget/shost busy checking
[SCSI] mptfusion: Increase scsi-timeouts, similariy to the LSI 4.x driver.
[SCSI] aic7xxx: Take the LED out of diagnostic mode on PM resume
[SCSI] aic79xx: user visible misuse wrong SI units (not disk size!)
[SCSI] ipr: use memory_read_from_buffer()
[SCSI] aic79xx: fix shadowed variables
[SCSI] aic79xx: fix shadowed variables, add statics
[SCSI] aic7xxx: update *_shipped files
[SCSI] aic7xxx: update .reg files
[SCSI] aic7xxx: introduce "dont_generate_debug_code" keyword in aicasm parser
[SCSI] scsi_dh: Initialize path state to be passive when path is not owned
...
When computing the full size of the device, we need to cast
sdkp->capacity before shifting, since in some configurations sector_t
can be a 32-bit number.
Also, change ffz(~x) to the more idiomatic ilog2(x).
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The pattern !E && !E->fld is nonsensical. The patch below updates this
according to the assumption that && should be ||. But perhaps another
solution was intended.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@disable and_comm@
expression E;
identifier fld;
@@
- !E && !E->fld
+ !E || !E->fld
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-By: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch (as1138) removes from sd.c some old code for switching from
10-byte commands to 6-byte commands. This code is redundant -- the
switching for READ and WRITE is already handled in
scsi_io_completion() and the switching for MODE SENSE is already
handled in scsi_mode_sense(). (There is no comparable switch for MODE
SELECT, but I doubt one is needed.)
Furthermore the other handlers do a better job; they check for
appropriate ASC and ASCQ values before blindly switching the size.
The code in sd.c is known to cause problems with some devices by
switching when it shouldn't.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Since the commit 50bed2e286 (sg: disable
interrupts inside sg_copy_buffer), no need to disable interrupts
before calling scsi_sg_copy_from_buffer. So we can simplify
twa_scsiop_execute_scsi_complete() a bit, which disables interrupts
just for scsi_sg_copy_from_buffer.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Adam Radford <linuxraid@amcc.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Since the commit 50bed2e286 (sg: disable
interrupts inside sg_copy_buffer), no need to disable interrupts
before calling scsi_sg_copy_from_buffer. So we can simplify
tw_transfer_internal, which disables interrupts just for
scsi_sg_copy_from_buffer.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>\
Acked-by: Adam Radford <linuxraid@amcc.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix kernel-doc warning: the function short description must be on one
line and the previous comment is not kernel-doc but it was confusing
scripts/kernel-doc.
Warning(lin2627-g3-kdocfixes//drivers/scsi/scsi_netlink.c:221): No description found for parameter 'skb'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The current handling of NO_SENSE check condition is the same as
RECOVERED_ERROR, and assumes that in both cases, the I/O was fully
transferred.
We have seen cases of arrays returning with NO_SENSE (no error), but
the I/O was not completely transferred, thus residual set. Thus,
rather than return good_bytes as the entire transfer, set good_bytes
to 0, so that the midlayer then applies the residual in calculating
the transfer, and for sd, will fail the I/O and fall into a retry
path.
Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch implements q->lld_busy_fn() for scsi mid layer to export
its busy state for request stacking drivers.
For efficiency, no lock is taken to check the busy state of
shost/starget/sdev, since the returned value is not guaranteed and
may be changed after request stacking drivers call the function,
regardless of taking lock or not.
When scsi can't dispatch I/Os anymore and needs to kill I/Os
(e.g. !sdev), scsi needs to return 'not busy'.
Otherwise, request stacking drivers may hold requests forever.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch refactors the busy checking codes of scsi_device,
Scsi_Host and scsi_target. There should be no functional change.
This is a preparation for another patch which exports scsi's busy
state to the block layer for request stacking drivers.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Take the Diag/Activity-LED of the HBA out of diagnostic mode on PM
resume after successful PM resume from standby and HBA restart, it
remained always on before. If something fails before complete
recovery, it should remain on, since it is a diagnostics LED, reason
for the used higher layer for the clear.
Signed-off-by: thomas.schorpp@gmail.com
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
MHZ not Mhz for SI unit pedants
Closes bug #6422
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
OK to just reuse the outer declaration as it is never used again.
drivers/scsi/aic7xxx/aic79xx_pci.c:340:12: warning: symbol 'devconfig' shadows an earlier one
drivers/scsi/aic7xxx/aic79xx_pci.c:299:12: originally declared here
targpcistat is always assigned just before use, remove the inner declaration.
drivers/scsi/aic7xxx/aic79xx_pci.c:486:9: warning: symbol 'targpcistat' shadows an earlier one
drivers/scsi/aic7xxx/aic79xx_pci.c:429:9: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Redeclared within different if/else blocks, safe to reuse the
original from beginning of function.
drivers/scsi/aic7xxx/aic79xx_core.c:2475:10: warning: symbol 'scbid' shadows an earlier one
drivers/scsi/aic7xxx/aic79xx_core.c:2399:10: originally declared here
drivers/scsi/aic7xxx/aic79xx_core.c:2586:10: warning: symbol 'scbid' shadows an earlier one
drivers/scsi/aic7xxx/aic79xx_core.c:2399:10: originally declared here
drivers/scsi/aic7xxx/aic79xx_core.c:2587:15: warning: symbol 'scb' shadows an earlier one
drivers/scsi/aic7xxx/aic79xx_core.c:2393:13: originally declared here
Use caminfo for the outer declaration, the redeclared version is
iterating over all initiator/target pairs (devices) which.
drivers/scsi/aic7xxx/aic79xx_core.c:8857:23: warning: symbol 'devinfo' shadows an earlier one
drivers/scsi/aic7xxx/aic79xx_core.c:8711:21: originally declared here
Forward declaration was already marked static, make the definition match.
drivers/scsi/aic7xxx/aic79xx_core.c:3693:1: warning: symbol 'ahd_devlimited_syncrate' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update .reg files, marking unused registers with dont_generate_debug_code.
Comment explains how to use it.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the path state to be passive when we learn that the controller does
not own the path to the LUN.
This will avoid sending even a single i/o thru the passive path at the
probe time.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
On Tue, 12 Aug 2008 15:08:14 +0200
Giuliano Pochini <pochini@shiny.it> wrote:
> Fujitsu magneto-optical drive, Adaptec 29160 and
> Linux Jay 2.6.26 #7 SMP Sun Aug 10 18:34:22 CEST 2008 ppc 7455, altivec supported PowerMac3,6 GNU/Linux
>
> When I insert a disk and I mount it, scsi_test_unit_ready() is called and
> the do-while loop gets sshdr->sense_key == UNIT_ATTENTION in the first
> cycle and 0 in the second one. So the if below misses the UNIT_ATTENTION
> and sdev->changed = 1 is not executed. At this point bad things can
> happen... I'm not sure how to fix this. Any clue ?
The problem is essentially caused by us eating UNIT_ATTENTION
conditions in scsi_test_unit_ready(). Fix by updating the ->changed
flag when this happens if the media is removable.
[pochini@shiny.it: updates to tidy up patch]
Signed-off-by: Giuliano Pochini <pochini@shiny.it>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
To keep the size of changesets sane we split the switch by drivers;
to keep the damn thing bisectable we do the following:
1) rename the affected methods, add ones with correct
prototypes, make (few) callers handle both. That's this changeset.
2) for each driver convert to new methods. *ALL* drivers
are converted in this series.
3) kill the old (renamed) methods.
Note that it _is_ a flagday; all in-tree drivers are converted and by the
end of this series no trace of old methods remain. The only reason why
we do that this way is to keep the damn thing bisectable and allow per-driver
debugging if anything goes wrong.
New methods:
open(bdev, mode)
release(disk, mode)
ioctl(bdev, mode, cmd, arg) /* Called without BKL */
compat_ioctl(bdev, mode, cmd, arg)
locked_ioctl(bdev, mode, cmd, arg) /* Called with BKL, legacy */
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (41 commits)
PCI: fix pci_ioremap_bar() on s390
PCI: fix AER capability check
PCI: use pci_find_ext_capability everywhere
PCI: remove #ifdef DEBUG around dev_dbg call
PCI hotplug: fix get_##name return value problem
PCI: document the pcie_aspm kernel parameter
PCI: introduce an pci_ioremap(pdev, barnr) function
powerpc/PCI: Add legacy PCI access via sysfs
PCI: Add ability to mmap legacy_io on some platforms
PCI: probing debug message uniformization
PCI: support PCIe ARI capability
PCI: centralize the capabilities code in probe.c
PCI: centralize the capabilities code in pci-sysfs.c
PCI: fix 64-vbit prefetchable memory resource BARs
PCI: replace cfg space size (256/4096) by macros.
PCI: use resource_size() everywhere.
PCI: use same arg names in PCI_VDEVICE comment
PCI hotplug: rpaphp: make debug var unique
PCI: use %pF instead of print_fn_descriptor_symbol() in quirks.c
PCI: fix hotplug get_##name return value problem
...
This merges branches irq/genirq, irq/sparseirq-v4, timers/hpet-percpu
and x86/uv.
The sparseirq branch is just preliminary groundwork: no sparse IRQs are
actually implemented by this tree anymore - just the new APIs are added
while keeping the old way intact as well (the new APIs map 1:1 to
irq_desc[]). The 'real' sparse IRQ support will then be a relatively
small patch ontop of this - with a v2.6.29 merge target.
* 'genirq-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (178 commits)
genirq: improve include files
intr_remapping: fix typo
io_apic: make irq_mis_count available on 64-bit too
genirq: fix name space collisions of nr_irqs in arch/*
genirq: fix name space collision of nr_irqs in autoprobe.c
genirq: use iterators for irq_desc loops
proc: fixup irq iterator
genirq: add reverse iterator for irq_desc
x86: move ack_bad_irq() to irq.c
x86: unify show_interrupts() and proc helpers
x86: cleanup show_interrupts
genirq: cleanup the sparseirq modifications
genirq: remove artifacts from sparseirq removal
genirq: revert dynarray
genirq: remove irq_to_desc_alloc
genirq: remove sparse irq code
genirq: use inline function for irq_to_desc
genirq: consolidate nr_irqs and for_each_irq_desc()
x86: remove sparse irq from Kconfig
genirq: define nr_irqs for architectures with GENERIC_HARDIRQS=n
...
Remove some open coded (and buggy) versions of pci_find_ext_capability
in favor of the real routine in the PCI core.
Tested-by: Tomasz Czernecki <czernecki@gmail.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We are using 28bit pci (bus/dev/fn + 12 bits) as irq number, so the
cache for irq number should be 32 bit too.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The driver flag dynids.use_driver_data is almost consistently not set,
and causes more problems than it solves. It was initially intended as a
flag to indicate whether a driver's usage of driver_data had been
carefully inspected and was ready for values from userspace. That audit
was never done, so most drivers just get a 0 for driver_data when new
IDs are added from userspace via sysfs. So remove the flag, allowing
drivers to see the data directly (a followon patch validates the passed
driver_data value against what the drivers expect).
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tejun's commit 7b595756ec made sysfs
attribute->owner unnecessary. But the field was left in the structure to
ease the merge. It's been over a year since that change and it is now
time to start killing attribute->owner along with its users - one arch at
a time!
This patch is attempt #1 to get rid of attribute->owner only for
CONFIG_X86_64 or CONFIG_X86_32 . We will deal with other arches later on
as and when possible - avr32 will be the next since that is something I
can test. Compile (make allyesconfig / make allmodconfig / custom config)
and boot tested.
akpm: the idea is that we put the declaration of sttribute.owner inside
`#ifndef CONFIG_X86'. But that proved to be too ambitious for now because
new usages kept on turning up in subsystem trees.
[akpm: remove the ifdef for now]
Signed-off-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change sr_vendor.c to use the new bcd2bin function instead of the obsolete
BCD2BIN macro.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PCMCIA one provides its own description so in PCMCIA mode we should use
that.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Turn ide_driver_t's 'proc' field into ->proc_entries method
(and also 'settings' field into ->proc_devsets method). Then
update all device drivers accordingly.
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Now that device_create() has been audited, rename things back to the
original call to be sane.
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
we are using 28bit pci (bus/dev/fn + 12 bits) as irq number, so the
cache for irq number should be 32 bit too.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch removes the Hades support that was marked as BROKEN 5 years ago.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (66 commits)
ata: Add documentation for hard disk shock protection interface (v3)
ide: Implement disk shock protection support (v4)
ide-cd: fix printk format warning
piix: add Hercules EC-900 mini-notebook to ich_laptop short cable list
ide-atapi: assign taskfile flags per device type
ide-cd: move cdrom_info.dma to ide_drive_t.dma
ide: add ide_drive_t.dma flag
ide-cd: add a debug_mask module parameter
ide-cd: convert driver to new ide debugging macro (v3)
ide: move SFF DMA code to ide-dma-sff.c
ide: cleanup ide-dma.c
ide: cleanup ide_build_dmatable()
ide: remove needless includes from ide-dma.c
ide: switch to DMA-mapping API part #2
ide: make ide_dma_timeout() available also for CONFIG_BLK_DEV_IDEDMA_SFF=n
ide: make ide_dma_lost_irq() available also for CONFIG_BLK_DEV_IDEDMA_SFF=n
ide: __ide_dma_end() -> ide_dma_end()
pmac: remove needless pmac_ide_destroy_dmatable() wrapper
pmac: remove superfluous pmif == NULL checks
ide: Two fixes regarding memory allocation
...
Set IDE_AFLAG_DRQ_INTERRUPT in do_identify() instead of ATAPI
device drivers *_setup() methods.
While at it:
- use ata_id_cdb_intr()
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add 'unsigned long dev_flags' to ide_drive_t and convert bitfields
to IDE_DFLAG_* flags.
While at it:
- IDE_DFLAG_ADDRESSING -> IDE_DFLAG_LBA48
- fixup some comments
- remove needless g->flags zeroing from ide*_probe()
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ->ticks field from struct ide_floppy_obj to ide_drive_t.
* Move idefloppy_transfer_pc() to ide-atapi.c and make
ide_transfer_pc() use it.
* Always use ide_transfer_pc as a handler in ide_issue_pc().
* Remove no longer used idefloppy_start_pc_transfer(),
ide*_transfer_pc() and 'handler' argument from ide_issue_pc().
* Make ide_transfer_pc() static.
While at it:
* idefloppy_transfer_pc() -> ide_delayed_transfer_pc()
* IDEFLOPPY_TICKS_DELAY -> IDEFLOPPY_PC_DELAY
* ->ticks -> ->pc_delay
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Always use ide_pc_intr as a handler in ide_pc_intr().
* Remove no longer used ide*_pc_intr() and 'handler'
argument from ide_{transfer_pc,pc_intr}().
* Make ide_pc_intr() static.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->pc_{update,io}_buffers methods to ide_drive_t and use
them instead of {update,io}_buffers ide_pc_intr() arguments.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_create_request_sense_cmd() and ide_retry_pc() helpers
and convert ide-{atapi,floppy,tape}.c to use them.
* Remove no longer used ide*_create_request_sense_cmd(),
ide*_retry_pc() and 'retry_pc' argument from ide_pc_intr().
* Make ide_queue_pc_head() static.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move idescsi_expiry() to ide-atapi.c.
* Move get_timeout() to <linux/ide.h>.
* Drop 'timeout' and 'expiry' arguments from ide_pc_intr().
While at it:
* idescsi_expiry() -> ide_scsi_expiry()
* get_timeout() -> ide_scsi_get_timeout()
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add pointer to the current packet command (struct ide_atapi_pc *pc)
to ide_drive_t and use it instead of the pointer in struct ide_*_obj.
* Use drive->pc in ide_{issue,transfer}_pc() and ide_pc_intr()
instead of 'pc' argument.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'int dsc' argument to ->pc_callback method.
* Call ide_tape_handle_dsc() internally in ide_tape_callback()
if dsc argument is set and update ide_pc_intr() accordingly.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We must be using the bh spin locking functions in
iscsi_eh_device_reset becuase the session lock interacts with
a thread and softirq.
This patch also fixes up a bogus comment and check in fail_command,
because no one drops the lock (bnx2i did but it is not going
upstream yet and there were other refcount changes for that).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some wires got crossed on some patches and I messed up in the code
below when rebuilding a patch. We want to be checking if flag
equaled the value indicating if we killing the session due to
final logout or if we just trying to relogin.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The segment->done functions return a iscsi error value which gives
a lot more info than conn failed, so this patch has us return
that value. I also add a new one for xmit failures.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
I had this in my patchset to add target reset support, but
it got dropped due to patching conflicts. This initial patch
just renames the function and users. We are actually just
dropping the session, and so this does not have anything to do
with the host exactly. It does for software iscsi because
we allocate a host per session, but for cxgb3i this makes no
sense.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some endpoint code was using unsigned int and some
was using uint64_t. This converts it all to uint64_t.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If the driver knows when hardware is removed like with cxgb3i,
bnx2i, qla4xxx and iser then we will want to remove the sessions/devices
that are bound to that device before removing the host.
cxgb3i and in the future bnx2i will remove the host and that will
remove all the sessions on the hba. iser can call iscsi_kill_session
when it gets an event that indicates that a hca is removed.
And when qla4xxx is hooked in to the lib (it is only hooked into
the class right now) it can call iscsi remove host like the
partial offload card drivers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
iscsi_tcp was updating the exp_statsn (exp_statsn acknowledges
status and tells the target it is ok to let the resources for
a iscsi pdu to be reused) before it got all the data for pdu read
into OS buffers. Data corruption was occuring if something happens
to a packet and the network layer requests a retransmit, and the
initiator has told the target about the udpated exp_statsn ack,
then the target may be sending data from a buffer it has reused
for a new iscsi pdu. This fixes the problem by having the LLD
(iscsi_tcp in this case) just handle the transferring of data, and
has libiscsi handle the processing of status (libiscsi completion
processing is done after LLD data transfers are complete).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For some reason these messages ended up being printed with KERN_INFO
rendering them invisible to pretty much everyone. Switch to
KERN_NOTICE.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The old detection code couldn't handle all possible combinations of
DIX and DIF. This version does, giving priority to DIX if the
controller is capable.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Now that we no longer use protection_type as trigger for preparing
protected CDBs we can remove the places that set it to zero. This
allows userland to see which protection type the device is formatted
with regardless of whether the HBA supports DIF or not.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use the same logic to prepare RD/WRPROTECT and the protection
operation. Fixes a corner case where we could issue an unprotected
CDB and yet tell the HBA to do DIF to the drive.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There's a target reset bug.
This loop:
for (id = 0; id <= shost->max_id; id++) {
Never terminates if shost->max_id is set to ~0, like aic94xx does.
It's also pretty inefficient since you mostly have compact target
numbers, but the max_id can be very high. The best way would be to
sort the recovery list by target id and skip them if they're equal,
but even a worst case O(N^2) traversal is probably OK here, so fix it
by finding the next highest target number (assuming n+1) and
terminating when there isn't one.
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Added support for new sysfs attributes: lpfc_stat_data_ctrl and
lpfc_max_scsicmpl_time. The attributes control statistical reporting
of io load.
Added support for new fc vendor events for error reporting.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Added new sysfs attribute lpfc_max_scsicmpl_time. Attribute, when enabled,
will control target queue depth based on I/O completion time.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Revert the target busy response in favor of the transport disrupted
response for node state transitions.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We do not need to set REQ_NOMERGE because when the module calls
blk_execute_rq -> blk_execute_rq_nowait, blk_execute_rq_nowait sets
it for us. This brings all the modules in sync for those bits.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
