This puts the window counter computation [RFC 4342, 8.1] into a separate
function which is called whenever a new packet is ready for immediate
transmission in ccid3_hc_tx_send_packet.
Justification:
The window counter update was previously computed after the packet was sent. This has
two drawbacks, both fixed by this patch:
1) re-compute another timestamp almost directly after the packet was sent (expensive),
2) the CCVal for the window counter is needed at the instant the packet is sent.
Further details:
The initialisation of the window counter is left in the state NO_SENT, as before.
The algorithm will do nothing if either RTT is initialised to 0 (which is ok) or if
the RTT value remains below 4 microseconds (which is almost pathological).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
CCID3 performance depends much on the accuracy of RTT samples. If RTT
samples grow too large, performance can be catastrophically poor.
To limit the amount of possible damage in such cases, the patch
* introduces an upper limit which identifies a maximum `sane' RTT value;
* uses a macro to enforce this upper limit.
Using a macro was given preference, since it is necessary to identify the
calling function in the warning message. Since exceeding this threshold
identifies a critical condition, DCCP_CRIT is used and not DCCP_WARN.
Many thanks to Ian McDonald for collaboration on this issue.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
In both the sender and the receiver it is possible that the stored
RTT value is accessed before an actual RTT estimate has been computed.
This patch
* initialises the sender RTT to 0
- the sender always accesses the RTT in ccid3_hc_tx_packet_sent
- the RTT is further needed for the window counter algorithm
* replaces the receiver initialisation of 5msec with 0
- which has the same effect and removes an `XXX'
- the RTT value is needed in ccid3_hc_rx_packet_recv as rtt_prev
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
The function ccid3_hc_tx_insert_options only does a redundant no-op,
as the operation
DCCP_SKB_CB(skb)->dccpd_ccval = hctx->ccid3hctx_last_win_count;
is already performed _unconditionally_ in ccid3_hc_tx_send_packet.
Since there is further no current need for this function, it is removed
entirely. Since furthermore, there is actually no present need for the
entire interface function ccid_hc_tx_insert_options, it was decided to
remove it also, to clean up the interface.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This is an optimisation to reduce CPU load. The received feedback is now
only directed to the active CCID component, without requiring processing
also by the inactive one.
As a consequence, a similar test in ccid3.c is now redundant and is
also removed.
Justification:
Currently DCCP works as a unidirectional service, i.e. a listening server
is not at the same time a connecting client.
As far as I can see, several modifications are necessary until that
becomes possible.
At the present time, received feedback is both fed to the rx/tx CCID
modules. In unidirectional service, only one of these is active at any
one time.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Problem:
Most target types in the CCID3 code are u32, so subtle conversion errors
can occur if signed time calculations yield negative results: the original
values are lost in the conversion to unsigned, calculation errors go undetected.
This patch therefore
* sets all critical time types from unsigned to suseconds_t
* avoids comparison between signed/unsigned via type-casting
* provides ample warning messages in case time calculations are negative
These warning messages can be removed at a later stage when the code
has undergone more testing.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This simplifies the calculation of a value p for a given fval when the
first loss interval is computed (RFC 3448, 6.3.1). It makes use of the
two new functions scaled_div/scaled_div32 to provide overflow protection.
Additionally, protection against divide-by-zero is extended - in this
case the function will return the maximally possible value of p=100%.
Background:
The maximum fval, f(100%), is approximately 244, i.e. the scaled value of fval
should never exceed 244E6, which fits easily into u32. The problem is the scaling
by 10^6, since additionally R(TT) is in microseconds.
This is resolved by breaking the division into two stages: the first stage
computes fval=(s*10^6)/R, stores that into u64; the second stage computes
fval = (fval*10^6)/X_recv and complains if overflow is reached for u32.
This case is safe since the TFRC reverse-lookup routine then returns p=100%.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This replaces the remaining uses of usecs_div with scaled_div32, which
internally uses 64bit division and produces a warning on overflow.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch
* resolves a bug where packets smaller than 32/64 bytes resulted in sending rates of 0
* supports all sending rates from 1/64 bytes/second up to 4Gbyte/second
* simplifies the present overflow problems in calculations
Current sending rate X and the cached value X_recv of the receiver-estimated
sending rate are both scaled by 64 (2^6) in order to
* cope with low sending rates (minimally 1 byte/second)
* allow upgrading to use a packets-per-second implementation of CCID 3
* avoid calculation errors due to integer arithmetic cut-off
The patch implements a revised strategy from
http://www.mail-archive.com/dccp@vger.kernel.org/msg01040.html
The only difference with regard to that strategy is that t_ipi is already
used in the calculation of the nofeedback timeout, which saves one division.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This fixes
1) a bug in the recomputation of the sending rate by the nofeedback
timer when no feedback at all has so far been sent by the receiver:
min_t was used instead of max_t, which is wrong (cf. RFC 3448, p. 10);
2) an error in the computation of larger initial windows: instead of
min(... max()) (cf. RFC 4342, 5.), the code had used max(... max()).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This performs two optimisations for the recomputation of the sending rate.
1) Currently the target sending rate X_calc is recalculated whenever
a) the nofeedback timer expires, or
b) a feedback packet is received.
In the (a) case, recomputing X_calc is redundant, since
* the parameters p and RTT do not change in between the
reception of feedback packets;
* the parameter X_recv is either modified from received
feedback or via the nofeedback timer;
* a test (`p == 0') in the nofeedback timer avoids using
a stale/undefined value of X_calc if p was previously 0.
2) The nofeedback timer now only recomputes a timestamp when p == 0.
This is according to step (4) of [RFC 3448, 4.3] and avoids
unnecessarily determining a timestamp.
A debug statement about not updating X is also removed - it helps very
little in debugging and just clutters the logs.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch follows a suggestion by Ian McDonald and ensures that in
the current code the value of p can not exceed 100%. Such a value is
illegal and would consequently cause a bug condition in tfrc_calc_x().
The receiver case is also tested, and a warning message is added.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
SLAB_ATOMIC is an alias of GFP_ATOMIC
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch deprecates the existing use of an arbitrary value TFRC_SMALLEST_P
for low-threshold values of p. This avoids masking low-resolution errors.
Instead, the code now checks against real boundaries (implemented by preceding
patch) and provides warnings whenever a real value falls below the threshold.
If such messages are observed, it is a better solution to take this as an
indication that the lookup table needs to be re-engineered.
Changelog:
----------
This patch
* makes handling all TFRC resolution errors local to the TFRC library
* removes unnecessary test whether X_calc is 'infinity' due to p==0 -- this
condition is already caught by tfrc_calc_x()
* removes setting ccid3hctx_p = TFRC_SMALLEST_P in ccid3_hc_tx_packet_recv
since this is now done by the TFRC library
* updates BUG_ON test in ccid3_hc_tx_no_feedback_timer to take into account
that p now is either 0 (and then X_calc is irrelevant), or it is > 0; since
the handling of TFRC_SMALLEST_P is now taken care of in the tfrc library
Justification:
--------------
The TFRC code uses a lookup table which has a bounded resolution.
The lowest possible value of the loss event rate `p' which can be
resolved is currently 0.0001. Substituting this lower threshold for
p when p is less than 0.0001 results in a huge, exponentially-growing
error. The error can be computed by the following formula:
(f(0.0001) - f(p))/f(p) * 100 for p < 0.0001
Currently the solution is to use an (arbitrary) value
TFRC_SMALLEST_P = 40 * 1E-6 = 0.00004
and to consider all values below this value as `virtually zero'. Due to
the exponentially growing resolution error, this is not a good idea, since
it hides the fact that the table can not resolve practically occurring cases.
Already at p == TFRC_SMALLEST_P, the error is as high as 58.19%!
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This avoids a (harmless) warning message being printed at the DCCP server
(the receiver of a DCCP half connection).
Incoming packets are both directed to
* ccid_hc_rx_packet_recv() for the server half
* ccid_hc_tx_packet_recv() for the client half
The message gets printed since on a server the client half is currently not
sending data packets.
This is resolved for the moment by checking the DCCP-role first. In future
times (bidirectional DCCP connections), this test may have to be more
sophisticated.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
The main object of this patch is the following bug:
==> In ccid3_hc_tx_packet_recv, the parameters p and X_recv were updated
_after_ the send rate was calculated. This is clearly an error and is
resolved by re-ordering statements.
In addition,
* r_sample is converted from u32 to long to check whether the time difference
was negative (it would otherwise be converted to a large u32 value)
* protection against RTT=0 (this is possible) is provided in a further patch
* t_elapsed is also converted to long, to match the type of r_sample
* adds a a more debugging information regarding current send rates
* various trivial comment/documentation updates
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This bug resulted in ccid3_hc_tx_send_packet returning negative
delay values, which in turn triggered silently dequeueing packets in
dccp_write_xmit. As a result, only a few out of the submitted packets made
it at all onto the network. Occasionally, when dccp_wait_for_ccid was
involved, this also triggered a bug warning since ccid3_hc_tx_send_packet
returned a negative value (which in reality was a negative delay value).
The cause for this bug lies in the comparison
if (delay >= hctx->ccid3hctx_delta)
return delay / 1000L;
The type of `delay' is `long', that of ccid3hctx_delta is `u32'. When comparing
negative long values against u32 values, the test returned `true' whenever delay
was smaller than 0 (meaning the packet was overdue to send).
The fix is by casting, subtracting, and then testing the difference with
regard to 0.
This has been tested and shown to work.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
The TFRC nofeedback timer normally expires after the maximum of 4
RTTs and twice the current send interval (RFC 3448, 4.3). On LANs
with a small RTT this can mean a high processing load and reduced
performance, since then the nofeedback timer is triggered very
frequently.
This patch provides a configuration option to set the bound for the
nofeedback timer, using as default 100 milliseconds.
By setting the configuration option to 0, strict RFC 3448 behaviour
can be enforced for the nofeedback timer.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch implements a suggestion by Ian McDonald and
1) Avoids tests against negative packet lengths by using unsigned int
for packet payload lengths in the CCID send_packet()/packet_sent() routines
2) As a consequence, it removes an now unnecessary test with regard to `len > 0'
in ccid3_hc_tx_packet_sent: that condition is always true, since
* negative packet lengths are avoided
* ccid3_hc_tx_send_packet flags an error whenever the payload length is 0.
As a consequence, ccid3_hc_tx_packet_sent is never called as all errors
returned by ccid_hc_tx_send_packet are caught in dccp_write_xmit
3) Removes the third argument of ccid_hc_tx_send_packet (the `len' parameter),
since it is currently always set to skb->len. The code is updated with regard
to this parameter change.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This implements the larger-initial-windows feature for CCID 3, as described in
section 5 of RFC 4342. When the first feedback packet arrives, the sender can
send up to 2..4 packets per RTT, instead of just one.
The patch further
* reduces the number of timestamping calls by passing the timestamp value
(which is computed in one of the calling functions anyway) as argument
* renames one constant with a very long name into one which is shorter and
resembles the one in RFC 3448 (t_mbi)
* simplifies some of the min_t/max_t cases where both `x', `y' have the same
type
Commiter note: renamed TFRC_t_mbi to TFRC_T_MBI, to follow Linux coding style.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This corrects the setting of the nofeedback timer with regard to RFC
3448 - previously it was not set to max(4*R, 2*s/X) as specified. Using
the maximum of 1 second as upper bound (as it was done before) can have
detrimental effects, especially if R is small.
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch
* removes setting t_RTO in ccid3_hc_tx_init (per [RFC 3448, 4.2], t_RTO is
undefined until feedback has been received);
* makes some trivial changes (updates of comments);
* performs a small optimisation by exploiting that the feedback timeout
uses the value of t_ipi. The way it is done is safe, because the timeouts
appear after the changes to t_ipi, ensuring that up-to-date values are used;
* in ccid3_hc_tx_packet_recv, moves the t_rto statement closer to the calculation
of the next_tmout. This makes the code clearer to read and is also safe, since
t_rto is not updated until the next call of ccid3_hc_tx_packet_recv, and is not
read by the functions called via ccid_wait_for_ccid();
* removes a `max' statement in sk_reset_timer, this is not needed since the timeout
value is always greater than 1E6 microseconds.
* adds `XXX'es to highlight that currently the nofeedback timer is set
in a non-standard way
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch:
* consolidates updating of parameters (t_nom, t_ipi, t_delta) which
need to be updated at the same time, since they are inter-dependent
* removes two inline functions which are no longer needed as a result of
the above consolidation
* resolves a FIXME regarding the re-calculation of t_ipi within the nofeedback
timer, in the state where no feedback has previously been received
* ties updating these parameters to updating the sending rate X, exploiting
that all three parameters in turn depend on X; and using a small optimisation
which can reduce the number of required instructions: only update the three
parameters when X really changes
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch concerns updating the value of the nofeedback timer when no feedback
has been received so far.
Since in this case the value of R is still undefined according to [RFC 3448,
4.2], we can not perform step (3) of [RFC 3448, 4.3]. A clarification is
provided in [RFC 4342, sec. 5], which states that in these cases the nofeedback
timer (still) expires "after two seconds".
Many thanks to Ian McDonald for pointing this out and providing the
clarification.
The patch
* implements [RFC 4342, sec. 5] with regard to the above case
* consolidates handling timer restart by
- adding an appropriate jump label and
- initialising the timeout value
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This considers the case - ACK received while no packet has been sent
so far. Resolved by printing a (rate-limited) warning message.
Further removes an unnecessary BUG_ON in ccid3_hc_tx_packet_recv,
received feedback on a terminating connection is simply ignored.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch removes a switch statement which is redundant since,
* nothing is done in states TFRC_SSTATE_NO_SENT/TFRC_SSTATE_NO_FBACK
* it is impossible that the function is called in the state TFRC_SSTATE_TERM, since
--the function is called, in dccp_write_xmit, after ccid3_hc_tx_send_packet
--if ccid3_hc_tx_send_packet is called in state TFRC_SSTATE_TERM, it returns
-EINVAL, which means that ccid3_hc_tx_packet_sent will not be called
(compare dccp_write_xmit)
--> therefore, this case is logically impossible
* the remaining state is TFRC_SSTATE_FBACK which conditionally updates t_ipi, t_nom,
and t_delta. This is a no-op, since
--t_ipi only changes when feedback is received
--however, when feedback arrives via ccid3_hc_tx_packet_recv, there is an identical
code block which performs the same set of operations
--performing the same set of operations again in ccid3_hc_tx_packet_sent therefore
does not change anything, since between the time of receiving the last feedback
(and therefore update of t_ipi, t_nom, and t_delta), the value of t_ipi has not
changed
--since t_ipi has not changed, the values of t_delta and t_nom also do not change,
they depend fully on t_ipi
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This resolves an `XXX' in ccid3_hc_tx_send_packet().
The function is only called on Data and DataAck packets and returns a negative
result on zero-sized messages. This is a reasonable policy since CCID 3 is a
congestion-control module and congestion control on zero-sized Data(Ack)
packets is in a way pathological.
The patch uses a more suitable error code for this case, it returns the Posix.1
code `EBADMSG' ("Not a data message") instead of `ENOTCONN'.
As a result of ignoring zero-sized packets, a the condition for a warning
"First packet is data" in ccid3_hc_tx_packet_sent is always satisfied; this
message has been removed since it will always be printed.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This makes some logically equivalent simplifications, by replacing
rc - values plus goto's with direct return statements.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch performs a simplifying (performance) optimisation:
In each call of the inline function ccid3_calc_new_t_ipi(), the state is
tested against TFRC_SSTATE_NO_FBACK. This is expensive when the function
is called very often. A simpler solution, implemented by this patch, is
to adapt the control flow.
Background:
This removes a non-referenced variable.
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This reaps the benefit of the earlier patch, which changed the type of
CCID 3 states to use enums, in that many conditions are now simplified
and the number of possible (unexpected) values is greatly reduced.
In a few instances, this also allowed to simplify pre-conditions; where
care has been taken to retain logical equivalence.
[DCCP]: Introduce a consistent BUG/WARN message scheme
This refines the existing set of DCCP messages so that
* BUG(), BUG_ON(), WARN_ON() have meaningful DCCP-specific counterparts
* DCCP_CRIT (for severe warnings) is not rate-limited
* DCCP_WARN() is introduced as rate-limited wrapper
Using these allows a faster and cleaner transition to their original
counterparts once the code has matured into a full DCCP implementation.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This adds a CCID3 debug option to the configuration menu
which is missing in Kconfig, but already used by the code.
CCID 2 already provides such an entry.
To enable debugging, set CONFIG_IP_DCCP_CCID3_DEBUG=y
NOTE: The use of ccid3_{t,r}x_state_name is safe, since
now only enum values can appear.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch tackles the following problem:
* the ccid3_hc_{t,r}x_sock define ccid3hc{t,r}x_state as `u8', but
in reality there can only be a few, pre-defined enum names
* this necessitates addiditional checking for unexpected values
which would otherwise be caught by the compiler
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Updates the references to spec documents throughout the code, taking into
account that
* the DCCP, CCID 2, and CCID 3 drafts all became RFCs in March this year
* RFC 1063 was obsoleted by RFC 1191
* draft-ietf-tcpimpl-pmtud-0x.txt was published as an Informational
RFC, RFC 2923 on 2000-09-22.
All references verified.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With constants for CCID numbers this now uses them in some places.
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
As Arnaldo Carvalho de Melo points out I should be using list_entry in case
the structure changes in future. Current code functions but is reliant
on position and requires type cast.
Noticed when doing this that I have one more variable than I needed so
removing that also.
Signed off by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes CCID3 to give much closer performance to RFC4342.
CCID3 is meant to alter sending rate based on RTT and loss.
The performance was verified against:
http://wand.net.nz/~perry/max_download.php
For example I tested with netem and had the following parameters:
Delayed Acks 1, MSS 256 bytes, RTT 105 ms, packet loss 5%.
This gives a theoretical speed of 71.9 Kbits/s. I measured across three
runs with this patch set and got 70.1 Kbits/s. Without this patchset the
average was 232 Kbits/s which means Linux can't be used for CCID3 research
properly.
I also tested with netem turned off so box just acting as router with 1.2
msec RTT. The performance with this is the same with or without the patch
at around 30 Mbit/s.
Signed off by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
And not the silly LIMIT_NETDEBUG and silently return without inserting
the option requested.
Also drop some old debugging messages associated to option insertion.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I guess I forgot to add it, nah, now it just works:
18:04:33.274066 IP6 ::1.1476 > ::1.5001: request (service=0)
18:04:33.334482 IP6 ::1.5001 > ::1.1476: reset (code=bad_service_code)
Ditched IP_DCCP_UNLOAD_HACK, as now we would have to do it for both
IPv6 and IPv4, so I'll come up with another way for freeing the
control sockets in upcoming changesets.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also fixes the layout of dccp_hdr short sequence numbers, problem
was not fatal now as we only support long (48 bits) sequence numbers.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. No need for ->ccid_init nor ->ccid_exit, this is what module_{init,exit}
does and anynways neither ccid2 nor ccid3 were using it.
2. Rename struct ccid to struct ccid_operations and introduce struct ccid
with a pointer to ccid_operations and rigth after it the rx or tx
private state.
3. Remove the pointer to the state of the half connections from struct
dccp_sock, now its derived thru ccid_priv() from the ccid pointer.
Now we also can implement the setsockopt for changing the CCID easily as
no ccid init routines can affect struct dccp_sock in any way that prevents
other CCIDs from working if a CCID switch operation is asked by apps.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing if the ccid being instantiated has these methods in
ccid_init().
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare circumstances 0 is returned by dccp_li_hist_calc_i_mean which
leads to a divide by zero in ccid3_hc_rx_packet_recv. Explicitly check
for zero return now. Update copyright notice at same time.
Found by Arnaldo.
Signed-off-by: Ian McDonald <imcdnzl@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocation for the optnames is similar to the DCCP options, with a
range for rx and tx half connection CCIDs.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also use some BUG_ON where appropriate and use LIMIT_NETDEBUG for the unlikely
cases where we, at this stage, want to know about, that in my tests hasn't
appeared in the radar.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
To match more closely what is described in RFC 3448.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: Ian McDonald <iam4@cs.waikato.ac.nz>
To start the timestamps with 0.0ms, easing the integer maths in the CCIDs, this
probably will be reworked to use the to be introduced struct timeval_offset
infrastructure out of skb_get_timestamp, etc.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
The initialization of ccid3hcrx_rtt to 5ms is just a bandaid, I'll continue
auditing the CCID3 HC rx codebase to fix this properly, probably I'll add a
feedback timer as suggested in the CCID3 draft.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This makes the send rate calculations behave way more closely to what
is specified, with the jitter previously seen on x and x_recv
disappearing completely on non lossy setups.
This resembles the tcp_data_snd_check code, that possibly we'll end up
using in DCCP as well, perhaps moving this code to
inet_connection_sock.
For now I'm doing the simplest implementation tho.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that applications can set dccp_sock->dccps_pkt_size, that in turn
is used in the CCID3 half connection init routines to set
ccid3hc[tr]x_s and use it in its rate calculations.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renaming it to dccp_rx_hist_detect_loss.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renaming it to dccp_rx_hist_add_packet.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And put this into net/dccp/ccids/lib/, where packet_history.[ch] will also be
moved and then we'll have a tfrc_lib.ko module that will be used by
dccp_ccid3.ko and other CCIDs that are variations of TFRC (RFC 3448).
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid open coding this all over the place.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introducing functions to add to or subtract from a timeval variable
and renaming now_delta to timeval_new_delta that calls do_gettimeofday
and then timeval_delta, that should be used when there are several
deltas made relative to the current time or setting variables to it,
so as to avoid calling do_gettimeofday excessively.
I'm leaving these "timeval_" prefixed funcions internal to DCCP for a
while till we're sure there are no subtle bugs in it.
It also is more correct as it checks if the number of usecs added to
or subtracted from a tv_usec field is more than 2 seconds.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not quite what I think we should have long term but improves
performance for now, so lets use it till we get CCID3 working well,
then we can think about using sk_write_queue, perhaps using some ideas
from Juwen Lai's old stack for 2.4.20.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch puts mostly read only data in the right section
(read_mostly), to help sharing of these data between CPUS without
memory ping pongs.
On one of my production machine, tcp_statistics was sitting in a
heavily modified cache line, so *every* SNMP update had to force a
reload.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And also hc_tx and hc_rx get_info functions for the CCIDs to fill in
information that is specific to them.
For now reusing struct tcp_info, later I'll try to figure out a better
solution, for now its really nice to get this kind of info:
[root@qemu ~]# ./ss -danemi
State Recv-Q Send-Q Local Addr:Port Peer Addr:Port
LISTEN 0 0 *:5001 *:* ino:628 sk:c1340040
mem:(r0,w0,f0,t0) cwnd:0 ssthresh:0
ESTAB 0 0 172.20.0.2:5001 172.20.0.1:32785 ino:629 sk:c13409a0
mem:(r0,w0,f0,t0) ts rto:1000 rtt:0.004/0 cwnd:0 ssthresh:0 rcv_rtt:61.377
This, for instance, shows that we're not congestion controlling ACKs,
as the above output is in the ttcp receiving host, and ttcp is a one
way app, i.e. the received never calls sendmsg, so
ccid_hc_tx_send_packet is never called, so the TX half connection
stays in TFRC_SSTATE_NO_SENT state and hctx_rtt is never calculated,
stays with the value set in ccid3_hc_tx_init, 4us, as show above in
milliseconds (0.004ms), upcoming patches will fix this.
rcv_rtt seems sane tho, matching ping results :-)
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using TIMESTAMP_ECHO and ELAPSED_TIME options received.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CCID3 keeps this variable in usecs, inet_connection_socks in jiffies,
so to avoid Mars orbiter losses lets reintroduce ccid3hctx_t_rto 8)
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes timestamp, timestamp echo, and elapsed time to use units of 10
usecs as per DCCP spec. This has been tested to verify that times are correct.
Also fixed up length and used hton/ntoh more.
Still to add in later patches:
- actually use elapsed time to adjust RTT
(commented out as was prior to this patch)
- send options at times more closely following the spec
(content is now correct)
Signed-off-by: Ian McDonald <iam4@cs.waikato.ac.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
may be a false warning if there always is something on ccid3hcrx_hist:
net/dccp/ccids/ccid3.c: In function 'ccid3_hc_rx_packet_recv':
net/dccp/ccids/ccid3.c:1634: warning: 'tstamp.tv_usec' may be used uninitialized in this function
net/dccp/ccids/ccid3.c:1634: warning: 'tstamp.tv_sec' may be used uninitialized in this function
const on inline functions doesn't have any effect:
net/dccp/dccp.h:64: warning: type qualifiers ignored on function return type
net/dccp/dccp.h:70: warning: type qualifiers ignored on function return type
net/dccp/dccp.h:76: warning: type qualifiers ignored on function return type
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only available if CONFIG_DEBUG_KERNEL is enabled in the "Kernel
Hacking" Menu.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As requested by Ian.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: Ian McDonald <iam4@cs.waikato.ac.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also changes the list_for_each_entry_safe_continue behaviour to match its
kerneldoc comment, that is, to start after the pos passed.
Also adds several helper functions from previously open coded fragments, making
the code more clear.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This way it gets closer to the TCP flow, where congestion window
checks are done, it seems we can map ccid_hc_tx_send_packet in
dccp_write_xmit to tcp_snd_wnd_test in tcp_write_xmit, a CCID2
decision should just fit in here as well...
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Development to this point was done on a subversion repository at:
http://oops.ghostprotocols.net:81/cgi-bin/viewcvs.cgi/dccp-2.6/
This repository will be kept at this site for the foreseable future,
so that interested parties can see the history of this code,
attributions, etc.
If I ever decide to take this offline I'll provide the full history at
some other suitable place.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
