Commit graph

267 commits

Author SHA1 Message Date
Mike Christie
d8196ed218 [SCSI] iscsi class, iscsi_tcp, iser, qla4xxx: add netdevname sysfs attr
iSCSI must support software iscsi (iscsi_tcp, iser), hardware iscsi (qla4xxx),
and partial offload (broadcom). To be able to allow each stack or driver
or port (virtual or physical) to be able to log into the same target portal
we use the initiator tuple [[HWADDRESS | NETDEVNAME], INITIATOR_NAME] and
the target tuple [TARGETNAME, CONN_ADDRESS, CONN_PORT] to id a session.
This patch adds the netdev name, which is used by software iscsi when
it binds a session to a netdevice using the SO_BINDTODEVICE sock opt.
It cannot use HWADDRESS because if someone did vlans then the same netdevice
will have the same mac and the initiator,target id will not be unique.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:38:04 -04:00
Mike Christie
2223696192 [SCSI] iscsi class, qla4xxx, iscsi_tcp: export local address
This patch exports the local address for the session. For
qla4xxx this is the ip of the hba's port. For software
this is the src addr of the socket.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:37:19 -04:00
Mike Christie
0ab823db86 [SCSI] qla4xxx: add iscsi_transport capps for fw capacilities
Userspace will want to know what the driver/FW/HW capabilites
when it comes to some operations like if the hardware can
do discovery or if it can store iscsi info like what target
was used for boot. This patch adds some new caps so userspace
can tell if the driver supports hardware/fw based sendtargets
discovery and if the hardware has some flash which may be
holding or can contain some iscsi target info
.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:36:14 -04:00
Mike Christie
1548271ece [SCSI] libiscsi: make can_queue configurable
This patch allows us to set can_queue and cmds_per_lun from userspace
when we create the session/host. From there we can set it on a per
target basis. The patch fully converts iscsi_tcp, but only hooks
up ib_iser for cmd_per_lun since it currently has a lots of preallocations
based on can_queue.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:34:46 -04:00
Mike Christie
77a23c21aa [SCSI] libiscsi: fix iscsi cmdsn allocation
The cmdsn allocation and pdu transmit code can race, and we can end
up sending a pdu with cmdsn 10 before a pdu with 5. The target will
then fail the connection/session. This patch fixes the problem by
delaying the cmdsn allocation until we are about to send the pdu.

This also removes the xmitmutex. We were using the connection xmitmutex
during error handling to handle races with mtask and ctask cleanup and
completion. For ctasks we now have nice refcounting and for the mtask,
if we hit the case where the mtask timesout and it is floating
around somewhere in the driver, we end up dropping the session.
And to handle session level cleanup, we use the xmit suspend bit
along with scsi_flush_queue and the session lock to make sure
that the xmit thread is not possibly transmitting a task while
we are trying to kill it.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:34:14 -04:00
Mike Christie
b2c6416736 [SCSI] iscsi class, iscsi_tcp, ib_iser: add sysfs chap file
The attached patches add sysfs files for the chap settings
to the iscsi transport class, iscsi_tcp and ib_iser. This is
needed for software iscsi because there are times when iscsid
can die and it will need to reread the values it was using.
And it is needed by qla4xxx for basic management opertaions.
This patch does not hook in qla4xxx yet, because I am not sure
the mbx command to use.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:58:58 -04:00
Mike Christie
857ae0bdb7 [SCSI] iscsi: Some fixes in preparation for bidirectional support - total_length
- Remove shadow of request length from struct iscsi_cmd_task.
- change all users to use scsi_cmnd->request_bufflen directly

(With bidi we will use scsi-ml API to retrieve in/out length)

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:58:22 -04:00
Mike Christie
d473cc7f15 [SCSI] iscsi: Some fixes in preparation for bidirectional support - exp_datasn
This patch fixes handling of expected datasn/r2tsn as received from
target. It is done according to: T10 rfc3720 section 3.2.2.3. Data Sequencing.

. unify expected datasn/r2tsn into one counter
. calculate than check expected datasn/r2tsn. On error print a message
  and fail the request. (TODO use iscsi retransmits)
. remove the FIXME   ;)
. avoid zero length memset

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:57:17 -04:00
Mike Christie
8ad5781ae9 [SCSI] iscsi class, qla4xxx, iscsi_tcp, ib_iser: export/set initiator name
For iscsi root boot, software iscsi needs to know what the BIOS/OF
initiator used for the initiator name so this puts it in sysfs
for userspace to be able to pick up.

For hw iscsi, it is nice to see what the card is using.

This patch adds the new param, and hooks in qla4xxx, iscsi_tcp, and ib_iser.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:56:40 -04:00
Mike Christie
0801c242a3 [SCSI] libiscsi, iscsi_tcp, ib_iser : add sw iscsi host get/set params helpers
iscsid and udev need to key off the hw address being
used so add some helpers for iser and iscsi tcp.

Also convert them

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:55:23 -04:00
Mike Christie
1d9bf13a9c [SCSI] iscsi class: add iscsi host set param event
The iscsi class uses the set_param event to set session
and connection params. This patch adds a set_host_param
so we can set host level values.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:51:03 -04:00
Mike Christie
2174a04ee7 [SCSI] iscsi_transport, qla4xxx: have class lookup host for drivers
We are going to be adding more host level sysfs attrs and
set_params, so this patch has them take a scsi_host instead
of either a scsi_host or host no.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:23:12 -04:00
Mike Christie
1819dc8143 [SCSI] iscsi_transport: export hw address
Add hw address sysfs file.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:02:51 -04:00
Christoph Hellwig
bcd92c9fbc [SCSI] introduce shost_priv helper
Currently accessing the scsi host private data is rather messy because
it comes as an unsigned long that always needs a cast first.  This patch
introduces a helper that does the cast called shost_priv.  It's similar
in spirit to netdev_priv for network drivers.

This is the first patch introducing the macro, and the second patch
in the series will convert esp and it's subdrivers as an example.
Further conversion will wait until the helper is in the tree to make
patch juggling easier.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-31 17:29:25 -04:00
FUJITA Tomonori
824d7b570b [SCSI] scsi_lib: add scatter/gather data buffer accessors
This adds a set of accessors for the scsi data buffer. This is in
preparation for chaining sg lists and bidirectional requests (and
possibly, the mid-layer dma mapping).

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-26 16:29:59 -05:00
James Smart
9ef3e4a452 [SCSI] fc_transport: fix sysfs deadlock on vport delete
When the vport attribute "delete" is used to delete the vport, sysfs
deadlocks waiting for the write to complete, which is waiting for the
sysfs teardown to complete. Moved this effort to a work_q element.

Took the opportunity to make some other cosmetic changes:
 - removed tabs in Doc file - replaced with expanded spaces
 - minor copyright text and author text updates
 - removed a bunch of trailing whitespace

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-26 11:47:58 -05:00
Tejun Heo
1dfcda06a6 [SCSI] kill scsi host template suspend/resume
With libata converted to use sdev->manage_start_stop for suspend and
resume, sht->suspend/resume() has no user left and low level
suspend/ressume should be taken care of by low level driver's
suspend/resume callbacks (e.g. PCI or PCMCIA driver callbacks).  This
patch removes sht->suspend/resume() callbacks.

This change is suggested by Christoph Hellwig.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-22 10:41:12 -05:00
James Smart
a53eb5e060 [SCSI] FC Transport support for vports based on NPIV
This patch provides support for FC virtual ports based on NPIV.
For information on the interfaces and design, please read the
Documentation/scsi/scsi_fc_transport.txt file enclosed within
the patch.

The RFC was originally posted here:
http://marc.info/?l=linux-scsi&m=117226959918393&w=2

Changes from the initial RFC:
- Bug fix: needed a transport_class_unregister() for the vport class
- Create a symlink to the vport in the shost device if it is not the
    parent of the vport.
- Made symbolic name writable so it can be set after creation
- Made the temporary fc_vport_identifiers struct private to the
transport.
- Deleted the vport_id field from the vport. I couldn't find any good
  use for it (and symname is a good replacement).
- Made the vport_state and vport_last_state "private" attributes.
  Added the fc_vport_set_state() helper function to manage state
  transitions
- Updated vport_create() to allow a vport to be created in a disabled
  state.
- Added INITIALIZING and FAILED vport states
- Added VPCERR_xxx defines for errors to be returned from vport_create()
- Created a Documentation/scsi/scsi_fc_transport.txt file that describes
  the interfaces and expected LLDD behaviors.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-16 09:36:15 -04:00
Christoph Hellwig
d7a54e30d3 [SCSI] sas_scsi_host: Convert to use the kthread API
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-06 09:33:17 -05:00
Michael Tokarev
d7b8bcb0a0 [SCSI] modalias for scsi devices
The following patch adds support for sysfs/uevent modalias
attribute for scsi devices (like disks, tapes, cdroms etc),
based on whatever current sd.c, sr.c, st.c and osst.c drivers
supports.

The modalias format is like this:

 scsi:type-0x04

(for TYPE_WORM, handled by sr.c now).

Several comments.

o This hexadecimal type value is because all TYPE_XXX constants
  in include/scsi/scsi.h are given in hex, but __stringify() will
  not convert them to decimal (so it will NOT be scsi:type-4).
  Since it does not really matter in which format it is, while
  both modalias in module and modalias attribute match each other,
  I descided to go for that 0x%02x format (and added a comment in
  include/scsi/scsi.h to keep them that way), instead of changing
  them all to decimal.

o There was no .uevent routine for SCSI bus.  It might be a good
  idea to add some more ueven environment variables in there.

o osst.c driver handles tapes too, like st.c, but only SOME tapes.
  With this setup, hotplug scripts (or whatever is used by the
  user) will try to load both st and osst modules for all SCSI
  tapes found, because both modules have scsi:type-0x01 alias).
  It is not harmful, but one extra module is no good either.
  It is possible to solve this, by exporting more info in
  modalias attribute, including vendor and device identification
  strings, so that modalias becomes something like
    scsi:type-0x12:vendor-Adaptec LTD:device-OnStream Tape Drive
  and having that, match for all 3 attributes, not only device
  type.  But oh well, vendor and device strings may be large,
  and they do contain spaces and whatnot.
  So I left them for now, awaiting for comments first.

Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-04-17 18:15:04 -04:00
Tejun Heo
c3c94c5a2f [SCSI] sd: implement START/STOP management
Implement SBC START/STOP management.  sdev->mange_start_stop is added.
When it's set to one, sd STOPs the device on suspend and shutdown and
STARTs it on resume.  sdev->manage_start_stop defaults is in sdev
instead of scsi_disk cdev to allow ->slave_config() override the
default configuration but is exported under scsi_disk sysfs node as
sdev->allow_restart is.

When manage_start_stop is zero (the default value), this patch doesn't
introduce any behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>

Rejections fixed and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-03-20 12:06:20 -05:00
James Bottomley
6c5f8ce1fb [SCSI] expose eh_timed_out to the host template
It looks like megaraid_sas at least needs this to throttle its commands
as they begin to time out.  The code keeps the existing transport
template use of eh_timed_out (and allows the transport to override the
host if they both have this callback).

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-03-20 10:56:49 -05:00
James Smart
c3d2350a84 [SCSI] fc_transport: update potential link speeds
This patch updates the FC transport for all speeds identified in
SM-HBA.  Note: it does not sync the "bit" definitions, as that is
actually insulated from user-space via the sysfs text string. (I could
do it, but it does introduce a potential binary-incompatibility).

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-03-20 10:52:04 -05:00
FUJITA Tomonori
bc7e380a6a [SCSI] tgt: fix sesnse buffer problems
This patch simplify the way to notify LLDs of the command completion
and addresses the following sense buffer problems:

- can't handle both data and sense.
- forces user-space to use aligned sense buffer

tgt copies sense_data from userspace to cmnd->sense_buffer (if
necessary), maps user-space pages (if necessary) and then calls
host->transfer_response (host->transfer_data is removed).

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-03-11 11:39:27 -05:00
Mike Christie
181011e04a [SCSI] tgt: rm bio hacks in scsi tgt
scsi tgt breaks up a command into multple scatterlists
if we cannot fit all the data in one. This was because
the block rq helpers did not support large requests and
because we can get a command of any old size so it is
hard to preallocate pages for scatterlist large enough
(we cannot really preallocate pages with the bio map
user path). In 2.6.20, we added large request support to
the block layer helper, blk_rq_map_user. And at LSF,
we talked about increasing SCSI_MAX_PHYS_SEGMENTS for
scsi tgt if we want to support really really :) large
(greater than 256 * PAGE_SIZE in the worst mapping case)
requests.

The only target currently implemented does not even support
the multiple scatterlists stuff and only supports smaller
requests, so this patch just coverts scsi tgt to use
blk_rq_map_user.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-03-11 11:31:33 -05:00
Mike Christie
bf32ed33e9 [SCSI] iscsi: rename DEFAULT_MAX_RECV_DATA_SEGMENT_LENGTH
This patch renames DEFAULT_MAX_RECV_DATA_SEGMENT_LENGTH to avoid
confusion with the drivers default values (DEFAULT_MAX_RECV_DATA_SEGMENT_LENGTH
is the iscsi RFC specific default).

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-03-11 11:26:50 -05:00
Martin K. Petersen
e73aec8247 [SCSI] sd: make printing use a common prefix
Make SCSI disk printing more consistent:

 - Define sd_printk(), sd_print_sense_hdr() and sd_print_result()

 - Move relevant header bits into sd.h

 - Remove all the legacy disk_name passing and use scsi_disk pointers
   where possible

 - Switch printk() lines to the new sd_ functions so that output is
   consistent

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-03-11 11:20:17 -05:00
Martin K. Petersen
a4d04a4cd9 [SCSI] Make error printing more verbose
This patch enhances SCSI error printing by:

 - Making use of scsi_print_result() in the completion functions.

 - Having scmd_printk() output the disk name (when applicable).

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-03-11 11:17:49 -05:00
Martin K. Petersen
684b7fe976 [SCSI] constants.c: cleanup, verbose result printing
Clean up constants.c and make result printing more user friendly:

 - Refactor the command and sense functions so that the actual
   formatting can be called from the various helper functions with the
   correct prefix.

 - Replace scsi_print_hostbyte() and scsi_print_driverbyte() with
   scsi_print_result() which is verbose when CONFIG_SCSI_CONSTANTS is
   on.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-03-11 11:14:02 -05:00
Linus Torvalds
5fc77247f7 Merge master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
  [SCSI] SCSI core: better initialization for sdev->scsi_level
  [SCSI] scsi_proc.c: display sdev->scsi_level correctly
  [SCSI] megaraid_sas: update version and author info
  [SCSI] megaraid_sas: return sync cache call with success
  [SCSI] megaraid_sas: replace pci_alloc_consitent with dma_alloc_coherent in ioctl path
  [SCSI] megaraid_sas: add bios_param in scsi_host_template
  [SCSI] megaraid_sas: do not process cmds if hw_crit_error is set
  [SCSI] scsi_transport.h should include scsi_device.h
  [SCSI] aic79xx: remove extra newline from info message
  [SCSI] scsi_scan.c: handle bad inquiry responses
  [SCSI] aic94xx: tie driver to the major number of the sequencer firmware
  [SCSI] lpfc: add PCI error recovery support
  [SCSI] megaraid: pci_module_init to pci_register_driver
  [SCSI] tgt: fix the user/kernel ring buffer interface
  [SCSI] sgiwd93: interfacing to wd33c93
  [SCSI] wd33c93: Fast SCSI with WD33C93B
2007-02-19 13:32:28 -08:00
Oliver Neukum
61bf54b71d USB Storage: indistinguishable devices with broken and unbroken firmware
there's a USB mass storage device which exists in two version. One
reports the correct size and the other does not. Apart from that they
are identical and cannot be told apart. Here's a heuristic based on the
empirical finding that drives have even sizes.


Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-16 15:32:19 -08:00
Rolf Eike Beer
a9b7320294 [SCSI] scsi_transport.h should include scsi_device.h
scsi_transport.h defines the inline function scsi_transport_device_data() that
dereferences a pointer of "struct scsi_device *".  Since the struct is not
known by the header this might break compilation.

Include scsi/scsi_device.h to not rely on users doing the correct magic
include order.

Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-02-16 10:14:42 -06:00
FUJITA Tomonori
930e99bd13 [SCSI] tgt: fix the user/kernel ring buffer interface
This patches fixes two bugs in the scsi target infrastructure's
user/kernel interface.

- It wrongly assumes that the ring buffer size of the interface (64KB)
is larger than or equal to the system page size. This patch sets the
ring buffer size to PAGE_SIZE if the system page size is larger.

- It uses PAGE_SIZE in the header file exported to userspace. This
patch removes it.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-02-16 09:40:56 -06:00
Linus Torvalds
5f0b1437e0 Merge master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (97 commits)
  [SCSI] zfcp: removed wrong comment
  [SCSI] zfcp: use of uninitialized variable
  [SCSI] zfcp: Invalid locking order
  [SCSI] aic79xx: use dma_get_required_mask()
  [SCSI] aic79xx: fix bracket mismatch in unused macro
  [SCSI] BusLogic: Replace 'boolean' by 'bool'
  [SCSI] advansys: clean up warnings
  [SCSI] 53c7xx: brackets fix in uncompiled code
  [SCSI] nsp_cs: remove old scsi code
  [SCSI] aic79xx: make ahd_match_scb() static
  [SCSI] DAC960: kmalloc->kzalloc/Casting cleanups
  [SCSI] scsi_kmap_atomic_sg(): check that local irqs are disabled
  [SCSI] Buslogic: local_irq_disable() is redundant after local_irq_save()
  [SCSI] aic94xx: update for v28 firmware
  [SCSI] scsi_error: Fix lost EH commands
  [SCSI] aic94xx: Add default bus reset handler
  [SCSI] aic94xx: Remove TMF result code munging
  [SCSI] libsas: Add an LU reset mechanism to the error handler
  [SCSI] libsas: Don't BUG when connecting two expanders via wide port
  [SCSI] st: fix Tape dies if wrong block size used, bug 7919
  ...
2007-02-11 11:44:25 -08:00
Robert P. J. Day
c376222960 [PATCH] Transform kmem_cache_alloc()+memset(0) -> kmem_cache_zalloc().
Replace appropriate pairs of "kmem_cache_alloc()" + "memset(0)" with the
corresponding "kmem_cache_zalloc()" call.

Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Roland McGrath <roland@redhat.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: Joel Becker <Joel.Becker@oracle.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-11 10:51:27 -08:00
James Bottomley
81b7bbd193 Merge branch 'linus'
Conflicts:

	drivers/scsi/ipr.c

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-02-10 13:45:43 -06:00
Al Viro
b437735645 [PATCH] iscsi endianness annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-09 09:14:07 -08:00
Darrick J. Wong
a9344e68ac [SCSI] libsas: Add an LU reset mechanism to the error handler
After discussion with andmike and dougg, it seems that the purpose of
eh_device_reset_handler is to issue LU resets, and that
eh_bus_reset_handler would be a more appropriate place for a phy reset.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-02-03 08:15:55 -06:00
Eric Moore
502c62f17a [SCSI] spi transport class: export spi_dv_pending
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-02-02 20:44:25 -06:00
Darrick J. Wong
ad689233be [SCSI] libsas: Handle SCSI commands that complete with failure codes
This patch moves the code that handles SAS failures out of the main EH
function and into a separate function.  It also detects commands that have
no sas_task (i.e. they completed, but with error data) and sends them into
scsi_error for processing.  This allows us to handle SCSI errors (and
enables auto-spinup as a side effect) instead of dropping them on the
floor and falling into an infinite loop.  It also requires the
implementation of a device reset function, which the SAS failure code has
been modified to employ for REQ_DEVICE_RESET.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-01-27 10:06:51 -06:00
Darrick J. Wong
6f63caae21 [SCSI] libsas: Clean up discovery failure handler code
sas_rphy_delete does two things: it removes the sas_rphy from the transport
layer and frees the sas_rphy.  This can be broken down into two functions,
sas_rphy_remove and sas_rphy_free; sas_rphy_remove is of interest to
sas_discover_root_expander because it calls functions that require
sas_rphy_add as a prerequisite and can fail (namely sas_discover_expander).
In that case, sas_discover_root_expander needs to be able to undo the effects
of sas_rphy_add yet leave the job of freeing the sas_rphy to the caller of
sas_discover_root_expander.

This patch also removes some unnecessary code from sas_discover_end_dev
to eliminate an unnecessary cycle of sas_notify_lldd_gone/found for SAS
devices, thus eliminating a sas_rphy_remove call (and fixing a race condition
where a SCSI target scan can come in between the gone and found call).
It also moves the sas_rphy_free calls into sas_discover_domain and
sas_ex_discover_end_dev to complement the sas_rphy_allocation via
sas_get_port_device.

This patch does not change the semantics of sas_rphy_delete.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-01-27 10:05:15 -06:00
Darrick J. Wong
6b0efb8516 [SCSI] libsas: Add SAS_HA state flags to avoid queueing events while unloading
Track sas_ha_struct state so that we ignore events that come in while
we're shutting things down.

Signed-off-by: Malahal Naineni <malahal@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-01-13 16:21:53 -06:00
Darrick J. Wong
396819fba8 [SCSI] libsas: Delay issuing ABORT TASK TMF until the error handler
sas_task_abort() should simply abort the upper-level SCSI command and wait
until the error handler to send the actual ABORT TASK command.  By
deferring things to the EH we simplify the concurrency coordination and
eliminate some race conditions.  Note that sas_task_abort has a few hooks
to handle libsas internal commands properly too.

Also rename do_sas_task_abort to __sas_task_abort just in case we really
want to abort the task *right now* and we don't have a scsi_cmnd attached
to the command.  This is a hook for libata internal commands to abort.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-01-13 16:18:06 -06:00
Darrick J. Wong
3ebf6922b0 [SCSI] libsas: Enable the EH strategy handler to reset a phy after a command
When a SAS LLDD needs to request a device port reset, it needs to have all
commands aborted before it can reset the port.  Since commands are put on
the EH's list in the order that they were queued, the LLDD can set a "need
reset" flag in the last task to be aborted so that the EH can reset the
port after all commands are aborted.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-01-13 16:17:27 -06:00
Darrick J. Wong
37958fb040 [SCSI] libsas: Remove SAS_TASK_INITIATOR_ABORTED flag
This flag is no longer necessary because we push tasks to be aborted into
the EH as soon as we possibly can, and let the SCSI EH code take care of
the coordination for which this flag was used.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-01-13 16:17:04 -06:00
Darrick J. Wong
acbf167d4a [SCSI] libsas: Add a sysfs knob to enable/disable a phy
This patch lets a user arbitrarily enable or disable a phy via sysfs.
Potential applications include shutting down a phy to replace one
lane of wide port, and (more importantly) providing a method for the
libata SATL to control the phy.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-01-13 16:13:00 -06:00
Darrick J. Wong
b218a0d8e2 [SCSI] libsas: Don't give scsi_cmnds to the EH if they never made it to the SAS LLDD or have already returned
On a system with many SAS targets, it appears possible that a scsi_cmnd
can time out without ever making it to the SAS LLDD or at the same time
that a completion is occurring.  In both of these cases, telling the
LLDD to abort the sas_task makes no sense because the LLDD won't know
about the sas_task; what we really want to do is to increase the timer.
Note that this involves creating another sas_task bit to indicate
whether or not the task has been sent to the LLDD; I could have
implemented this by slightly redefining SAS_TASK_STATE_PENDING, but
this way seems cleaner.

This second version amends the aic94xx portion to set the
TASK_AT_INITIATOR flag for all sas_tasks that were passed to
lldd_execute_task.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-01-13 16:12:39 -06:00
Christoph Lameter
e18b890bb0 [PATCH] slab: remove kmem_cache_t
Replace all uses of kmem_cache_t with struct kmem_cache.

The patch was generated using the following script:

	#!/bin/sh
	#
	# Replace one string by another in all the kernel sources.
	#

	set -e

	for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
		quilt add $file
		sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
		mv /tmp/$$ $file
		quilt refresh
	done

The script was run like this

	sh replace kmem_cache_t "struct kmem_cache"

Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 08:39:25 -08:00
David Howells
06328b4f79 Actually update the fixed up compile failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
2006-12-06 15:02:26 +00:00
David Howells
4796b71fbb Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:

	drivers/pcmcia/ds.c

Fix up merge failures with Linus's head and fix new compile failures.

Signed-Off-By: David Howells <dhowells@redhat.com>
2006-12-06 15:01:18 +00:00